Characterization of Supported NiSO4 and Effect of TiO2–ZrO2 Composition on Catalytic Activity for Acid Catalysis

A series of catalysts, NiSO₄/TiO₂–ZrO₂ having different TiO₂–ZrO₂ composition, for acid catalysis was prepared by the impregnation method using an aqueous solution of nickel sulfate. The addition of TiO₂ to ZrO₂ improved the surface area of the catalyst and enhanced its acidity remarkably because of the formation of new acid sites through the charge imbalance of Ti–O–Zr bonding. The binary oxide, TiO₂–ZrO₂ calcined above 600 °C resulted in the formation of crystalline orthorhombic phase of ZrTiO₄. Therefore, NiSO₄/TiO₂–ZrO₂ calcined at 500 °C exhibited a maximum catalytic activity for acid catalysis, and then the catalytic activity decreased with the calcination temperature. The correlation between catalytic activity and acidity held for both reaction, 2-propanol dehydration and cumene dealkylation. NiSO₄ supported on 50TiO₂–50ZrO₂ (TiO₂/ZrO₂ ratio = 1) among TiO₂–ZrO₂ binary oxides exhibited the highest catalytic activity for acid catalysis.     

Catalytic Activities of Al2O3-promoted NiSO4/TiO2 for Acid Catalysis

A series of catalysts, NiSO₄/Al₂O₃–TiO₂, for acid catalysis was prepared by the impregnation method, where support, Al₂O₃–TiO₂ was prepared by the coprecipitation method using a mixed aqueous solution of titanium tetrachloride and aluminum nitrate solution followed by adding an aqueous ammonia solution. The addition of nickel sulfate (or Al₂O₃) to TiO₂ shifted the phase transition of TiO₂ from amorphous to anatase to higher temperature because of the interaction between nickel sulfate (or Al₂O₃) and TiO₂. 15-NiSO₄/5-Al₂O₃–TiO₂ containing 15 wt% NiSO₄ and 5 mol% Al₂O₃, and calcined at 400°C exhibited maximum catalytic activities for both reactions, 2-propanol dehydration and cumene dealkylation. The catalytic activities for both reactions were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The charge transfer from Ti atoms to the neighboring Al atoms strengthens the Al–O bond between Al and the surface sulfate species. The addition of Al₂O₃ up to 5 mol% enhanced the acidity, thermal property, and catalytic activities of NiSO₄/Al₂O₃–TiO₂ gradually due to the interaction between Al₂O₃ and TiO₂ and consequent formation of Al–O–Ti bond.     

Cracking of n-Butane Over Alkaline Earth-Containing HZSM-5 Catalysts

A series of catalysts, NiSO₄/SiO₂–Al₂O₃, for ethylene dimerization were prepared by the impregnation method using aqueous solution of nickel sulfate. Although SiO₂–Al₂O₃ without NiSO₄ was inactive as catalyst for ethylene dimerization, the SiO₂–Al₂O₃ with NiSO₄ exhibited high catalytic activity even at room temperature. The high catalytic activity of NiSO₄/SiO₂–Al₂O₃ was closely correlated with the increase of acidity and acid strength due to the addition of NiSO₄. The sample having 15 wt% of NiSO₄ and calcined at 500 °C for 1.5 h exhibited maxima for catalytic activity and acidity. In view of IR results of CO adsorbed on NiSO₄/SiO₂–Al₂O₃, it is concluded that the active sites responsible for ethylene dimerization consist of a low-valent nickel, Ni⁺, and an acid.     

Characterization of nickel sulfate supported on γ-Al2O3 and its relationship to acidic properties

A series of NiSO₄/γ-Al₂O₃ catalysts were prepared by the impregnation method using an aqueous solution of nickel sulfate. The high catalytic activity of NiSO₄/γ-Al₂O₃ for both 2-propanol dehydration and cumene dealkylation was related to the increase of acidity and acid strength due to the addition of NiSO₄. 20(wt%)-NiSO₄/g-Al₂O₃ calcined at 600 °C exhibited maximum catalytic activities for 2-propanol dehydration and cumene dealkylation. The catalytic activities for both reactions were correlated with the acidity of catalysts measured by the ammonia chemisorption method. This paper is dedicated to Professor Wha Young Lee on the occasion of his retirement from Seoul National University.     

