Electrochemical Behaviours and Detection of Adenosine‐5¢‐triphosphate on an Ionic Liquid Modified Carbon Paste Electrode

In this paper a new electrochemical method based on the ionic liquid modified carbon paste electrode (IL‐CPE) was proposed for the determination of adenosine‐5′‐triphosphate (ATP) in a pH 4.5 Britton‐Robinson (B‐R) buffer solution. IL‐CPE was prepared by using 1‐butyl‐3‐methylimidazolium trifluoroacetate (BMIMCF₃COO) as the modifier. Cyclic voltammetry was used to investigate the electrochemical behaviors of ATP on the IL‐CPE, and the results indicated that IL‐CPE exhibited strong electrocatalytic ability to promote the oxidation of ATP with a single well‐defined irreversible adsorption‐controlled oxidation peak appeared. The electrochemical reaction parameters of ATP were calculated with the results of the electron transfer coefficient (α) as 0.40, the electron transfer number (n) as 1.17, the apparent heterogeneous electron transfer rate constant (ks) as 3.66 × 10^‐6 s^‐1 and the surface coverage (Γ_τ) as 2.48 × 10^‐9 mol cm^‐2. Under the selected conditions the proposed IL‐CPE showed good performances to the ATP detection in the concentration range from 0.1 to 1000.0 μmol L^‐1 with the detection limit as 3.65 × 10^‐8 mol L^‐1 (3σ) by differential pulse voltammetry. The method showed good selectivity to the ATP detection without the interferences of coexisting substances and was successfully applied to the ATP injection samples detection with satisfactory results.     

Electrochemical Behaviors of Adenosine‐5′‐triphosphate on Molecular Wire Modified Carbon Paste Electrode and Its Sensitive Detection

A new electrochemical method was proposed for the determination of adenosine‐5′‐triphosphate (ATP) based on the electrooxidation at a molecular wire (MW) modified carbon paste electrode (CPE), which was fabricated with diphenylacetylene (DPA) as the binder. A single well‐defined irreversible oxidation peak of ATP appeared on MW‐CPE with adsorption‐controlled process and enhanced electrochemical response in a pH 3.0 Britton‐Robinson buffer solution, which was due to the presence of high conductive DPA in the electrode. The electrochemical parameters of ATP were calculated with the electron transfer coefficient (α) as 0.54, the electron transfer number (n) as 1.9, the apparent heterogeneous electron transfer rate constant (k_s) as 2.67 × 10^?5 s^?1 and the surface coverage (Γ_T) as 4.15 × 10^?10 mol cm^?2. Under the selected conditions the oxidation peak current was proportional to ATP concentration in the range from 1.0 × 10^?7 mol L^?1 to 2.0 × 10^?3 mol L^?1 with the detection limit as 1.28 × 10^?8 mol L^?1 (3σ) by sensitive differential pulse voltammetry. The proposed method showed good selectivity without the interferences of coexisting substances and was successful applied to the ATP injection samples detection.     

Graphene Functionalized Graphite Electrode with Diphenylacetylene for Sensitive Electrochemical Determination of Adenosine‐5′‐triphosphate

In this paper a molecular wire modified carbon paste electrode (MW‐CPE) was firstly prepared by mixing graphite powder with diphenylacetylene (DPA). Then a graphene (GR) and chitosan (CTS) composite film was further modified on the surface of MW‐CPE to receive the graphene functionalized electrode (CTS‐GR/MW‐CPE), which was used for the sensitive electrochemical detection of adenosine‐5′‐triphosphate (ATP). The CTS‐GR/MW‐CPE exhibited excellent electrochemical performance and the electrochemical behavior of ATP on the CTS‐GR/MW‐CPE was carefully studied by cyclic voltammetry with an irreversible oxidation peak appearing at 1.369 V (vs. SCE). The electrochemical parameters such as charge transfer coefficient (α) and electrode reaction standard rate constant (k_s) were calculated with the results of 0.53 and 5.28×10^?6 s^?1, respectively. By using differential pulse voltammetry (DPV) as detection technique, the oxidation peak current showed good linear relationship with ATP concentration in the range from 1.0 nM to 700.0 µM with a detection limit of 0.342 nM (3σ). The common coexisting substances, such as uric acid, ascorbic acid and guanosine‐5′‐triphosphate (GTP), showed no interferences and the modified electrode was successfully applied to injection sample detection.     

