Ethylene/1‐octadecene copolymerization using [η5:η1‐C5Me4‐4‐R1‐6‐R‐C6H2O]TiCl2 catalysts

Copolymerization of ethylene with 1‐octadecene was studied using [η⁵:η¹‐C₅Me₄‐4‐R₁‐6‐R‐C₆H₂O]TiCl₂ [R₁ = ^tBu (1), H (2, 3, 4); R = ^tBu (1, 2), Me (3), Ph (4)] as catalysts in the presence of Al(i‐Bu)₃ and [Ph₃C][B(C₆F₅)₄]. The effect of the concentration of comonomer in the feed and Al/Ti molar ratio on the catalytic activity and molecular weight of the resultant copolymer were investigated. The substituents on the phenyl ring of the ligand affect considerably both the catalytic activity and comonomer incorporation. The 1 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system exhibits the highest catalytic activity and produces copolymers with the highest molecular weight, while the 2 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system gives copolymers with the highest comonomer incorporation under similar conditions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Kinetics and particle nucleation mechanism of St/BA/qBVPBr emulsifier‐free cationic emulsion polymerization

Stable functional cationic latices were prepared by emulsifier‐free emulsion copolymerization of styrene (St) and butyl‐acrylate (BA) with 1‐butyl‐4‐vinylpyridinium bromide (qBVPBr) as functional comonomer and azobis(isobutyramidine hydrochloride) (AIBA) as initiator at (70 ± 1)°C. The influences of the reaction temperature, the initiator concentration, and comonomer concentration on the polymerization conversion (x %), polymerization rate (R_p) of poly(St/BA/qBVPBr) emulsions were investigated. The results indicated that x % and R_p increase with increasing qBVPBr or AIBA concentration and temperature, and R_p can be expressed as R_p = K_p[AIBA]^0.73[qBVPBr]^0.08 (r_AIBA = 0.9968; r_qBVPBr = 0.9946, both r_AIBA and r_qBVPBr are linear correlation coefficient) and the apparent activation energy (E_a) is 47.89 kJ mol^?1. In the absence of emulsifier condition, curves of R_p versus reaction time obeyed the typical behavior characterized by Intervals I, II, and III as similar conventional emulsion polymerization. The formation and growth of poly(St/BA/qBVPBr) latex particles has been studied at different reaction times. The results indicate that N_p decrease gradually with time at the early polymerization stages and then reach a constant value after about 20% conversion, but D_p by photon correlation spectroscopy grow continuously as all polymerization proceed. Both the particle size distribution and molecular weight distribution curves are of bimodal size distribution and indicate the participation of at least two mechanisms of particle formation, namely, homogeneous nucleation in the aqueous phase and micellar nucleation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Ethylene/α‐olefin copolymerization using diphenylcyclopentadienyl‐phenoxytitanium dichloride/Al(iBu)3/[Ph3C][B(C6F5)4] catalyst systems

Copolymerization of ethylene with 1‐octene and 1‐octadecene using constrained geometry catalysts 2‐(3,4‐diphenylcyclopentadienyl)‐4,6‐di‐tert‐butylphenoxytitanium dichloride (1), 2‐(3,4‐diphenylcyclopentadienyl)‐6‐tert‐butylphenoxytitanium dichloride (2), 2‐(3,4‐diphenylcyclopentadienyl)‐6‐methylphenoxytitanium dichloride (3), and 2‐(3,4‐diphenylcyclopentadienyl)‐6‐phenylphenoxytitanium dichloride (4) was studied in the presence of Al(ⁱBu)₃ and [Ph₃C][B(C₆F₅)₄](TIBA/B). The effect of the catalyst structure, comonomer, and reaction conditions on the catalytic activity, comonomer incorporation, and molecular weight of the produced copolymers was also examined. The 1 /TIBA/B catalyst system exhibits high catalytic activity and produces high molecular weight copolymers. The melting temperature and the degree of crystallinity of the copolymers show a decrease with the increase in the comonomer incorporation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Atom transfer radical homo‐ and copolymerization of styrene and methyl acrylate initiated with trichloromethyl‐ terminated poly(vinyl acetate) macroinitiator: A kinetic study

