理化因子对嗜盐隐杆藻细胞生长及胞外多糖产量的影响

比较不同ＮａＣｌ、Ｃａ２＋、ＰＯ３－４等离子浓度对嗜盐隐杆藻（Ａｐｈａｎｏｔｈｅｃｅｈａｌｏｐｈｙｔｉｃａ）细胞生长及胞外多糖（Ｅｘｏｐｏｌｙｓａｃ－ｃｈａｒｉｄｅＥＰＳ）产量的影响。在各影响因子不同浓度的培养条件下,０．５ｍｏｌ／Ｌ的ＮａＣｌ、１．０ｇ／Ｌ的Ｃａ（ＮＯ３）２·４Ｈ２Ｏ、０．１ｇ／Ｌ的ＫＨ２ＰＯ４分别是其最佳生长浓度。ＥＰＳ的产量在０．５ｍｏｌ／ＬＮａＣｌ、,０．５ｇ／ＬＣａ（ＮＯ３）２·４Ｈ２Ｏ、０．５ｇ／Ｌ的ＫＨ２ＰＯ４培养条件下最高。在较低的Ｃａ２＋、Ｍｇ２＋、ＰＯ３－４浓度下可提高ＥＰＳ产率。     

N,N-二辛基甘氨酸萃取铑的机理

报道了Ｎ，Ｎ－二辛基甘氨酸从盐酸体系中萃取铑的机理．结果表明：铑的萃取率随酸度、氯离子浓度、铑离子浓度的增大而降低．采用斜率法测得萃合物组成为：Ｒ２ＮＣＨ２ＣＯＯＨＨＲｈ（Ｈ２Ｏ）２Ｃｌ４．萃取反应方程式为：Ｒ２ＮＣＨ２ＣＯＯＨ．ＨＣｌ（Ｏ）＋Ｒｈ（Ｈ２Ｏ）２Ｃｌ－４（Ａ）＝Ｒ２ＮＣＨ２ＣＯＯＨ．ＨＲｈ（Ｈ２Ｏ）２Ｃｌ４（Ｏ）＋Ｃｌ     

影响中间相沥青电解加氢反应因素的研究

在隔离式电解槽中,用泡沫铅（ＳＰｂ）作阴极,铂（Ｐｔ）作阳极,饮和甘汞电极（ＳＣＥ）作参考电极,以ＣＨ３ＣＮ＋Ｃ２Ｈ５ＯＨ＋Ｈ２Ｏ＿Ｂｕ４ＮＢｒ为电解体系,对由煤沥青为原料制得的中国相沥青（ＭＰ）进行电解加氢研究,当ｃ（ＣＨ３ＣＮ）：ｃ（Ｃ２ＨＯＨ）：ｃ（Ｈ２Ｏ）＝０．４：０．１：１（浓度比）,ｃ（Ｂｕ４ＮＢ４）＝０．３１ｍｏｌ／Ｌ,ｔ＝３０Ｃ,ｐ（ＭＰ）＝５０ｇ／Ｌ,阴极电解电位为－２．４Ｖ时,     

液膜法富集镉（II）与测定镀液中微量镉

用Ｐ２１５－ＴＯＰＯ－ＳＰＡＮ８０－液体石蜡－内相（ＨＣｌ溶液）乳状液膜体系研究了Ｃｄ＾２＋的迁移行为，只有Ｃｄ＾２＋能与各种阳离子得到满意的分离。最佳液膜体系为４％Ｐ２１５、２％ＴＯＰＯ、５％ＳＰＡＮ８０、４％液体石蜡、８５％煤油和内相（４ｍｏｌ／Ｌ ＨＣＬ）。确定了分离与富集镉（Ⅱ）的最优实验条件，Ｒｏｉ＝１：１（油内比），Ｒｅｗ＝２０：１２０（乳水比）。用此法已成功地测定镀液和工业废水中微量     

金—钼酸盐—丁基罗丹明B体系显色反应研究

研究了在高氯酸和聚乙烯醇（ＰＶＡ）存在下，金与钼酸盐和丁基罗丹明Ｂ（ＢＲＢ）的显色反应。其适宜条件ＣＨＣｌＯ４＝１．５ｍｏｌ／Ｌ，ＣＭｏＯ２－４＝９．１×１０－４ｍｏｌ／Ｌ，ＣＢＲＢ＝３．８×１０－５ｍｏｌ／Ｌ及０．０８％ＰＶＡ。金钼杂多酸—丁基罗丹明Ｂ离子缔合物的最大吸收位于５７０ｎｍ，表观摩尔吸光系数为３．３６×１０６Ｌ·ｍｏｌ－１·ｃｍ－１，金量在０～４０μｇ／Ｌ范围内服从比尔定律，测定极限（Ｓ／Ｎ＝３）０．９０μｇ／Ｌ（ｎ＝１０），对于２８μｇＡｕ（Ⅲ）／Ｌ测定的相对标准偏差２．１％（ｎ＝７）。缔合物至少可稳定５ｈ，摩尔比Ａｕ∶ＢＲＢ＝１∶３。考察了４４种共存离子的影响，大多数常见离子不干扰，用活性炭分离富集金，对砂矿和炭粉中金的测定，结果满意。     