Electrochemical Determination of Ascorbic Acid in Room Temperature Ionic Liquid BPPF6 Modified Carbon Paste Electrode

A room temperature ionic liquid N‐butylpyridinium hexafluorophosphate (BPPF₆) was used as a binder to make an ionic liquid modified carbon paste electrode (IL‐CPE), which showed good characteristics such as simple preparation procedure, fast electrochemical response and good conductivity. The electrochemical oxidation of ascorbic acid (AA) on the new IL‐CPE was carefully studied. The oxidation peak potential of AA on the IL‐CPE appeared at 109 mV (vs. SCE), which was about 338 mV decrease of the overpotential compared to that obtained on the traditional carbon paste electrode (CPE) and the oxidation peak current was increased for about four times. The electrochemical parameters of AA on the IL‐CPE were calculated with the charge transfer coefficient (α) and the electrode reaction rate constant (k_s) as 0.87 and 0.800 s^?1, respectively. Based on the relationship of the oxidation peak current and the concentration of AA a sensitive analytical method was established with cyclic voltammetry. The linear range for AA determination was in the range from 1.0×10^?5 to 3.0×10^?3 mol/L with the linear regression equation as I_p (μA)=?2.52–0.064C (μmol/L) (n=13, γ=0.9942) and the detection limit was calculated as 8.0×10^?6 mol/L (3σ). The proposed method was free of the interferences of coexisting substances such as dopamine (DA) and amino acids etc., and successfully applied to the vitamin C tablets determination.     

Differential Pulse Anodic Stripping Voltammetric Determination of Bismuth(III) with 1‐(2‐Pyridylazo)‐2‐naphthol and Ionic Liquid Modified Carbon Paste Electrode

In this paper 1‐(2‐pyridylazo)‐2‐naphthol (PAN) and ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) were mixed with graphite powder to get a modified carbon paste electrode (PAN‐IL‐CPE), which was further used for the sensitive determination of bismuth(III). By the co‐contribution of the formation of PAN‐Bi complex and the accumulation effect of IL, more bismuth(III) was electrodeposited on the surface of the PAN‐IL‐CPE. Then the reduced Bi was oxidized and detected by differential pulse anodic stripping voltammetry (DPASV) with the oxidation peak appeared at 0.17 V (vs. SCE). Under the optimal conditions the oxidation peak current was proportional to the bismuth(III) concentration in the range from 0.04 to 7.5 μmol L^?1 with the detection limit as 3.9 nmol L^?1. The proposed method was successfully applied to the stomach medicine sample detection with good recovery.     

Electrochemistry of adenosine-5′-diphosphate on ionic liquid modified carbon electrode and its detection

A sensitive electrochemical method was proposed for the determination of adenosine-5′-diphosphate (ADP) on an ionic liquid (IL) 1-(3-chloro-2-hydroxy-propyl)-3-methylimidazole chloride modified carbon paste electrode (CPE) in a pH 4.5 Britton-Robinson (B-R) buffer solution. Compared with CPE, IL modified CPE (CILE) showed strong electrocatalytic ability to promote the electrochemical oxidation of ADP. A well-defined irreversible oxidation peak of ADP appeared at +1.381 V with an adsorption-controlled process, which was due to the presence of high conductive IL on the electrode. The experimental conditions were optimized and the electrochemical parameters of ADP were calculated with the electron transfer coefficient (α) as 0.293, the electron transfer number (n) as 1.23, the apparent heterogeneous electron transfer rate constant (k ^s) as 3.325 × 10^?6 s^?1 and the surface coverage (Γ_T) as 0.92 × 10^?8 mol/cm². Under the optimum conditions, the oxidation peak current was linear to ADP concentration in the range from 3.0 to 1000.0 μmol/L with the detection limit as 2.78 μmol/L (3σ) by differential pulse voltammetry. The CILE also eliminated the interferences of commonly coexisting substances and was successfully applied to detect the ADP artificial samples.     