Atom transfer radical bulk copolymerization of styrene (St) and methyl acrylate (MA) initiated with trichloromethyl‐terminated poly(vinyl acetate) macroinitiator was performed in the presence of CuCl/PMDETA as a catalyst system at 90°C. Linear dependence of ln[M]₀/[M] versus time data along with narrow polydispersity of molecular weight distribution revealed that all the homo‐ and copolymerization reactions proceed according to the controlled/living characteristic. To obtain more reliable monomer reactivity ratios, the cumulative average copolymer composition at moderate to high conversion was determined by ¹H‐NMR spectroscopy. Reactivity ratios of St and MA were calculated by the extended Kelen‐Tudos (KT) and Mao‐Huglin (MH) methods to be r_St = 1.018 ± 0.060, r_MA = 0.177 ± 0.025 and r_St = 1.016 ± 0.053, r_MA = 0.179 ± 0.023, respectively, which are in a good agreement with those reported for the conventional free‐radical copolymerization of St and MA. Good agreement between the theoretical and experimental composition drifts in the comonomer mixture and copolymer as a function of the overall monomer conversion were observed, indicating that the reactivity ratios calculated by copolymer composition at the moderate to high conversion are accurate. Instantaneous copolymer composition curve and number‐average sequence length of comonomers in the copolymer indicated that the copolymerization system tends to produce a random copolymer. However, MA‐centered triad distribution results indicate that the spontaneous gradient copolymers can also be obtained when the mole fraction of MA in the initial comonomer mixture is high enough. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Copolymerization of ethylene/α‐olefins over (2‐MeInd)2ZrCl2/MAO and (2‐BzInd)2ZrCl2/MAO systems

Ethylene homopolymerization and ethylene/α‐olefin copolymerization were carried out using unbridged and 2‐alkyl substituted bis(indenyl)zirconium dichloride complexes such as (2‐MeInd)₂ZrCl₂ and (2‐BzInd)₂ZrCl₂. Various concentrations of 1‐hexene, 1‐dodecene, and 1‐octadecene were used in order to find the effect of chain length of α‐olefins on the copolymerization behavior. In ethylene homopolymerization, catalytic activity increased at higher polymerization temperature, and (2‐MeInd)₂ZrCl₂ showed higher activity than (2‐BzInd)₂ZrCl₂. The increase of catalytic activity with addition of comonomer (the synergistic effect) was not observed except in the case of ethylene/1‐hexene copolymerization at 40°C. The monomer reactivity ratios of ethylene increased with the decrease of polymerization temperature, while those of α‐olefin showed the reverse trend. The two catalysts showed similar copolymerization reactivity ratios. (2‐MeInd)₂ZrCl₂ produced the copolymer with higher M_w than (2‐BzInd)₂ZrCl₂. The melting temperature and the crystallinity decreased drastically with the increase of the α‐olefin content but T_m as a function of weight fraction of the α‐olefins showed similar decreasing behavior. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 928–937, 2000     

Different behaviors of metallocene and Ziegler–Natta catalysts in ethylene/1,5‐hexadiene copolymerization

The behaviors of three different catalyst systems, TiCl₄/MgCl₂, Cp₂ZrCl₂ and Cp₂HfCl₂, were investigated in ethylene/1,5‐hexadiene copolymerization. In the Fourier transform infrared spectra of the copolymers, cyclization and branching were detected for 1,5‐hexadiene insertion in the metallocene and Ziegler–Natta systems, respectively. DSC and viscometry analyses results revealed that copolymers with lower T_m and crystallinity and higher molecular weight were obtained with metallocene catalysts. The sequence length distribution of the copolymers was investigated by using the successive self‐nucleation and annealing thermal fractionation technique. The continuous melting endotherms obtained from successive self‐nucleation and annealing analysis were employed to get information about short‐chain branching, the branching dispersity index, comonomer content and lamella thickness in the synthesized copolymers. The results established that metallocene catalysts were much more effective than Ziegler–Natta catalysts in the incorporation of 1,5‐hexadiene in the polyethylene structure. Metallocene‐based copolymers had higher short‐chain branching and comonomer content, narrower branching dispersity index and thinner lamellae. Finally, the tendency of the employed catalysts in the 1,5‐hexadiene incorporation and cyclization reaction was explored via molecular simulation. The energy results demonstrated that, in comparison to Ziegler–Natta, metallocene catalysts have a much higher tendency to 1,5‐hexadiene incorporation and cyclization. © 2018 Society of Chemical Industry     

