Critical pitting temperature dependence of 2205 duplex stainless steel on dichromate ion concentration in chloride medium

In this study, the influence of various concentrations of dichromate and chloride ions on critical pitting temperature (CPT) of duplex stainless steel 2205 (DSS 2205) is investigated by employing potentiodynamic and potentiostatic CPT measurement methods. Potentiostatic results indicate that by adding 0.01 M to 0.1 M NaCl solution the CPT raised by 12 °C. Based on potentiodynamic CPT measurements in the solutions with ratio equal to one for solutions containing 0.1 M NaCl + 0.1 M and 0.01 M NaCl + 0.01 M , no CPT was detected up to 75 °C.     

Prevention of passive film breakdown and corrosion of iron in 0.1 M KClO4 with and without Cl by covering with an ultrathin two-dimensional polymer coating and healing treatment in 0.1 M NaNO3

A two-dimensional polymer coating, the self-assembled monolayer of 16-hydroxy hexadecanoate ion HO(CH₂)₁₅ modified with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃ was prepared on the passivated iron electrode and further, the passive film was healed by additional treatment in 0.1 M NaNO₃. This electrode was immersed in oxygenated 0.1 M KClO₄ solutions with and without 1 × 10⁻⁴ to 1 × 10⁻² M of Cl⁻. Protection of passive film against breakdown by covering the electrode with the polymer coating was examined by monitoring the open-circuit potential during immersion in the solutions for many hours to determine the time for passive film breakdown, t_bd. Repeated polarization measurements were carried out during immersion in these solutions for obtaining the protective efficiency, P. The t_bd value of the passivated, polymer-coated and healed electrode in 0.1 M KClO₄ solutions with and without Cl⁻ increased with a decrease in the concentration of Cl⁻. No breakdown occurred on the electrode during immersion in 0.1 M KClO₄ solutions with and without 1 × 10⁻⁴ of Cl⁻ for 360 h. The P values were extremely high, more than 99.9% before t_bd, indicating complete protection of iron from corrosion. The effect of healing treatment in 0.1 M NaNO₃ on passive film breakdown was investigated by electron-probe microanalysis.     

Protection of passivated iron from corrosion in 0.1 M KClO4 with and without Cl by coverage with a two-dimensional polymer film of carboxylate ion self-assembled monolayer

A film of two-dimensional polymer was prepared on an iron electrode passivated in a borate buffer solution at pH 8.49, derivatized with 16-hydroxyhexadecanoate ion and then modified with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. The protective ability of the polymer film adsorbed on passivated iron was examined by polarization measurement in oxygenated 0.1 M KClO₄ solutions with and without 1 × 10⁻⁴ and 1 × 10⁻³ M of Cl⁻. The values of the open-circuit potential, E_oc were monitored with the immersion time, t in these solutions. The E_oc value of the passivated electrode in 0.1 M KClO₄ was maintained high, more than −0.2 V/SCE in the initial region of t up to 10 h, indicating the presence of a passive film on the electrode. Thereafter, E_oc decreased to −0.4 V/SCE abruptly, exhibiting breakdown of the passive film. The value of the passivated electrode covered with the polymer film remained almost constant around −0.04 V/SCE during immersion for 45 h. The protective efficiency, P (%) of the polymer film on passivated iron was extremely high, more than 99.9% unless the passive film was broken down, indicating complete protection of iron against corrosion. The times for breakdown on the passivated electrode and polymer-coated one diminished with an increase in the concentration of Cl⁻. The polymer-coated surface was analyzed by electron-probe microanalysis after immersion in 0.1 M KClO₄ for 24 h.     

Effect of 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone on the corrosion of aged 18 Ni 250 grade maraging steel in phosphoric acid solution

4-(N,N-diethylamino)benzaldehyde thiosemicarbazone (DEABT) was studied for its corrosion inhibition property on the corrosion of aged 18 Ni 250 grade maraging steel in 0.67 M phosphoric acid at 30–50 °C by potentiodynamic polarization, EIS and weight loss techniques. Inhibition efficiency of DEABT was found to increase with the increase in DEABT concentration and decrease with the increase in temperature. The activation energy E_a and other thermodynamic parameters (Δ, Δ, Δ) have been evaluated and discussed. The adsorption of DEABT on aged maraging steel surface obeys the Langmuir adsorption isotherm model and the inhibitor showed mixed type inhibition behavior.     

