Electrochemical characterization of single-walled carbon nanotubes for electrochemical double layer capacitors using non-aqueous electrolyte

Single-walled carbon nanotubes (SWCNTs) were investigated by cyclic voltammetry and electrochemical impedance spectroscopy in a non-aqueous electrolyte, 1 M Et₄NBF₄ in acetonitrile, suitable for supercapacitors. Further, in situ dilatometry and in situ conductance measurements were performed on single electrodes and the results compared to an activated carbon, YP17. Both materials show capacitive behavior characteristic of high surface area electrodes for supercapacitors, with the maximum full cell gravimetric capacitance being 34 F/g for YP17 and 20 F/g for SWCNTs at 2.5 V with respect to the total active electrode mass. The electronic resistance of SWCNTs and activated carbon decreases significantly during charging, showing similarities of the two materials during electrochemical doping. The SWCNT electrode expands irreversibly during the first electrochemical potential sweep as verified by in situ dilatometry, indicative of at least partial debundling of the SWCNTs. A reversible periodic swelling and shrinking during cycling is observed for both materials, with the magnitude of expansion depending on the type of ions forming the double layer.     

Microwave-electrochemical formation of colloidal zinc oxide at fluorine doped tin oxide electrodes

Colloidal ZnO is obtained during microwave-enhanced electrochemical deposition experiments from an aqueous solution containing 0.1 M Zn(NO₃)₂ and 0.02 M H₂O₂ via repetitive negative going potential cycles from 0.3 to −0.8 V vs. SCE. The effects of temperature and temperature gradients on ZnO electro-formation at fluorine doped tin oxide (FTO) electrodes are investigated with both a conventional thermostated bath system (isothermal) and an in situ microwave electrochemistry system (non-isothermal). Mainly electrodeposition of ZnO is observed in uniformly heated stagnant solution and predominantly the electro-formation of ZnO colloid is observed in the presence of microwave-induced temperature gradients in a flowing solution. For the ZnO colloid prepared via microwave activation, SAXS data suggests an average particle radius of ca. 18 nm. The increase of ZnO nanoparticle concentration during repetitive potential scans is followed by photoluminescence spectroscopy. A possible mechanism for ZnO colloid formation during electrochemical reduction of H₂O₂ is suggested.     

Kinetics of the electrochemical oxidation of 2-nitrophenol and 4-nitrophenol studied by in situ UV spectroscopy and chemometrics

Here we report on the elimination of 4-nitrophenol (4-NPh) and 2-nitrophenol (2-NPh) from aqueous solutions by electrochemical oxidation at the dimensionally stable anodes (DSA) Ti/IrO₂-SnO₂-Sb₂O₅. The ternary oxide electrodes show high catalytic activity for the electrochemical oxidation of nitrophenolic compounds. UV-vis spectroscopy was employed to in situ monitor time-dependent concentration changes during the electrochemical oxidation of the 2-NPh and 4-NPh. A kinetic analysis of the electrochemical oxidation of 2-NPh, 4-NPh and a mixture of the two has been carried out. The electrochemical oxidation of 4-NPh and 2-NPh is governed by the hydroxyl radical reaction and obeys the first-order kinetics with the overall apparent activation energy of 8.3 and 9.2 kJ mol⁻¹, respectively. Partial least squares (PLS) regression was performed to resolve the highly overlapping spectrophotometric signals measured from the mixture of 4-NPh and 2-NPh. In situ UV-vis spectroscopic measurements in combination with PLS multivariate calibration enabled us to determine the competitive effects during the electrochemical treatment of variety of mixtures of 2-NPh and 4-NPh, showing that the presence of 2-NPh inhibits the electrochemical oxidation of 4-NPh.     

