Enhanced electrochemical performance of straw-based porous carbon fibers for supercapacitor

The efficient utilization of natural biomass as renewable raw materials is of importance. We herein prepared porous carbon fibers (PCFs) by activation of the extracted cellulose microfibers from the agriculture byproduct of corn straw. Different from the porous carbons (PCs) by directly activating straw, the obtained PCFs had typical one-dimensional morphology with high surface area (2013 m² g^?1) and large pore volume (1.27 cm³ g^?1). The influence of the ZnCl₂/cellulose mass ratio on the electrochemical performance was studied, and the optimized PCF(1:1) possessed a much higher specific capacitance than the PC(1:1) sample, which was attributed to the improved specific surface area as well as the fiber-like morphology where it had short ion diffusion route and small interfacial resistance in comparison to PCs. PCFs have a high specific capacitance of 230 F g^?1 at 0.5 A g^?1, and 183 F g^?1 was retained at 20 A g^?1 (79.6%), revealing an excellent rate capability. The assembled symmetrical supercapacitor exhibited a wide potential window of 1.8 V, small electrochemical impedance, and superior cycle performance. Moreover, a high energy density of 16.0 Wh kg^?1 was obtained at a power density of 450.4 W kg^?1, which was preserved of 6.9 Wh kg^?1 at a high power density of 14,194.3 W kg^?1.     

Facile preparation of nitrogen-doped porous carbon for high performance symmetric supercapacitor

In this work, the micromolecule l-glutamic acid (Glu) is employed as nitrogen-rich precursor to prepare a novel porous carbon, and ZnCl₂ is used as activating agent to improve the surface area and electrochemical performance of the carbon. The nitrogen content of the carbon (Glu-2.5) prepared by Glu and ZnCl₂ with a mass ratio of 1:2.5 retains as high as 7.1 % at an activation temperature of 700 °C. The surface area and pore volume of Glu-2.5 are 1007.4 m² g^?1 and 0.57 cm³ g^?1, respectively. Glu-2.5 exhibits a high specific capacitance of 330.6 F g^?1 in 2 M KOH electrolyte at the current density of 1 A g^?1and good cycling stability (89 % retention of capacitance after 5000 charge/discharge cycles). More importantly, the assembled symmetric supercapacitor using Glu-2.5 as electrodes reveals a high energy density (16.7 Wh kg^?1) under the power density of 404.7 W kg^?1. Owing to its inherent advantages, Glu-2.5 could be a promising and scalable alternative applied to energy storage/conversion.     

Reed straw derived active carbon/graphene hybrids as sustainable high-performance electrodes for advanced supercapacitors

Reed straw-derived active carbon@graphene (AC@GR) hybrids were prepared by one-step carbonization/activation process using a mixture of reed straw and graphene oxide (GO) as raw materials and ZnCl₂ as activation agent. The as-prepared hybrids exhibit high specific surface area in a range of 1971–2497 m² g^?1, abundant porosity, as well as excellent energy storage capability. The symmetric C//C supercapacitor using the hybrid obtained at 700 °C as electrodes demonstrates superior cycling durability, ca. 90 % retention after 6000 cycles at 2 A g^?1, and a high energy density of 6.12 Wh kg^?1 at a power density of up to 4660 W kg^?1 in 6 M KOH aqueous electrolyte. The excellent capacitive performance is attributed to the synergistic effect of AC and GR.     

Electrospun porous MnMoO<Subscript>4</Subscript> nanotubes as high-performance electrodes for asymmetric supercapacitors

MnMoO₄ nanotubes of diameter about 120 nm were successfully synthesized by a single-spinneret electrospinning technique followed by calcination in air, and their structural, morphological, and electrochemical properties were studied with the aim to fabricate high-performance supercapacitor devices. The obtained MnMoO₄ nanotubes display a 1D architecture with a porous structure and hollow interiors. Benefiting from intriguing structural features, the unique MnMoO₄ nanotube electrodes exhibit a high specific capacitance, excellent rate capability, and cycling stability. As an example, the tube-like MnMoO₄ delivers a specific capacitance of 620 F g^?1 at a current density of 1 A g^?1, and 460 F g^?1 even at a very high current density of 60 A g^?1. Remarkably, almost no decay in specific capacitance is found after continuous charge/discharge cycling for 10,000 cycles at 1 A g^?1. An asymmetric supercapacitor fabricated from this MnMoO₄ nanotubes and activated carbon displayed a maximum high energy density of 31.7 Wh kg^?1 and a power density of 797 W kg^?1, demonstrating a good prospect for practical applications in energy storage electronics.     

