延边地区火山岩型金矿地球化学及成矿作用研究

延边地区北部大面积出露中生界（Ｊｓ）火山岩系，为正常的钙碱性系列，同玄武岩－安山岩－石英安山岩组成，以富含Ａｕ，Ａｇ，Ｓｂ，Ａｓ，Ｂｉ为特征，其中的金矿床可分为两类即蚀地型高温热液矿床和浅成中低温线热液成矿，同位素资料表明，其成矿热液主要来自火山岩浆。     

浙东地区火山岩银矿成矿作用的研究

浙东火山岩型银矿床成矿作用与浙东地区火山岩浆活动演化有着密切的关系，认为具有高丰度值的火山岩浆是成矿物质来源，其矿东地质成因属浅成低温火山岩浆混合热液贵金属矿床。建立银矿床蚀变矿化模式：分为硅化带（Ａｕ、Ａｇ、Ｚｎ、Ｂａ）、富银带（Ａｇ、（Ａｕ）１Ｐｂ、Ｚｎ、Ｍｎ、Ｓｂ）和贱金属带（Ｃｕ、Ｐｂ、Ｚｎ、（Ａｇ））三部分。     

贵州银厂坡银矿床蚀变过程中组分迁移特征

银厂坡银矿床碳酸盐化蚀变作用与银的矿化富集在空间上紧密相伴,这种蚀变作用导致矿石与围岩中组分有明显差异。本文通过定量计算阐明组分之间的迁移方向;计算表明在银的原生富集过程中,常量组分的带入与带出最不明显;而微量组分Ａｇ和Ｃｕ、Ｐｂ、Ｚｎ、Ａｓ、Ｓｂ、Ｃｄ、Ｇｅ带入围岩明显。在银的次生富集过程表现为Ａｇ和Ｃｕ、Ｐｂ、Ｃｄ、Ｇａ、Ｇｅ、ＲＥＥ、ＡｌＯ３、Ｆｅ２Ｏ３、ＭｎＯ、Ｋ２Ｏ、Ｐ２Ｏ５的强烈带入,以Ａｌ２Ｏ３、Ｆｅ２Ｏ３、Ｋ２Ｏ、Ｐ２Ｏ５带入强度最大,这是由于ＣａＯ、ＭｇＯ被淋滤,体积亏损造成强烈带入的假象,而Ａｓ、Ｓｂ、Ｚｎ、Ｖ、Ｃｒ、Ｃｏ、Ｎｉ、ＣａＯ、ＭｇＯ为自围岩中带出组分,以ＣａＯ、ＭｇＯ带出强度最大。ＲＥＥ除原生富集的弱蚀变白岩→矿化白云岩表现为带出外,其余原富集过程均表现为带入围岩。造成组分发生迁     

白银矿田含矿围岩蚀变特征及其意义

对北祁连加里东褶皱带中白银矿田成矿蚀变岩的研究表明,蚀变岩筒具有明显的分带性：中心部位是绿泥石化带,汉发泥石＋石英＋黄铁矿组合为特征;其外是绢云母硅化带,以绢云母＋石英＋黄铁矿组合为特征,最外则是蚀变带或弱蚀变带。岩石化学上,随着蚀变作用增强,ＭｇＯ、Ｋ２Ｏ、ＦｅＯ增加,而Ｎａ２Ｏ降低;白银矿田成矿系列中Ｃｕ－Ｚｎ型到Ｃｕ－Ｐｂ－Ｚｎ型、Ｐｂ－Ｚｎ－Ｃｕ型矿床,绿泥石中ＭｇＯ、Ｓｉ２Ｏ和降低趋势。     

西太平洋冲绳海槽烟囱硫化物矿床矿石化学特征与分带型式

西太平洋冲绳海槽烟囱式硫化物矿床分布于琉球弧后扩张盆地、产于尹是名洼陷盆地（深１４００ｍ），其特征与日本黑矿类似。硫化物矿石及烟囱主要有３种化学类型：Ｐｂ－Ｚｎ－Ｂａ型、Ｚｎ－Ｐｂ型和Ｃｕ－Ｚｎ型，三者分别代表温度不断升高的热液体系的早、中、晚３个成矿阶段产物，其中，Ｐｂ－Ｚｎ－Ｂａ矿石及烟囱形成于高ｆｏ２环境和高流速、低温、富Ｐｂ、Ｚｎ、Ｂａ热液体系，Ｃｕ－Ｚｎ矿石及烟囱形成于低流速、高温、富Ｃｕ热液体系，Ｚｎ－Ｐｂ矿石则介于其间。硫化物烟囱显示明显的矿物－化学分带。在Ｐｂ－Ｚｎ－Ｂａ矿石（烟囱），Ｚｎ、Ｃｄ集中于烟囱中央，Ｂａ、Ｆｅ、Ａｓ、Ｓｂ、Ａｇ、Ｐｂ集中于烟囱外带，Ｃｕ则富集于烟囱中外部。在Ｃｕ－Ｚｎ矿石，Ａｓ、Ｓｂ、Ｆｅ、Ａｇ、Ａｕ仍富集于烟囱外带，Ｃｕ、Ｚｎ、Ｐｂ则在烟囱中央富集。依此元素化学分带型式，建立了古代黑矿硫化物矿体分带与硫化物堆积模式。     