Enhanced Electrocatalytic Reduction of Oxadiargyl and Its Determination on 2‐(4‐((4‐Acetylphenyl)diazenyl)phenylamino)‐ethanol Modified Graphene‐Paste Electrode

The electrochemical behavior of oxadiargyl at a graphene‐paste electrode modified with an azo dye, 2‐(4‐((4‐acetylphenyl)diazenyl)phenylamino)ethanol (ADPE), ADPE/MGRPE was investigated. The modified electrode showed high electrocatalytic activity toward oxadiargyl. The apparent electron transfer rate constant (k_s) and charge transfer coefficient (α) between electrode and ADPE were 1.16 s^?1 and 0.41, respectively. The differential pulse voltammetry response of the modified graphene‐paste electrode was linear against the concentration of oxadiargyl in the range from 0.03 to 1.4 mg L^?1. The limit of detection was found to be 1.3 µg L^?1 (S/N=3). The practical analytical utility of this electrode was demonstrated by measurement of oxadiargyl in river water, soil and rice samples.     

Application of Polymer‐Modified Hanging Mercury Drop Electrode in the Indirect Determination of Certain β‐Lactam Antibiotics by Differential Pulse,Ion‐Exchange Voltammetry

A selective and sensitive polymer‐modified electrode was developed for β‐lactam antibiotics (cefaclor, amoxycillin and ampicillin) present in formulated and blood plasma samples for the quantitative analysis in aqueous environment. The detection was made using an ion‐exchange voltammetric technique, in differential pulse mode, on poly(N‐chloranil N,N,N′,N′‐tetramethylethylene diammonium dichloride)‐modified hanging mercury drop electrode of a three‐electrode system (PAR Model 303A) attached with a Polarographic Analyzer/Stripping Voltammeter (PAR Model 264A). Antibiotics, which are electroinactive compounds, were essentially converted to their electroactive oxazolone analogues through acid treatment under drastic conditions (0.1 mol L^?1 HCl, ～85 °C, 2 h). These analytes in the form of their respective oxazolones were indirectly analyzed by oxazolone entrapment in the polymeric film through ion‐exchange process at modified electrode surface (accumulation potential ?0.20 V (vs. Ag/AgCl), accumulation time 120 s, pH 7.4, KH₂PO₄‐NaOH buffer (ionic strength 0.1 mol L^?1), scan rate 10 mV s^?1, pulse amplitude 25 mV). The limit of detection of cefaclor‐derived oxazolone was found to be 2.12 nmol L^?1 (0.82 ppb, S/N 3, RSD 3.21%) in terms of cefaclor (a representative β‐lactam) concentration.     

Application of a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole/carbon nanotube modified glassy carbon electrode for voltammetric determination of hydrazine in water samples

The electrochemical behaviour of hydrazine at a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole‐triazole/carbon nanotube modified glassy carbon electrode has been studied. The modified electrode shows an excellent electrocatalytic activity for the oxidation of hydrazine and accelerates electron transfer rate. The electrocatalytic current increases linearly with hydrazine concentration in the range 0.5–700.0 μm and the detection limit for hydrazine was 33.0 ± 2.0 nm . The diffusion coefficient (D = 2.5 ± 0.1 × 10^?5 cm² s^?1) and kinetic parameters such as the electron transfer coefficient, (α = 0.52) and the heterogeneous rate constant (k′ = 5.5 ± 0.1 × 10^?3 cm s^?1) for hydrazine were determined using electrochemical approaches. Finally, the method was employed for the determination of hydrazine in water samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

