Experimental investigation on diesel engine with diestrol-water micro emulsions

Experiments were conducted on a single cylinder direct injection diesel engine using diesel, biodiesel and biodiesel-diesel-ethanol (diestrol) water micro emulsion fuels to investigate the performance, emission and combustion characteristics of the engine under different load conditions at a constant speed of 1500 rpm. The results indicated that biodiesel and micro emulsion fuels had a higher brake specific fuel consumption (BSFC) than that of diesel. A slight improvement in the brake specific energy consumption (BSEC) was observed for micro emulsion fuels. The brake thermal efficiency of biodiesel and micro emulsion fuels were comparable to that of diesel. The emission characteristics like carbon monoxide (CO), carbon dioxide (CO₂), unburnt hydrocarbon (UHC), nitric oxide (NO) and smoke emissions for biodiesel and micro emulsion fuels were lower than diesel fuel at all load conditions. The cylinder gas pressure of micro emulsion fuels was lower than diesel at low loads but it became almost identical to diesel at medium and full load conditions. The heat release rate for micro emulsion fuels was higher than biodiesel and diesel fuels for all loads. Biodiesel showed shorter ignition delay for the entire load range and the longer ignition delay observed for micro emulsion fuels.     

A study on the performance and emission of a diesel engine fueled with Jatropha biodiesel oil and its blends

Biodiesel either in neat form or as a mixture with diesel fuel is widely investigated to solve the twin problem of depletion of fossil fuels and environmental degradation. The main objective of the present study is to compare performance, emission and combustion characteristics of biodiesel derived from non edible Jatropha oil in a dual fuel diesel engine with base line results of diesel fuel. The performance parameters evaluated were: brake thermal efficiency, brake specific fuel consumption, power output. As a part of combustion study, in-cylinder pressure, rate of pressure rise and heat release rates were evaluated. The emission parameters such as carbon monoxide, carbon dioxide, un-burnt hydrocarbon, oxides of nitrogen and smoke opacity with the different fuels were also measured and compared with base line results. The different properties of Jatropha oil after transestrification were within acceptable limits of standards as set by many countries. The brake thermal efficiency of Jatropha methyl ester and its blends with diesel were lower than diesel and brake specific energy consumption was found to be higher. However, HC, CO and CO₂ and smoke were found to be lower with Jatropha biodiesel fuel. NO_x emissions on Jatropha biodiesel and its blend were higher than Diesel. The results from the experiments suggest that biodiesel derived from non edible oil like Jatropha could be a good substitute to diesel fuel in diesel engine in the near future as far as decentralized energy production is concerned. In view of comparable engine performance and reduction in most of the engine emissions, it can be concluded and biodiesel derived from Jatropha and its blends could be used in a conventional diesel engine without any modification.     

Synergistic effect of hydrogen induction with biofuel obtained from winery waste (grapeseed oil) for CI engine application

The purpose of this study is to experimentally investigate the use of grapeseed oil as a fuel substitute obtained from biomass waste from winery industry and the synergic effect of hydrogen addition for compression ignition engine application. The experiments were carried out in a single cylinder, four stroke diesel engine for various loads and energy share of hydrogen. Combustion, performance and emission characteristics of grapeseed biodiesel, neat grapeseed oil and diesel have been analysed and compared with the results obtained with hydrogen induction in the intake manifold in dual fuel mode. At full load, maximum brake thermal efficiency of the engine with diesel, grapeseed biodiesel and neat grapeseed oil has increased from 32.34%, 30.28% and 25.94% to 36.04%, 33.97% and 30.95% for a maximum hydrogen energy share of 14.46%, 14.1% and 12.8% respectively. Although there is an increasing trend in Nitric Oxide emission with hydrogen induction, smoke, brake specific hydrocarbon, carbon monoxide, and carbon dioxide emissions respectively, reduces. Nitric oxide emission of Grapeseed biodiesel with maximum hydrogen share at full load is higher by 43.61% and smoke emission lower by 19.73% compared to biodiesel operation without hydrogen induction.     