1-苯基-3-甲基-4-(α-呋喃甲酰基)-5-吡唑酮与中性磷萃取剂对钍(IV)的协同萃取

研究了１－苯基－３－甲基－４－（α－呋喃甲酰基）－５－吡唑酮（ＨＰＭＦＰ,ＨＡ）与氧化三正辛基膦（ＴＯＰＯ,Ｂ）或氧化三苯基膦（ＴＰＰＯ,Ｂ）的甲苯溶液从硝酸介质中对钍（ＩＶ）的协同萃取行为．用斜率法确定了ＨＡ－ＴＰＰＯ－Ｃ６Ｈ５ＣＨ３体系萃取钍（ＩＶ）的协萃配合物组成为ＴｈＡ４·ＴＰ－ＰＯ,求得了体系的协萃平衡常数,比较了在不同稀释剂中ＨＡ－ＴＰＰＯ对钍（ＩＶ）的萃取能力     

磷酸三丁酯为载体的乳状液膜体系迁移钇(Ⅲ)的研究

用磷酸三丁酯（ＴＢＰ）－ＬＭＳ－２－磺化煤油乳状液膜体系研究了Ｙ（Ⅲ）的迁移行为。当膜相体积分数为５．０％ＴＢＰ和２．０％ＬＭＳ－２,内相为０．０１ｍｏｌ／ＬＮａＨＣＯ３,外相含６ｍｏｌ／ＬＮＨ４ＮＯ３,酸度为ｐＨ＝３时,Ｙ（Ⅲ）能快速并完全迁移。常见过渡元素离子如Ｆｅ２＋,Ｃｏ２＋,Ｎｉ２＋,Ｍｎ２＋,Ｚｎ２＋等均不迁移,故可以从这些离子的混合液中分离Ｙ（Ⅲ）,回收率可达９８％以上。     

液膜法分离富集,测定水中微量锶

用状液膜体系对锶进行分离富集，该体系包括协同流动载体（ＰＭＢＰ、ＴＢＰ）、表面活性剂（ＳＰＡＮ８０）、增强剂（丙三醇）、溶剂（正己烷）和内相（１．２ｍｏｌ／Ｌ的盐酸溶液）。实验表明，在适宜的条件下，锶的富集效率可达９９．５％以上，而在此条件下许多共存离子，如Ｆｅ＾３＋、Ａｌ＾３＋、Ｃａ＾２／、Ｍｇ＾２＾＋、Ｃｒ＾３＋、Ｃｏ＾２＋、Ｎｉ＾２＋、Ｚｒ＾４＋、Ｃｕ＾２＋、Ｚｎ＾２＋、Ｐｂ＾２＋和ＲＥ＾３     

磷酸三丁酯为载体的乳状液膜体系迁移钇(Ⅲ)的研究

本文用磷酸三丁酯（ＴＢＰ）－ＬＭＳ－２磺化煤油乳状液膜体系研究了Ｙ（Ⅲ）的迁移行为。当膜相组成为５．０％ＴＢＰ的２．０％ＬＭＳ－２,内相为０．１０ｍｏｌ／ｄｍ＾３ＮａＨＣＯ３,外相含６ｍｏｌ／ｄｍ＾３,ＮＨ４ＮＯ３,酸度为ｐＨ＝３时,Ｙ能快速并完全迁移。     

液膜法富集镉（Ⅱ）与测定镀液中微量镉

用Ｐ２１５－ＴＯＰＯ－ＳＰＡＮ８０－液体石蜡－煤油－内相（ＨＣｌ溶液）乳状液膜体系研究了Ｃｄ（２＋）的迁移行为，只有Ｃｄ~２能与各种阳离子得到满意的分离。最佳液膜体系为４％Ｐ２１５、２％ＴＯＰＯ、５％　ＳＰＡＮ８０、４％液体石蜡、８５％　煤油和内相（４ｍｏｌ／ＬＨＣｌ）。确定了分离与富集镉（Ⅱ）的最优实验条件，Ｒｏｉ＝１：１（油内比），Ｒｅｗ＝２０：１２０（乳水比）。用此法已成功地测定镀液和工业废水中微量镉，其回收率为９９．４％以上，相对标准偏差在３．７％以下，结果满意。     

