Fabrication and properties of p-type K doped Zn1−xMgxO thin film

A series of K doped Zn_1−xMg_xO thin films have been prepared by pulsed laser deposition (PLD). Hall-effect measurements indicate that the films exhibit stable p-type behavior with duration of at least six months. The band gap of the K doped Zn_1−xMg_xO films undergoes a blueshift due to the Mg incorporation. However, photoluminescence (PL) results reveal that the crystallinity decreased with the increasing of Mg content. The fabricated K doped p-type Zn_0.95Mg_0.05O thin film exhibits good electrical properties, with resistivity of 15.21 Ω cm and hole concentration of 5.54 × 10¹⁸ cm⁻³. Furthermore, a simple ZnO-based p-n heterojunction was prepared by deposition of a K-doped p-type Zn_0.95Mg_0.05O layer on Ga-doped n-type ZnO thin film with low resistivity. The p-n diode heterostructure exhibits typical rectification behavior of p-n junctions.     

Growth and characterization of chemical bath deposited Cd1−xZnxS thin films

Cd_1−xZn_xS (0 ≤ x ≤ 1) thin films have been deposited by chemical bath deposition method on glass substrates from aqueous solution containing cadmium acetate, zinc acetate and thiourea at 80 ± 5 °C and after annealed at 350 °C. The structural, morphological, compositional and optical properties of the deposited Cd_1−xZn_xS thin films have been studied by X-ray diffractometer, scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), photoluminescence (PL) and UV-vis spectrophotometer, respectively. X-ray diffraction analysis shows that for x < 0.8, the crystal structure of Cd_1−xZn_xS thin films was hexagonal structure. For x > 0.6, however, the Cd_1−xZn_xS films were grown with cubic structure. Annealing the samples at 350 °C in air for 45 min resulted in increase in intensity as well as a shift towards lower scattering angles. The parameters such as crystallite size, strain, dislocation density and texture coefficient are calculated from X-ray diffraction studies. SEM studies reveal the formation of Cd_1−xZn_xS films with uniformly distributed grains over the entire surface of the substrate. The EDX analysis shows the content of atomic percentage. Optical method was used to determine the band gap of the films. The photoluminescence spectra of films have been studied and the results are discussed.     

Preparation, structure and electrical conductivity of the pyrochlore-type phase Sm2Zr2O7 codoped with bivalent magnesium and trivalent dysprosium cations

The pyrochlore-type phases with the compositions of SmDy_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.20) have been prepared by pressureless-sintering method for the first time as possible solid electrolytes. The structure and electrical conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics have been studied by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance spectroscopy measurements. SmDy_1−xMg_xZr₂O_7−x/2 (x = 0, 0.05, 0.10) ceramics exhibit a single phase of pyrochlore-type structure, and SmDy_1−xMg_xZr₂O_7−x/2 (x = 0.15, 0.20) ceramics consist of pyrochlore phase and a small amount of the second phase magnesia. The total conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics obeys the Arrhenius relation, and the total conductivity of each composition increases with increasing temperature from 673 to 1173 K. SmDy_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest total conductivity value is about 8 × 10⁻³ S cm⁻¹ at 1173 K for SmDy_1−xMg_xZr₂O_7−x/2 ceramics.     

Characterization and blood compatibility of TiCxN1 − x hard coating prepared by plasma electrolytic carbonitriding

A novel technique to form Ti(C, N) on titanium, named as plasma electrolytic carbonitriding (PEC/N) on cathode was successful used to prepare TiC_xN_1 − x coating. The structure, composition and morphology of the coating were characterized by XRD, XPS and SEM, respectively. The results indicated that TiC_0.3N_0.7 as a new species appears on the surface of the titanium plate, and the thickness of the coating with porous surface morphology increases with the treated time. The blood compatibility of the TiC_0.3N_0.7 coating was evaluated by haemolysis ratios, dynamic blood clotting test, plasma recalcification time and platelet adhesion. The results indicated that the blood compatibility of the plasma-treated titanium with TiC_xN_1 − x coating is significantly improved as compared to the original titanium. Additionally, the results derived from measurements of hardness and corrosion indicated that the coating has excellent mechanical and corrosion-resistant properties.     

