载荷对纳米晶Co-Ni-Fe合金镀层摩擦磨损性能的影响

用脉冲电沉积技术制备表面平整光亮的纳米晶Co-Ni-Fe合金镀层.采用XRD、TEM、SEM、EDS等方法研究了纳米晶Co-Ni-Fe合金镀层的微观组织结构、表面形貌和合金成分.研究了干滑动摩擦条件下纳米晶镀层的摩擦磨损性能、磨损后的组织结构和硬度的变化.结果表明：纳米晶Co-Ni-Fe合金镀层的晶体结构为单相面心立方结构.镀层的摩擦系数和磨损量随着摩擦载荷的提高而增大,即镀层的耐磨性随载荷的提高而下降.摩擦磨损使纳米晶Co-Ni-Fe合金镀层发生晶粒长大,摩擦载荷越大,磨损后镀层的硬度越低.     

Influence of nano-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-reinforced oxide-dispersion-strengthened Cu on the mechanical and tribological properties of Cu-based composites

The mechanical and tribological properties of Cu-based powder metallurgy (P/M) friction composites containing 10wt%–50wt% oxide-dispersion-strengthened (ODS) Cu reinforced with nano-Al₂O₃ were investigated. Additionally, the friction and wear behaviors as well as the wear mechanism of the Cu-based composites were characterized by scanning electron microscopy (SEM) in conjunction with energy-dispersive X-ray spectroscopy (EDS) elemental mapping. The results indicated that the Cu-based friction composite containing 30wt% ODS Cu exhibited the highest hardness and shear strength. The average and instantaneous friction coefficient curves of this sample, when operated in a high-speed train at a speed of 300 km/h, were similar to those of a commercial disc brake pad produced by Knorr-Bremse AG (Germany). Additionally, the lowest linear wear loss of the obtained samples was (0.008 ± 0.001) mm per time per face, which is much lower than that of the Knorr-Bremse pad ((0.01 ± 0.001) mm). The excellent performance of the developed pad is a consequence of the formation of a dense oxide composite layer and its close combination with the pad body.     

La2O3对Ni基合金激光熔覆层组织和耐磨性的影响

在Ｎｉ基自熔合金粉末中添加不同量的Ｌａ２Ｏ３,并利用激光形成熔覆层。利用扫描电镜、Ｘ射线能谱仪、Ｘ射线衍射仪、显微硬度计和环块摩擦磨损实验机等对激光熔覆层显微组织、化学成分、相结构、显微硬度和摩擦磨损性能进行了研究。结果表明,在激光熔覆层中添加Ｌａ２Ｏ３能细化和净化显微组织;降低基材对熔覆层的稀释率;减小固溶体的晶格常数;提高熔覆层的显微硬度;降低熔覆层摩擦系数并提高其耐磨性能。该文还探讨了Ｌａ２Ｏ３作用的机理。     

Effect of Al<Subscript>2</Subscript>O<Subscript>3sf</Subscript> addition on the friction and wear properties of (SiC<Subscript>p</Subscript>+Al<Subscript>2</Subscript>O<Subscript>3sf</Subscript>)/Al2024 composites fabricated by pressure infiltration

Aluminum (Al) 2024 matrix composites reinforced with alumina short fibers (Al₂O_3sf) and silicon carbide particles (SiC_p) as wear-resistant materials were prepared by pressure infiltration in this study. Further, the effect of Al₂O_3sf on the friction and wear properties of the as-synthesized composites was systematically investigated, and the relationship between volume fraction and wear mechanism was discussed. The results showed that the addition of Al₂O_3sf, characterized by the ratio of Al₂O_3sf to SiC_p, significantly affected the properties of the composites and resulted in changes in wear mechanisms. When the volume ratio of Al₂O_3sf to SiC_p was increased from 0 to 1, the rate of wear mass loss (K_m) and coefficients of friction (COFs) of the composites decreased, and the wear mechanisms were abrasive wear and furrow wear. When the volume ratio was increased from 1 to 3, the COF decreased continuously; however, the K_m increased rapidly and the wear mechanism became adhesive wear.     

CuCrW(Al<Subscript>2</Subscript>O<Subscript>3</Subscript>) nanocomposite: mechanical alloying,microstructure, and tribological properties

The effect of alumina nanoparticle addition on the microstructure and tribological properties of a CuCrW alloy was investigated in this work. Mechanical alloying was carried out in a satellite ball mill. The tribological properties of the samples were evaluated using pin-on-disk wear tests with different pins (alumina, tungsten carbide, and steel pins). The results indicated that the tungsten carbide pin had a lower coefficient of friction than the alumina and steel pins because of its high hardness and low surface roughness. In addition, when the sliding rate was decreased, the weight-loss rate increased. The existence of alumina nanoparticles in the nanocomposite led to a lower weight-loss rate and to a change in the wear mechanism from adhesive to abrasive.     