Dual template method to prepare hierarchical porous carbon nanofibers for high-power supercapacitors

Hierarchical porous carbon nanofibers serving as electrode materials are prepared through carbonization and hydrofluoric acid treatment of polyacrylonitrile-based electrospinning involving dual templates. The hierarchical porous structures are synergistically tailored by varying template contents in the spinning solution. The carbon nanofibers prepared from the electrospinning of polyacrylonitrile containing 15/15 wt.% polymethylmethacrylate/tetraethyl orthosilicate exhibit the largest specific surface area (699 m² g^?1) and microporous volume (0.196 cm³ g^?1). In 6 M KOH electrolyte, a symmetrical supercapacitor equipped with the hierarchical porous carbon nanofibers demonstrates its high-end specific capacitance of 170 F g^?1, superior rate capability, and high-power density output up to 14.7 kW kg^?1. Cycling evolution indicates capacitance fading is only 5.8 % of initial capacitance at a current density of 1 A g^?1 even after 8,000 cycles. The excellent electrochemical performances of the carbon nanofiber are mainly ascribed to the optimized pore size distributions of both micropores and mesopores and the unique hierarchical pore structures possessed by abundant micropores.     

Binder-free activated carbon papers for high-performance electric double-layer capacitors

A binder-free activated carbon paper (ACP) was simply prepared for electric double-layer capacitors by the carbonization of filter paper, followed by heat-air activation at a lower temperature. The electrochemical cells assembled using the as-prepared ACP-470 provides a high specific capacitance of 296.4 F g^?1 at current density of 0.5 A g^?1 and a high rate performance at a current density of 150 A g^?1 with a capacitance of 191.2 F g^?1 and a high cycle ability at 10,000 recycles with 100 % capacitance retention. In addition, the ACP has a lower electrical resistivity and provides an effective energy storage performance with a maximum energy density of 41.2 Wh kg^?1 and a maximum power density of 138.0 kW kg^?1 in a voltage range of 1 V.     

KOH‐Activated Porous Carbons Derived from Chestnut Shell with Superior Capacitive Performance

Porous carbons (PC) were prepared from a waste biomass named chestnut shell via a two‐step method involving carbonization and KOH activation. The morphology, pore structure and surface chemical properties were investigated by scanning electron microscopy (SEM), N₂ sorption, Raman spectroscopy, X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS). The carbons have been evaluated as the electrode materials for supercapacitors by a two‐electrode system in 6 mol/L KOH electrolyte. Benefiting from the porous texture, high surface area and high oxygen content, the PCs derived from chestnut shell have exhibited high specific capacitance of 198.2 (PC‐1), 217.2 (PC‐2) and 238.2 F·g^?1 (PC‐3) at a current density of 0.1 A·g^?1, good rate capability of 55.7%, 56.6% and 54.9% in a range of 0.1–20 A·g^?1 and high energy density of 5.6, 6.1 and 6.7 Wh·kg^?1, respectively. This is believed to be due to electric double layer capacitance induced by the abundant micropores and extra pseudo‐capacitance generated by oxygen‐containing groups. At a power density of 9000 Wh·kg^?1, the energy density is 3.1, 3.5 and 3.7 Wh·kg^?1 for PC‐1, PC‐2 and PC‐3, respectively, demonstrating the potential of the carbons derived from chestnut shells in energy storage devices.     