Critical pitting temperature (CPT) assessment of 2205 duplex stainless steel in 0.1 M NaCl at various molybdate concentrations

In this study, the influence of various concentrations of molybdate () on critical pitting temperature (CPT) of duplex stainless steel 2205 (DSS 2205) in 0.1 M NaCl solution has been investigated by employing potentiodynamic and potentiostatic CPT measurements methods. No significant increase in CPT was observed in the presence of 0.0001 and 0.001 M molybdate. However, addition of 0.01 M increases 10 °C in CPT and pitting corrosion was not observed in solution containing 0.1 M molybdate up to 85 °C. Potentiostatic CPT measurements showed CPT values of 68 and more than 85 °C in 0.01 and 0.1 M molybdate concentrations, respectively.     

Preparation of a two-dimensional polymer film on passivated iron by modification of a carboxylate ion self-assembled monolayer with alkyltriethoxysilanes for preventing passive film breakdown

The effect of an ultrathin, regularly arranged polymer film on prevention of passive film breakdown on iron in the presence of chloride ion was investigated. The film of two-dimensional polymer was prepared by modification of a 16-hydroxyhexadecanoate ion self-assembled monolayer adsorbed on a passivated iron electrode with 1,2-bis(triethoxysilyl)ethane(C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octyltriethoxysilane C₈H₁₇Si(OC₂H₅)₃. The pitting potentials of the passivated electrodes bare and covered with the polymer film were determined by anodic polarization measurements in a borate buffer solution containing 0.1 M of Cl⁻. The pitting potential of the coated electrode was higher than that of the uncoated one, indicating prevention of passive film breakdown. No breakdown was observed over the potential range in the passive and transpassive regions by covering the passive film with the well-arranged two-dimensional polymer film. The film was characterized by X-ray photoelectron and FTIR reflection spectroscopies and measurement of the contact angle with a drop of water.     

Photoelectron spectroscopy study of the inhibition of mild steel corrosion by molybdate and nitrite anions

Passive films formed on mild steel in aqueous 8.6 mM NaCl solutions (pH 8), containing either or , have been studied with X-ray photoelectron spectroscopy. For either anion these films are ∼5 nm deep, and the primary chemical state of iron is Fe³⁺. Following exposure to , the film consists of a sub-layer (∼4.1 nm) composed largely of ferric oxide/hydroxide, overlaid by Fe₂(MoO₄)₃ (∼0.6 nm). As regards , spectra are consistent with the film being closely related to γ-Fe₂O₃. Furthermore, a reduction product of , potentially N₂, is present, displaying a depth profile comparable to that of molybdate.     

Electrochemical behavior of tin in sodium borate solutions and the effect of halide ions and some inorganic inhibitors

The corrosion of tin electrode in sodium borate (Na₂B₄O₇) solutions was investigated using cyclic voltammetry and potentiostatic current transient techniques. In absence of halide ions, the E/j response exhibits active/passive transition. The active region involves one anodic peak corresponding to the formation of Sn(OH)₂ and/or SnO. Addition of Cl⁻, Br⁻ or I⁻ (C ? 0.01 M) ions inhibits the active dissolution of tin, but higher concentrations enhance the active dissolution and tend to breakdown the passive film and induce pitting attack. The effect of , , and as inorganic inhibitors on the pitting corrosion of tin in (0.1 M Na₂B₄O₇ + 0.1 M NaCl) solution has also been studied. The presence of these anions (except ) inhibits pitting corrosion. Chronoamperometry measurements showed that nucleation of pit takes place after an incubation time (t_i). The rate of pit nucleation () increases with increasing halide ions concentration and applied potentials, but decreases with increasing the concentration of the inorganic inhibitors (except ). The inhibition efficiency of these inhibitors decreases in the order:

     

Pitting and pitting control of Al in gluconic acid solutions - Polarization, chronoamperometry and morphological studies