Hydrogen oxidation kinetics on model Pd/C electrodes: Electrochemical impedance spectroscopy and rotating disk electrode study

This work reports on the kinetics of the hydrogen oxidation reaction (HOR) on model Pd nanoparticles supported on a low surface area carbon substrate. Two Pd/C samples, with the average particle size 2.6 and 4.0 nm were used. The structure of the catalysts was characterized with the ex situ (electron microscopy) and in situ (electrochemical) methods. We utilized the electrochemical impedance spectroscopy (EIS) and the rotating disk electrode (RDE) voltammetry to study the kinetics of the HOR on Pd/C. The relevance of these techniques for elucidating the kinetics and the mechanism of the HOR on Pd/C was explored. The experimental results suggest that the catalytic activity of Pd in the HOR is more than 2 orders of magnitude lower than that of Pt, and does not depend on the particle size in the range from 2.6 to 4.0 nm. Computational modeling of the experimental steady-state (RDE) and non-steady-state (EIS) data shows that the reaction kinetics can be adequately described within Heyrovsky-Volmer mechanism, with the rate constants υ_0H = (8.8 ± 1.5) × 10⁻¹⁰ mol cm⁻² s⁻¹ and υ_0V = (1.0 ± 0.3) × 10⁻⁸ mol cm⁻² s⁻¹. The model suggests that underpotentially deposited hydrogen H_UPD is unlikely to be the active intermediate H_ad of the HOR. It is concluded that the surface coverage of H_ad deviates from that of H_UPD with increasing overpotential, and the lateral interactions within H_ad adlayer are weak.     

A carbon in molten carbonate anode model for a direct carbon fuel cell

The electrochemical oxidation of carbon at the anode of a direct carbon fuel cell (DCFC) includes charge transfer steps and chemical steps. A microstructural model of carbon particle is built, in which perfect graphene stacks are taken as the basic building blocks of carbon. A modified mechanism taking account of the irreversibility of the process and supposing that the electrochemical oxidation of carbon takes place only at the edges of the graphene sheets is proposed. A Tafel type overall rate equation is deduced along with expressions of exchange current density (j₀) and activation polarization (η_act). The performance of carbon black and graphite as the fuel of DCFC is examined. It has been found that j₀ is in the range of 0.10-6.12 mA cm⁻² at 923-1123 K and η_act is in the range of 0.024-0.28 V at 923-1123 K with current density in 10-120 mA cm⁻². Analysis of the j₀, η_act values and the product composition reveals that the charge transfer steps as well as the oxygen ion absorption steps are both important for the reaction rate. The activity of the carbon material with respect to atom location is introduced to the open circuit potential difference (OCP) calculation with Nernst equation.     

In situ generation of diazonium cations in organic electrolyte for electrochemical modification of electrode surface

The modification of glassy carbon electrode was achieved by electrochemical reduction of in situ generated diazonium cations in acetonitrile. The in situ generation of 4-nitrophenyl diazonium cations in acetonitrile was investigated by spectroscopic methods. UV-visible spectroscopy revealed slow kinetics for the reaction of 4-nitroaniline with tert-butylnitrite in acetonitrile to form the corresponding diazonium cation. As a result, a coupling reaction, which implies a consumption of the amine and loss of the already formed diazonium cations, was evidenced by ¹H NMR spectroscopy. This spectroscopic study allowed the optimization of the in situ diazonium cations generation prior to the modification step. The electrochemical modification of the carbon electrodes with 4-nitrophenyl, 4-bromophenyl and anthraquinone groups was characterized by cyclic voltammetry and the resulting grafted layer were characterized by electrochemical techniques. The cyclic voltammetric behaviour during the electrochemical grafting was very similar to the one observed for an isolated diazonium salt dissolved in acetonitrile. In the case of the anthraquinone-modified electrode, the use of acetonitrile, into which the corresponding amine is soluble but not in aqueous media, allowed for its grafting by the in situ approach. The barrier properties of these grafted layers are similar to those obtained from isolated diazonium salts. Finally, the chemical composition of the grafted layers was determined by X-ray photoelectron spectroscopy and surface coverage in the range 5-7 × 10⁻¹⁰ mol cm⁻² was estimated for films grown in our experimental conditions.     