Characterization of zirconium sulfate supported on TiO2 and activity for acid catalysis

A series of Zr(SO₄)₂/TiO₂ catalysts were prepared by impregnation of powder TiO₂ with an aqueous solution of zirconium sulfate. No diffraction line of zirconium sulfate was observed up to 30 wt%, indicating good dispersion of Zr(SO₄)₂ on the surface of TiO₂. The high catalytic activities of Zr(SO₄)2/TiO₂ for both 2-propanol dehydration and cumene dealkylation were related to the increase of acidity and acid strength due to the addition of Zr(SO₄)₂. Zr(SO₄)₂/TiO₂ containing 25% zirconium sulfate and calcined at 400 °C exhibited maximum catalytic activities for 2-propanol dehydration and cumene dealkylation. The catalytic activities for these reactions were correlated with the acidity of catalysts measured by the ammonia chemisorption method. This paper is dedicated to Professor Hyun Ku Rhee on the occasion of his retirement from Seoul National University.     

Dehydrogenation of ethylbenzene over TiO2-Fe2O3 and ZrO2-Fe2O3 mixed oxide catalysts

The mixed metal oxides TiO₂-Fe₂O₃ and ZrO₂-Fe₂O₃ were examined as potential catalysts for the dehydrogenation reaction of ethylbenzene. The acidic and basic properties and surface area, pore volume and pore size distribution of these catalysts were measured. The catalytic activities can be correlated very well with the surface area and the acidity and basicity of ZrO₂-Fe₂O₃ catalysts. However, for TiO₂-Fe₂O₃ catalysts, the surface area, the amount of acidic and basic sites and TiFe₂O₅ crystallinity are all important factors affecting the catalytic activities for ethylbenzene dehydrogenation. A synergistic effect was found for the TiO₂-Fe₂O₃ and ZrO₂-Fe₂O₃ catalyst system and also for the TiO₂-Fe₂O₃-ZrO₂ system, i.e. the activities of these catalysts can be ranked in the following order: TiO₂-Fe₂O₃-ZrO₂>TiO₂-Fe₂O₃ >ZrO₂>Fe₂O₃>TiO₂. Meanwhile, all of these catalysts showed higher activities than the conventional potassium-promoted iron catalysts.     

Ethylene dimerization catalyst of nickel sulfate supported on silica-alumina

Catalysts containing various nickel sulfate content were prepared by dry impregnation of silica-alumina or silicagel with aqueous solution of nickel sulfate. SiO₂-Al₂O₃ alone without NiSO₄ was totally inactive for the ethylene dimerization reaction at room temperature. However, NiSO₄/SiO₂-Al₂O₃ was found to be very active even at room temperature compared with NiSO₄/SiO₂.     

The Effects of Al2O3 Addition and WO3 Modification on Catalytic Activities of NiO/TiO2 for Acid Catalysis

NiO/Al₂O₃–TiO₂/WO₃ catalysts for acid catalysis were prepared by the addition of Al₂O₃ and the modification with WO₃. The strong acid sites were formed through the bonding between dispersed WO₃ and TiO₂. The larger the dispersed WO₃ amount, the higher both the acidity and catalytic activity. The addition of Al₂O₃ up to 5 mol% enhanced acidity and catalytic activity of NiO/Al₂O₃–TiO₂/WO₃ gradually due to the interaction between Al₂O₃ and TiO₂ and consequent formation of Al–O–Ti bond. The presence of NiO may attract reactants and enhance the local concentration of reactants near acid sites and consequently increase catalytic activity.     

