Photocatalytic activation of TiO2 under visible light using Acid Red 44

The activation of TiO₂ photocatalyst for photocatalysis under the visible light using Acid Red 44 (C₁₀H₇N=NC₁₀H₃(SO₃Na)₂OH) is described. Adjustment of the pH enhanced the photocatalytic activation of TiO₂ in the presence of visible light. This confirms that the adsorption of a dye on TiO₂ surface is an important factor in dye-photosensitization. The differences in the photocatalytic activation mechanism under visible irradiated conditions with that of UV irradiated condition are proposed. The dye-sensitized photocatalysis under visible light was applied to the decomposition of phenol, is a toxic chemical used in industry and frequently discharged into water.     

Pt/TiO_2催化二甲醚部分氧化重整制氢

二甲醚是一种理想的氢载体,可用于解决氢的储存和运输。以Pt/TiO_2为部分氧化催化剂,结合Ni/Al_2O_3重整催化剂,考察钛前驱体和焙烧温度对二甲醚部分氧化重整制氢反应的影响。结果表明,以Ti(C4H9O)4为原料制备的TiO_2为金红石相,Ti(SO4)2或Ti O(OH)2为原料制备的TiO_2为锐钛矿相;以Ti(C4H9O)4为原料制备的Pt/TiO_2-E催化剂催化性能略好,转化率接近100%,H2收率约90%,表明金红石相TiO_2负载的Pt催化剂略佳;以Ti(SO4)2为原料制备的Pt/TiO_2-S催化剂500℃焙烧可获得金红石相TiO_2。与Pt/Al_2O_3催化剂相比,Pt/TiO_2催化剂具有更好的催化性能,H2收率超过90%,而Pt/Al_2O_3催化剂H2收率约80%。     

Catalyst deactivation in the gas phase destruction of nitrogen-containing organic compounds using TiO2/UV–VIS

Possible application of the TiO₂/UV–VIS photocatalytic process in the destruction of nitrogen-containing malodorous compounds was evaluated. Pyridine (C₅H₅N), propylamine (C₃H₇NH₂) and diethylamine (C₄H₁₀NH) were photodegraded in the presence and in the absence of oxygen. Degradation of nitrogen-containing organic compounds was confirmed by mass balance taking into consideration NH₄⁺ and NO₃⁻ ions trapped at the TiO₂ surface. Photocatalytic deactivation was observed in all cases. On-line mass spectrometry was used to identify byproducts in the gas phase formed during the degradation process. GC–MS analysis of the dichloromethane-extract of aqueous species leached from the surface of deactivated catalyst, as well as pre-concentration in a Tenax column were used to identify intermediates in the gas phase. These byproducts are considered to be the major ones responsible for deactivation of TiO₂.     

TiO2基催化剂还原CO2研究进展

能源危机和环境污染是当今世界发展面临的两大挑战,如何有效缓解煤、石油等不可再生化石资源过度消耗所引发的能源危机,以及由此造成CO₂过量排放引起的温室效应问题,是当前人类发展亟待解决的重大科学问题之一。基于此,本文综述了近年来以TiO₂为光催化剂,以绿色、清洁的太阳光能催化还原CO₂成低价态含碳燃料(如CH₄、CH₃OH、HCHO、HCOOH、C₂H₅OH等)研究进展。在TiO₂光还原CO₂机理基础上,对元素掺杂、半导体复合与染料敏化、高活性晶面调控、低维纳米结构设计、助催化剂、Z型结构设计和单原子催化等方法来提高光还原CO₂反应效率和选择性进行分析,并指出目前研究存在的关键问题和未来CO₂光还原的发展方向。     