Copolymerization of butadiene with styrene using a rare‐earth metal compound – dialkylmagnesium – halohydrocarbon catalytic system

Copolymerizations of butadiene (Bd) with styrene (St) were carried out with catalytic systems composed of a rare‐earth compound, Mg(n‐Bu)₂ (di‐n‐butyl magnesium) and halohydrocarbon. Of all the rare earth catalysts examined, Nd(P₅₀₇)₃–Mg(n‐Bu)₂–CHCl₃ showed a high activity in the copolymerization under certain conditions: [Bd] = [St] = 1.8 mol l^?1, [Nd] = 6.0 × 10^?3 mol l^?1, Mg/Nd = 10, Cl/Nd = 10 (molar ratio), ageing for 2 h, copolymerization at 50 °C for 6–20 h. The copolymer of butadiene and styrene obtained has a relatively high styrene content (10–30 mol%), cis‐1,4 content in butadiene unit (85–90%), and molecular weight ([η] = 0.8–1 dL g^?1). Monomer reactivity ratios were estimated to be r_Bd = 36 and r_St = 0.36 in the copolymerization. © 2002 Society of Chemical Industry     

Ethylene/α‐olefin copolymerization by nonbridged (cyclopentadienyl)(aryloxy)titanium(IV) dichloride/AliBu3/Ph3CB(C6F5)4 catalyst systems

A series of nonbridged (cyclopentadienyl) (aryloxy)titanium(IV) complexes of the type, (η⁵‐Cp′)(OAr)TiCl₂ [OAr = O‐2,4,6‐^tBu₃C₆H₂ and Cp′ = Me₅C₅ ( 1 ), Me₄PhC₅ ( 2 ), and 1,2‐Ph₂‐4‐MeC₅H₂ ( 3 )], were prepared and used for the copolymerization of ethylene with α‐olefins (e.g., 1‐hexene, 1‐octene, and 1‐octadecene) in presence of AlⁱBu₃ and Ph₃CB(C₆F₅)₄ (TIBA/B). The effect of the catalyst structure, comonomer, and reaction conditions on the catalytic activity, comonomer incorporation, and molecular weight of the produced copolymers was examined. The substituents on the cyclopentadienyl group of the ligand in 1 – 3 play an important role in the catalytic activity and comonomer incorporation. The 1 /TIBA/B catalyst system exhibits the highest catalytic activity, while the 3 /TIBA/B catalyst system yields copolymers with the highest comonomer incorporation under the same conditions. The reactivity ratio product values are smaller than those by ordinary metallocene type, which indicates that the copolymerization of ethylene with 1‐hexene, 1‐octene, and 1‐octadecene by the 1–3/ TIBA/B catalyst systems does not proceed in a random manner. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Copolymerization of 1‐oxo‐2,6,7‐trioxa‐1‐phorsphabicyclo[2,2,2]oct‐4‐yl methyl acrylate and (10‐oxo‐10‐hydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐yl) methyl acrylate with styrene and their thermal degradation characteristics

Two phosphorus‐containing acrylates of 1‐oxo‐2,6,7‐trioxa‐1‐phorsphabicyclo[2,2,2]oct‐4‐yl methyl acrylate and (10‐oxo‐10‐hydro‐9‐oxa‐10λ⁵‐phosphaphenanthrene‐10‐yl) methyl acrylate were free‐radical‐copolymerized with styrene (St). The r₁ reactivity ratio values (related to the novel acrylates) were 0.342 and 0.225, respectively, and the r₂ reactivity ratio values (related to St) were 0.432 and 0.503, respectively. The thermal stability of the copolymers was tested by thermogravimetric analysis (TGA) in N₂ or air, and the ignitability was tested by measurements of UL‐94 vertical combustion tests and the limiting oxygen index. The results of TGA and combustion tests indicated that the effect of flame retardancy was determined by the nature of the phosphorus‐containing substituent. Compared with the 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide based group, the 1‐oxo‐2,6,7‐trioxa‐1‐phorsphabicyclo[2,2,2]oct‐4‐yl methol based group could enhance the ability of char formation with an antidripping effect. It is concluded that phosphorus‐containing acrylates are potential flame‐retarding monomers for styrenic polymers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Nickel(II) complexes bearing the bis(β‐ketoamino) ligand for the copolymerization of norbornene with a higher 1‐alkene