Oxidation of CH4 over Pd supported on TiO2-doped SiO2: Effect of Ti(IV) loading and influence of SO2

Titania-modified silicas with different weight% of TiO₂ were prepared by sol–gel method and used as supports for Pd (1 wt%) catalysts. The obtained materials were tested in the oxidation of methane under lean conditions in absence and in presence of SO₂. Test reactions were consecutively performed in order to evaluate the thermal stability and poisoning reversibility. Increasing amounts of TiO₂ improved the catalytic activity, with an optimum of the performance for 10 wt% TiO₂ loading. Moreover, the titania-containing catalysts exhibited a superior tolerance towards SO₂ by either adding it to the reactants or feeding it as a pure pretreatment atmosphere at 350 °C. Catalysts were characterized by XPS, XRD, FT-IR and BET measurements. According to the structural and surface analyses, the mixed oxides contained Si–O–Ti linkages which were interpreted as being responsible for the enhanced intrinsic activity of supported PdO with respect to PdO on either pure SiO₂ or pure TiO₂. Moreover, the preferential interaction of the sulfur molecule with TiO₂ and the easy SO_x desorption from high surface area silica were the determining factors for the superior SO₂ tolerance of the TiO₂-doped catalysts.     

Hydrogen production by steam reforming of LNG over Ni/Al2O3-ZrO2 catalysts: Effect of ZrO2 and preparation method of Al2O3-ZrO2

An Al₂O₃-ZrO₂ support was prepared by grafting a zirconium precursor onto the surface of commercial γ-Al₂O₃. A physical mixture of Al₂O₃-ZrO₂ was also prepared for the purpose of comparison. Ni/Al₂O₃-ZrO₂ catalysts were then prepared by an impregnation method, and were applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). The effect ZrO₂ and preparation method of Al₂O₃-ZrO₂ on the performance of supported nickel catalysts in the steam reforming of LNG was investigated. The Al₂O₃-ZrO₂ prepared by a grafting method was more efficient as a support for nickel catalyst than the physical mixture of Al₂O₃-ZrO₂ in the hydrogen production by steam reforming of LNG. The well-developed tetragonal phase of ZrO₂ and the high dispersion of ZrO₂ on the surface of γ-Al₂O₃ were responsible for the enhanced catalytic performance of Ni/Al₂O₃-ZrO₂ prepared by way of a grafting method.     

Effects of Na Addition, Pyridine Preadsorption, and Water Preadsorption on the Hydrogen Adsorption Property of Pt/SO4 2--ZrO2

Hydrogen adsorption was studied for Pt/SO₄ ^2--ZrO₂ samples modified with Na addition, pyridine preadsorption, and water preadsorption to elucidate the relation between the rate and capacity of hydrogen adsorption and the surface state. The surface states were monitored by XRD, IR, ammonia TPD, and measurement of catalytic activity for cyclohexane isomerization. All the modifications suppressed the hydrogen uptake. It was suggested that Lewis acid sites promote the hydrogen uptake by stabilizing spiltover hydrogen atoms.     

Catalytic combustion of benzene over supported metal oxides catalysts

Catalytic combustion of benzene over supported metal oxides has been investigated. The catalysts have been prepared by incipient wetness method and characterized by XRD, FT-Raman, ESR and TPR. Among supported metal oxides, CuO_x, supported on TiO₂ is found to have the highest activity for benzene oxidation. In addition, among the catalysts of copper oxide supported on TiO₂, A1₂O₃ and SiO₂, titania-supported catalyst (CuO_x/TiO₂) gives the highest catalytic activity. CuO_x/TiO₂ (Cu loading 5.5 wt%) shows the total oxidation of benzene at about 250 °C. From the ESR and FT-Raman results, the CuO dispersed on the TiO₂ surface acts as an active site of CuO_x/TiO₂ catalysts on the oxidative decomposition of benzene. The catalytic activity gradually increases with an increase of Cu loading on TiO₂. When Cu loading reaches 5.5 wt%, the total conversion temperature is lowered to 300 °C. However, the catalytic activity considerably decreases at 7 wt% Cu loading. The catalytic activity increased with an increase of oxygen concentration but the concentration of benzene showed no difference in the benzene conversion. This result suggests that the rate determining step is the adsorption of oxygen.     