Photocatalytic activity of TiO2/ZSM-5 composites in the presence of SO4 ion

TiO₂/ZSM-5 composites were prepared from SiO₂ of rice husk ash and TiO₂ sol from hydrolyzed TiOSO₄ salt. The combined effect of these two materials greatly enhanced the photocatalytic decolorization of methylene blue dye solution. The instant decolorization of the dye solution in the dark by the composite, TiO₂/ZSM-5 (wt ratio 1:1), resulted from the combination of the adsorption by ZSM-5 zeolite and TiO₂ nano-particles, and of Na₂SO₄ salt adhering to the composite surface. As a strong flocculating agent, the SO₄²⁻ ion caused the precipitation of the dye onto the composite surface which consequently enhanced the photocatalytic decolorization of the dye under UV irradiation. The composite, TiO₂/ZSM-5 (wt ratio 1:5), completely decolorized the methylene blue dye in 2.5 h, giving an equivalent performance to that of TiO₂, P-25 powder.     

Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.     

CO, H2 or C3H8 assisted catalytic combustion of methane over supported LaMnO3 monoliths

The effect of the addition of a second fuel such as CO, C₃H₈ or H₂ on the catalytic combustion of methane was investigated over ceramic monoliths coated with LaMnO₃/La-γAl₂O₃ catalyst. Results of autothermal ignition of different binary fuel mixtures characterised by the same overall heating value show that the presence of a more reactive compound reduces the minimum pre-heating temperature necessary to burn methane. The effect is more pronounced for the addition of CO and very similar for C₃H₈ and H₂. Order of reactivity of the different fuels established in isothermal activity measurements was: CO>H₂≥C₃H₈>CH₄. Under autothermal conditions, nearly complete methane conversion is obtained with catalyst temperatures around 800 °C mainly through heterogeneous reactions, with about 60–70 ppm of unburned CH₄ when pure methane or CO/CH₄ mixtures are used. For H₂/CH₄ and C₃H₈/CH₄ mixtures, emissions of unburned methane are lower, probably due to the proceeding of CH₄ homogeneous oxidation promoted by H and OH radicals generated by propane and hydrogen pyrolysis at such relatively high temperatures.

Finally, a steady state multiplicity is found by decreasing the pre-heating temperature from the ignited state. This occurrence can be successfully employed to pilot the catalytic ignition of methane at temperatures close to compressor discharge or easily achieved in regenerative burners.     

Comparison of photocatalytic efficiencies of TiO2 in suspended and immobilised form for the photocatalytic degradation of nitrobenzenesulfonic acids

The photocatalytic efficiency of TiO₂ immobilised on various supports (glass, cement, red brick and inorganic fibres), using different techniques (sputtering, sol–gel dip-coating, patented method for inorganic fibres), are compared with the photocatalytic efficiency of TiO₂ Degussa P25 in suspension 2 g l⁻¹, for the degradation of 3-nitrobenzenesulfonic acid (3-NBSA) and 4-nitrotoluenesulfonic acid (4-NTSA). In all cases, the fixation of TiO₂ on solid supports appreciably reduces the photocatalytic efficiency. The best results were obtained with TiO₂ on inorganic fibres.     

Preparation, characterization and photocatalytic activity of Si-doped and rare earth-doped TiO2 from mesoporous precursors

Si-doped and rare earth-doped TiO₂ with large specific surface area were prepared by the hydrothermal method and sol–gel route, respectively, using C₁₈H₃₇NH₂ as template. The samples were characterized by XRD, FT-IR, low-temperature N₂ adsorption–desorption measurement, XPS and solid state UV–vis diffuse reflectance spectroscopy. The pore size for Si-doped TiO₂ exhibits both mesoporous and microporous distribution, and that for rare earth-doped TiO₂ exhibits a sharp and narrow distribution in microporous range. The photocatalytic activities were investigated with the degradation of phenol as probe reaction. Compared with pure TiO₂, the conversion of phenol and selectivity to CO₂ increases when adding rare earth elements, and the substitution of Si for Ti in an appropriate range also increases the conversion of phenol.     