A novel bis(β‐ketoamino)Ni(II) complex catalyst, Ni{CF₃C(O)CHC[N(naphthyl)]CH₃}₂, was synthesized, and the structure was solved by a single‐crystal X‐ray refraction technique. The copolymerization of norbornene with higher 1‐alkene was carried out in toluene with catalytic systems based on nickel(II) complexes, Ni{RC(O)CHC[N(naphthyl)]CH₃}₂(R?CH₃, CF₃) and B(C₆F₅)₃, and high activity was exhibited by both catalytic systems. The effects of the catalyst structure and comonomer feed content on the polymerization activity and the incorporation rates were investigated. The reactivity ratios were determined to be r_1‐octene = 0.009 and r_norbornene = 13.461 by the Kelen–Tüdõs method for the Ni{CH₃C(O)CHC[N(naphthyl)]CH₃}₂/B(C₆F₅)₃ system. The achieved copolymers were confirmed to be vinyl‐addition copolymers through the analysis of ¹H‐NMR and ¹³C‐NMR. The thermogravimetric analysis results showed that the copolymers exhibited good thermal stability (decomposition temperature, T_dec > 400°C), and the glass‐transition temperature of the copolymers were observed between 215 and 275°C. The copolymers were confirmed to be noncrystalline by wide‐angle X‐ray diffraction analysis and showed good solubility in common organic solvents. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Halogeno‐modified polystyrene: monomer reactivity ratios,thermal behaviour and flammability

Chemical modification based on incorporation of flame retardants into polymer backbones was used in order to reduce flammability of polystyrene (PSt). The halogeno‐substituted styrenes: 4‐chlorostyrene (ClSt), 4‐bromostyrene (BrSt) and 2,3,4,5,6‐pentafluorostyrene (5FSt) were applied as reactive flame retardants. Homo‐ and copolymers of these halogeno‐substituted styrenes and styrene (St) were synthesized with various feed ratios using free radical bulk polymerization with azobisisobutyronitrile as a initiator. This yielded series of (co)polymers with various amounts of included ClSt, BrSt and 5FSt (5–50 mol% of modified St). Copolymer compositions were determined using ¹H NMR spectroscopy. The relative reactivity ratios of the used comonomers were determined by applying conventional linearization methods. The Jaacks (J) method was used for systems including BrSt and ClSt monomers whereas the Fineman–Ross method was additionally used to confirm the values of reactivity ratios of St–5FSt. The reactivity ratios of comonomer pairs obtained from J plots were 0.75 and 0.38 (St–ClSt), 1.65 and 0.46 (St–BrSt), 0.44 and 0.42 (St–5FSt). Glass transition temperature and thermal stability of obtained (co)polymers were determined using differential scanning calorimetry and thermogravimetric analysis (TGA), respectively. The thermal degradation kinetic of PSt, PClSt, PBrSt and P5FSt was studied applying TGA. Kinetic parameters such as thermal decomposition activation energy (E) and frequency factor (A) were estimated using Ozawa and Kissinger models. The resulting activation energies estimated using these two methods were quite close. The values of activation energy (kJ mol^?1) increased in the following order: PClSt (E(O) = 216.1) < PSt (E(O) = 219.9) < PBrSt (E(O) = 224.7) < P5FSt (E(O) = 330.9). A pyrolysis combustion flow calorimeter was applied as a tool for assessing the flammability of the synthesized (co)polymers. © 2014 Society of Chemical Industry     

Polymerization of 1,3‐dienes containing functional groups: 8. Free‐radical polymerization of 2‐triethoxysilyl‐ 1,3‐butadiene