Dimethoxymethane electrooxidation on low index planes of platinum single crystal in acid media

Conventional electrochemical methods have been applied to study the oxidation of a possible alternative fuel for a direct oxidation fuel cell. The electrooxidation of dimethoxymethane (DMM) was investigated on the three low index planes, (1 0 0), (1 1 0) and (1 1 1) of platinum single crystals and compared with its oxidation on a platinum polycrystalline electrode. Among platinum electrodes, electroreactivity of DMM observed is Pt(1 1 1) > Pt(1 0 0) > Pt(1 1 0) ∼ Pt poly. Hydrogen adsorption is limited by the presence of DMM, except for Pt(1 1 1) plane. In situ IR experiments show the presence of bands of CO_ads with all electrodes except Pt(1 1 1). This work shows that the mechanism of DMM electrooxidation is structure sensitive. A path takes place on Pt(1 0 0) and Pt(1 1 0) which is favourable to the formation of CO_ads. Another path proceeds on Pt(1 1 1), where CO_ads is not present and reaction does not occur at low potential. Results indicate that peak intensities are higher in perchloric acid than in sulphuric acid. So DMM adsorption is dependent on the specific adsorption of the anions. In situ IR reflectance spectroscopy identified some intermediates and reaction products of DMM adsorption and electrooxidation on Pt electrodes: CO_L (linearly bonded) and CO_B (bridge bonded), adsorbed CHO and CH₃O species, methanol and CO₂. The electrochemical and spectroelectrochemical experiments suggest a complex mechanism of DMM electrooxidation.     

Electrochemical determination of bromide at a multiwall carbon nanotubes-chitosan modified electrode

A multiwall carbon nanotubes (MWNTs)-chitosan modified glassy carbon electrode (GCE) exhibits attractive ability for highly sensitive cathodic stripping voltammetric measurements of bromide (Br⁻). In pH 1.8 H₂SO₄ solution, a substantial increase in the stripping peak current of Br⁻ (compared to bare GCE and chitosan modified GCE) is observed using MWNTs-chitosan modified electrode. Operational parameters were optimized and the electrochemical behaviors of Br⁻ were studied by different electrochemical methods. The kinetics parameters were measured, the number of electron transfer (n) was 1 and the transfer coefficient (α) is 0.17. A wide linear calibration range (3.6 × 10⁻⁷-1.4 × 10⁻⁵ g mL⁻¹) was achieved, with a detection limit of 9.6 × 10⁻⁸ g mL⁻¹. The mechanism of electrode reaction was fully discussed.     

Corrosion inhibition of mild steel by alkylimidazolium ionic liquids in hydrochloric acid

The acid corrosion inhibition process of mild steel in 1 M HCl by 1-butyl-3-methylimidazolium chlorides (BMIC) and 1-butyl-3-methylimidazolium hydrogen sulfate ([BMIM]HSO₄) has been investigated using electrochemical impedance, potentiodynamic polarization and weight loss measurements. Potentiodynamic polarization studies indicate the studied inhibitors are mixed type inhibitors. For both inhibitors, the inhibition efficiency increased with increase in the concentration of the inhibitor and the effectiveness of the two inhibitors are in the order [BMIM]HSO₄ > BMIC. The adsorption of the inhibitors on mild steel surface obeyed the Langmuir's adsorption isotherm. The effect of temperature on the corrosion behavior in the presence of 5 × 10⁻³ M of inhibitors was studied in the temperature range of 303-333 K. The associated activation energy of corrosion and other thermodynamic parameters such as enthalpy of activation (ΔH), entropy of activation (ΔS), adsorption equilibrium constant (K_ads) and standard free energy of adsorption (ΔG_ads) were calculated to elaborate the mechanism of corrosion inhibition.     