Free-radical reactions involved in C1-C3 hydrocarbons interaction with oxide catalysts

Experimental proofs of a free radical mechanism in methane oxidative coupling, with homolytic rupture of the C---H bond are given. High concentrations of free radical sites are produced by mechanical milling of SiO₂. A study of C₁---C₃alkanes interaction with these sites allows to simulate the, processes of alkanes oxidation and oxidative dehydrogenation. The reactivity of ethane and propane is higher than that of methane in accordance with the Polanyi-Semenov rule. Oxidative dehydrogenation of ethane is studied on Cd-containing zeolites. CH₄, C₂H₆ and C₃H₈ oxidative dehydrogenation by O₂ or CO₂ is studied on a MNO/SiO₂ catalyst. The initiation of radical reactions of hydrocarbons on Cl-containing catalysts proceeds via chlorine atoms generation.     

V2O5-WO3-MoO3/TiO2催化剂用于NH3选择性还原减排NOx的性能（英文）

The V2O5-WO3-MoO3/TiO2 honeycomb catalyst was prepared with industrial grade chemicals. The structural and physico-chemical properties were analyzed with X-ray diffraction (XRD), scanning electron micrograph (SEM) and mercury porosimetry. The NOx conversion and durability were investigated on a pilot plant test set under the actual operational conditions of a coal fired boiler. The catalyst monolith had good formability with mass percentage of V:W:Mo:TiO2 :fiber glass= 1:4.5:4.5:72:18. Vanadium, tungsten and molybdenum species were highly dispersed on anatase TiO2 without causing the transformation of anatase TiO2 to rutile by calcining under a current of air at 450℃ for 4.5 h, but there were some degrees of crystal distortion. The catalyst particle sizes were almost uniform with close pile-up and the pore structure was regular with complete macro-pore formation and large specific surface area. The NOx conversion was sensitive to temperature but nearly insensitive to NH3 . The catalyst showed strong adaptability to NOx concentration with activity above 80% in the range of 615-1640 mg·m-3 . Within the range of 720-8640 h continuous operation, the NOx conversion dropped at a rate of about 1% reduction per 600 h.     

The kinetics of phenol decomposition under UV irradiation with and without H2O2 on TiO2, Fe–TiO2 and Fe–C–TiO2 photocatalysts

H₂O₂ used in the photo-Fenton reaction with iron catalyst can accelerate the oxidation of Fe²⁺ to Fe³⁺ under UV irradiation and in the dark (in the so called dark Fenton process). It was proved that conversion of phenol under UV irradiation in the presence of H₂O₂ predominantly produces highly hydrophilic products and catechol, which can accelerate the rate of phenol decomposition. However, while H₂O₂ under UV irradiation could decompose phenol to highly hydrophilic products and dihydroxybenzenes in a very short time, complete mineralization proceeded rather slowly. When H₂O₂ is used for phenol decomposition in the presence of TiO₂ and Fe–TiO₂, decrease of OH radicals formed on the surface of TiO₂ and Fe–TiO₂ has been observed and photodecomposition of phenol is slowed down. In case of phenol decomposition under UV irradiation on Fe–C–TiO₂ photocatalyst in the presence of H₂O₂, marked acceleration of the decomposition rate is observed due to the photo-Fenton reactions: Fe²⁺ is likely oxidized to Fe³⁺, which is then efficiently recycled to Fe²⁺ by the intermediate products formed during phenol decomposition, such as hydroquinone (HQ) and catechol.     

Effect of hydrogen on reaction intermediates in the selective catalytic reduction of NOx by C3H6

Selective catalytic reduction of NO_x by C₃H₆ in the presence of H₂ over Ag/Al₂O₃ was investigated using in situ DRIFTS and GC–MS measurements. The addition of H₂ promoted the partial oxidation of C₃H₆ to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO_x on Ag/Al₂O₃ surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H₂ on the SCR of NO_x by C₃H₆ over Ag/Al₂O₃ catalyst.     