Voltammetric Behavior of Sodium 7-Methoxyl-4＇-hydroxylisoflavone-3＇-sulfonate and Its Application

Voltammetric behavior of sodium 7‐methoxyl‐4′‐hydroxylisoflavone‐3′‐sulfonate (SMHS) in the aqueous solution from pH 1 to 5 was studied by linear sweep voltammetry, cyclic voltammetry and normal pulse voltammetry. Experimental results showed that in 0.2 mol*L^?1 sodium citrate‐hydrochloric acid buffer solution (pH=4.65), SMHS caused only one reduction wave at ?1.34 V (vs. saturated calomel electrode, SCE), which was an h‐reversible adsorptive wave of SMHS protonized involving one electron and one proton. The peak current of SMHS on linear sweep voltammogram was proportional to its concentration in the range of 8.0 × 10 ?8.0·10 mol*L^?1 (r = 0.995). and the detection limit was 5.0·10^?‐⁶mol*L^?1. The method was applied to determination of SMHS, in synthetic samples. In addition, its scavenging effect on superoxide anion radical was studied by the auto‐oxidation of pyrogallol in HCI‐tris buffer solution (pH = 8.2) in order to explain its peculiar biological effects. The experimental results proved that SMHS has antioxidant quality, and it is an efficient free radical scavenger of superoxide anion radical.     

Carbon Paste Electrode Incorporating 1‐[4‐(Ferrocenyl Ethynyl) Phenyl]‐1‐Ethanone for Electrocatalytic and Voltammetric Determination of Tryptophan

A carbon paste electrode spiked with 1‐[4‐ferrocenyl ethynyl) phenyl]‐1‐ethanone (4FEPE) was constructed by incorporation of 4FEPE in graphite powder‐paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that this electrode can catalyze the oxidation of tryptophan (Trp) in aqueous buffered solution. It has been found that under optimum condition (pH 7.00), the oxidation of Trp at the surface of such an electrode occurs at a potential about 200 mV less positive than at an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and rate constant for the chemical reaction between Trp and redox sites in 4FEPE modified carbon paste electrode (4FEPEMCPE) were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of Trp showed a linear dependent on the Trp concentrations and linear calibration curves were obtained in the ranges of 6.00×10^?6 M–3.35×10^?3 M and 8.50×10^?7 M–6.34×10^?5 M of Trp concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 1.80×10^?6 M and 5.60×10^?7 M by CV and DPV methods. This method was also examined as a selective, simple and precise new method for voltammetric determination of tryptophan in real sample.     

Voltammetric Determination of 3‐Nitrofluoranthene and 3‐Aminofluoranthene at Boron Doped Diamond Thin‐Film Electrode

The voltammetric behavior of 3‐nitrofluoranthene and 3‐aminofluoranthene was investigated in mixed methanol‐water solutions by differential pulse voltammetry (DPV) at boron doped diamond thin‐film electrode (BDDE). Optimum conditions have been found for determination of 3‐nitrofluoranthene in the concentration range of 2×10^?8–1×10^?6 mol L^?1, and for determination 3‐aminofluorathnene in the concentration range of 2×10^?7–1×10^?5 mol L^?1, respectively. Limits of determination were 3×10^?8 mol L^?1 (3‐nitrofluoranthene) and 2×10^?7 mol L^?1 (3‐aminofluoranthene).     

