PAN-H1.6Mn1.6O4锂离子筛膜的制备及在卤水中吸附性能

采用亲水的PAN为成膜材料,制备了掺杂H_1.6Mn_1.6O₄的PAN-H_1.6Mn_1.6O₄锂离子筛膜。通过SEM、Li⁺静态吸附实验、（NH₄）₂S₂O₈对锂的洗脱实验和卤水中吸附实验,研究了锂离子筛的添加量对PAN-H_1.6Mn_1.6O₄锂离子筛膜结构、Li⁺吸附-洗脱性能的影响。结果表明,PAN浓度为10%（质量）,H_1.6Mn_1.6O₄的添加量为50%（质量）时,PAN-H_1.6Mn_1.6O₄离子筛膜的吸附量为17.45 mg·g^-1,达到粉末状吸附量的88.0%。以（NH₄）₂S₂O₈为洗脱剂,当浓度为0.3 mol·L^-1、液固比为600:1、时间为12 h时,锂洗脱量为17.23 mg·g^-1,锰溶损率仅为1.14%。在含有Na⁺、K⁺、Mg²⁺和Ca²⁺的罗布泊老卤卤水中,锂离子筛膜对Li⁺有很高的选择性。在卤水中进行10次吸附与解吸循环,吸附量从11.64 mg·g^-1下降到10.94 mg·g^-1,吸附容量仅损失6.0%。总体结果表明亲水性载体对H_1.6Mn_1.6O₄吸附容量影响较小,温和的洗脱剂对锂离子筛膜的化学稳定性有利。     

离子筛吸附与陶瓷膜耦合用于盐湖卤水提锂

将锰系离子筛吸附与陶瓷膜耦合,用于高镁锂比盐湖卤水的提锂研究。采用水热法制备了高效锂离子筛H_1.6Mn_1.6O₄,考察离子筛用于卤水提锂效果和陶瓷膜的分离性能。结果表明：制备的离子筛粉体粒径分布在100～500 nm之间,平均粒径为160 nm,用于察尔汗盐湖卤水中对Li⁺吸附容量达到31.44 mg·g^-1;孔径50 nm的陶瓷膜对离子筛的截留率达到100%,膜渗透通量大于150 L·m^-2·h^-1;反冲操作可有效维持吸附-膜分离过程的稳定性,吸附与陶瓷膜的耦合过程对盐湖卤水中的锂提取率超过97%,盐酸和双氧水清洗可有效恢复膜渗透通量。研究结果为高镁锂比盐湖卤水提锂提供了新方法。     

Li1.6Mn1.6O4/PVDF多孔膜的制备及提锂性能

自制锂离子筛前驱体Li_1.6Mn_1.6O₄，并将Li_1.6Mn_1.6O₄粒子与高分子树脂PVDF杂化制膜，研究了膜经稀盐酸抽锂后对锂的吸附性能以及多次吸附与脱附性能等。结果表明，膜M-10-55[Li]采用0.5 mol·L^-1 HCl溶液抽锂约2 h锂的脱出基本达到平衡，Li⁺的洗脱率在95%左右，锰的溶损率为3.5%左右。抽锂后得M-10-55[H]对富锂溶液中锂的吸附约12 h达平衡，对锂的吸附容量较高为41 mg·g^-1，在第5次吸附时对锂的提取量为35 mg·g^-1左右。相比于Na⁺、K⁺、Mg²⁺、Ca²⁺，该膜对Li⁺表现出较好的选择性，对于从海水、盐湖卤水等液态锂资源中提取锂有很大的开发潜力。     