Structural, morphological and optical properties of Bi2−xSbxSe3 thin films grown by electrodeposition

Ternary single-phase Bi_2−xSb_xSe₃ alloy thin films were synthesized onto Au(1 1 1) substrates from an aqueous solution containing Bi(NO₃)₃, SbCl₃, and SeO₂ at room temperature for the first time via the electrodeposition technique. The electrodeposition of the thin films was studied using cyclic voltammetry, compositional, structural, optical measurements and surface morphology. It was found that the thin films with different stoichiometry can be obtained by controlling the electrolyte composition. The as-deposited films were crystallized in the preferential orientation along the (0 1 5) plane. The SEM investigations show that the film growth proceeds via nucleation, growth of film layer and formation of spherical particles on the film layer. The particle size and shape of Bi_2−xSb_xSe₃ films could be changed by tuning the electrolyte composition. The optical absorption spectra suggest that the band gap of this alloy varied from 0.24 to 0.38 eV with increasing Sb content from x = 0 to x = 0.2.     

Structural, elastic and electronic properties of Mg(Cu1−xZnx)2 alloys calculated by first-principles

The structural, elastic and electronic properties of Mg(Cu_1−xZn_x)₂ alloys (x = 0, 0.25, 0.5,and 0.75) were investigated by means of first-principle calculations within the framework of density functional theory (DFT). The calculation results demonstrated that the partial substitution of Cu with Zn in MgCu₂ leaded to an increase of lattice constants, and the optimized structural parameters were in very good agreement with the available experimental values. From energetic point of view, it was found that with increase of Zn content the structural stability of Mg(Cu_1−xZn_x)₂ alloys decreased apparently. The single-crystal elastic constants were obtained by computing total energy as a function of strain, and then the bulk modulus B, shear modulus G, Young's modulus Y and Poisson's ratio ν of polycrystalline aggregates were derived. The calculated results showed that among the Mg(Cu_1−xZn_x)₂ alloys, MgCuZn exhibited the largest stiffness, while Mg₂Cu₃Zn showed the best ductility. Finally, the electronic density of states (DOSs) and charge density distribution were further studied and discussed.     

Relationships between Zr substitution for Ti and microwave dielectric properties in Mg(ZrxTi1−x)O3 ceramics

The influence of Zr substitution for Ti on the microwave dielectric properties and microstructures of the Mg(Zr_xTi_1−x)O₃(MZ_xT) (0.01 ≤ x ≤ 0.3) ceramics was investigated. The quality factors of Mg(Zr_xTi_1−x)O₃ ceramics with x = 0.01-0.05 were improved because the solid solution of a small amount of Zr⁴⁺ substitution in the B-site could increase density and grain size. An excess of Zr⁴⁺ resulted in the formation of a great deal of secondary phase that declined the microwave dielectric properties of MZ_xT ceramics. The temperature coefficient of resonant frequency (τ_f) of Mg(Zr_xTi_1−x)O₃ ceramics slightly increased with increasing Zr content, and the variation in τ_f was attributed to the formation of secondary phases.     

Structural, optical and electrical properties of Mg-doped CuCrO2 thin films by sol-gel processing

CuCr_1−xMg_xO₂ (x = 0, 0.03, 0.05, 0.07) thin films were prepared on sapphire substrates by sol-gel processing. The effect of Mg concentrations on the structural, morphological, electrical and optical properties was investigated. Highly transparent ≧70% Mg-doped CuCrO₂ thin films with p-type conduction and semiconductor behavior were obtained. The microstructure of the systems was characterized by scanning electron microscopy and the roughness increased as the content of Mg increased. The photoluminescence spectra results indicated that it had a green luminescent emission peak at the 530 nm. In this paper, CuCr_0.95Mg_0.05O₂ film has the lowest resistivity of 7.34 Ω cm with direct band gap of 3.11 eV. In order to investigate the conduction mechanism, the energy band of the CuCrO₂ films is constructed based on the grain-boundary scattering.     