Production of waste tyre oil and experimental investigation on combustion,engine performance and exhaust emissions

In this study, waste tyre was pyrolyzed at different conditions such as temperature, heating rate and inert purging gas (N₂) flow rate. Pyrolysis parameters were optimized. Optimum parameters were determined. The main objective of this study was to investigate combustion, performance and emissions of diesel and waste tyre oil fuel blend. Experimental investigation was performed in a single cylinder, direct injection, air cooled diesel engine at maximum engine torque speed of 2200 rpm and four different engine load including 3.75, 7.5, 11.25 and 15 Nm. The effects of waste tyre oil on combustion characteristics such as cylinder pressure, heat release rate, ignition delay (ID), combustion duration, engine performance were investigated. In-cylinder pressure and heat release rate increased with waste tyre oil fuel blend (W10) with the increase of engine load. In addition, ID was shortened with the increase of engine load for test fuels but it increased with the addition of waste tyre oil. Lower imep values were obtained because of the lower calorific value of waste tyre oil fuels. Maximum thermal efficiencies were determined as 28.27% and %25.12 with diesel and W10 respectively at 11.25 Nm engine load. When test results were examined, it was seen that waste tyre oil highly affected combustion characteristics, performance and emissions.     

Effect of injection parameters on the combustion and emission characteristics in a common-rail direct injection diesel engine fueled with waste cooking oil biodiesel

The objective of this paper was to study the effects of the injection pressure and injection timing on the combustion and emission characteristics in a single-cylinder common-rail direct injection (CRDI) diesel engine fueled with waste cooking oil (WCO) biodiesel and commercial diesel fuel. The fuel property including fatty acid composition for the biodiesel were measured and compared with those of the conventional diesel fuel. The engine tests were conducted at two injection pressures (80 and 160 MPa) and different injection timings from −25 to 0 crank angle degree (CAD) after top dead center (aTDC) under two different engine loads. The results showed that the indicated specific fuel consumption (ISFC) with respect to the injection timings of the biodiesel was higher than that of the diesel fuel under all experimental conditions. The peak cylinder pressure and the peak heat release rate of the biodiesel were slightly lower, while the ignition delay was slightly longer under all operating conditions. In terms of emissions, the biodiesel had benefits in reduction of smoke, carbon monoxide (CO), hydrocarbon (HC) emissions especially with high fuel injection pressure. The nitrogen oxide (NO_x) emissions of the biodiesel were relatively higher than those of the diesel under all experimental conditions.     

Biodiesel from cotton seed oil and its effect on engine performance and exhaust emissions

The use of biodiesel is rapidly expanding around the world, making it imperative to fully understand the impacts of biodiesel on the diesel engine combustion process and pollutant formation. Biodiesel is known as the mono-alkyl-esters of long chain fatty acids derived from renewable feedstocks, such as, vegetable oils or animal fats, for use in compression ignition engines. Different parameters for the optimization of biodiesel production were investigated in the first phase of this study, while in the next phase of the study performance test of a diesel engine with neat diesel fuel and biodiesel mixtures were carried out. Biodiesel was made by the well known transesterification process. Cottonseed oil (CSO) was selected for biodiesel production. Cottonseed is non-edible oil, thus food versus fuel conflict will not arise if this is used for biodiesel production. The transesterification results showed that with the variation of catalyst, methanol or ethanol, variation of biodiesel production was realized. However, the optimum conditions for biodiesel production are suggested in this paper. A maximum of 77% biodiesel was produced with 20% methanol in presence of 0.5% sodium hydroxide. The engine experimental results showed that exhaust emissions including carbon monoxide (CO) particulate matter (PM) and smoke emissions were reduced for all biodiesel mixtures. However, a slight increase in oxides of nitrogen (NO_x) emission was experienced for biodiesel mixtures.     

Performance,emission and combustion characteristics of a compression ignition engine operating on neat orange oil

Biomass derived fuels are preferred as alternate fuels for I.C Engines due to their abundant availability and renewable nature. Fuels such as methanol and ethanol have proved to be suitable alternate fuels in the transport sector. In the present work the performance, emission and combustion characteristics of a single cylinder, constant speed, direct injection diesel engine using orange oil as an alternate fuel were studied and the results are compared with the standard diesel fuel operation. Results indicated that the brake thermal efficiency was higher compared to diesel throughout the load spectra. Carbon monoxide (CO) and hydrocarbon (HC) emissions were lower and oxides of nitrogen (NO_x) were higher compared to diesel operation. Peak pressure and heat release rate were found to be higher for orange oil compared to diesel fuel operation.     

