EDM高程导线测量中的效率和精度问题探讨

随着全站仪测角测距精度的提高,在高程联测中,用EDM高程导线测量代替三四等水准测量,成为外业高程测量的重要方法之一。分析了影响EDM高程导线测量精度的因素,讨论了提高EDM高程导线测量精度的办法,提出了效率函数的概念,并以某测区三级GPS大地控制网高程联测数据为例,从精度和效率方面进行了计算对比分析。     

测距高程导线数据处理软件设计与实现

针对目前测距高程导线计算表格多、数据繁杂、处理起来容易出错,且效率低的现状,在研究分析了测距高程导线基本原理以及上交资料数据格式后,使用C#语言在Visual Studio2005.NET平台上,设计并实现了测距高程导线数据处理软件,该软件为内业资料处理节省大量时间的同时,对外业测量结果也可进行实时计算,提高了工作效率。     

城市与工程测量EDM导线技术标准的分析

基于导线测量误差理论与电磁测距(EDM)导线的特性,分析讨论了城市与工程测量EDM导线的各项技术参数,提出了各级EDM导线技术标准的建议,通过计算验证所给出的这些技术指标是合理可靠的。     

基于声学宽带扩频信号的抗多径测距技术研究

为研究宽带扩频信号在复杂水声信道下的测距精度,提高水声定位系统的抗多径性能,以BELLHOP模型的多径干扰冲激响应作为水声信道环境基础,通过构造不同传播距离、海洋环境特征的多径水声信道,对宽带扩频编码进行同步相关测距仿真;提出一种基于宽带扩频信号载波域同步的抗多径测距方法,利用载波携带的宽带特征信息进行相关同步以提高理论测距精度。实验结果表明：在有直达声且不考虑声线弯曲条件下,浅海多径信道条件测距精度可达厘米级,中深水信道维持分米级测距精度,较基带同步方法的抗干扰性能有所提升,基于宽带扩频信号载波域同步的抗多径测距方法,能够为声学定位系统的高性能测距技术提供理论依据。     

基于单水声信标距离量测的匹配定位方法

水声通信和测距能力是实现水下航行器准确定位的重要技术手段。当前基于水声定位的方法主要有利用测距和测向功能的水声定位技术以及水声测距辅助导航技术，二者的系统物理复杂度都比较高。本文提出了一种基于单水声信标距离量测的匹配定位方法，航行器在水声信标测距覆盖范围内，利用航行过程中多次测距信息构建测距圆序列形成位置约束，基于航位推算导航信息，将航行器在连续测距时间段内的相对航迹在圆序列上进行最优匹配，从而获得位置估计，通过对测距误差进行补偿可进一步提升定位精度。本方法所需物理系统结构复杂度低、可操作性强，仿真实验表明，该方法可以独立实现较高精度的定位。     

海洋测高卫星三频体制设计及电离层误差分析

针对海洋测高卫星未来发展趋势,提出了Ku/Ka/C三频高度计进行组合测距的设想。给出了高度计相位中心至海面距离的随机误差模型,分析表明电离层延迟改正是影响海面高测量分辨率和精度的重要因素。其次利用典型电离层参数计算表明电离层2阶以上项对高度计测距的影响在毫米级以下,可忽略其影响。通过计算分析,在1Hz采样且不滤波条件下,Ka/C组合改正电离层1阶项精度可优于3mm,基本消除电离层的影响,测距总精度达到3.5cm。通过Ku/C/Ka三频组合测距误差分析,三频电离层改正残余误差比双频改正更大,因此如果采用三频组合测距体制,则建议在数据处理中采取Ku/C、Ka/C组合形式改正电离层,这种体制可充分利用各频段特点,进一步提高宽阔海域、冰区、近海区域的海面测量精度和有效数据比例。     

测距仪倾斜引起的误差分析与改正

重点研究积木式全站仪在大垂直角测距中由于测距仪中心与经纬仪中心不一致而引起的测距误差,针对这些误差的来源及特征,制定出相应的修正措施,从而达到提高测距精度的目的。     

导线测量中全站仪棱镜常数的影响

针对导线测量中棱镜常数设置错误的情况,分析了导线验算无法检核棱镜常数使用错误的原因,研究了棱镜常数使用错误对平差结果的影响,提出了导线测量中棱镜常数使用是否正确的检测方法,通过使用该方法可以避免距离测量的粗差,从而保证导线测量的精度。     

闭合导线测量中边长系统误差分析

在闭合导线测量中,导线边如果存在系统误差,其解算结果仍可能满足现行规范中的各项精度指标。通过一项边长接近的闭合导线测量实例,分析了产生误差的原因与对策,解算出符合要求的测量成果。     

闭合导线边长系统误差的影响

结合实例分析了闭合导线测量中边长加常数粗差对导线闭合差的影响规律，从理论上证明了边长的比例误差不影响闭合导线的闭合差，并说明了导线的方位角闭合差和相对闭合差作为限差的不可靠性，指出了闭合导线测量中应当注意的若干问题。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~