Thermoelectric properties of Cu1−xPtxFeO2 (0.0 ≤ x ≤ 0.05) delafossite-type transition oxide

The samples of Cu_1−xPt_xFeO₂ (0 ≤ x ≤ 0.05) delafossite were synthesized by solid state reaction method for studying thermoelectric properties. The properties of Seebeck coefficient, electrical conductivity and thermal conductivity were measured in the high temperature ranging from 300 to 960 K. The results of Seebeck coefficient, electrical conductivity and power factor were increased with increasing Pt substitution and temperature. The thermal conductivity was decreased from 5.8 to 3.5 W/mK with increasing the temperature from 300 to 960 K. An important results, the highest value of power factor and ZT is 2.0 × 10⁻⁴ W/mK² and 0.05, respectively, for x = 0.05 at 960 K.     

Electrical properties of binder-free thick film BaYxBi1−xO3 NTC thermistors

The microstructure and electrical properties of BaY_xBi_1−xO₃ thick film negative temperature coefficient thermistors, fabricated by screen printing, were investigated. The sintered thick films were the single-phase solid solutions of the BaY_xBi_1−xO₃ compounds with a monoclinic structure. The added Y₂O₃ led to a significant decrease in the grain size of the thermistors. The resistivity and coefficient of temperature sensitivity for the BaY_xBi_1−xO₃ (0 ≤ x ≤ 0.15) thick film NTC thermistors decreased first with increasing x in the range of x < 0.04 and then increased with further increase in x.     

Effect of Ag-doping on crystal structure and high temperature thermoelectric properties of c-axis oriented Ca3Co4O9 thin films by pulsed laser deposition

Ag-doped Ca₃Co₄O₉ thin films with nominal composition of Ca_3−xAg_xCo₄O₉ (x = 0∼0.4) have been prepared on sapphire (0 0 0 1) substrates by pulsed laser deposition (PLD). Structural characterizations and surface chemical states analysis have shown that Ag substitution for Ca in the thin films can be achieved with doping amount of x ≤ 0.15; while x > 0.15, excessive Ag was found as isolated and metallic species, resulting in composite structure. Based on the perfect c-axis orientation of the thin films, Ag-doping has been found to facilitate a remarkable decrease in the in-plane electrical resistivity. However, if doped beyond the substitution limit, excessive Ag was observed to severely reduce the Seebeck coefficient. Through carrier concentration adjustment by Ag-substitution, power factor of the Ag-Ca₃Co₄O₉ thin films could reach 0.73 mW m⁻¹ K⁻² at around 700 K, which was about 16% higher than that of the pure Ca₃Co₄O₉ thin film.     

Thermoelectric properties of Bi2SexTe3−x prepared by Bridgman method

Bi₂Se_xTe_3−x crystals with various x values were grown by Bridgman method. The electrical conductivity, σ, was found to decrease with increasing Se content. The highest σ of 1.6 × 10⁵ S m⁻¹ at room temperature was reached at x = 0.12 with a growth rate of 0.8 mm h⁻¹. The Seebeck coefficient, S, was less dependent on Se content, all with positive values showing p-type characteristics, and the highest S was measured to be 240 μV K⁻¹ at x = 0.24. The lowest thermal conductivity, κ, was 0.7 W m⁻¹ K⁻¹ at x = 0.36. The electronic part of κ, κ_el, showed a decrease with increasing Se content, which implies that the hole concentration as the main carriers was reduced by the addition of Se. The highest dimensionless figure of merit, ZT, at room temperature was 1.2 at x = 0.36, which is attributed to the combination of a rather high electrical conductivity and Seebeck coefficient and low thermal conductivity.     

CuIn1−xAlxS2 thin films prepared by sulfurization of metallic precursors

CuIn_1−xAl_xS₂ thin films (x = 0, 0.09, 0.27, 0.46, 0.64, 0.82 and 1) with thicknesses of approximately 1 μm were formed by the sulfurization of DC sputtered Cu-In-Al precursors. All samples were sulfurized in a graphite container for 90 min at 650 °C in a 150 kPa Ar + S atmosphere. Final films were studied via X-ray diffraction (XRD), scanning electron microscopy (SEM) and micro-Raman spectroscopy. It was found that all samples were polycrystalline in nature and their lattice parameters varied slightly nonlinearly from {a = 5.49 Å, c = 11.02 Å} for CuInS₂ to {a = 5.30 Å, c = 10.36 Å} for CuAlS₂. No unwanted phases such as Cu_2−xS or others were observed. Raman were recorded at a room temperature and the most intensive and dominant A₁ phonon frequency varied nonlinearly from 294 cm⁻¹ (CuInS₂) to 314 cm⁻¹ (CuAlS₂).     