Synthesis of C2H4 by partial oxidation of CH4 over LiCl/NiO

Alkali halide added transition metal oxides produced ethylene selectively in oxidative coupling of methane. The role of alkali halides has been investigated for LiCl-added NiO (LiCl/NiO). In the absence of LiCl the reaction over NiO produced only carbon oxides (CO₂ + CO). However, addition of LiCl drastically improved the yield of C₂ compounds (C₂H₆ + C₂H₄). One of the roles of LiCl is to inhibit the catalytic activity of the host NiO for deep oxidation of CH₄. The reaction catalyzed by the LiCl/NiO proceeds stepwise from CH₄ to C₂H₄ through C₂H₆ (2CH₄ → C₂H₆ → C₂H₄). The study on the oxidation of C₂H₆ over the LiCl/NiO showed that the oxidative dehydrogenation of C₂H₆ to C₂H₄ occurs very selectively, which is the main reason why partial oxidation of CH₄ over LiCl/NiO gives C₂H₄ quite selectively. The other role of LiCl is to prevent the host oxide (NiO) from being reduced by CH₄. The catalyst model under working conditions was suggested to be the NiO covered with molten LiCl. XPS studies suggested that the catalytically active species on the LiCl/NiO is a surface compound oxide which has higher valent nickel cations (Ni^(2+δ)+ or Ni³⁺). The catalyst was deactivated at the temperatures>973 K due to vaporization of LiCl and consumption of chlorine during reaction. The kinetic and CH₄---CD₄ exchange studies suggested that the rate-determining step of the reaction is the abstraction of H from the vibrationally excited methane by the molecular oxygen adsorbed on the surface compound oxide.     

Pd-Rh/TiO2光催化CO2氧化乙烷脱氢研究

采用浸渍还原方法制备Pd-Rh/TiO₂催化剂用于常温光催化CO₂氧化乙烷脱氢制C₂H₄。研究不同Pd/Rh比催化剂的光反应性能，利用XRD、EDX-mapping、TEM、HRTEM、XPS技术表征催化剂表面和电子特性，通过UV-Vis、PL技术考察催化剂光响应性能，采用原位红外光谱技术分析Pd-Rh/TiO₂光催化CO₂氧化乙烷脱氢反应机理。研究表明，Pd-Rh双金属体系可有效提高光反应活性，光照下Pd和Rh金属之间存在内部电子转移的作用，降低了Pd表面的电子云密度，促进光生电子和空穴的分离，同时促进了C₂H₆和CO₂在材料表面的吸附。Ar替换CO₂的对比实验证明，反应中的CO₂消耗H₂，可消除催化剂表面积碳，促进C₂H₄生成。     

纳米N掺杂TiO2的制备及可见光催化活性研究

N-doped TiO2 nanoparticle photocatalysts were prepared through a sol-gel procedure using NH4C1 as the nitrogen source and followed by calcination at certain temperature. Systematic studies for the preparation parameters and their impact on the structure and photocatalytic activity under ultraviolet （UV） and visible light irra-diation were carried out. Multiple techniques （XRD, TEM, DRIF, DSC, and XPS） were commanded to characterize the crystal structures and chemical binding of N-doped TiO2. Its photocatalytic activity was examined by the deg- radation of organic compounds. The catalytic activity of the prepared N-doped TiO2 nanoparticles under visible light （λ〉400nm） irradiation is evidenced by the decomposition of 4-chlorophenol, showing that nitrogen atoms in the N-doped TiO2 nanoparticle catalyst are responsible for the visible light catalytic activity. The N-doped TiO2 nanoparticle catalyst prepared with this modified route exhibits higher catalytic activity under UV irradiation in contrast to TiO2 without N-doping. It is suggested that the doped nitrogen here is located at the interstitial site of TiO2 lattice.     