四元体系硼酸锂-硼酸钾-硼酸镁-水在308.15 K时固液相平衡研究

采用等温溶解平衡法研究四元体系硼酸锂-硼酸钾-硼酸镁-水在308.15 K时固液相平衡,测定了体系溶解度和平衡液相的密度、折光率和pH。研究发现：该体系308.15 K时的稳定相图中包含一个共饱点（L+Li₂B₄O₇·3H₂O+K₂B₄O₇·4H₂O+Mg₂B₆O₁₁·15H₂O）,其液相组成：w（Li₂B₄O₇）=3.112%、w（K₂B₄O₇）=16.64%、w（Mg₂B₆O₁₁）=0.101 8%;3个固相结晶区：Li₂B₄O₇·3H₂O、K₂B₄O₇·4H₂O、Mg₂B₆O₁₁·15H₂O,体系无复盐或固溶体生成。溶液中硼酸锂、硼酸钾对多水硼镁石有很强的盐析效应,液相的密度、折光率和pH随溶液中硼酸盐浓度的增加呈规律性变化。     

纳米片多面体锰基锂离子筛的制备及锂离子吸脱附特性

针对锰基锂离子筛容量发挥不充分、使用寿命短的问题,以电解二氧化锰、氯化锂及无水氯化铝为原料,采用水热法合成了铝原子掺杂锰基离子筛前驱体,经酸洗脱附锂离子后得到锰基锂离子筛H_1.6（Mn_1-x Al _x ）_1.6O₄。扫描电镜结果表明,铝原子掺杂后,样品呈均匀光滑的纳米片多面体形貌,进一步的吸脱附等温线分析显示,样品的比表面积显著提高。锂离子吸脱附特性研究结果表明,Li_1.6（Mn_0.7Al_0.3）_1.6O₄具有最佳的吸附提锂性能,锂离子溶液初始质量浓度为80 mg/L时,吸附容量为32.32 mg/L,5次循环提锂后,锂离子吸附容量可保持为初始吸附容量的95%。这些结果表明,结晶性好、比表面积大的纳米多面体锰基锂离子筛,吸附容量大、结构稳定性好,可为当前盐湖卤水中锂资源的开发和工艺优化提供技术参考。     

球形离子筛吸附剂的制备及其锂吸附性能评价

利用琼脂糖溶液的溶胶凝胶性质,通过锐孔凝固浴法,对实验室合成的Li₄Mn₅O₁₂粉体进行成型,制备了粒径2～3 mm的球形颗粒,对球形颗粒进行交联后,用1 mol·L^-1的盐酸对球形颗粒进行酸洗脱锂,最终制得球形锂离子筛吸附剂。考察球形吸附剂制备和交联的影响因素,结果表明：5%的琼脂糖浓度和90 ℃的温度为最佳制备条件,2 ml·g^-1的交联剂用量和6 h的交联时间为最佳交联条件。对球形离子筛吸附剂进行静态评价实验,结果表明锂吸附容量为4.25 mmol·g^-1,吸附速率为1.77×10^-5 s^-1,成型后离子筛吸附量是离子筛粉末的75.6%,吸附速率较粉体（3.29×10^-4 s^-1）下降一个数量级。Li⁺平衡吸附容量随平衡pH值的升高而增加,在pH>12时吸附容量高达5.5 mmol·g^-1。共存离子选择性实验表明,交联球形离子筛吸附剂对Li⁺具有高选择性,成型后离子筛可以用于盐湖卤水或者海水提锂。     

一步合成K、Cl共掺富锂锰基正极材料Li1.2Ni0.32Co0.04Mn0.44O2及其性能研究

以氢氧化物前驱体Ni_0.32Co_0.04Mn_0.44(OH)₂和LiOH·H₂O为原料，采用煅烧技术制备了单晶二次球形富锂锰基正极材料Li_1.2Ni_0.32Co_0.04Mn_0.44O₂;以KCl为烧结助剂和掺杂物，制备了不同KCl摩尔分数的富锂锰基正极材料Li_1.2-xK_xNi_0.32Co_0.04Mn_0.44O_2-xCl_x(x分别为0.01、0.02、0.03、0.04)。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线光电子能谱技术(XPS)、选择区域电子衍射(SEAD)、充放电测试、CV测试和EIS测试对材料结构和电化学性能进行表征，探究了不同氯化钾掺杂量对材料电化学性能的影响。结果表明，熔融的KCl不但...     

