Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Quasi‐active power factor correction on flyback‐based dc/dc converter

This paper presents a novel input current shaper based on a quasi‐active power factor correction (PFC) scheme. In this method, high power factor and low harmonic content are achieved by providing an auxiliary PFC circuit with a driving voltage which is derived from a third winding of the transformer of a cascaded dc/dc flyback converter. It eliminates the use of active switch and control circuit for PFC. The auxiliary winding provides a controlled voltage‐boost function for bulk capacitor without inducing a dead angle in the line current. Since the dc/dc converter operates at high switching frequency, the driving voltage is also of high switching frequency, which results in reducing the size of the magnetic components. Operating principles, analysis and experimental results of the proposed method are presented. Copyright © 2011 John Wiley & Sons, Ltd.     

An active‐clamping zero‐voltage‐switching flyback converter with integrated transformer

This paper proposes an active‐clamping flyback converter using an integrated transformer. The proposed converter is composed of two active‐clamp flyback converters. The presented converter can balance the total load current between secondary sides of two transformers so that the rectifier diode conduction loss is reduced. Also, the main switch of one converter is the auxiliary switch for the other converter, so that only two switches are required and both can achieve zero‐voltage‐switching operation. The two transformers are integrated into one magnetic core; therefore, the volume and copper loss of transformer can be reduced. Detailed analysis and design of this integrated magnetic active‐clamping flyback converter are described. Experimental results are recorded for a prototype converter with an AC input voltage ranging from 85 to 135 V, an output voltage of 24 V and an output current of 5 A, operating at a switching frequency of 100 kHz. Copyright © 2014 John Wiley & Sons, Ltd.     

A novel prototype of auxiliary edge resonant bridge leg link snubber‐assisted soft‐switching sine‐wave PWM inverter

This paper proposes a new circuit topology of the three‐phase soft‐switching PWM inverter and PFC converter using IGBT power modules, which has the improved active auxiliary switch and edge resonant bridge leg‐commutation‐link soft‐switching snubber circuit with pulse current regenerative feedback loop as compared with the typical auxiliary resonant pole snubber discussed previously. This three‐phase soft‐switching PWM double converter is more suitable and acceptable for a large‐capacity uninterruptible power supply, PFC converter, utility‐interactive bidirectional converter, and so forth. In this paper, the soft‐switching operation and optimum circuit design of the novel type active auxiliary edge resonant bridge leg commutation link snubber treated here are described for high‐power applications. Both the main active power switches and the auxiliary active power switches achieve soft switching under the principles of ZVS or ZCS in this three‐phase inverter switching. This three‐phase soft‐switching commutation scheme can effectively minimize the switching surge‐related electromagnetic noise and the switching power losses of the power semiconductor devices; IGBTs and modules used here. This three‐phase inverter and rectifier coupled double converter system does not need any sensing circuit and its peripheral logic control circuits to detect the voltage or the current and does not require any unwanted chemical electrolytic capacitor to make the neutral point of the DC power supply voltage source. The performances of this power conditioner are proved on the basis of the experimental and simulation results. Because the power semiconductor switches (IGBT module packages) have a trade‐off relation in the switching fall time and tail current interval characteristics as well as the conductive saturation voltage characteristics, this three‐phase soft‐switching PWM double converter can improve actual efficiency in the output power ranges with a trench gate controlled MOS power semiconductor device which is much improved regarding low saturation voltage. The effectiveness of this is verified from a practical point of view. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 64–76, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20207     

A soft‐switching high step‐up DC‐DC converter with a single magnetic component

A soft‐switching high step‐up DC‐DC converter with a single magnetic component is presented in this paper. The proposed converter can provide high voltage gain with a relatively low turn ratio of a transformer. Voltage doubler structure is selected for the output stage. Due to this structure, the voltage gain can be increased, and the voltage stresses of output diodes are clamped as the output voltage. Moreover, the output diode currents are controlled by a leakage inductance of a transformer, and the reverse‐recovery loss of the output diodes is significantly reduced. Two power switches in the proposed converter can operate with soft‐switching due to the reflected secondary current. The voltages across the power switches are confined to the clamping capacitor voltage. Steady‐state analysis, simulation, and experimental results for the proposed converter are presented to validate the feasibility and the performance of the proposed converter. Copyright © 2012 John Wiley & Sons, Ltd.     

Analysis and implementation of a high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter

A high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter with ripple‐free input current is presented. In the presented converter, the ripple‐free boost cell provides ripple‐free input current and zero‐voltage switching of power switches. The resonant flyback cell provides zero‐voltage switching of power switches and zero‐current switching of the output diode. Also, it has a simple output stage. The proposed converter achieves high efficiency because of the reduction of the switching losses of the power switches and the output diode. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed and its experimental results are presented for validation. Copyright © 2011 John Wiley & Sons, Ltd.     