A tunable hierarchical porous carbon from starch pretreated by calcium acetate for high performance supercapacitors

Hierarchical porous carbons (HPCs) with abundant mesopores have been prepared by a facile route from the starch that was pretreated by calcium acetate. The scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and N₂ adsorption–desorption tests show that hierarchical porous carbons with bimodal mesopores have been obtained. Moreover, the pore sizes are tunable by simply adjusting the reactants ratio and carbonization temperature. The as-synthesized hierarchical porous carbon materials (HPCs-2-800) possesses the highest Brunauer-Emmett-Teller (BET)-specific surface area of 464 m² g^?1 and mesoporous volume of 0.663 cm³ g^?1 at the carbonization temperature of 800 °C and starch to calcium acetate mass ratio of 2. Electrochemical measurements also display that the HPCs-2-800 electrodes have a high reversible capacity of 244 F g^?1 at the current density of 0.1 A g^?1 and 182 F g^?1 at the current density of 10 A g^?1. When the current density is elevated from 0.1 to 10 A g^?1, the high capacitance retention of 74.6 % reveals a good rate performance. Long charge–discharge cycling measurements disclose good stabilities over 25,000 cycles at different current densities of 1–10 A g^?1 (5000 cycles at each current density) for HPCs-2-800 electrode. The cycling results indicate a high capacitance retention of 99.6 % over 5000 charge–discharge cycles even at the current density of 10 A g^?1. The excellent supercapacitive performances imply that HPCs-2-800 is a promising candidate for supercapacitors.     

Facile fabrication of mesoporous manganese oxides as advanced electrode materials for supercapacitors

Mesoporous manganese oxides (MnO₂) were synthesized via a facile chemical deposition strategy. Three kinds of basic precipitants including sodium carbonate (Na₂CO₃), sodium bicarbonate (NaHCO₃), and sodium hydroxide (NaOH) were employed to adjust the microstructures and surface morphologies of MnO₂ materials. The obtained MnO₂ materials display different microstructures. Great differences are observed in their specific surface area and porosity properties. The microstructures and surface morphologies characteristics of MnO₂ materials largely determine their pseudocapacitive behavior for supercapacitors. The MnO₂ prepared with Na₂CO₃ precipitant exhibits the optimal microstructures and surface morphologies compared with the other two samples, contributing to their best electrochemical performances for supercapacitors when conducted either in the single electrode tests or in the capacitor measurements. The optimal MnO₂ electrode exhibits a high specific capacitance (173 F g^–1 at 0.25 A g^?1), high-rate capability (123 F g^?1 at 4 A g^?1), and excellent cyclic stability (no capacitance loss after 5,000 cycles at 1 A g^?1). The optimal activated carbon//MnO₂ hybrid capacitor exhibits a wide working voltage (1.8 V), high-power and high-energy densities (1,734 W kg^?1 and 20.9 Wh kg^?1), and excellent cycling behavior (93.8 % capacitance retention after 10,000 cycles at 1 A g^?1), indicating the promising applications of the easily fabricated mesoporous MnO₂ for supercapacitors.     

Facile synthesis of biomass-derived hierarchical porous carbon microbeads for supercapacitors

Using the facile method of solvent evaporation, the leonardite fulvic acids (LFA)-based porous carbon microbeads (PCM) have been successfully prepared at ambient pressure, followed by carbonization and KOH activation (a low mass ratio alkali/LFA = 1.5) in an inert atmosphere. The effects of KOH treatment on pore structures and the formation mechanism of the PCM were discussed. The results showed that the sample exhibited remarkable improvement in textural properties. The activated carbon microbeads had high surface area (2269 m² g^?1), large pore volume (1.97 cm³ g^?1), and displayed excellent capacitive performances, compared with carbon powder. The porous carbon material electrodes with the “porous core structure” behaved superiorly at a specific capacitance of 320 F g^?1 at a current density of 0.05 A g^?1 in 6 M KOH electrolyte, which could still remain 193 F g^?1 when the current density increased to 100 A g^?1. Remarkably, in the 1 M TEABF₄/PC electrolyte, the PCM samples could reach 156 F g^?1 at 0.05 A g^?1, possess an outstanding energy density of 39.50 Wh kg^?1, and maintain at 22.05 Wh kg^?1 even when the power density rose up to 5880 W kg^?1. The balance of structural characteristic and high performance makes the porous carbon microbeads a competitive and promising supercapacitor electrode material.     