The effect of mixed nanoadditive‐blended diesel–water emulsion on the performance,combustion, and emission characteristics of a DI diesel engine

The present paper examines the impact of mixed nanoadditive (Al₂O₃ and ZnO) incorporated diesel–water emulsion on the combustion, performance, and emission of a single‐cylinder diesel engine under varying load conditions. The test fuels consist of constant fuel ratio of 88% diesel, 10% water, and 2% surfactant. Also, different concentrations of mixed nanoadditives—50 ppm, 100 ppm, and 150 ppm—are added to the test fuel. The ultrasonicator bath is employed for agitation or stirring of test fuels. The test results indicate that the mixed nanoadditives in diesel–water emulsion improve combustion characteristics, brake thermal efficiency, and brake‐specific fuel consumption, whereas the maximum improvement is achieved at full load. It is also determined from the test results that the nanoadditive‐blended test fuel showed a noticeable decrement in CO, NO_x, and hydrocarbon emissions as compared with neat diesel. The optimum results are obtained for D88S2W10ZA150 blend. Owing to the higher surface‐to‐volume ratio, enhanced atomization rate, high catalytic behavior, and shortened ignition delay are possible reasons to improve diesel engine working characteristics.     

相同氧含量醇类混合燃料燃烧和排放特性差异研究

对一台4缸发动机燃用相同氧浓度的不同醇类混合燃料进行了试验研究,以对比不同三元燃料柴油机在相同转速不同负荷情况下的燃烧特性和常规排放的差异。试验结果表明:甲醇混合燃料在醇类混合燃料中获得最高的燃烧压力,而丁醇混合燃料的热释放率最高。与普通柴油相比,戊醇混合燃料在不同混合物中具有相对最佳的CO和未燃碳氢排放,甲醇混合燃料可获得最优的氮氧化物排放;乙醇混合燃料减小颗粒物效果明显,最大可以减少22.4%～55.6%的颗粒物数量浓度和3.4%～12.8%的颗粒物粒径,其中乙醇混合燃料的核态颗粒物和聚集态颗粒物排放量也最低,戊醇混合燃料达到最高(除高负荷外)。     

A comprehensive study on performance,emission and combustion behavior of a compression ignition engine fuelled with WCO (waste cooking oil) emulsion as fuel

This work aims at evaluating the performance, emission and combustion of a diesel engine fuelled with WCO (waste cooking oil obtained from palm oil) and its emulsion as fuel. A single cylinder water-cooled diesel engine was used. Base data was generated with diesel and neat WCO as fuels. Subsequently, WCO oil was converted into its emulsion and tested. Neat WCO resulted in higher smoke, hydrocarbon and carbon monoxide emissions as compared to neat diesel. Significant reduction in all emission was achieved with the WCO emulsion. Cylinder peak pressure and maximum rate of pressure rise were found to be higher with WCO emulsion as compared to neat WCO mainly at high power outputs. Ignition delay was found as higher with neat WCO and its emulsion. It is concluded that WCO emulsion can be used in diesel engines without any modifications in the engine with superior performance and reduced emissions at high power outputs.     

Performance and combustion characteristic of CI engine fueled with hydrogen enriched diesel

The combustion of hydrogen–diesel blend fuel was investigated under simulated direct injection (DI) diesel engine conditions. The investigation presented in this paper concerns numerical analysis of neat diesel combustion mode and hydrogen enriched diesel combustion in a compression ignition (CI) engine. The parameters varied in this simulation included: H₂/diesel blend fuel ratio, engine speed, and air/fuel ratio. The study on the simultaneous combustion of hydrogen and diesel fuel was conducted with various hydrogen doses in the range from 0.05% to 50% (by volume) for different engine speed from 1000 – 4000 rpm and air/fuel ratios (A/F) varies from 10 – 80. The results show that, applying hydrogen as an extra fuel, which can be added to diesel fuel in the (CI) engine results in improved engine performance and reduce emissions compared to the case of neat diesel operation because this measure approaches the combustion process to constant volume. Moreover, small amounts of hydrogen when added to a diesel engine shorten the diesel ignition lag and, in this way, decrease the rate of pressure rise which provides better conditions for soft run of the engine. Comparative results are given for various hydrogen/diesel ratio, engine speeds and loads for conventional Diesel and dual fuel operation, revealing the effect of dual fuel combustion on engine performance and exhaust emissions.     