Analysis and design of a two‐transformer active‐clamping forward converter with parallel‐connected current doubler rectifiers

A new two‐transformer active‐clamping forward converter with parallel‐connected current doubler rectifiers (CDRs) is proposed in this paper. The presented DC–DC converter is mainly composed of two active‐clamping forward converters with secondary CDRs. Only two switches are required and each one is the auxiliary switch for the other. The circuit complexity and cost are thus reduced. The leakage inductance of the transformer or an additional resonant inductance is employed to achieve zero‐voltage‐switching (ZVS) during the dead times. Two CDRs at the secondary side are connected in parallel to reduce the current stresses of the secondary windings and the ripple current at the output side. Accordingly, the smaller output chokes and capacitors decrease the converter volume and increase the power density. Detailed analysis and design of the presented two‐transformer active‐clamping forward converter are described. Experimental results are recorded for a prototype converter with a DC input voltage of 130??180V, an output voltage of 5 V and an output current of 40 A, operating at a switching frequency of 100 kHz. Copyright © 2010 John Wiley & Sons, Ltd.     

Series resonant high‐voltage DC–DC converter with reduced component count

This paper proposes a novel zero‐current‐switching series resonant high‐voltage DC–DC converter with reduced component count. The series resonant inverter in the proposed topology has two power switches (insulated‐gate bipolar transistors, IGBTs), two resonant capacitors, and only one high‐voltage transformer (HVT) with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. The leakage inductances of the transformer's primary windings together with the resonant capacitors form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with interleaved half switching cycle. The secondary winding of the HVT is connected to a bridge rectifier circuit to rectify the secondary voltage. The converter operates in the discontinuous conduction mode (DCM) and its output voltage is regulated by pulse frequency modulation. Therefore, all the power switches turn on and off at the zero‐current switching condition. The main features of the proposed converter are its lower core loss, lower cost, and smaller size compared to previously proposed double series resonant high voltage DC–DC converters. The experimental results of a 130‐W prototype of the proposed converter are presented. The results confirm the excellent operation and performance of the converter. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Design of a ZVS PWM DC–DC converter for high gain applications

In this paper, a pulse width modulation DC‐DC converter with high step‐up voltage gain is proposed. The proposed converter achieves high step‐up voltage gain with appropriate duty ratio, coupled inductor, and voltage multiplier technique. The energy stored in the leakage inductor of the coupled inductor can be recycled in the proposed converter. Moreover, because both main and auxiliary switches can be turned on with zero‐voltage switching, switching loss can be reduced by soft‐switching technique. So the overall conversion efficiency is improved significantly. The theoretical steady‐state analyses and the operating principles of the proposed converter are discussed in detail for both continuous conduction mode and discontinuous conduction mode. Finally, a laboratory prototype circuit of the proposed converter is implemented to verify the performance of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd.     

Two‐switch flyback PWM DC‐DC converter in continuous‐conduction mode

The two‐switch flyback DC‐DC converter is an extended version of the conventional single‐switch flyback converter. An additional switch and two clamping diodes serve as a simple, but an effective way to limit the switch overvoltages, which occur in the conventional single‐switch flyback converter due to the ringing of the resonant circuit formed by the transformer leakage inductance and the transistor output capacitance. The clamping diodes in the two‐switch flyback topology clamp the maximum voltage across each switch equal to the DC input voltage. This paper presents a detailed steady‐state analysis and design procedure of the diode‐clamped two‐switch flyback converter operated in continuous‐conduction mode (CCM). The power loss in each component of the two‐switch flyback converter is compared with those of the single‐switch flyback converters with and without RCD clamp, and is presented in a tabular form. The two‐switch flyback converter was bread‐boarded to validate the theoretical analysis. Experimental results from a 10 V/30 W, 100 kHz laboratory prototype verified that the maximum switch voltage is limited to the DC input voltage. Copyright © 2010 John Wiley & Sons, Ltd.     