Electromagnetic modification of faceted-faceted Ni<Subscript>31</Subscript>Si<Subscript>12</Subscript>-Ni<Subscript>2</Subscript>Si eutectic alloy

In an electromagnetic field, the morphology of a binary faceted-faceted (FF) Ni31Si12-Ni2Si eutectic microstructure and the alloy’s mechanical properties were investigated. Hardness experiments demonstrated that the solidified ingots were significantly strengthened, and the hardness was improved to 63.1 and 786.6 on the Rockwell hardness C and Vickers hardness scales, respectively. Tests of friction and wear in stirred FF eutectic alloys showed excellent anti-fatigue and anti-adhesion wear performance. Alloy changed from an anomalous microstructure to a refined quasi-regular structure, and there was an increase in the lamellar microstructure fraction. The formation process of the refined quasi-regular microstructure and the resulting mechanical properties were investigated.     

稀土在WC颗粒复合耐磨材料中的作用

为了提高ＷＣ硬质合金颗粒复合材料的耐磨性,向复合材料的金属基体中加入了不同数量的稀土。采用扫描电镜、Ｘ射线能谱仪、显微硬度计、台式冲击试验机以及销盘式磨损试验机等试验手段,对稀土加入量不同的几种ＷＣ硬质合金颗粒复合材料的金属基体进行了稀土分布及显微组织的分析,测定了基体组织的显微硬度及复合材料的韧性和耐磨性。研究结果表明,稀土富集于奥氏体与碳化物和奥氏体与共晶体两种界面处,少量固溶于奥氏体中。加入适量的稀土产生了明显的微合金化作用,使共晶组织显著细化,提高了金属基体的硬度和韧性以及复合材料的耐磨性。     

Effect of Al2O3 and Y2O3 on the corrosion behavior of ZrO2-benzotriazole nanostructured coatings applied on AA2024 via a sol-gel method

zirconia-based nanostructured coatings were deposited on AA2024 to improve the corrosion resistance properties. Three different nanostructured coatings, namely, zirconia-benzotriazole, zirconia-alumina-benzotriazole, and zirconia-yttria-benzotriazole, were applied on AA2024 via a sol-gel method using the dip-coating technique. Next, the coatings were annealed at 150℃ after each dipping period. The phases and morphologies of the coatings were investigated using grazing incidence X-ray diffraction (GIXRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), and atomic force microscopy (AFM). The corrosion properties were evaluated using electrochemical methods, including polarization and electrochemical impedance techniques in 3.5wt% NaCl solution. The obtained results confirm the formation of homogeneous and crack free zirconia-benzotriazole-based nanostructured coatings. The average roughness values for zirconia-benzotriazole, zirconia-alumina-benzotriazole, and zirconia-yttria-benzotriazole nanostructured coatings were 30, 8, and 6 nm, respectively. The presence of alumina as a stabilizer on zirconia coating was found to have a beneficial impact on the stability of the corrosion resistance for different immersion times. In fact, the addition of alumina resulted in the dominance of the healing behavior in competition with the corrosion process of zirconia-benzotriazole nanostructured coating.     

Corrosion-wear behavior of nanocrystalline Fe88Si12 alloy in acid and alkaline solutions

The corrosion-wear behavior of a nanocrystalline Fe₈₈Si₁₂ alloy disc coupled with a Si₃N₄ ball was investigated in acid (pH 3) and alkaline (pH 9) aqueous solutions. The dry wear was also measured for reference. The average friction coefficient of Fe₈₈Si₁₂ alloy in the pH 9 solution was approximately 0.2, which was lower than those observed for Fe₈₈Si₁₂ alloy in the pH 3 solution and in the case of dry wear. The fluctuation of the friction coefficient of samples subjected to the pH 9 solution also showed similar characteristics. The wear rate in the pH 9 solution slightly increased with increasing applied load. The wear rate was approximately one order of magnitude less than that in the pH 3 solution and was far lower than that in the case of dry wear, especially at high applied load. The wear traces of Fe₈₈Si₁₂ alloy under different wear conditions were examined and analyzed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results indicated that the tribo-chemical reactions that involve oxidation of the worn surface and hydrolysis of the Si₃N₄ ball in the acid solution were restricted in the pH 9 aqueous solution. Thus, water lubrication can effectively improve the wear resistance of nanocrystalline Fe₈₈Si₁₂ alloy in the pH 9 aqueous solution.     