Dual-fuel diesel engine run with injected pilot biodiesel-diesel fuel blend with inducted oxy-hydrogen (HHO) gas

Oxy-hydrogen gas (HHO) is a carbon-free fuel, which is produced by the water electrolysis process. It can be used as an alternative to hydrogen since the current global hydrogen production and storage may not meet the required demand for transportation applications. This research work investigates the engine behavior of a compression ignition (CI) engine operated in dual-fuel mode by inducting HHO as a primary fuel and injecting two different pilot fuels viz., diesel, and JME20 (a blend composed of 80% diesel with 20% Jatropha methyl ester) at optimized engine conditions. The results revealed that; heat release rate, brake thermal efficiency, exhaust gas temperature, and nitric oxide emission are found to be higher about 5.2%, 1.1%, 18.6%, and 19.6% respectively, while unburnt hydrocarbon, carbon monoxide, and smoke emissions are reduced by about 33.3%, 29.4%, and 18.7% respectively in Opt.JME20 + HHO operation compared to that of the baseline data at maximum load.     

Increasing the efficiency of a diesel engine running on biodiesel through butanol fumigation

A single-cylinder, direct-injection diesel engine was tested with regular diesel oil, neat Jatropha biodiesel, and biodiesel with butanol injection into the inlet manifold. An engine fueled with neat biodiesel showed 5% reduction of the fuel conversion efficiency and 17% increase in specific fuel consumption relative to diesel oil. With butanol injection at a rate of 25% of the total fuel consumption, the efficiency was equivalent to that of diesel oil and specific fuel consumption was less than that of neat biodiesel. Engine emissions with biofuel were improved except for carbon monoxide and unburned hydrocarbons. It was concluded that the diesel engine can operate on the neat biofuel (biodiesel plus alcohol) with the fuel conversion efficiency equivalent to that of the diesel oil.     

Evaluating combustion,performance and emission characteristics of diesel engine using karanja oil methyl ester biodiesel blends enriched with HHO gas

With a specific end goal to take care of the worldwide demand for energy, a broad research is done to create alternative and cost effective fuel. The fundamental goal of this examination is to investigate the combustion, performance and emission characteristics of diesel engine using biodiesel blends enriched with HHO gas. The biodiesel blends are gotten by blending KOME obtained from transesterification of karanja oil in various proportions with neat diesel. The HHO gas is produced by the electrolysis of water in the presence of sodium bicarbonate electrolyte. The constant flow of HHO gas accompanied with biodiesel guarantees lessened brake specific fuel consumption by 2.41% at no load and 17.53% at full load with increased the brake thermal efficiency by 2.61% at no load and 21.67% at full load contrasted with neat diesel operation. Noteworthy decline in unburned hydrocarbon, carbon monoxide, carbon-dioxide emissions and particulate matter with the exception of NO_x discharge is encountered. The addition of EGR controls this hike in NO_x with a slight decline in the performance characteristics. It is clear that the addition of HHO gas with biodiesel blends along with EGR in the test engine improved the overall characterization of engine.     

Emission analysis on compression ignition engine fueled with lower concentrations of Pithecellobium dulce biodiesel‐diesel blends

The present study investigates the effect of Pithecellobium dulce biodiesel (PDBD) blends with diesel fuel on compression ignition (CI) engine emissions. Initially, PDBD was prepared by using a base transesteri?cation process. The GC‐MS, ¹H NMR, and Fourier transform infrared characterization of PDBD was carried out, and fuel properties were determined. The experiments were conducted on a single cylinder, CI engine using three blended fuels: PDBD5 (5% biodiesel and 95% diesel), PDBD10 (10% biodiesel and 90% diesel), and PDBD20 (20% biodiesel and 80% diesel). The experimental outcomes revealed that 20% of PDBD reduces 19.64% carbon monoxide, 17.64% hydrocarbon, and 6.73% oxides of nitrogen emissions. Furthermore, from this study, it was inferred that the PDBD20 blend could be used as an alternative fuel for CI engines with no modi?cations in engine design.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

A critical review: Application of methanol as a fuel for internal combustion engines and effects of blending methanol with diesel/biodiesel/ethanol on performance,emission, and combustion characteristics of engines

This article presents a comprehensive overview of methanol as a potential oxygenated fuel for internal combustion engines. Here two approaches have been examined to evaluate the utilization of methanol, namely blending with diesel/biodiesel/methanol and premixing with intake air or fumigation. In conventional compression ignition engines, up to 95% and 25% diesel can be replaced by methanol through fumigation and blending, respectively. Higher latent heat of vaporization of alcohol led to lower peak in-cylinder pressure and NO_x; however, it negatively affects thermal efficiency and hydrocarbon and carbon monoxide emissions. Fumigation of alcohol requires modifications in the existing engine, whereas blending needed surfactants or additives to produce stable alcohol–diesel blends. High injection pressure and late direct injection, methanol–diesel blends have shown lower emissions and proved their potential as a suitable replacement for ethanol–diesel blends from the components durability perspective.     