Analysis,design and implementation of a high‐voltage gain DC‐DC converter

An interleaved DC‐DC converter with soft switching technique is presented. There are two converter modules in the adopted circuit to share the load power. Since the interleaved pulse‐width modulation (PWM) is adopted to control two circuit modules, the ripple currents at input and output sides are naturally reduced. Therefore the input and output capacitances can be reduced. In each circuit module, a conventional boost converter and a voltage doubler configuration with a coupled inductor are connected in series at the output side to achieve high step‐up voltage conversion ratio. Active snubber connected in parallel with boost inductor is adopted to limit voltage stress on active switch and to release the energy stored in the leakage and magnetizing inductances. Since asymmetrical PWM is used to control active switches, the leakage inductance and output capacitance of active switches are resonant in the transition interval. Thus, both active switches can be turned on at zero voltage switching. The resonant inductance and output capacitances at the secondary side of transformer are resonant to achieve zero current switching turn‐off for rectifier diodes. Therefore, the reverse recovery losses of fast recovery diodes are reduced. Finally, experiments based on a laboratory prototype rated at 400 W are presented to verify the effectiveness of the proposed converter. Copyright © 2012 John Wiley & Sons, Ltd.     

Hybrid DC–DC converter with high efficiency,wide ZVS range,and less output inductance

In this paper, a new soft switching direct current (DC)–DC converter with low circulating current, wide zero voltage switching range, and reduced output inductor is presented for electric vehicle or plug‐in hybrid electric vehicle battery charger application. The proposed high‐frequency link DC–DC converter includes two resonant circuits and one full‐bridge phase‐shift pulse‐width modulation circuit with shared power switches in leading and lagging legs. Series resonant converters are operated at fixed switching frequency to extend the zero voltage switching range of power switches. Passive snubber circuit using one clamp capacitor and two rectifier diodes at the secondary side is adopted to reduce the primary current of full‐bridge converter to zero during the freewheeling interval. Hence, the circulating current on the primary side is eliminated in the proposed converter. In the same time, the voltage across the output inductor is also decreased so that the output inductance can be reduced compared with the output inductance in conventional full‐bridge converter. Finally, experiments are presented for a 1.33‐kW prototype circuit converting 380 V input to an output voltage of 300–420 V/3.5 A for battery charger applications. Copyright © 2015 John Wiley & Sons, Ltd.     

LLC resonant DC–DC converter with series‐connected primary windings of transformer

This paper proposes a zero‐voltage switching (ZVS) LLC resonant step up DC–DC converter with series‐connected primary windings of the transformer. The series resonant inverter in the proposed topology has two power switches (MOSFETs), two resonant capacitors, two resonant inductors, and only one transformer with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. Resonant capacitors and inductors along with the primary windings of the transformer form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with an interleaved half switching cycle. The secondary winding of transformer is connected to a bridge rectifier circuit to rectify the output voltage. The converter operates within a narrow frequency range below the resonance frequency to achieve ZVS, and its output power is regulated by pulse frequency modulation. The converter has lower conduction and switching losses and therefore higher efficiency. The experimental results of a 500‐W prototype of proposed converter are presented. The results confirm the good operation and performance of the converter. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Two‐switch flyback PWM DC–DC converter in discontinuous‐conduction mode

The two‐switch flyback DC–DC converter is an extended version of the conventional single‐switch flyback converter. An additional switch and two clamping diodes serve as a simple, but an effective way to limit the switch overvoltages, which occur in the conventional single‐switch flyback converter due to the ringing of the resonant circuit formed by the transformer leakage inductance and the transistor output capacitance. The clamping diodes in the two‐switch flyback topology clamp the maximum voltage across each switch equal to the DC input voltage. This paper presents a detailed analysis and design procedure of the diode‐clamped two‐switch flyback converter operated in discontinuous‐conduction mode (DCM). A comparison of power losses of the two‐switch and the single‐switch flyback converters is given. The two‐switch flyback converter was bread‐boarded to validate the theoretical analysis. Experimental results from a 20‐V/30‐W, 100‐kHz laboratory prototype verified that the maximum switch voltage is limited to the DC input voltage. Copyright © 2010 John Wiley & Sons, Ltd.     

A half‐bridge resonant DC/DC converter with satisfactory soft‐switching characteristics

In this paper, a half‐bridge resonant DC/DC converter with constant output voltage is proposed, which possesses good soft‐switching characteristics. At rated operating point, the switches can operate almost without switching‐on and off losses. Further, at whole working range, both zero‐voltage‐switching mode of switches and zero‐current‐switching mode of diodes are maintained. Thus, the converter can achieve a high efficiency. Experimental results verify the low switching losses and high efficiency characteristics based on a 200 W prototype. System efficiency is as high as 96% and always above 90% when output power changes from 100% to 20%. Copyright © 2016 John Wiley & Sons, Ltd.     