钛合金表面稀土碳纳米管薄膜制备及其摩擦磨损性能分析

使用稀土对碳纳米管进行表面修饰,采用自组装技术在医用钛合金表面制备稀土改性碳纳米管复合薄膜,采用扫描电子显微镜（SEM）及X射线光电子能谱仪（XPS）对稀土改性碳纳米管复合薄膜的形貌及组成进行表征,并使用UMT-2MT型动-静摩擦系数精密测定仪评价薄膜的摩擦磨损性能.结果表明：在钛合金表面能够制备出硅烷薄膜及稀土改性碳纳米管复合薄膜;稀土元素能显著改善碳纳米管的表面活性,并作为基底与碳纳米管的联接介质;稀土改性碳纳米管复合薄膜的摩擦系数约为0.13,减摩效果显著,且薄膜具有良好的耐磨性能.
     

Mechanical properties and friction behaviors of CNT/AlSi<Subscript>10</Subscript>Mg composites produced by spark plasma sintering

The mechanical properties and friction behaviors of CNT/AlSi₁₀Mg composites produced by spark plasma sintering (SPS) were investigated. The results showed that the densities of the sintered composites gradually increased with increasing sintering temperature and that the highest microhardness and compressive strength were achieved in the specimen sintered at 450℃. CNTs dispersed uniformly in the AlSi₁₀Mg matrix when the addition of CNTs was less than 1.5wt%. However, when the addition of CNTs exceeded 1.5wt%, the aggregation of CNTs was clearly observed. Moreover, the mechanical properties (including the densities, compressive strength, and microhardness) of the composites changed with CNT content and reached a maximum value when the CNT content was 1.5wt%. Meanwhile, the minimum average friction coefficient and wear rate of the CNT/AlSi₁₀Mg composites were obtained with 1.0wt% CNTs.     

TC4合金氩弧熔覆TiN复合涂层的组织及耐磨性

为提高钛合金表面性能,以TiN粉和Ti粉为原料,利用氩弧熔覆技术,在TC4合金表面成功制备出TiN增强Ti基复合涂层。采用扫描电镜、X射线衍射仪分析了熔覆涂层的显微组织和物相组成;利用显微硬度仪、摩擦磨损试验机测试了复合涂层的显微硬度和室温干滑动磨损条件下的耐磨性能。结果表明:氩弧熔覆涂层组织均匀致密,熔覆层与基体呈冶金结合,熔覆涂层主要由TiN棒状树枝晶和TiN颗粒组成,复合涂层明显改善了TC4合金的表面硬度,涂层的最高显微硬度可达9.5 GPa;复合涂层在室温干滑动磨损实验条件下具有优异的耐磨性,磨损机制主要是磨粒磨损,其耐磨性较TC4合金基体提高近9倍。     

La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> TBCs toughened by Pt particles prepared by cathode plasma electrolytic deposition

La₂Zr₂O₇ thermal barrier coatings (TBCs) with dispersed Pt particles were prepared by cathode plasma electrolytic deposition (CPED) with ceramic balls added to the cathode region. Compared with the conventional CPED, when ceramic balls are used in the cathode region, the plasma discharge ignition current density decreases approximately 62-fold and the stable plasma discharges occur at the whole cathode surface. Such TBCs with a thickness of 100 μm exhibit a crack-free surface and are composed of pyrochlore-structured La₂Zr₂O₇. Cyclic oxidation, scratching, and thermal insulation capability tests show that such TBCs not only exhibit high resistance to oxidation and spallation but also provide good thermal insulation. These beneficial effects are attributed to the excellent properties of TBCs, such as good thermal insulation because of low thermal conductivity, high-temperature oxidation resistance because of low-oxygen diffusion rate, and good mechanical properties because of the toughening effect of Pt particles.     

MOSi2-淬火45#钢在油润滑下的摩擦学特性

利用M-200型磨损试验机考察了MoSi2-淬火45针仪分析讨论其磨损机理.结果表明:润滑油明显改善了MoSi2材料的摩擦学性能;MoSi2与淬火45#钢对摩在120～150 N载荷范围内表现出较好的摩擦磨损综合性能;其磨损机制主要表现为疲劳磨损、磨粒磨损和轻微粘着磨损.图4,参10.     