A high mass loading electrode based on ultrathin Co<Subscript>3</Subscript>S<Subscript>4</Subscript> nanosheets for high performance supercapacitor

There is a growing need for the electrode with high mass loading of active materials, where both high energy and high power densities are required, in current and near-future applications of supercapacitor. Here, an ultrathin Co₃S₄ nanosheet decorated electrode (denoted as Co₃S₄/NF) with mass loading of 6 mg cm^?2 is successfully fabricated by using highly dispersive Co₃O₄ nanowires on Ni foam (NF) as template. The nanosheets contained lots of about 3～5 nm micropores benefiting for the electrochemical reaction and assembled into a three-dimensional, honeycomb-like network with 0.5～1 μm mesopore structure for promoting specific surface area of electrode. The improved electrochemical performance was achieved, including an excellent cycliability of 10,000 cycles at 10 A g^?1 and large specific capacitances of 2415 and 1152 F g^?1 at 1 and 20 A g^?1, respectively. Impressively, the asymmetric supercapacitor assembled with the activated carbon (AC) and Co₃S₄/NF electrode exhibits a high energy density of 79 Wh kg^?1 at a power density of 151 W kg^?1, a high power density of 3000 W kg^?1 at energy density of 30 Wh kg^?1 and 73 % retention of the initial capacitance after 10,000 charge-discharge cycles at 2 A g^?1. More importantly, the formation process of the ultrathin Co₃S₄ nanosheets upon reaction time is investigated, which is benefited from the gradual infiltration of sulfide ions and the template function of ultrafine Co₃O₄ nanowires in the anion-exchange reaction.

Open image in new window

Graphical abstract The ultrathin 2D Co₃S₄ nanosheets fabricated on 3D Ni foam and the formation process of the ultrathin Co₃S₄ nanosheets upon reaction times has been investigated. At the same time, the Co₃S₄/NF electrode displays an outstanding specific capacitance of 2420 F g^?1 at 1 A g^?1 with high mass loading of 6 mg cm^?2.

     

硼、氮共掺杂多孔碳的制备及其超电容性能

分别以含氮菲咯啉、四硼酸钾和醋酸锌为碳源、活化剂和模板,制备了B、N共掺杂多孔碳(BN-PC),并探究模板质量对BN-PC结构和储电性能的影响。当醋酸锌质量为5g时,所得BN-PC₅中B、N杂原子含量分别为 20.21%、18.29%。电化学测试结果表明,以6 mol·L^-1 KOH为电解液,BN-PC₅电极展现出高的比电容(在0.05 A·g^-1电流密度下为255 F·g^-1)、优异的倍率性能(在20A·g^-1电流密度下为188F·g^-1)和卓越的循环稳定性(在5 A·g^-1的电流密度下循环10 000次比电容保持率为97%)。以3 mol·L^-1 ZnSO₄为电解液,在平均功率密度为56W·kg^-1时,BN-PC₅电容器的能量密度可达27Wh·kg^-1。     

Synthesis of micro- and mesoporous carbon spheres for supercapacitor electrode

Micro- and mesoporous carbon spheres (MMCSs) are synthesized by the polymerization of colloidal silica-entrapped resorcinol/formaldehyde in the presence of ammonia as catalyst, followed by carbonization, sodium hydroxide (NaOH) etching to remove silica template, and potassium hydroxide (KOH) activation. The morphology and microstructure are characterized by scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption–desorption. The results show that a typical sample (denoted as MMCS-3) unites the characteristics of regular spherical shape (uniform diameters of 500 nm), high specific surface area (1,620 m² g^?1), large pore volume (1.037 cm³ g^?1), and combined micropores and mesopores (11.0 nm), which endows MMCS-3 good electrochemical performance. MMCS-3 as supercapacitor electrode shows a specific capacitance of 314 F g^?1 under a current density of 0.5 A g^?1 and low internal resistance of 0.2 Ω in 6 M KOH aqueous solution. The electrochemical capacitance still retains 198 F g^?1 at a high current density of 10 A g^?1. After 500 cycle numbers of galvanostatic charge/discharge at 0.5 A g^?1, MMCS-3 electrode still remains the specific capacitance of 301 F g^?1 with the retention of 96 %. This study highlights the potential of well-designed MMCSs as electrodes for widespread supercapacitor applications.     