Li2ZrO3包覆LiNi0.8Co0.1Mn0.1O2的复合材料及其电化学性能

以Zr（NO₃）₄·5H₂O和CH₃COOLi·2H₂O为原料,采用湿化学法,将Li₂ZrO₃包覆在LiNi_0.8Co_0.1Mn_0.1O₂锂离子电池正极材料的表面,研究Li₂ZrO₃不同包覆比例对LiNi_0.8Co_0.1Mn_0.1O₂电化学性能的影响。SEM、TEM、EDS谱图分析表明,Li₂ZrO₃层均匀地包覆在LiNi_0.8Co_0.1Mn_0.1O₂表面,其厚度约为8 nm。与纯相相比,1%（质量分数） Li₂ZrO₃包覆的LiNi_0.8Co_0.1Mn_0.1O₂复合材料在1.0 C下首次放电比容量为184.7 mA·h·g^-1、100次循环之后放电比容量为169.5 mA·h·g^-1,其容量保持率达到91.77%,表现出良好的循环稳定性。循环伏安（CV）和电化学阻抗（EIS）测试结果表明,Li₂ZrO₃包覆层抑制了正极材料与电解液之间的副反应,减小了材料在循环过程中的电荷转移阻抗,从而提高了材料的电化学性能。     

四元体系（Li+， Mg2+//Cl-， borate-H2O）308.15 K相平衡与相图研究

采用等温溶解平衡法,开展四元体系Li⁺, Mg²⁺//Cl^-, borate–H₂O固液相平衡与相图研究,测定平衡溶液的液相组成、密度、折射率和pH。该四元体系相图中存在的盐类矿物为：LiCl·H₂O、Li₂B₄O₇·3H₂O、 MgCl₂·6H₂O、Mg₂B₆O₁₁·15H₂O和锂光卤石LiCl·MgCl₂·7H₂O,其中锂光卤石LiCl·MgCl₂·7H₂O是异成分复盐,溶液中MgCl₂存在下章氏硼镁石（MgB₄O₇·9H₂O）不稳定,转化为多水硼镁石（Mg₂B₆O₁₁·15H₂O）。多水硼镁石结晶区最大,表明镁硼酸盐易于结晶析出,而锂光卤石结晶区最小。采用Pitzer热力学模型对该四元体系的溶解度进行理论预测,计算相图与实验相图吻合较好。该四元体系的稳定相平衡与相图研究,可为含锂硼盐湖老卤中锂、镁、硼产品开发及其综合利用提供理论依据。     

258.15 K下五元体系Li+,Na+,Mg2+//SO42-,Cl--H2O相平衡研究

中国含锂盐湖大部分位于青藏、新疆等干旱少雨、冬季寒冷且漫长的地区。为指导低温提锂工艺的开发和设计、利用冬季冷能进行目标离子的富集及明确含锂盐湖在低温下的析盐规律,采用等温溶解平衡法对258.15 K、二水氯化钠饱和条件下的交互五元体系Li⁺,Na⁺,Mg²⁺∥SO₄^2-,Cl^--H₂O相平衡关系进行研究并构建等温平衡相图。结果表明,相图中有4个共饱点、6个两盐结晶区(NaCl·2H₂O+Na₂SO₄·10H₂O、NaCl·2H₂O+MgCl₂·8H₂O、NaCl·2H₂O+MgSO₄·7H₂O、NaCl·2H₂O+Li₂SO₄·H₂...     