Quantification of Phospholipids Classes in Human Milk

Phospholipids are integral constituents of the milk fat globule membranes and they play a central role in infants’ immune and inflammatory responses. A methodology employing liquid chromatography coupled with evaporative light scattering detector has been optimized and validated to quantify the major phospholipids classes in human milk. Phospholipids were extracted using chloroform and methanol and separated on C18 column. Repeatability, intermediate reproducibility, and recovery values were calculated and a large sample set of human milk analyzed. In human milk, phospholipid classes were quantified at concentrations of 0.6 mg/100 g for phosphatidylinositol; 4.2 mg/100 g for phosphatidylethanolamine, 0.4 mg/100 g for phosphatidylserine, 2.8 mg/100 g for phosphatidylcholine, and 4.6 mg/100 g for sphingomyelin. Their relative standard deviation of repeatability and intermediate reproducibility values ranging between 0.8 and 13.4 % and between 2.4 and 25.7 %, respectively. The recovery values ranged between 67 and 112 %. Finally, the validated method was used to quantify phospholipid classes in human milk collected from 50 volunteers 4 weeks postpartum providing absolute content of these lipids in a relatively large cohort. The average content of total phospholipids was 23.8 mg/100 g that corresponds to an estimated mean intake of 140 mg phospholipids/day in a 4-week old infant when exclusively breast-fed.     

The hydration of reactive cement-in-polymer dispersions studied by nuclear magnetic resonance

The behaviour of two novel cement-in-polymer (c/p) dispersions, namely cement-in-poly(vinyl acetate) and cement-in-poly(vinyl alcohol) upon exposure to water at room temperature was investigated by a combination of various NMR methods. The swelling, cracking, and the water ingress were monitored non-destructively using ¹H single point imaging. The hydration of the cement matrix was investigated using ²⁹Si NMR whilst ¹³C CPMAS NMR spectra allowed the quantification of the kinetics of the hydrolysis reaction of poly(vinyl acetate) into poly(vinyl alcohol). The polymer controls the rate of water ingress and swelling which in turn determines the behaviour of the c/p dispersions upon exposure to water. For the cement-in-poly(vinyl alcohol), the rates of water ingress and swelling are much faster than the hydration of the clinker whilst for the cement-in-poly(vinyl acetate) the slow rates of the two processes allow the formation of a cementious matrix which assures the stability of the sample.     

Interactions between shrinkage reducing admixtures (SRA) and cement paste's pore solution

Shrinkage reducing admixtures (SRA) have been developed to combat shrinkage cracking in concrete elements. While SRA has been shown to have significant benefits in reducing the magnitude of drying and autogenous shrinkage, it has been reported that SRA may cause a negative side effect as it reduces the rate of cement hydration and strength development in concrete. To examine the influence of SRA on cement hydration, this study explores the interactions between SRA and cement paste's pore solution. It is described that SRA is mainly composed of amphiphilic (i.e., surfactant) molecules that when added to an aqueous solution, accumulate at the solution-air interface and can significantly reduce the interfacial tension. However, these surfactants can also self-aggregate in the bulk solution (i.e., micellation) and this may limit the surface tension reduction capacity of SRA. In synthetic pore solutions, SRA is observed to form an oil-water-surfactant emulsion that may or may not be stable. Specifically, at concentrations above a critical threshold, the mixture of SRA and pore fluid is unstable and can separate into two distinct phases (an SRA-rich phase and an SRA-dilute phase). Further, chemical analysis of extracted pore solutions shows that addition of SRA to the mixing water depresses the dissolution of alkalis in the pore fluid. This results in a pore fluid with lower alkalinity which causes a reduction in the rate of cement hydration. This may explain why concrete containing SRA shows a delayed setting and a slower strength development.     

Design and function of novel superplasticizers for more durable high performance concrete (superplast project)

In this article we shall describe our quest and ultimate success in furthering our understanding of the action of superplasticizers on the rheology of cement and concrete. By specifically producing superplasticizers with varied architectures, we have been able to show the important structural features of the macromolecules that lead to a successful superplasticizer or water reducing agent. Both polycarboxylate and lignosulfonate polymers have been investigated. Using both non-reactive model MgO powders, three different types of cement blends, the adsorption behaviour and the effect on the rheological properties of these two important superplasticizer families have been used to further develop a conceptual model for superplasticizer — cement behaviour. This paper will deal mainly with the conceptual model, the materials and methods used to asses the polymer adsorption behaviour and rheological properties of the systems studied. We shall briefly describe the adsorption of the polymers onto the different surfaces and their influence on surface charge and rheology and the influence of the various ionic species found in cement pore solutions that may influence polymer-cement affinity. The key factors are shown to be the effective adsorbed polymer thickness and the induced surface charge which can be influenced by the polymer architecture, the pore solution composition and the initial particle surface charge.     