High activity Ni/MoS2 catalysts obtained from alkylthiometalate mixtures for the hydrodesulfurization of dibenzothiophene

An efficient method for improving the catalytic properties of unsupported Ni/MoS₂ catalysts is mixing thiometalate precursors applying the appropriate precursors and thermal conditions. High active catalysts for the hydrodesulfurization (HDS) of dibenzothiophene (DBT) are prepared by the controlled decomposition of physical mixtures of Ni(diethylentriamine)₂MoS₄ (NDTA-TM) and [(Propyl)₄N)]₂MoS₄ (TPA-TM). The catalysts with a higher content of NDTA-TM are very active with a high selectivity for the direct desulfurization pathway (DDS) due to the synergistic effect of nickel. In addition the presence of a large amount of carbon may produce single-slabs of nickel promoted carbon containing molybdenum sulfides. The activity enhancement is attributed to an increased number of NiMoS active sites originated by the chemical interaction between the precursors NDTA-TM and TPA-TM during the mixing procedure. Furthermore, the carbon content in the final products is related to the enhancement of the activity and the preference of the DDS pathway. The controlled decomposition of mixtures of NDTA-TM + TPA-TM yields catalysts which are about twofold more active than an industrial NiMo/Al₂O₃ catalyst. This improvement may be attributed to an intense interaction of the precursors during the synthesis causing a re-dispersion of nickel atoms from NDTA-TM over the surface of carbon containing molybdenum sulfide provided by the precursor TPA-TM, increasing the amount of active sites. The catalysts from mixtures of (NH₄)₂MoS₄ (A-TM) and NDTA-TM behave similarly to the pure precursors.     

Effect of Ag addition on the properties of Pd–Ag/TiO2 catalysts containing different TiO2 crystalline phases

Anatase and rutile TiO₂ were used for preparation of the TiO₂ supported Pd and Pd–Ag catalysts for selective hydrogenation of acetylene. It was found that Pd/TiO₂-anatase exhibited higher acetylene conversion and ethylene selectivity than rutile TiO₂ supported ones. However, addition of Ag to Pd/TiO₂-anatase catalyst resulted in lower ethylene selectivity while that of Pd/TiO₂-rutile increased. It is suggested that Ag addition suppressed the beneficial effect of the Ti³⁺ sites presented on the anatase TiO₂ during selective acetylene hydrogenation whereas without Ti³⁺, Ag promoted ethylene selectivity by blocking sites for over-hydrogenation of ethylene to ethane.     

TPD study of the reaction of CH3CH2SH and (CH3CH2)2S2 on ZnO(0001) and ZnO

Superior activation of on 1 wt% Pt/TiO₂ catalysts for the oxidation of CO was attained by loading a large amount of Fe-oxide (100 wt%) and TiO₂. In situ IR spectra of CO proved that the structural transformation is brought about on the Pt-sites by loading of Fe-oxide, where predominant Pt-sites giving linear CO change to highly reactive bridge CO Pt-sites. In contrast, no transformation of the linear CO sites to the bridge CO sites takes place by loading of TiO₂ but the environment of Pt-sites for linear CO is changed.     

Low temperature selective catalytic reduction of NO by NH3 over V2O5 supported on TiO2–SiO2–MoO3

The V₂O₅ catalysts supported on TiO₂–SiO₂–MoO₃ (TSM) prepared by the coprecipitation method were investigated for the selective catalytic reduction (SCR) of NO by NH₃ at low temperatures. The V₂O₅/TSM catalyst with 7–13 wt% SiO₂ was found to exhibit a superior SCR activity and a good sulfur tolerance at low temperatures (<250 °C). The presence of highly active polymeric vanadates formed by the incorporation of MoO₃ to TiO₂–SiO₂ and superior redox properties seems to enhance SCR activity, and furthermore the very lower SO₂ oxidation activity due to the higher acidity leads to the remarkable improvement of sulfur tolerance.     