Design of high-performance core-shell hollow carbon nanofiber@nickel-cobalt double hydroxide composites for supercapacitive energy storage

The supercapacitive performances of supercapacitor mainly depend on the physical nanostructure and micro-morphology of electrode materials. Here, we demonstrated the design, synthesis and electrochemical performances of core-shell hollow carbon nanofiber@nickel-cobalt-layered double hydroxide (HCNF@ Ni_0.67Co_0.33-LDH) nanocomposites with an optimized Ni/Co molar ratio of 2:1. The HCNF was used as superiorly conductive core to sustain the nanoporous silky Ni_0.67Co_0.33-LDH shell, which can efficiently provide fast transport pathways for electrons and electrolyte ions. The outstanding specific capacitance of 2486 F g^?1 at 1 A g^?1 based on galvanostatic charge-discharge curves were acquired for the highly electroactive HCNF@Ni_0.67Co_0.33-LDH. Furthermore, the HCNF@Ni_0.67Co_0.33-LDH electrode delivered a distinguished rate capability with a specific capacitance of 1890 F g^?1 even at 15 A g^?1. Notably, an asymmetric supercapacitor with HCNF@Ni_0.67Co_0.33-LDH as cathode and HCNF as anode was devised, which presented a prominent specific capacitance of 228 F g^?1, good energy density of 62.1 Wh kg^?1, and impressive cycling stability (90.6% capacitance retention after 10,000 cycles).     

In situ synthesis of crosslinked-polyaniline nano-pillar arrays/reduced graphene oxide nanocomposites for supercapacitors

Crosslinked-polyaniline (CPA) nano-pillar arrays adsorbed on the surface of reduced graphene oxide (RGO) sheets were synthesized by in situ solution polymerization through two steps of reduction. The electrochemical analyses demonstrated that the befittingly reduced CPA/RGO composite exhibited high performance as electrode materials for supercapacitors. The CPA/RGO composite showed very high specific capacitance of 1532 F g^?1 at a scan rate of 10 mV s^?1 or 694 F g^?1 at a current density of 2 A g^?1 in 1 M H₂SO₄ electrolyte, as well as great energy density of 61.4 W h kg^?1 at a current density of 2 A g^?1. The electrode material also had decent power density of 4 kW kg^?1 at a current density of 10 A g^?1, and good cycling stability of 92.5 % capacitance retained after 500 cycles of cyclic voltammetry at 500 mV s^?1. The neat microstructures and super electrochemical properties suggest the potential use of the composites in supercapacitors.     

Converting eucalyptus leaves into mesoporous carbon for its application in quasi solid-state supercapacitors

A high performance activated carbon having pore diameter of 2.8 nm and specific surface area of 841.8 m² g^?1 is prepared by chemical activation of eucalyptus leaves using KOH as an activating agent. The chemically-treated eucalyptus leaves EL(T) as electrode material has a specific capacitance of 663.5 mF cm^?2 (equivalent to single electrode specific capacitance of 442.3 F g^?1) with solid polymer electrolyte. This active material has excellent rate capability and good cycle performance, over 95 % of the original capacitance is retained after 5,000 cycles. The energy density of 101.6 Wh kg^?1 and power density of 2.85 kW kg^?1 has been observed for EL(T) based quasi solid-state supercapacitors.     

Nanostructured ferrite/graphene/polyaniline using for supercapacitor to enhance the capacitive behavior

Graphene nanosheets, polyaniline (PANI), and nanocrystallites of transition metal ferrite {Fe₃O₄ (Mag), NiFe₂O₄ (NiF), and CoFe₂O₄ (CoF)} have been prepared and characterized via XRD, FTIR, SEM, TEM, UV–vis spectroscopy, cyclic voltammetry, galvanostatic charge discharges, and impedance spectroscopy. Electrochemical measurements showed that supercapacitances of hybrid electrodes made of the ternary materials are higher than that of hybrid electrode made of binary or single material. The ternary hybrid CoF/graphene (G)/PANI electrode exhibits a highest specific capacitance reaching 1123 Fg^?1, an energy density of 240 Wh kg^?1 at 1 A g^?1, and a power density of 2680 Wkg^?1 at 1 A g^?1 and outstanding cycling performance, with 98.2% capacitance retained over 2000 cycles. The extraordinary electrochemical performance of the ternary CoF/G/PANI hybrid can be attributed to the synergistic effects of the individual components. The PANI conducting polymer enhances an electron transport. The Ferrite nanoparticles prevent the restocking of the carbon sheets and provide Faradaic processes to increase the total capacitance.     