Study of the hydration of CaO powder by gas–solid reaction

Hydration of CaO powders by reaction with water vapor has been studied in isothermal and isobaric conditions. Experimental tests were performed within the temperature range of 70 °C–420 °C and with a water vapor pressure from 5 to 160 hPa by means of a thermogravimetric device. Two powders, exhibiting slight differences in their physical properties, were studied. However, for one of the powders and under some temperature and pressure conditions, the reaction is not complete. The difference of behavior between both CaO powders was interpreted by considering the effect of the morphological properties on the mechanism of growth of Ca(OH)₂.     

The influence of water removal techniques on the composition and microstructure of hardened cement pastes

The removal of water from hardened cement paste for analysis or to arrest ongoing hydration has been reported to affect the composition of hydrated phases and microstructure. The effect that arresting the hydration of hardened cement paste by replacing the pore water with acetone before drying, and by removing the water by freeze, vacuum and oven drying has on the hardened cement paste has been investigated. Two pastes were studied, a cemented iron hydroxide floc where a high proportion of ordinary Portland cement (OPC) had been replaced by pulverised fuel ash, and a pure hydrated OPC. The results showed that none of the water removal techniques caused any major deterioration in the composition and microstructure of the hardened cement pastes studied, but the pores appeared better preserved after arresting hydration using acetone quenching. Freeze drying appeared to cause more cracking of the microstructure than the other water removal techniques.     

2-(2'-咪唑偶氮)萘酚-4-磺酸的合成及其分析性质的研究

合成了新显色剂咪唑偶氮－２－萘酚－４－磺酸（ＩＡＮ－４Ｓ）,研究了试剂的离解常数及其与金属离子的显色反应。     

Influence of bleed water reabsorption on cement paste autogenous deformation

The effects of bleed water reabsorption and subsequent early age expansion on observed autogenous deformation are investigated in this research. Bleeding was induced by varying superplasticizer and shrinkage-reducing admixture dosages and by increasing the water-to-cement ratio. This research revealed that significant early age expansion occurs with increasing chemical admixture dosages and higher water-to-cement ratios, as expected, due to increasing bleeding of those samples. When samples were rotated, negligible early age expansion was observed. Thus, bleed water reabsorption is shown to be the primary mechanism causing initial expansion in sealed autogenous deformation samples. Thermal dilation and ettringite growth appear to have a minimal influence on the observed expansion. Rotating the samples during setting eliminates the potential for bleed water reabsorption and is recommended for all autogenous deformation testing.     

Comparison between surface and bulk hydrophobic treatment against corrosion of galvanized reinforcing steel in concrete

The effectiveness of bulk hydrophobic treatment against corrosion of galvanized steel reinforcement in concrete specimens with w/c = 0.45 and w/c = 0.75 was compared with that of surface treatment, even in the presence of cracks 0.5 and 1 mm wide in the concrete cover. In this case surface hydrophobic treatments were applied both before and after cracking as a preventive and a restorative method against reinforced concrete deterioration, respectively. The obtained results in terms of water absorption, electrochemical measurements, chlorides penetration, and visual observations carried out on reinforced concrete specimens during the exposure to wet–dry cycles in 10% NaCl solution showed that bulk hydrophobization is the most effective treatment in improving the corrosion resistance of galvanized steel reinforcements in concrete also in the presence of cracks. Surface hydrophobization is very effective just in the first few exposure cycles to the aggressive environment and when used as a restorative method which is able to cancel the deleterious effect of cracks only 0.5 mm wide.     

Effect of plasma treatment of polymeric tape carriers on wetting behaviour of aqueous ceramic tape casting slurry

Due to environmental and health aspects, aqueous ceramic slurries are preferred to traditional organic solvent systems in tape casting. An important obstacle associated with the high surface energy of water is poor wetting of aqueous ceramic slurries on polymeric tape carriers. Therefore, we measured the contact angles of an aqueous epoxy-based ceramic slurry on polyethylene terephtalate (PET), polypropylene (PP), polymethyl methacrylate (PMMA), and aluminium-coated polyethylene terephtalate (PET-Al) films and investigated approaches to improving their wetting. We evaluated the effect of plasma treatment of the tape carrier surface on the wetting behaviour and compared it with the effect of adding non-ionic amphiphilic surfactants to the ceramic slurry. The treatment of the tape carrier surface by low-temperature plasma substantially improved the wetting behaviour of aqueous ceramic slurry. The lowest contact angle of 31° was obtained on the PET film. Although the addition of non-ionic surfactants improved both the wetting behaviour of the slurry and the detachment of the polymeric carrier from the ceramic tape even better than the plasma treatment of the carrier surface did, the plasma-treated carriers still present a useful alternative to the surfactants. In the case of the plasma-treated PET carrier the surfactants could be fully eliminated and potential drawbacks related to the use of surfactants could be prevented.