Activated carbon nanotubes-supported catalyst in fuel cells

The electrochemical property of platinum loaded on activated carbon nanotubes (Pt/ACNTs) was investigated by cyclic voltammograms (CVs) recorded in H₂SO₄ and H₂SO₄/CH₃OH aqueous solutions, respectively. Compared to 0.0046 A/cm² of Pt-loaded on pristine carbon nanotubes (Pt/CNTs) with a S_BET of 164 m²/g and 0.0042 A/cm² of conventional carbon black (Pt/C, Vulcan XC-72) with a S_BET of ∼250 m²/g, a better electrochemical activity (a high current density of 0.0070 A/cm² for weak-H₂ adsorption/desorption) of the Pt/ACNTs with high specific surface area (S_BET) of 830-960 m²/g was obtained. Furthermore, the highest current density of 0.079 A/cm² at 0.65 V in anodic sweep was observed during the methanol oxidation. On the basis of Pt size, utility ratio, and electro-active specific surface area (EAS), the Pt/ACNTs with a high Pt-loading of 50 wt.% exhibited the best electrochemical activity. The present ACNTs may be an excellent support material for electrochemical catalyst in proton exchange membrane and direct methanol fuel cells.     

Direct electrochemistry of guanosine on multi-walled carbon nanotubes modified carbon ionic liquid electrode

A multi-walled carbon nanotubes (MWCNTs) modified carbon ionic liquid electrode (CILE) was fabricated and used to investigate the electrochemical behavior of guanosine. CILE was prepared by mixing hydrophilic ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF₄), graphite powder and liquid paraffin together. The fabricated MWCNTs/CILE showed great electrocatalytic ability to the oxidation of guanosine and an irreversible oxidation peak appeared at 1.067 V (vs. SCE) with improved peak current. The electrochemical behavior of guanosine on the MWCNTs/CILE was carefully studied by cyclic voltammetry and the electrochemical parameters such as the charge transfer coefficient (α) and the electrode reaction standard rate constant (k_s) were calculated with the result as 0.66 and 2.94 × 10⁻⁴ s⁻¹, respectively. By using differential pulse voltammetry (DPV) as the detection method, a linear relationship was obtained between the oxidation peak current and the guanosine concentration in the range from 1.0 × 10⁻⁷ to 4.0 × 10⁻⁵ mol/L with the detection limit as 7.8 × 10⁻⁸ mol/L (3σ). The common coexisting substances showed no interferences to the guanosine detection and the modified electrode showed good ability to distinguish the electrochemical response of guanosine and adenosine.     

Carbon monoxide oxidation on Au(1 1 1) surface decorated by spontaneously deposited Pt

Platinum is deposited spontaneously on Au(1 1 1) surface from 1 mM H₂PtCl₆ + 1 M HClO₄ solution using multiple deposition procedure. X-ray photoelectron spectroscopy (XPS) analysis has shown that after immersion into the Pt containing solution and rinsing with water, Pt(OH)₂ resides on the Au(1 1 1) substrate. Consecutive depositions as well as in situ scanning tunneling microscopy (STM) and electrochemical measurements are performed on previously electrochemically reduced Pt/Au(1 1 1) surfaces. Only homogeneous distribution of thus deposited Pt islands is observed by in situ STM. With subsequent depositions, the width of deposited Pt islands increases, but stays lower than 10 nm, while a significant increase of Pt islands height is observed, leading to moderate increase of the coverage. Cyclic voltammetry (CV) profiles of obtained Pt/Au(1 1 1) surfaces, and CO stripping curves are recorded in 0.5 M H₂SO₄ solution. CO oxidation takes place only at higher potentials shifting negatively with increasing coverage. This is discussed with respect to Pt islands width and height distributions and to the influence of the Au(1 1 1) substrate surface.     

Optimization of electrochemical properties of LiFePO4/C prepared by an aqueous solution method using sucrose

LiFePO₄ can be used as a positive electrode material for lithium-ion batteries by making composite with electrical conductive carbonaceous materials. In this study, LiFePO₄/C (carbon) composite was prepared by a soft chemistry route, in which sucrose was used as a carbon source of a low price. We tried to optimize a Li/(LiFePO₄/C) cell performance through changing synthetic conditions and discussed the factors affecting the electrochemical performances of the cell, such as the amount of the carbon source, synthetic temperature, gas flow rate of pyrolysis and the formation of secondary phases. It was found that the connection of the residual carbon and Fe₂P to LiFePO₄ particles and the amount of these two phases were important factors. In our experimental conditions, LiFePO₄/C including 9.72 wt.% of residual carbon, prepared at 800 °C for 12 h showed the highest reversible capacity and the best C rate performance among the synthesized materials; 130 mAh g⁻¹ at 10C rate and 50 °C.     