柴油机掺烧不同比例生物柴油的试验研究

将体积分数为10%2、0%、30%的生物柴油掺混到柴油里组成3种混合燃料,并连同纯柴油共4种燃料,在一台四缸增压中冷柴油机上进行性能、燃烧和排放特性的试验研究.结果表明,柴油机燃用生物柴油与柴油混合燃料的折合油耗率与燃用纯柴油时基本相当;燃用混合燃料的缸内最大爆发压力和压力升高率较低,着火时刻较晚;混合燃料的NOx和碳烟排放与燃用纯柴油时相比均有不同程度的降低,但混合燃料的HC和CO排放只是在1 500r/min时才较纯柴油低,当转速在2 300 r/min时,混合燃料的HC和CO排放更高.     

Effects of hydrogenation of fossil fuels with hydrogen and hydroxy gas on performance and emissions of internal combustion engines

Energy security is an important consideration for development of future transport fuels. Among the all gaseous fuels hydrogen or hydroxy (HHO) gas is considered to be one of the clean alternative fuels. Hydrogen is very flammable gas and storing and transporting of hydrogen gas safely is very difficult. Today, vehicles using pure hydrogen as fuel require stations with compressed or liquefied hydrogen stocks at high pressures from hydrogen production centres established with large investments.Different electrode design and different electrolytes have been tested to find the best electrode design and electrolyte for higher amount of HHO production using same electric energy. HHO is used as an additional fuel without storage tanks in the four strokes, 4-cylinder compression ignition engine and two-stroke, one-cylinder spark ignition engine without any structural changes. Later, previously developed commercially available dry cell HHO reactor used as a fuel additive to neat diesel fuel and biodiesel fuel mixtures. HHO gas is used to hydrogenate the compressed natural gas (CNG) and different amounts of HHO-CNG fuel mixtures are used in a pilot injection CI engine. Pure diesel fuel and diesel fuel + biodiesel mixtures with different volumetric flow rates are also used as pilot injection fuel in the test engine. The effects of HHO enrichment on engine performance and emissions in compression-ignition and spark-ignition engines have been examined in detail. It is found from the experiments that plate type reactor with NaOH produced more HHO gas with the same amount of catalyst and electric energy. All experimental results from Gasoline and Diesel Engines show that performance and exhaust emission values have improved with hydroxy gas addition to the fossil fuels except NO_x exhaust emissions. The maximum average improvements in terms of performance and emissions of the gasoline and the diesel engine are both graphically and numerically expressed in results and discussions. The maximum average improvements obtained for brake power, brake torque and BSFC values of the gasoline engine were 27%, 32.4% and 16.3%, respectively. Furthermore, maximum improvements in performance data obtained with the use of HHO enriched biodiesel fuel mixture in diesel engine were 8.31% for brake power, 7.1% for brake torque and 10% for BSFC.     

Comprehensive study of biodiesel fuel for HSDI engines in conventional and low temperature combustion conditions

In this research, an experimental investigation has been performed to give insight into the potential of biodiesel as an alternative fuel for High Speed Direct Injection (HSDI) diesel engines. The scope of this work has been broadened by comparing the combustion characteristics of diesel and biodiesel fuels in a wide range of engine loads and EGR conditions, including the high EGR rates expected for future diesel engines operating in the low temperature combustion (LTC) regime.The experimental work has been carried out in a single-cylinder engine running alternatively with diesel and biodiesel fuels. Conventional diesel fuel and neat biodiesel have been compared in terms of their combustion performance through a new methodology designed for isolating the actual effects of each fuel on diesel combustion, aside from their intrinsic differences in chemical composition.The analysis of the results has been sequentially divided into two progressive and complementary steps. Initially, the overall combustion performance of each fuel has been critically evaluated based on a set of parameters used as tracers of the combustion quality, such as the combustion duration or the indicated efficiency. With the knowledge obtained from this previous overview, the analysis focuses on the detailed influence of biodiesel on the different diesel combustion stages known ignition delay, premixed combustion and mixing controlled combustion, considering also the impact on CO and UHC pollutant emissions.The results of this research explain why the biodiesel fuel accelerates the diesel combustion process in all engine loads and EGR rates, even in those corresponding with LTC conditions, increasing its possibilities as alternative fuel for future DI diesel engines.