Voltammetric Determination of 4‐Nitrophenol and 5‐Nitrobenzimidazole Using Different Types of Silver Solid Amalgam Electrodes – A Comparative Study

The voltammetric behavior of two genotoxic nitro compounds (4‐nitrophenol and 5‐nitrobenzimidazole) has been investigated using direct current voltammetry (DCV) and differential pulse voltammetry (DPV) at a polished silver solid amalgam electrode (p‐AgSAE), a mercury meniscus modified silver solid amalgam electrode (m‐AgSAE), and a mercury film modified silver solid amalgam electrode (MF‐AgSAE). The optimum conditions have been evaluated for their determination in Britton‐Robinson buffer solutions. The limit of quantification (L_Q) for 5‐nitrobenzimidazole at p‐AgSAE was 0.77 µmol L^?1 (DCV) and 0.47 µmol L^?1 (DPV), at m‐AgSAE it was 0.32 µmol L^?1 (DCV) and 0.16 µmol L^?1 (DPV), and at MF‐AgSAE it was 0.97 µmol L^?1 (DCV) and 0.70 µmol L^?1 (DPV). For 4‐nitrophenol at p‐AgSAE, L_Q was 0.37 µmol L^?1 (DCV) and 0.32 µmol L^?1 (DPV), at m‐AgSAE it was 0.14 µmol L^?1 (DCV) and 0.1 µmol L^?1 (DPV), and at MF‐AgSAE, it was 0.87 µmol L^?1 (DCV) and 0.37 µmol L^?1 (DPV). Thorough comparative studies have shown that m‐AgSAE is the best sensor for voltammetric determination of the two model genotoxic compounds because it gives the lowest L_Q, is easier to prepare, and its surface can be easily renewed both chemically (by new amalgamation) and/or electrochemically (by imposition of cleaning pulses). The practical applicability of the newly developed methods was verified on model samples of drinking water.     

Fullerene‐β‐Cyclodextrin Conjugate Based Electrochemical Sensing Device for Ultrasensitive Detection of p‐Nitrophenol

The article describes the use of a fullerene (C₆₀)‐β‐cyclodextrin conjugate, synthesized via 1,3‐dipolar cycloaddition, for the ultrasensitive electrochemical detection of p‐nitrophenol. This conjugate was successfully immobilized on the surface of a glassy carbon electrode and the developed device showed high activity towards p‐nitrophenol due to the synergetic effect of C₆₀, the latter becoming highly conductive upon reduction. The determination of p‐nitrophenol was performed by using square wave voltammetry over a concentration range from 2.8×10^?9 mol L^?1 to 4.2×10^?7 mol L^?1 and the detection limit was calculated to be 1.2×10^?9 mol L^?1.     

Nanostructured Base Electrochemical Sensor for Simultaneous Quantification and Voltammetric Studies of Levodopa and Carbidopa in Pharmaceutical Products and Biological Samples

A novel carbon paste electrode modified with carbon nanotubes and 5‐amino‐2′‐ethyl‐biphenyl‐2‐ol (5AEB) was fabricated. The electrochemical study of the modified electrode, as well as its efficiency for electrocatalytic oxidation of levodopa (LD) and carbidopa (CD), is described. Cyclic voltammetry (CV) was used to investigate the redox properties of this modified electrode at various scan rates. The apparent charge transfer rate constant, k_s, and transfer coefficient, a, for electron transfer between 5AEB and CPE were calculated as 17.3 s^?1 and 0.5, respectively. Square wave voltammetry (SWV) exhibits a linear dynamic range from 2.5×10^?7 to 2.0×10^?4 M and a detection limit of 9.0×10^?8 M for LD.     

Evaluation of the Oxo‐bridged Dinuclear Ruthenium Ammine Complex as Redox Mediator in an Electrochemical Biosensor

The mediation of electron‐transfer by oxo‐bridged dinuclear ruthenium ammine [(bpy)₂(NH₃)Ru^III(µ‐O)Ru^III(NH₃)(bpy)₂]⁴⁺ for the oxidation of glucose was investigated by cyclic voltammetry. These ruthenium (III) complexes exhibit appropriate redox potentials of 0.131–0.09 V vs. SCE to act as electron‐transfer mediators. The plot of anodic current vs. the glucose concentration was linear in the concentration range between 2.52×10^?5 and 1.00×10^?4 mol L^?1. Moreover, the apparent Michaelis‐Menten kinetic (K_M^app) and the catalytic (K_cat) constants were 8.757×10^?6 mol L^?1 and 1,956 s^?1, respectively, demonstrating the efficiency of the ruthenium dinuclear oxo‐complex [(bpy)₂(NH₃)Ru^III(µ‐O)Ru^III(NH₃)(bpy)₂]⁴⁺ as mediator of redox electron‐transfer.     