Synthesis and characterization of carbon-coated Li0.5Ni0.25TiOPO4 anode material

Li_0.5Ni_0.25TiOPO₄/C composite was synthesized by the co-precipitation method using polyethylene glycol as carbon source. X-ray diffraction study showed that the as-prepared material crystallizes in the monoclinic system (S.G. P2₁/c). This 3D structure exhibits an open framework favourable to intercalation reactions. The morphology and the microstructure characterisation was performed by scanning electron microscopy (SEM). Small particles (∼1 μm) coated by carbon were observed. Raman study confirms the presence of carbon graphite in the Li_0.5Ni_0.25TiOPO₄/C composite. Cyclic voltammetry (CV) and charge-discharge galvanostatic cycling were used to characterize its electrochemical properties. The Li_0.5Ni_0.25TiOPO₄/C composite exhibits excellent electrochemical performances with good capacity retention for 50 cycles. Approximately 200 mAh/g could be reached at C, C/2, C/5 and C/20 rates in the 0.5-3 V potential range. These results clearly evidenced the positive effect of the carbon coating on the electrochemical properties of the studied phosphate.     

Vanadium nitride as a novel thin film anode material for rechargeable lithium batteries

Vanadium mononitride (VN) thin films have been successfully fabricated by magnetron sputtering. Its electrochemical behaviour with lithium was examined by galvanostatic cell cycling and cyclic voltammetry. The capacity of VN was found to be stable above 800 mAh g⁻¹ after 50 cycles. By using ex situ X-ray diffraction, high-resolution transmission electron microscopy and selected area electron diffraction as well as in situ spectroelectrochemical measurements, the electrochemical reaction mechanism of VN with lithium was investigated. The reversible conversion reaction of VN into metal V and Li₃N was revealed. The high reversible capacity and good stable cycle of VN thin film electrode made it a new promising lithium-ion storage material for future rechargeable lithium batteries.     

Electrochemical behavior of uranium(VI) in 1-butyl-3-methylimidazolium chloride and thermal characterization of uranium oxide deposit

The electrochemical behavior of uranyl nitrate in 1-butyl-3-methylimidazolium chloride at glassy carbon working electrode has been investigated in the temperature range 343-373 K by transient electrochemical techniques such as cyclic voltammetry, chronopotentiometry and square wave voltammetry. Influence of bulk concentration of uranium and temperature on the electroreduction and transport properties of U(VI) in bmimCl has been examined. Diffusion coefficient (D) and the energy of activation (E_a) of U(VI) in bmimCl has been estimated and is of the order of ∼10⁻⁸ cm²/s and 54 kJ/mol, respectively. Reduction of U(VI) takes place through an irreversible single step two-electron transfer to UO₂ deposit at glassy carbon working electrode. Thermal analysis of the uranium oxide indicated the entrapment of nearly 5% of electrolyte, bmimCl, during electrodeposition, which decomposes in the range 553-653 K.     

Changes on iron electrode surface during hydrogen permeation in borate buffer solution

Hydrogen interaction with oxide films grown on iron electrodes at open circuit potential (E_oc) and in the passive region (+0.30 V_ECS) was studied by chronopotentiometry, chronoamperometry and electrochemical impedance spectroscopy techniques. The results were obtained in deaerated 0.3 mol L⁻¹ H₃BO₃ + 0.075 mol L⁻¹ Na₂B₄O₇ (BB, pH 8.4) solution before, during and after hydrogen permeation. The iron oxide film modification was also investigated by means of in situ X-ray absorption near-edge spectroscopy (XANES) and scanning electrochemical microscopy (SECM) before and during hydrogen permeation. The main conclusion was that the passive film is reduced during the hydrogen diffusion. The hydrogen permeation stabilizes the iron surface at a potential close to the thermodynamic water stability line where hydrogen evolution can occur. The stationary condition required for the determination of the permeation parameters cannot be easily attained on iron surface during hydrogen permeation. Moreover, additional attention must be paid when obtaining the transport parameters using the classical permeation cell.     