The anodic behaviour of Al in gluconic acid (HG) solutions was studied. Al was found to pit in such solutions. Surface and cross-sectional views of the SEM images recorded beyond the breakdown potential (E_b) revealed the occurrence of intense pitting attack with the formation of large hemispherical pits. The effect of adding some environmentally acceptable inorganic inhibitors (tungstates, molybdates or silicates) on the pitting corrosion behaviour of Al in HG solutions was also studied. Measurements were carried out under the influence of various experimental variables based on polarization and chronoamperometric techniques. These measurements were complemented by ex situ scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) examinations of the electrode surface. The presence of these compounds in HG solutions decreased the passive current density (j_pass) and increased E_b. In HG solutions, chronoamperometric measurements showed that the anodic current density first decreased, due to growth of a passive oxide film, then increased with time after a pit incubation time, t_i and finally attained a steady-state value. Value of t_i was shortened and simultaneously the steady-state current was elevated, corresponding to an increase in the rate of pit initiation and growth, with increasing applied anodic potential and HG concentration. The rate of pit nucleation () was found to decrease to an extent depending on the type and concentration of the introduced inhibitor. The inhibitory effect of these compounds decreased in the order:  >  > .     

Complete protection of a passive film on iron from breakdown in a borate buffer containing 0.1 M of Cl by coverage with an ultrathin film of two-dimensional polymer

An ultrathin film of two-dimensional polymer was prepared on a passivated iron electrode by modification of a 16-hydroxyhexadecanoate ion self-assembled monolayer with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. This film prevented passive film breakdown examined by potentiodynamic anodic polarization of the coated electrode in the borate buffer solution containing 0.1 M of Cl⁻. Neither current spikes nor the pitting potential was observed in the passive and transpassive regions of polarization curve. The anodic current density was decreased in these regions markedly, implying hindrance to permeation of Cl⁻ and water through the film. Structure of the film was clarified by X-ray photoelectron and FTIR reflection spectroscopies and contact angle measurement with a drop of water. Electron-probe microanalysis of the passivated surface coated with the film after anodic polarization scanning up to the transpassive region revealed that the polymer film prevents pit initiation by an attack on the passive film with Cl⁻.     

Influence of anions on the formation of β-FeOOH rusts

The artificial β-FeOOH rusts were synthesized by oxidation of FeCl₂ solutions and hydrolysis of FeCl₃ solutions. Various Na salts such as sulfate, biphosphate, nitrate, and silicate were added to the starting solutions at different anion/Fe molar ratios of 0-0.05. The XRD patterns of the products showed only the diffraction peaks of β-FeOOH. The crystallinity of the products was noticeably reduced by adding and but slightly influenced by adding . The addition of markedly crystallized the products by the hydrolysis of FeCl₃. The N₂ adsorption revealed that the products with were porous particles assembled by β-FeOOH subcrystals. and strongly coordinating to Fe(III) markedly lowered the crystallinity of the products and remained in the formed particles.     

Inhibitive effect of diethylcarbamazine on the corrosion of mild steel in hydrochloric acid

Potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), weight loss measurements and atomic force microscopy techniques were used to investigate the inhibitory effect of diethylcarbamazine (DECM) on corrosion of mild steel in HCl solution. The inhibitor showed >90% inhibition efficiency at 5.01 × 10⁻⁴ M. Results obtained revealed that inhibition occurs through adsorption of inhibitor molecules on metal surface without modifying the mechanism of corrosion process. Potentiodynamic polarization studies suggested that it is a mixed type inhibitor, predominantly controls cathodic reaction. Activation parameters (E_a, ΔH and ΔS) and thermodynamic parameters (, and ) were calculated to investigate mechanism of inhibition.     

Corrosion inhibition of tin, indium and tin-indium alloys by adenine or adenosine in hydrochloric acid solution

The influence of the concentration of adenine (AD), adenosine (ADS) on the electrochemical corrosion behavior of tin, indium and tin-indium alloys in 0.5 M HCl solution at different temperatures was studied. The investigation involved potentiodynamic cathodic polarization and extrapolation of cathodic and anodic Tafel lines techniques. The inhibition efficiency (IE%) increases with an increase in the concentration of adenine or adenosine of all investigated electrodes. The inhibition process was attributed to the formation of adsorbed film on the surfaces of the electrodes that protects the surface against corrosive agent. The data exhibited that the inhibition efficiency slightly decreases with increasing temperature.Frumkin adsorption isotherm fits well the experimental data. The plots of ln K vs. 1/T in the presence of the two studied inhibitors showed linear behavior. The standard enthalpy, , entropy, and free energy changes of adsorption were evaluated; the calculated values of and were negative while those for were positive. Mainly, all the above results are suggestive of physisorption of the inhibitor molecules on the surfaces of the investigated electrodes.     