The presence of a bulky substituent at the 2‐position of 1,3‐butadiene derivatives is known to affect the polymerization behavior and microstructure of the resulting polymers. Free‐radical polymerization of 2‐triethoxysilyl‐1,3‐butadiene ( 1 ) was carried out under various conditions, and its polymerization behavior was compared with that of 2‐triethoxymethyl‐ and other silyl‐substituted butadienes. A sticky polymer of high 1,4‐structure ( ) was obtained in moderate yield by 2,2′‐azobisisobutyronitrile (AIBN)‐initiated polymerization. A smaller amount of Diels–Alder dimer was formed compared with the case of other silyl‐substituted butadienes. The rate of polymerization (R_p) was found to be R_p = k[AIBN]^0.5[ 1 ]^1.2, and the overall activation energy for polymerization was determined to be 117 kJ mol^?1. The monomer reactivity ratios in copolymerization with styrene were r ₁ = 2.65 and r_st = 0.26. The glass transition temperature of the polymer of 1 was found to be ?78 °C. Free‐radical polymerization of 1 proceeded smoothly to give the corresponding 1,4‐polydiene. The 1,4‐E content of the polymer was less compared with that of poly(2‐triethoxymethyl‐1,3‐butadiene) and poly(2‐triisopropoxysilyl‐1,3‐butadiene) prepared under similar conditions. Copyright © 2010 Society of Chemical Industry     

Characterization of some perovskite oxides based on YBa2Cu3O7 − x in relation to their use in methanol production

The oxidized and weakly reducible perovskite oxide YBa₂Cu₃O_{7 − x} (YBCO) has been prepared as a catalyst, supported on γ‐Al₂O₃. It was further modified by (i) impregnation with Ru and Pd and (ii) cobalt incorporation via co‐precipitation. All the catalysts were either 20% (w/w) YBCO/γ‐Al₂O₃ or 2% (w/w) Ru, Pd or Co/20% (w/w) YBCO/γ‐Al₂O₃. The catalysts were characterized using temperature programmed reduction (TPR), surface area measurements and X‐ray diffraction (XRD) studies before and after various treatments. They were studied as catalysts in the pressure range 20–50 atmospheres and in the temperature range 523–573 K in an autoclave equipped with a spinning basket catalyst container. The Pd‐, Ru‐ and Co‐modified catalysts gave predominantly methanation products, along with some C₂–C₄ hydrocarbons. However the YBCO/γ‐Al₂O₃ catalyst exhibited significant methanol selectivity at 50 atmospheres and at 523 K X‐ray diffraction studies revealed the presence of Cu(0), Cu(I) and Cu(II) after reduction and the species Cu(0) and Cu(I) are probably essential to CH₃OH production. © 2000 Society of Chemical Industry     

Palladium(II) Complexes of C2‐Bridged Chiral Diphosphines: Application to Enantioselective Carbonyl‐Ene Reactions

(11bR,11′bR)‐4,4′‐(1,2‐Phenylene)bis[4,5‐dihydro‐3H‐dinaphtho[2,1‐c:1′,2′‐e]phosphepin] [abbreviated as (R)‐BINAPHANE], (3R,3′R,4S,4′S,11bS,11′bS)‐4,4′‐bis(1,1‐dimethylethyl)‐4,4′,5,5′‐tetrahydro‐3,3′‐bi‐3H‐dinaphtho[2,1‐c:1′,2′‐e]phosphepin [(S)‐BINAPINE], (1S,1′S,2R,2′R)‐1,1′‐bis(1,1‐dimethylethyl)‐2,2′‐biphospholane [(S,S,R,R)‐TANGPHOS] and (2R,2′R,5R,5′R)‐1,1′‐(1,2‐phenylene)bis[2,5‐bis(1‐methylethyl)phospholane] [(R,R)‐i‐Pr‐DUPHOS] are C₂‐bridged chiral diphosphines that form stable complexes with palladium(II) and platinum(II) containing a five‐membered chelate ring. The Pd(II)‐BINAPHANE catalyst displayed good to excellent enantioselectivities with ee values as high as 99.0% albeit in low yields for the carbonyl‐ene reaction between phenylglyoxal and alkenes. Its Pt(II) counterpart afforded improved yields while retaining satisfactory enantioselectivity. For the carbonyl‐ene reaction between ethyl trifluoropyruvate and alkenes, the Pd(II)‐BINAPHANE catalyst afforded both good yields and extremely high enantioselectivities with ees as high as 99.6%. A comparative study on the Pd(II) catalysts of the four C₂‐bridged chiral diphosphines revealed that Pd(II)‐BINAPHANE afforded the best enantioselectivity. The ee values derived from Pd(II)‐BINAPHANE are much higher than those derived from the other three Pd(II) catalysts. A comparison of the catalyst structures shows that the Pd(II)‐BINAPHANE catalyst is the only one that has two bulky (R)‐binaphthyl groups close to the reaction site. Hence it creates a deep chiral space that can efficiently control the reaction behavior in the carbonyl‐ene reactions resulting in excellent enantioselectivity.     