Evaluation of various strategies to formation of pH responsive hydroquinone-terminated films on carbon electrodes

The hydroquinone/quinone (H₂Q/Q) redox system was tethered to glassy carbon surfaces using first an electrochemical pre-oxidation treatment to afford carboxylic acid functionalities followed by immobilizing the H₂Q precursor, n-(2,5-dimethoxyphenyl)alkan-1-amine (general structure: H₂N-(CH₂)_n-C₆H₃(OCH₃)₂, n = 1, 2, 4, 8, and 12), by carbodiimide chemistry and a final demethylation reaction. The resultant surfaces exhibited the expected chemical reversibility in aqueous solution with a pH-sensitive position of the formal potential (∼55 mV/pH unit), and an increase in the peak potential separation going from 0.02 V for n = 1 to 0.21 V for n = 12. The films were very robust and could withstand prolonged sonication and relatively large potential excursions. While the films followed the expected kinetic distance dependence for up to 4 methylene units the electrode kinetics was faster than expected for longer alkyl spacers. We suggest that film disorder, electrode-mediating effects, and a roughened electrode material could account for these apparent inconsistencies. To further understand such effects, two complementary electrode modification strategies leading to better film ordering on carbon were adapted; immobilizing a thin layer of benzoic acid by oxidative deposition of 4-aminobenzoic acid or employing a plasma deposition process to tether an acid analogue. Analysis of the various electrodes was accomplished by electrochemical methods, atomic force microscopy, and X-ray photoelectron spectroscopy.     

Characterisation of activated nanoporous carbon for supercapacitor electrode materials

Commercial nanoporous carbon RP-20 was activated with water vapor in the temperature range from 950 °C to 1150 °C. The XRD analysis was carried out on nanoporous carbon powder samples to investigate the structural changes (graphitisation) in modified carbon that occurred at activation temperatures T ? 1150 °C. The first-order Raman spectra showed the absorption peak at 1582 cm⁻¹ and the disorder (D) peak at 1350 cm⁻¹. The low-temperature N₂ adsorption experiments were performed at −196 °C and a specific surface area up to 2240 m²g⁻¹ for carbon activated at T = 1050 °C was measured. The cell capacitance for two electrode activated nanoporous carbon system advanced up to 60 F g⁻¹ giving the specific capacitance ∼240 F g⁻¹ to one electrode nanoporous carbon ∣1.2 M (C₂H₅)₃CH₃NBF₄ + acetonitrile solution interface. A very wide region of ideal polarisability for two electrode system (∼3.2 V) was achieved. The low frequency limiting specific capacitance very weakly increases with the rise of specific area explained by the mass transfer limitations in the nanoporous carbon electrodes. The electrochemical characteristics obtained show that some of these materials under discussion can be used for compilation of high energy density and power density non-aqueous electrolyte supercapacitors with higher power densities than aqueous supercapacitors.     

Preparation and characterization of nano-particle LiFePO4 and LiFePO4/C by spray-drying and post-annealing method

Pure, nano-sized LiFePO₄ and LiFePO₄/C cathode materials are synthesized by spray-drying and post-annealing method. The influence of the sintering temperature and carbon coating on the structure, particle size, morphology and electrochemical performance of LiFePO₄ cathode material is investigated. The optimum processing conditions are found to be thermal treatment for 10 h at 600 °C. Compared with LiFePO₄, LiFePO₄/C particles are smaller in size due to the inhibition of crystal growth to a great extent by the presence of carbon in the reaction mixture. And that the LiFePO₄/C composite coated with 3.81 wt.% carbon exhibits the best electrode properties with discharge capacities of 139.4, 137.2, 133.5 and 127.3 mAh g⁻¹ at C/5, 1C, 5C and 10C rates, respectively. In addition, it shows excellent cycle stability at different current densities. Even after 50 cycles at the high current density of 10C, a discharge capacity of 117.7 mAh g⁻¹ is obtained (92.4% of its initial value) with only a low capacity fading of 0.15% per cycle.