Preparation and evaluation of α-Al2O3 supported lithium ion sieve membranes for Li+ extraction

Spinel lithium manganese oxide ion-sieves have been considered the most promising adsorbents to extract Li⁺ from brines and sea water. Here, we report a lithium ion-sieve which was successfully loaded onto tubular α-Al₂O₃ ceramic substrates by dipping crystallization and post-calcination method. The lithium manganese oxide Li₄Mn₅O₁₂ was first synthesized onto tubular α-Al₂O₃ ceramic substrates as the ion-sieve precursor (i.e. L-AA), and the corresponding lithium ion-sieve (i.e. H-AA) was obtained after acid pickling. The chemical and morphological properties of the ion-sieve were confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Both L-AA and H-AA showed characteristic peaks of α-Al₂O₃ and cubic phase Li₄Mn₅O₁₂, and the peaks representing cubic phase could still exist after pickling. The lithium manganese oxide Li₄Mn₅O₁₂ could be uniformly loaded not only on the surface of α-Al₂O₃ substrates but also inside the pores. Moreover, we found that the equilibrium adsorption capacity of H-AA was 22.9 mg·g^-1. After 12 h adsorption, the adsorption balance was reached. After 5 cycles of adsorption, the adsorption capacity of H-AA was 60.88% of the initial adsorption capacity. The process of H-AA adsorption for Li⁺ correlated with pseudo-second order kinetic model and Langmuir model. Adsorption thermodynamic parameters regarding enthalpy (ΔH), Gibbs free energy (ΔG) and entropy (ΔS) were calculated. For the dynamic adsorption- desorption process of H-AA, the H-AA exhibited excellent adsorption performance to Li⁺ with the Li⁺ dynamic adsorption capacity of 9.74 mg·g^-1 and the Mn²⁺ dissolution loss rate of 0.99%. After 3 dynamic adsorption-desorption cycles, 80% of the initial dynamic adsorption capacity was still kept.     

Preparation and characterization of lithium λ-MnO2 ion-sieves

Lithium λ-MnO₂ ion-sieves were prepared from spinel LiMn₂O₄ via treatment with nitric acid. The LiMn₂O₄ was synthesized by a solid state reaction between LiOH·H₂O and MnO₂. The effects of the calcination time and temperature on the preparation of the LiMn₂O₄ precursor and the lithium ion-sieve were investigated. In addition, the Li⁺ extraction ratio, the Mn²⁺ dissolving ratio and the adsorption properties of the lithium ion-sieve were all measured. The lithium ion-sieve had a high exchange capacity and was selective for Li⁺. Specifically, at pH= 13, the ion exchange capacity of Li⁺ was 30.9 mg/g in 10 mmol/L LiCl solution and the lithium extraction ratio and manganese dissolving ratio were 95% and 25%, respectively.     

负载型锂离子筛吸附剂研究进展

锂离子筛吸附剂能够经济地从卤水、海水中提取分离锂离子,然而锂离子筛吸附剂通常是细微的粉末材料,工业化应用时需要加工成型为填料,关键是得到吸附容量大和循环性能良好的锂离子筛吸附剂。现有的造粒和铸膜成型工艺导致锂离子筛吸附剂的吸附容量大幅降低,希望开发出不使用有机聚合物黏结剂的负载型锂离子筛吸附剂。综述了常用的几类锂离子筛吸附剂、载体材料和负载方法,总结了负载型锂离子筛吸附剂的技术要求,介绍了几种新的负载型锂离子筛吸附剂的制备方法。建议重点开发玻璃纤维材料负载的锂离子筛吸附剂H₄Ti₅O₁₂和氧化铝负载的锂离子筛吸附剂LiCl·2Al（OH）₃。     

KINEMATIC EVALUATION OF WET OXIDATION FOR PHENOLIC CONTAMINATED WATERS

Wet oxidations catalyzed by MnO₂, Co₂O₃, and CuSO₄.5H₂O, were carried out for waters containing 1000 mg/L phenol and 1500 mg/L p-chlorophenol, respectively. CuSO₄-5H₂O was demonstrated to be the most effective in reducing the concentration of phenols in waters. Rate constant and activation energy of the oxidation were also obtained, the enhancement of catalysts on the oxidation rate of phenol was found to be in increasing order of MnO₂, Co₂O₃, and CuSO₄-5H₂O. The cocurrent analyses of total organic carbon and high pressure liquid chromatography illustrated that the end products after oxidations, being intermediates within 10% extent in the liquid phase.