Chemical composition distribution study in ethylene/1‐hexene copolymerization to produce LLDPE material using MgCl2‐TiCl4‐based Ziegler‐Natta catalysts

The characteristic features of LLDPE polymerization with ZN catalyst are the time drift effect during polymerization and the bending effect when trying to decrease density of the copolymer by adding more comonomer to the polymerization. The time drift in LLDPE polymerization is revealed by a constant decrease of comonomer incorporation during polymerization time. The bending is revealed by difficulties in lowering the density of LLDPE material below the density of 920 kg/m³. With increasing comonomer content during polymerization, the density does not decrease, but the soluble fraction increases. To try to observe if these phenomena are connected, two types of catalysts, SiO₂ supported and precipitated MgCl₂ ZN catalysts, were studied. A short time (10 min) and an extended time (60 min) copolymerization test series where the polymerizations were performed in the presence of a gradually increasing comonomer amount. Both catalysts show a strong bending when density is presented as a function of 1‐hexene both in 10‐ and 60‐min polymerization, indicating no connection between time drift and bending. The density, melting point, and crystallinity results all indicate that both catalysts are making similar copolymer material with identical chemical composition distribution. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Vinyl‐addition copolymerization of norbornene and polar norbornene derivatives using novel bis(β‐ketoamino)Ni(II)/B(C6F5)3/AlEt3 catalytic systems

Copolymerization of norbornene (NBE) and polar norbornene derivatives undergoes vinyl polymerization by using novel catalyst systems formed in situ by combining bis(β‐ketoamino)Ni(II) complexes {Ni[R₁C(O)CHC(NR₃)R₂]₂ (R_l = R₂ = CH₃, R₃ = naphthyl, 1 ; R₁ = R₂ = CH₃, R₃ = C₆H₅, 2 ; R₁ = C₆H₅, R₂ = CH₃, R₃ = naphthyl, 3 ; R_l = R₂ = CH₃, R₃ = 2, 6‐(CH₃)₂C₆H₃, 4 ; R₁ = R₂ = CH₃, R₃ = 2, 6‐′Pr₂C₆H₃ 5 ; R₁ = C₆H₅, R₂ = CH₃, R₃ = 2, 6‐′Pr₂C₆H₃, 6 )} and B(C₆F₅)₃/AlEt₃ in toluene. The 1 /B(C₆F₅)₃/AlEt₃ catalytic system is effective for copolymerization of NBE with NBE OCOCH₃ and NBE CH₂OH, respectively, and copolymerization activity is followed in the order of NBE CH₂OH > NBE OCOCH₃ > NBE CN. The molecular weights of the obtained poly(NBE/NBE CH₂OH) reached 5.97 × 10⁴ to 2.07 × 10⁵ g/mol and the NBE CH₂OH incorporation ratios reached 7.0–55.4 mol % by adjusting the comonomer feedstock composition. The copolymerization of NBE and NBE CH₂OH also depend on catalyst structures and activity of catalyst followed in the order of 2 > 1 > 3 > 5 > 4 > 6 . The molecular weights and NBE CH₂OH incorporation ratios of poly(NBE/NBE CH₂OH) were adjustable to be 1.91–5.37 × 10⁵ g/mol and 9.5–41.1 mol %  OH units by using catalysts 1 – 6 . The achieved copolymers were confirmed to be vinyl‐addition type, noncrystalline and have good thermal stability (T_d = 380–410°C). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Comonomer effects in copolymerization of ethylene and 1‐hexene with MgCl2‐supported Ziegler‐Natta catalysts: New evidences from active center concentration and molecular weight distribution