A ZVS‐ZCS phase shift full bridge DC‐DC converter with secondary‐side control for battery charging applications

The output power requirement of battery charging circuits can vary in a wide range, hence making the use of conventional phase shift full bridge DC‐DC converters infeasible because of poor light load efficiency. In this paper, a new ZVS‐ZCS phase shift full bridge topology with secondary‐side active control has been presented for battery charging applications. The proposed circuit uses 2 extra switches in series with the secondary‐side rectifier diodes, operating with phase shift PWM. With the assistance of transformer's magnetizing inductance, the proposed converter maintains zero voltage switching (ZVS) of the primary‐side switches over the entire load range. The secondary‐side switches regulate the output voltage/current and perform zero current switching (ZCS) independent of the amount of load current. The proposed converter exhibits a significantly better light load efficiency as compared with the conventional phase shift full bridge DC‐DC converter. The performance of the proposed converter has been analyzed on a 1‐kW hardware prototype, and experimental results have been included.     

新型ZVZCT PWM直流变换器族的研究

提出了一种新型零电压零电流转换 (ZVZCT)软开关单元 ,并基于该开关单元 ,构造了BuckZVZCTPWM变换器和BoostZVZCTPWM变换器 ,形成新型ZVZCTPWM直流变换器族。详细分析了BuckZVZCTPWM变换器的工作原理 ,主开关管实现了零电压零电流开关 ,辅助开关管实现了零电流开通、零电压零电流关断 ,续流二极管实现了零电压零电流关断、零电压开通。该软开关单元不但适合于少子器件 ,而且适合于多子器件 ,同时保持PWM控制的特点。仿真分析和实验结果完全验证了理论分析的正确性     

A novel active auxiliary circuit for efficiency enhancement integrated with synchronous buck converter

In this paper, a novel auxiliary circuit is introduced for the synchronous buck converter. This auxiliary circuit provides zero‐current, zero‐voltage switching conditions for the main and synchronous switches while providing zero‐current condition for the auxiliary switch and diodes. The proposed active auxiliary circuit integrated with synchronous buck converter that emanates to zero‐voltage transition (ZVT)–zero‐current transition (ZCT) pulse width‐modulated (PWM) synchronous buck converter is analyzed, and its operating modes are presented. The additional voltage and current stresses on main, synchronous and auxiliary switches get decimated because of the resonance of the auxiliary circuit that acts for a small segment of time in the proposed converter. The important design feature of soft‐switching converters is the placement of resonant components that mollifies the switching and conduction losses. With the advent of ZVT–ZCT switching, there is an increase in the switching frequency that declines the resonant component values in the converters and also constricts the switching losses. The characteristics of the proposed converter are verified with the simulation in the Power Sim (PSIM) software co‐simulated with MATLAB/SIMULINK environment and implemented experimentally. Copyright © 2016 John Wiley & Sons, Ltd.     

A single‐stage LED streetlight driver with PFC and digital PWM dimming capability

This paper proposes a single‐stage light‐emitting diode (LED) driver that offers power‐factor correction and digital pulse–width modulation (PWM) dimming capability for streetlight applications. The presented LED streetlight driver integrates an alternating current–direct current (AC–DC) converter with coupled inductors and a half‐bridge‐type LLC DC–DC resonant converter into a single‐stage circuit topology. The sub‐circuit of the AC–DC converter with coupled inductors is designed to be operated in discontinuous‐conduction mode for achieving input‐current shaping. Zero‐voltage switching of two active power switches and zero‐current switching of two output‐rectifier diodes in the presented LED driver decrease the switching losses; thus, the circuit efficiency is increased. A prototype driver for powering a 144‐W‐rated LED streetlight module with input utility‐line voltages ranging from 100 to 120 V is implemented and tested. The proposed streetlight driver features cost‐effectiveness, high circuit efficiency, high power factor, low levels of input‐current harmonics, and a digital PWM dimming capability ranging from 20% to 100% output rated LED power, which is fulfilled by a micro‐controller. Satisfying experimental results, including dimming tests, verify the feasibility of the proposed LED streetlight driver. Copyright © 2016 John Wiley & Sons, Ltd.     

并联H桥DC/DC变换器软开关技术研究

与传统的Buck电路相比,基于H桥并联的DC/DC变换器可以实现电压的双极性输出和故障时的冗余控制,非常适合用于大功率电动机正反转控制的场合。分析了并联H桥型DC/DC变换器的结构组成和双脉宽调制(PWM)模式。为了降低双脉宽调制下H桥型DC/DC变换器的开通和关断损耗,对无源软开关技术进行了分析,重点探讨了RCD缓冲电路和最小应力缓冲电路之间的性能差异,指出最小应力软开关技术可以获得更好的软开关性能,并就将其用于双脉宽调制下的并联H桥DC/DC变换器进行了仿真研究。仿真结果表明:最小应力软开关技术用于双脉宽调制下并联H桥DC/DC变换器时,可以实现开关管的零电压开通和零电流关断。