Preparation,characterization, and evaluation of LiNi0.4Co0.6O2 nanofibers for supercapacitor applications

We prepared LiNi_0.4Co_0.6O₂ nanofibers by electrospinning at the calcination temperature of 450 °C for 6 h. The prepared LiNi_0.4Co_0.6O₂ nanofibers was characterized by thermal, X-ray diffraction, and Fourier transform infrared (FTIR) studies. The morphology of LiNi_0.4Co_0.6O₂ nanofibers was characterized by scanning electron microscopy studies. The asymmetric supercapacitor was fabricated using LiNi_0.4Co_0.6O₂ nanofibers as positive electrode and activated carbon (AC) as negative electrode and a porous polypropylene separator in 1 M LiPF₆–ethylene carbonate/dimethyl carbonate (LiPF₆–EC:DMC) (1:1?v/v) as electrolyte. Cyclic voltammetry studies were then carried out in the potential range of 0 to 3.0 V at different scan rates which exhibited the highest specific capacitance of 72.9 F g^?1. The electrochemical impedance measurements were carried out to find the charge transfer resistance and specific capacitance of the cell, and they were found to be 5.05 Ω and 67.4 F g^?1, respectively. Finally, the charge–discharge studies were carried out at a current density of 1 mA cm^?2 to find out the discharge-specific capacitance, energy density, and power density of the capacitor cell, and they were found to be 70.9 F g^?1, 180.2 Wh kg^?1, and 248.0 W kg^?1, respectively.     

The production of activated carbon from cation exchange resin for high-performance supercapacitor

High-performance activated carbon for electrochemical double-layer capacitors (EDLC) has been prepared from cation exchange resin by carbonization and subsequent activation with KOH. The activation temperature has a key role in the determination of porous carbon possessing high surface areas, and large pore structures. The porous carbon activated at 700 °C (carbon-700-1:4) has high surface area (2236 m²?g^?1) and large total pore volume (1.15 cm³?g^?1), which also displays best capacitive performances due to its well-balanced micro- or mesoporosity distribution. In details, specific capacitances of the carbon-700-1:4 sample are 336.5 F?g^?1 at a current density of 1 A?g^?1 and 331.8 F?g^?1 at 2 A?g^?1. At high current density as 20 A?g^?1, the retention of its specific capacitance is 68.4 %. The carbon-700-1:4 sample also exhibits high performance of energy density (46.7 Wh?kg^?1) and long cycle stability (～8.9 % loss after 3,000 cycles). More importantly, due to the amount of waste ion-exchange resins increasing all over the world, the present synthetic method might be adopted to dispose them, producing high-performance porous carbons for EDLC electrode materials.     

Excellent electrochemical performance of nitrogen-enriched hierarchical porous carbon electrodes prepared using nano-CaCO3 as template

Recently, tremendous research efforts have been concentrated on developing high-performance electrode materials to meet the ever-increasing energy and power demands in supercapacitors. Herein, we presented a high-capacity supercapacitor material based on nitrogen-enriched hierarchical porous carbons (NHPCs) synthesized by the carbonization of melamine formaldehyde resins using eco-friendly and inexpensive nano-CaCO₃ as template. The effects of carbonization temperature and template content on the porous structure and electrochemical characteristics were compared and discussed in detail. The prepared NHPCs possessed large surface area up to 834 m² g^?1 and high nitrogen content up to 20.94 wt %. As electrode material for supercapacitors, NHPCs exhibited superior electrochemical performances with high specific capacitance (190 F g^?1 at 20 A g^?1), outstanding rate capability (80 %), and excellent cycling stability (over 2,000 cycles at 5 A g^?1) in 1 M sulfuric acid media. The excellent electrochemical performances are due to the synergic effects of unique hierarchical porous microstructure, abundant nitrogen and oxygen functionalities, as well as high degree of graphitization framework.