Inhibition of mild steel corrosion in acid solution by Pheniramine drug: Experimental and theoretical study

Inhibition of mild steel corrosion in 1 M HCl solution by Pheniramine drug was studied using weight loss, electrochemical impedance spectroscopy, linear polarization resistance, and potentiodynamic polarization measurements. The values of activation energy (E_a) and different thermodynamic parameters such as adsorption equilibrium constant (K_ads), free energy of adsorption , adsorption enthalpy and adsorption entropy were calculated and discussed. The adsorption process of studied drug on mild steel surface obeys the Langmuir adsorption isotherm. Potentiodynamic polarization measurements showed that Pheniramine is mixed-type inhibitor. Further, theoretical calculations were carried out and relations between computed parameters and experimental inhibition efficiency were discussed.     

Influence of 1,2-diaminoethane on the mechanism of aluminium corrosion in sulphuric acid solutions

The influence of 1,2-diaminoethane (DAE) on aluminium corrosion in H₂SO₄ solutions (pH 3) was investigated. In pure H₂SO₄, rapid uniform corrosion is followed by inhibition due to the formation of stable Al-sulphate binuclear bidentate metal bound surface complexes via a ligand exchange mechanism with two neighbouring sites. Metastable pitting is also observed. DAE acts as a strong corrosion inhibitor for both uniform and localised corrosion, due to the formation of Al-DAE monodentate hydrogen-bond surface complexes either by direct adsorption of the protonated molecule on Al-OH sites or via a ligand exchange mechanism with the proton of an site.     

Electrochemical studies of packed iron powder electrodes: Effects of common constituents of natural waters on corrosion potential

Using a powder disk electrode (PDE) made with micron-sized, high purity iron metal we investigated how the corrosion of this material is affected by solution conditions that are relevant to the degradation of contaminants in environmental remediation applications. Changes in corrosion potential (E_corr) with time showed that low pH, high concentrations of chloride, and natural organic matter led to breakdown of the passive film. Bicarbonate caused E_corr to decline rapidly into the active potential region, but then E_corr rose back into the passive region over 10s of hours. The rate of decline in E_corr was greatest at higher pHs, suggesting a specific effect of rather than a general effect of pH.     

Reaction model for kinetic of cobalt dissolution in carbonate/bicarbonate media

Cobalt dissolution in a carbonate/bicarbonate media was studied in order to elucidate the kinetic of the metal corrosion processes. Steady-state polarization and electrochemical impedance measurements were carried out during the active metal dissolution at different electrode rotation speeds. A reaction mechanism is presented in order to explain the metal dissolution: cobalt electrodissolution starts with the formation of intermediate (CoHCO₃)_ads on the electrode surface, followed by the simultaneous formation of a complex and the formation of a CoO film. Mass transport is characterised by diffusion of the complex away from the electrode. The reaction model was validated by an accurate simulation of the experimental steady-state polarisation and impedance measurements.     

Corrosion study of Alumina/Yttria-Stabilized Zirconia (Al2O3/YSZ) nanostructured Thermal Barrier Coatings (TBC) exposed to high temperature treatment

Thermal Barrier Coatings (TBC) of 8% Yttria-Stabilized Zirconia (8YSZ) were deposited on AISI-304 substrates via r.f magnetron sputtering. A buffer layer of alumina, Al₂O₃, was deposited to improve the adhesion of the YSZ monolayer to the substrate. The influence of the Al₂O₃/8YSZ coating on the electrochemical conductance evolution, , was examined by Electrochemical Impedance Spectroscopy measurements when the steels are exposed to temperatures of 700 and 500 °C for 2, 4, and 6 h. Results indicated that diminished three orders of magnitude, in samples coated with Al₂O₃/8YSZ with respect to uncoated steel.