In this article, comonomer effects in copolymerization of ethylene and 1‐hexene with four MgCl₂‐supported Ziegler‐Natta catalysts using either ethylene or 1‐hexene as the main monomer were investigated. It was found that no matter which monomer was used as the main monomer, the polymerization activity was significantly enhanced by introducing small amount of comonomer. In copolymerization with ethylene as the main monomer, the strength of comonomer effects was much stronger in active centers producing low‐molecular‐weight polymer than those producing high‐molecular‐weight polymer. In copolymerization with 1‐hexene as the main monomer, the number of active centers ([C*]/[Ti]) was determined, and the propagation rate constants (k_p) were calculated. Deconvolution of the polymer molecular weight distribution into Flory components were made to study the active center distribution. Introduction of small amount of ethylene caused marked increase in the number of active centers and decrease in average chain propagation rate constant. Introducing internal electron donor in the catalyst enhanced not only the number of active centers but also the chain propagation rate constant. In copolymerization of 1‐hexene with small amount of ethylene, the internal donor weakened the comonomer effects to some extent and changed the distribution of comonomer effects among different types of active centers. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41264.     

Novel copolyesters containing naphthalene structure III. Copolyesters prepared from 2,6‐dimethyl naphthalate,ethylene glycol,and 2,2‐dialkyl‐1,3‐propanediols

Poly(ethylene naphthalate) (PEN) copolymers were prepared by melt polycondensation of dimethyl naphthalate and excess ethylene glycol with 5–40 mol % (in feed) of 1,3‐propanediol or 2,2‐dialkyl‐1,3‐propanediols, where the dialkyl groups are dimethyl, diethyl, and butyl‐ethyl. No significant depression of reduced specific viscosity was observed. The comonomer contents in the copolymers are considerably higher than those in the feed. The effects of the copolymer composition on the structures of the films were investigated using thermal analyses, density measurements, X‐ray diffraction methods, and other physical tests. The crystallinities and densities of heat‐treated films decreased with increasing content of comonomer and length of alkyl side chain in the comonomer. The glass transition temperature (T_g) and melting temperature (T_m) were decreased by the copolymerization, while an increase in the length of the alkyl side chain hardly affected T_ms of the heat‐treated films. Alkali resistance, moisture resistance, dye ability, and thermal shrinkage were increased by the incorporation of comonomer having an alkyl side chain. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2754–2763, 2001     

Controlled radical alternating copolymerization of N‐phenyl maleimide with ethyl α‐ethylacrylate by reversible addition fragmentation chain‐transfer process

The alternating copolymerization of N‐phenyl maleimide (NPMI) with ethyl α‐ethylacrylate (EEA) by the reversible addition fragmentation chain‐transfer process was investigated. The monomer reactivity ratios were measured and r₁ = 0.19 ± 0.03 for NPMI and r₂ = 0.20 ± 0.04 for EEA. It was found that before about 45% of the comonomer conversion, the molecular weight of the copolymer increased with the conversion, the molecular weight distribution was rather narrow, and the molecular weight of the copolymer approached a constant value, irrespective of the length of the polymerization time. Electronic spin resonance determined that the radical signal disappeared quickly after the conversion of comonomer exceeded 45%, which may be attributed to the coupling termination of the propagating polymer chains with the EEA end with the intermediate radicals when the concentration of comonomers decreased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2376–2382, 2004     

Synthesis and Pharmacological Evaluation of α4β2 Nicotinic Ligands with a 3‐Fluoropyrrolidine Nucleus

Nicotinic acetylcholine receptors (nAChRs) play an important role in many central nervous system disorders such as Alzheimer’s and Parkinson’s diseases, schizophrenia, and mood disorders. The α₄β₂ subtype has emerged as an important target for the early diagnosis and amelioration of Alzheimer’s disease symptoms. Herein we report a new class of α₄β₂ receptor ligands characterized by a basic pyrrolidine nucleus, the basicity of which was properly decreased through the insertion of a fluorine atom at the 3‐position, and a pyridine ring carrying at the 3‐position substituents known to positively affect affinity and selectivity toward the α₄β₂ subtype. Derivatives 3‐(((2S,4R)‐4‐fluoropyrrolidin‐2‐yl)methoxy)‐5‐(phenylethynyl)pyridine ( 11 ) and 3‐((4‐fluorophenyl)ethynyl)‐5‐(((2S,4R)‐4‐fluoropyrrolidin‐2‐yl)methoxy)pyridine ( 12 ) were found to be the most promising ligands identified in this study, showing good affinity and selectivity for the α₄β₂ subtype and physicochemical properties predictive of a relevant central nervous system penetration.