新矿物硒锑矿形成的地质地球化学环境

在我国贵州某低中温热卤水改造层控铀－汞矿床和湖南某古岩溶热造铀矿床中几乎同时发现了新矿物─—硒锑矿（Ｓｂ＿２Ｓｅ＿３）．该矿物的单晶呈细板条状、针状，集合体呈放射状、禾束状。确定硒锑矿形成于１３０─１６０℃富含Ｃａ￣（２＋），Ｎａ￣＋，Ｍｇ￣（２＋），ＳＯ＿４￣２－，ＨＣＯ＿３￣－的弱酸性─弱碱性热液，伴生一套典型的低中温热液矿物组合和围岩蚀变。硒锑矿是低中温热液标型矿物     

广东长坑金银矿床含矿硅质岩的地球化学与成因

长坑矿床的金、银矿化与硅质岩关系最为密切，角砾状硅质岩矿体具层控和断裂控制双重特点。含矿硅质岩的ＳｉＯ２含量为７３％～９２％，其平均值（８８％）与海底热液燧石相近，但硅质金矿石的ＴｉＯ２、Ａｌ２Ｏ３、ＴＦｅ、ＣａＯ、Ｋ２Ｏ和银矿石的ＣａＯ、ＦｅＯ含量平均值明显高于热水沉积硅质岩；在Ａｌ Ｆｅ Ｍｎ成分三角图上，含矿硅质岩在水成区和热液区均有分布。虽然矿化硅质岩的稀土成分具海底热水沉积岩的特点，即总量较低，具Ｃｅ负异常，但其模式曲线与围岩相似。硅质矿石相对富Ｆｅ，贫Ｃｕ、Ｃｏ、Ｎｉ，过渡元素配分模式继承了围岩的特点。结合硅质矿体的地质产状、矿化年龄与成矿流体来源，认为硅质矿石主要形成于热液对围岩和裂隙的交代、充填作用，但不排除早期热水沉积硅质岩存在的可能性。     

浙西石炭纪层状硅质岩地球化学特征及其意义

在浙西石炭纪地层中存在与地层整合产出的层状硅质岩。硅质岩中ＦｅＯ、ＭｎＯ、ＴｉＯ２、Ａｌ２Ｏ３、ＭｇＯ、ＣａＯ、Ｎａ２Ｏ、Ｋ２Ｏ等含量相对较高，富集Ａｓ、Ｓｂ、Ｂｉ、Ａｕ、Ａｇ、Ｇａ，Ｆｅ２Ｏ３／ＦｅＯ、ＳｉＯ２／Ａｌ２Ｏ３、ＳｉＯ２／（Ｎａ２Ｏ＋Ｋ２Ｏ）、ＳｉＯ２／ＭｇＯ比值较小，稀土元素总量低，Ｃｅ弱负异常，重稀土相对富集，包裹体富含气相组份ＣＨ４、ＣＯ２、Ｎ２、ＣＯ、Ｈ２，具热水沉积硅质岩的地球化学特征。在Ｆｅ—Ｍｎ—（Ｎｉ＋Ｃｏ＋Ｃｕ）三角图及ＳｉＯ２—Ａｌ２Ｏ３、ＳｉＯ２—Ｆｅ２Ｏ３图上均属于热水沉积硅质岩。硅质岩中硅、氧同位素也显示其热水成因之特点。硅质岩的硅同位素和稀土元素Ｃｅ／Ｃｅ※值表明本区层状硅质岩主要是在浅海环境下沉积的。硅质岩的形成温度较高，为９８℃～１５２℃     

两种未定名硒矿物的研究

本文研究的两种未定名硒矿物产于贵州省５０４轴汞钼多金属矿床内的含铀－硒方解石脉中。经ＪＣＸＡ－７３３型电子探针Ｘ射线显微分析仪分析，其平均化学成分（重量％）分别为：Ｓｅ４８．８０，Ｓ０．１１，Ｃｕ１７．４２，Ｈｇ１．６５，Ｓｂ３４．０８，Ｎｉ０．０２，Ｆｅ０．０５，Ａｓ０．５８及Ｓｅ３８．８９，Ｓ１．６５，Ｃｕ１７．７９，Ｈｇ２１．６３，Ｓｂ１９．５４，Ｎｉ０．０３，Ｆｅ０．１５，Ａｓ０．３３。它     

大兴安岭东北部首个三叠纪银矿床地质特征及矿床成因分析

二道坎银矿床是大兴安岭东北部首次发现的三叠纪大型银矿床。矿体位于上志留统—中泥盆统泥鳅河组沉积岩中,辉绿岩脉与矿体密切共生。矿石为石英脉胶结的构造角砾岩,目前以地表氧化矿石为主。矿石中金属矿物主要为黄铁矿、方铅矿,其次为闪锌矿、黄铜矿、黝铜矿、赤铁矿、磁铁矿等,含银矿物主要为辉银矿和硫锑银矿。矿石结构主要为粒状结构和固溶体分离结构,构造有致密块状、脉状-网脉状、角砾状和条带状构造等。成矿阶段主要为沥青-黄铁矿-石英阶段、石英-含银多金属硫化物阶段和石英-方解石阶段。矿区蚀变类型有硅化、绿泥石化、绢云母化、绿帘石化、碳酸盐化和赤铁矿化。综合分析认为二道坎银矿床为晚三叠世形成的浅成低温热液型银矿床。     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.