Cu-Zn-Al2O3 nanocomposites:study of microstructure,corrosion,and wear properties

Alumina nanoparticles were added to a Cu-Zn alloy to investigate their effect on the microstructural, tribological, and corrosion properties of the prepared alloys. Alloying was performed using a mixture of copper and zinc powders with 0vol% and 5vol% of α-Al nanopowder in a satellite ball mill. The results showed that the Cu-Zn solid solution formed after 18 h of mechanical alloying. The mechanically alloyed powder was compacted followed by sintering of the obtained green compacts at 750℃ for 30 min. Alumina nanoparticles were uniformly distributed in the matrix of the Cu-Zn alloy. The tribological properties were evaluated by pin-on-disk wear tests, which revealed that, upon the addition of alumina nanoparticles, the coefficient of friction and the wear rate were reduced to 20% and 40%, respectively. The corrosion properties of the samples exposed to a 3.5wt% NaCl solution were studied using the immersion and potentiodynamic polarization methods, which revealed that the addition of alumina nanoparticles reduced the corrosion current of the nanocomposite by 90%.     

Multi-color long-lasting phosphorescence of rare earth ions in CdSiO<Subscript>3</Subscript> matrix

A series of rare earth ions doped CdSiO3:RE^3 (RE=Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho,Er, Tin, Yb, Lu) multi-color long-lasting phosphorescence phosphors are prepared by the conventional hightemperature solid-state method. The results of XRD measurement indicate that the products fired under 1050~C for 3h have a good crystallization without any detectable amount of impurity phase. Rare earth ions doped CdSiO3 phosphors possess excellent Inmiuescence properties. When rare earth ions such as Y^3 , La^3 , Gd^3 , Lu^3 , Ce^3 , Nd^3 , Ho^3 , Er^3 ,Tm^3 and Yb^3 are introduced into the CdSiO3 host, one broadband centered at about 420 nm resulting from traps can be observed. In the case of other earth ions such as Pr^3 ,Sm^3 , Eu^3 , Tb^3 and Dy^3 , their characteristic line emitting as well as the -420 nm broadband luminescence can be obtained. The mixture of their characteristic line emitting with the -420 nm broadband Inminescence results in various afterglow color.     

碳纳米管对Ni60合金激光熔覆层的耐磨性影响

采用激光熔覆技术,在45#钢表面进行了镍基合金粉末添加碳纳米管的熔覆试验,对熔覆层横截面进行了硬度测试和显微组织分析,对熔覆层表面进行了X射线衍射物相分析和摩擦磨损试验.结果表明,碳纳米管能够提高镍基合金激光熔覆层的硬度和耐磨性能,当碳纳米管的质量分数为0.4%时,镍基合金激光熔覆层的耐磨性能最好.     

镍基纳米Al2O3粉末复合电刷镀镀层的耐磨性

为了进一步提高刷镀层的耐磨性 ,在 4 5 #钢基体上刷镀含有纳米 Al2 O3粉末的镍基复合镀层。通过光学金相显微镜、扫描电子显微镜对镀层显微组织进行分析 ,用显微硬度计测定了镀层和基体的硬度 ,在 SRV磨损试验机上进行了磨损试验 ,用表面形貌仪测量了镀层磨损量。试验结果表明 ,加入纳米 Al2 O3粉末的复合镀层的硬度要比单纯的致密镍镀层的硬度高。随着纳米 Al2 O3粉末加入量的增加 ,复合镀层硬度逐渐提高。含纳米 Al2 O3粉末的镍基复合镀层与单纯致密镍镀层相比 ,具有更高的耐磨性 ,将有广泛的应用前景。     

Effect of TiO<Subscript>2</Subscript> pigment gradation on the properties of thermal insulation coatings

This study was designed to evaluate the thermal performance and mechanical properties of coatings with different gradations of TiO₂ pigments. The solar reflectance, cooling performance, wash resistance, and film adhesion strength of the coatings were investigated. The influence of TiO₂ powder gradation on the final properties of the coatings was studed. The solar reflectance and the thermal insulation were observed to increase with increasing content of nanosized TiO₂. The mechanical properties of the coatings, such as their wash resistance and film adhesion strength, were observed to increase with increased incorporation of nanosized TiO₂. Such improvements in the properties of the coatings were attributed to the greater specific surface area and lower thermal conductivity of nanosized TiO₂ particles compared to normal TiO₂ particles.     

等离子喷涂Al_2O_3-TiO_2涂层的干摩擦磨损特性

利用等离子喷涂方法制备了Al2O3-TiO2涂层,测定了涂层的显微硬度和表观气孔率,并对涂层与GCr15钢配副,在不同P-V值及无润滑情况下进行了球 - 盘式摩擦磨损试验.试验结果表明:Al2O3-TiO2(w(TiO2)=13%)涂层在低速低载条件下具有显著的减摩抗磨性能;Al2O3-TiO2(w(TiO2)=20%)和Al2O3-TiO2(w(TiO2)=40%)涂层在高压力、转速工况下,具有优良的干摩擦特性.研究结果为实际生产选择涂层提供了依据.