Promoting effects of CO2 on dehydrogenation of propane over a SiO2-supported Cr2O3 catalyst

The effects of carbon dioxide on the dehydrogenation of C₃H₈ to produce C₃H₆ were investigated over several Cr₂O₃ catalysts supported on Al₂O₃, active carbon and SiO₂. Carbon dioxide exerted promoting effects only on SiO₂-supported Cr₂O₃ catalysts. The promoting effects of carbon dioxide over a Cr₂O₃/SiO₂ catalyst were to enhance the yield of C₃H₆ and to suppress the catalyst deactivation.     

The mechanism of SO2 effect on NO reduction with propene over In2O3/Al2O3 catalyst

An In₂O₃/Al₂O₃ catalyst shows high activity for the selective catalytic reduction of NO with propene in the presence of oxygen. The presence of SO₂ in feed gas suppressed the catalytic activity dramatically at high temperatures; however it was enhanced in the low temperature range of 473–573 K. In TPD and FT-IR studies, the formation of sulfate species on the surface of the catalyst caused an inhibition of NO_X adsorption sites, and the absorbance ability of NO was suppressed by the presence of SO₂, and the amount of ad-NO₃⁻ species decreased obviously. This leads to a decrease of catalytic activity at higher temperatures. However, addition of SO₂ enhanced the formation of carboxylate and formate species, which can explain the promotional effect of SO₂ at low temperature, because active C₃H₆ (partially oxidized C₃H₆) is crucial at low temperature.     

载体对Li-Mn氧化物催化甲烷氧化偶联反应作用

采用浸渍法制备不同金属氧化物载体负载的Li-Mn/MO_x(M=Mg,La,Ti,Si,Zr,Ta)催化剂,对其甲烷氧化偶联反应活性进行评价。结果表明,以TiO_2为载体制备的Li-Mn/TiO_2催化剂具有较高的CH_4转化率和C2烃选择性,C_2烃产率显著提高,金属氧化物TiO_2是Li-Mn复合氧化物的优良催化剂载体。n(Li)∶n(Mn)=1.0∶2.0形成的Li-Mn/TiO_2催化剂具有最高的CH_4转化率和C_2烃选择性,n(C_2H_4)∶n(C_2H_6)的增加有助于提高反应产物中C_2H_4的相对浓度,W元素的添加未能进一步提高Li-Mn/TiO_2催化剂的催化活性。Li-Mn/TiO_2催化剂在n(Li)∶n(Mn)=1.0∶2.0、反应温度775℃、反应压力0.1 MPa、V(CH_4)∶V(O_2)=2.5、空速7 200 m L·(h·g)~(-1)和催化剂用量0.5 g条件下,CH_4转化率达31.9%,C_2选择性达52.7%,表现出最佳催化效果。     

Support-induced promotional effects on the activity of automotive exhaust catalysts 1. The case of oxidation of light hydrocarbons (C2H4)

The kinetics of oxidation of a light hydrocarbon (C₂H₄) were studied on catalysts comprising of combinations of one of three metals, Pt, Pd or Rh supported on five different supports, that is, SiO₂, γ-Al₂O₃, ZrO₂ (8% Y₂O₃), TiO₂ or TiO₂ (W⁶⁺). Significant variation of turnover frequency with the carrier was observed, which cannot be explained by structure sensitivity considerations and is attributed to interactions between the metal crystallites and the carrier. The catalytic activity of these metal-support combinations was investigated over a wide range of partial pressures of ethylene and oxygen. In a separate set of experiments, the kinetics of C₂H₄ oxidation were also investigated on polycrystalline Rh films interfaced with ZrO₂ (8 mol% Y₂O₃) solid electrolyte in a galvanic cell of the type: C₂H₄, O₂, Rh/YSZ/Pt, air, during regular open-circuit conditions as well as under Non-Faradic Electrochemical Modification of Catalytic Activity (NEMCA), that is, closed-circuit conditions. Up to 100-fold increase in catalytic activity was observed by supplying O²⁻ ions to the catalyst surface via positive potential application to the catalyst. The observed kinetic behavior upon increasing catalyst potential parallels qualitatively the observed alteration of turnover frequency with variation of the support of the Rh crystallites.