Power factor enhancement in Zn-doped Na0.8CoO2

The thermoelectric properties of Na_0.8Zn_xCo_1−xO₂/(ZnO)_y (x ≤ 0.01, 0 ≤ y ≤ 0.14) have been systematically investigated. The results suggest that doping divalent Zn ions within solubility limit x^* ∼ 0.01 leads to simultaneous reduction in resistivity and enhancement of thermopower. Analysis of the results show that the reduction of resistivity may be attributed to improved mobility of carriers, while the enhancement of thermopower may originate from the geometric relaxation of distorted CoO₆ octahedra caused by partial Zn substitution, leading to a narrower band width in the strongly correlated environment, consequently resulting in a remarkable 20% improvement in power factor.     

Low temperature sintering and microwave dielectric properties of (Mg0.7Zn0.3)0.95Co0.05TiO3 ceramics with BaCu(B2O5) additions

The effects of BaCu(B₂O₅) additives on the sintering temperature and microwave dielectric properties of (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were investigated. The (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were not able to be sintered below 1000 °C. However, when BaCu(B₂O₅) were added, they were sintered below 1000 °C and had the good microwave dielectric properties. It was suggested that a liquid phase with the composition of BaCu(B₂O₅) was formed during the sintering and assisted the densification of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics at low temperature. BaCu(B₂O₅) powders were produced and used to reduce the sintering temperature of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics. Good microwave dielectric properties of Q × f = 35,000 GHz, ?_r = 18.5.0 and τ_f = −51 ppm/°C were obtained for the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics containing 7 wt.% mol% BaCu(B₂O₅) sintered at 950 °C for 4 h.     

Preparation and characterization of La1−xKxFeO3 (x = 0-1) by self-propagating high-temperature synthesis for use as soot combustion catalyst

This paper proposes La_1−xK_xFeO₃ prepared by self-propagating high-temperature synthesis (SHS) as an alternative to platinum catalysts for promoting diesel soot combustion. The catalytic property of eleven products SHSed with different substitution ratios of potassium (x = 0-1) was experimentally evaluated using a thermobalance. In the mass loss curves of the product, T₅₀ was defined as the temperature at which the weight of the reference soot decreases to half its initial weight. The BET specific surface area of SHSed La_1−xK_xFeO₃ depended on x strongly. All the products showed good oxidation catalytic activity. Despite having the smallest surface area (0.11 m²/g) among the obtained products, La_0.9K_0.1FeO₃ (x = 0.1) was found to be the best catalyst with the lowest T₅₀ (442 °C). T₅₀ of La_1−xK_xFeO₃ decreased with increasing x for x > 0.2. The products with x = 0.6 and 0.8 were the second-best catalysts in terms of their T₅₀. Moreover, average apparent activation energy of La_0.9K_0.1FeO₃ (x = 0.1) calculated by Friedman method using TG was as much as 61 kJ/mol lower than that of Pt/Al₂O₃ catalyst. In conclusion, potassium-substituted SHSed La_1−xK_xFeO₃ can be used as an alternative to Pt/Al₂O₃ for soot combustion.     

Effect of the impurity LixNi1−xO on the electrochemical properties of 5 V cathode material LiNi0.5Mn1.5O4

The formation of impurity Li_xNi_1−xO when synthesizing spinel LiNi_0.5Mn_1.5O₄ using solid state reaction method, and its influence on the electrochemical properties of product LiNi_0.5Mn_1.5O₄ were studied. The secondary phase Li_xNi_1−xO emerges at high temperature due to oxygen deficiency for LiNi_0.5Mn_1.5O₄ and partial reduction of Mn⁴⁺ to Mn³⁺ in LiNi_0.5Mn_1.5O₄. Annealing process can diminish oxygen deficiency and inhibit impurity Li_xNi_1−xO. The impurity reduces the specific capacity of product, but it does not have obvious negative effect on cycle performance of product. The capacity of LiNi_0.5Mn_1.5O₄ that contains Li_xNi_1−xO can deliver about 120 mAh g⁻¹.     