A Cerium Hexacyanoferrate (III) Nanoparticle‐modified Carbon Paste Electrode: Voltammetric Characterization and Behavior in the Presence of Dopamine

This study describes a fast and simple methodology for the preparation of Cerium (III) Hexacyanoferrate (II) (CeHCF) nanoparticles (NPs). The NPs were characterized by fourier transform infrared (FTIR), x‐ray diffraction (XRD), scanning electron microscopy (SEM) and cyclic voltammetry (CV). The CeHCF cyclic voltammogram indicate a well‐defined redox pair assigned as Fe²⁺/Fe³⁺ in the presence of cerium (III), with a formal potential of E^θ′=0.29 V (v=100 mV s^?1, KNO₃; 1.0 mol/L, pH 7.0). The carbon paste electrode modified with CeHCF (CeHCF‐CPE) was applied to the catalytic electrooxidation of dopamine applying Differential Pulse Voltammetry (DPV). DPV showed linear response at two concentration ranges, from 9.0×10^?7 to 8.0×10^?6 and 9.0×10^?6 to 1.0×10^?4 mol/L, with an LOD of 1.9×10^?7 and 1.0×10^?5 mol/L, respectively. The CeHCF‐CPE exhibited selectivity against substances commonly found in biological samples, with redox potentials close to that of dopamine, such as urea and ascorbic acid (AA). Subsequently the CeHCF‐CPE was successfully applied to the detection of dopamine in simulated urine samples, with recovery percentages ranging between 99 and 103%.     

Sonovoltammetric Elucidation of Electron Transfer Rates: The Oxidation of Dimethyl‐p‐phenylenediamine in Aqueous Solution

The electrochemical oxidation of dimethyl‐p‐phenylenediamine (DMPD) in aqueous solution (pH 7 phosphate buffer) has been studied under conventional hydrodynamic and microelectrode voltammetric conditions and found to undergo a two‐electron electrochemically reversible oxidation. Upon the application of ultrasound to the system an observed shoulder emerges in the oxidation wave. This effect has been attributed to the resolution of the two‐electron transfer processes occurring: the first a relatively fast electron transfer (0.1 cm s^?1) followed by a second slower (10^?3 cm s^?1) electron transfer: under the very high mass transport rates induced by insonation an overpotential develops for the second electron transfer so leading to the observed voltammetric resolution. The range of mass transport conditions accessible via sonication allows the estimation of the two rate constants reported.     

Chemical Speciation of Antimony(III and V) in Water by Adsorptive Cathodic Stripping Voltammetry Using the 4‐(2‐Thiazolylazo) – Resorcinol

A simple adsorptive cathodic stripping voltammetry method has been developed for antimony (III and V) speciation using 4‐(2‐thiazolylazo) – resorcinol (TAR). The methodology involves controlled preconcentration at pH 5, during which antimony(III) – TAR complex is adsorbed onto a hanging mercury drop electrode followed by measuring the cathodic peak current (I_p,c) at ?0.39 V versus Ag/AgCl electrode. The plot of I_p,c versus antimony(III) concentration was linear in the range 1.35×10^?9–9.53×10^?8 mol L^?1.The LOD and LOQ for Sb(III) were found 4.06×10^?10 and 1.35×10^?9 mol L^?1, respectively. Antimony(V) species after reduction to antimony(III) with Na₂SO₃ were also determined. Analysis of antimony in environment water samples was applied satisfactorily.