Oxidative dehydrogenation of ethane by carbon dioxide over sulfate‐modified Cr2O3/SiO2 catalysts

The oxidative dehydrogenation of ethane into ethylene by carbon dioxide over unsupported Cr₂O₃, Cr₂O₃/SiO₂ and a series of Cr₂O₃/SiO₂ catalysts modified by sulfate was investigated. The results show that Cr₂O₃/SiO₂ is an effective catalyst for dehydrogenation of ethane and CO₂ in the feed promotes the catalytic activity. Sulfation of silica will influence the catalytic behavior of Cr₂O₃/SiO₂ in dehydrogenation of ethane with carbon dioxide depending on the amount of sulfate. Cr₂O₃/6 wt% SO ₄ ^2- –SiO₂ catalysts exhibit an excellent performance for this reaction, giving an ethylene yield of 55% at 67% ethane conversion at 650°C. Characterizations indicate that addition of sulfate changes the bulk and surface properties of Cr₂O₃/SiO₂, promoting the reduction of Cr⁶⁺ to Cr³⁺ and favoring the catalytic conversion. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation and characterization of SO42-/TiO2 and S2O82-/TiO2 catalysts

Nanosized solid superacids SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂, as well as MCM-41-supported SO₄ ²⁻/ZrO₂, were prepared. Their structures, acidities, and catalytic activities were investigated and compared using XRD, N₂ adsorption-desorption, and in situ FTIR-pyridine adsorption, as well as an evaluation reaction with pseudoionone cyclization. The results showed that SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ possess not only nanosized particles with diameters < 7.0 nm, a BET surface greater than 140 cm²/g and relatively regular mesostructures with pores around 4.0 nm, but also a pure anatase phase and strong acidity. Different from the Lewis acid nature of SO₄ ²⁻/ZrO₂/MCM-41, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibit mainly Bronsted acidities. The strongest Bronsted acid sites were produced on SO₄ ²⁻/TiO₂ promoted with H₂SO₄, while Lewis acid sites on S₂O₈ ²⁻/TiO₂ even stronger than those on SO₄ ²⁻/ZrO₂/MCM-41 were generated when persulfate solution was used as sulfating agent. Because of their distinct acid natures, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibited catalytic activities for the cyclization of pseudoionone that were much higher than that of SO₄ ²⁻/ZrO₂/MCM-41. It can be concluded that the existence of more Br?nsted acid sites was favorable for proton participation in the cyclization reaction. Translated from Journal of Chemical Engineering of Chinese Universities, 2006, 20(2): 239–244 [译自: 高校化学工程学报]     

Role of support in reforming of CH4 with CO2 over Rh catalysts

The reforming of CH₄ with CO₂ over supported Rh catalysts has been studied over a range of temperatures (550–1000 K). A significant effect of the support on the catalytic activity was observed, where the order was Rh/Al₂O₃>Rh/TiO₂>Rh/SiO₂. The catalytic activity of Rh/SiO₂ was promoted markedly by physical mixing of Rh/SiO₂ with metal oxides such as Al₂O₃, TiO₂, and MgO, indicating a synergetic effect. The role of the metal oxides used as the support and the physical mixture may be ascribed to the promotion in dissociation of CO₂ on the surface of Rh, since the CH₄ + CO₂ reaction is first order in the pressure of CO₂, suggesting that CO₂ dissociation is the rate-determining step. The possible model of the synergetic effect was proposed.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> xerogel support on hydrogen production by steam reforming of LNG over Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> catalyst

An Al₂O₃-ZrO₂ xerogel (AZ-SG) was prepared by a sol-gel method for use as a support for a nickel catalyst. The Ni/AZ-SG catalyst was then prepared by an impregnation method, and was applied to hydrogen production by steam reforming of LNG. A nickel catalyst supported on commercial alumina (A-C) was also prepared (Ni/A-C) for comparison. The hydroxyl-rich surface of the AZ-SG support increased the dispersion of nickel species on the support during the calcination step. The formation of a surface nickel aluminate-like phase in the Ni/AZ-SG catalyst greatly enhanced the reducibility of the Ni/AZ-SG catalyst. The ZrO₂ in the AZ-SG support increased the adsorption of steam onto the support and the subsequent spillover of steam from the support to the active nickel sites in the Ni/AZ-SG catalyst. Both the high surface area and the well-developed mesoporosity of the Ni/AZ-SG catalyst improved the gasification of adsorbed surface hydrocarbons in the reaction. In the steam reforming of LNG, the Ni/AZ-SG catalyst showed a better catalytic performance than the Ni/A-C catalyst. Moreover, the Ni/AZ-SG catalyst showed strong resistance toward catalyst deactivation.