Magnetomechanical properties of epoxy-bonded Sm1−xNdxFe1.55 (0 ≤ x ≤ 0.56) pseudo-1-3 magnetostrictive particulate composites

Pseudo-1-3 magnetostrictive particulate composites consisting of light rare earth (Sm and Nd)-based magnetostrictive Sm_1−xNd_xFe_1.55 particles with the Nd content x of 0-0.56 and randomly distributed sizes of 10-180 μm embedded and aligned in a passive epoxy matrix are fabricated using the particulate volume fraction of 0.5. The quasistatic magnetomechanical properties of the composites are investigated and the results are compared with their monolithic alloys for various x. The composites exhibit similar qualitative trends in properties with the alloys for all x. The Sm_0.92Nd_0.08Fe_1.55 composite shows a large unsaturated magnetostriction λ of −530 ppm at 500 kA/m and a high piezomagnetic coefficient d₃₃ of −2.0 nm/A at 100 kA/m as a result of the magnetocrystalline anisotropy compensation between Sm³⁺ and Nd³⁺ ions in the Sm_0.92Nd_0.08Fe_1.55 alloy.     

Structural and dielectric properties of Bi2Zn2/3Nb4/3O7 thin films prepared by pulsed laser deposition at low temperature for embedded capacitor applications

Bi₂Zn_2/3Nb_4/3O₇ thin films were deposited on Pt/TiO₂/SiO₂/Si(1 0 0) substrates at a room temperature under the oxygen pressure of 1-10 Pa by pulsed laser deposition. Bi₂Zn_2/3Nb_4/3O₇ thin films were then post-annealed below 200 °C in a rapid thermal process furnace in air for 20 min. The dielectric and leakage current properties of Bi₂Zn_2/3Nb_4/3O₇ thin films are strongly influenced by the oxygen pressure during deposition and the post-annealing temperature. Bi₂Zn_2/3Nb_4/3O₇ thin films deposited under 1 Pa oxygen pressure and then post-annealed at a temperature of 150 °C show uniform surface morphologies. Dielectric constant and loss tangent are 57 and 0.005 at 10 kHz, respectively. The high resolution TEM image and the electron diffraction pattern show that nano crystallites exist in the amorphous thin film, which may be the origin of high dielectric constant in the Bi₂Zn_2/3Nb_4/3O₇ thin films deposited at low temperatures. Moreover, Bi₂Zn_2/3Nb_4/3O₇ thin film exhibits the excellent leakage current characteristics with a high breakdown strength and the leakage current density is approximately 1 × 10⁻⁷ A/cm² at an applied bias field of 300 kV/cm. Bi₂Zn_2/3Nb_4/3O₇ thin films are potential materials for embedded capacitor applications.     

A study of structural, optical and magnetic properties of Zn0.97−xCuxCr0.03O diluted magnetic semiconductors

A set of Zn_0.97−xCu_xCr_0.03O (0 ≤ x ≤ 0.03) samples has been synthesized by the sol-gel method. The structural, optical and magnetic properties of the samples were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and vibrating sample magnetometer (VSM). With Cu doping concentration increasing up to 2 at%, the XRD results showed that all diffraction peaks corresponded to wurtzite structure of ZnO, but for Zn_0.94Cu_0.03Cr_0.03O, the secondary phase of Cu emerged. PL measurements showed that Zn_0.97−xCu_xCr_0.03O powders and pure ZnO with the Cu concentration varied from 0.00 to 0.02 exhibited obvious blue shift; the green emission peak could be effectively enhanced with the increase of the Cu concentration. Magnetic measurements indicated that room-temperature ferromagnetism of Zn_0.97−xCu_xCr_0.03O was an intrinsic property when Cu concentration was less than 0.02. The saturation magnetization of Zn_0.97−xCu_xCr_0.03O (x = 0, 0.01, 0.02) increased with the increase of the Cu concentration.