Indoor and outdoor concentrations of PM2.5 trace elements at homes, preschools and schools in Stockholm, Sweden

Fine particles (PM2.5) were sampled indoors and outdoors at 40 sampling sites; in ten classrooms in five schools, at ten preschools and 20 non-smoking homes, in three communities in Stockholm, Sweden, during nine 2-week periods. Each sampling site was sampled twice, once during winter and once during spring. The samples were analysed for elemental concentrations using X-ray fluorescence (XRF) spectroscopy. In all locations significantly higher outdoor concentrations were found for elements that are related to long-range transported air masses (S, Ni, Br and Pb), while only Ti was higher indoors in all locations. Similar differences for S, Br and Pb were found in both seasons for homes and schools. In preschools different seasonal patterns were seen for the long-range transported elements S, Br and Pb and the crustal elements Ti, Mn and Fe. The indoor/outdoor ratios for S and Pb suggest an outdoor PM2.5 particle net infiltration of about 0.6 in these buildings. The community located 25 km from the city centre had significantly lower outdoor concentrations of elements of crustal or traffic origin compared with the two central communities, but had similar levels of long-range transported elements. Significant correlations were found between PM2.5 and most elements outdoors (rs = 0.45-0.90). Copper levels were found to correlate well (rs = 0.64-0.91) to the traffic marker NO2 during both winter and spring in all locations. Copper may be a suitable elemental marker for traffic-related aerosols in health studies in areas without other significant outdoor Cu sources.     

Chemical Composition and Sources of PM10 and PM2.5 Aerosols in Guangzhou, China

Aerosol samples of PM10 and PM2.5 are collected in summertime at four monitoring sites in Guangzhou, China. The concentrations of organic and elemental carbons (OC/EC), inorganic ions, and elements in PM10 and PM2.5 are also quantified. Our study aims to: (1) characterize the particulate concentrations and associated chemical species in urban atmosphere (2) identify the potential sources and estimate their apportionment. The results show that average concentration of PM2.5 (97.54 μg m⁻³) in Guangzhou significantly exceeds the National Ambient Air Quality Standard (NAAQS) 24-h average of 65 μg m⁻³. OC, EC, Sulfate, ammonium, K, V, Ni, Cu, Zn, Pb, As, Cd and Se are mainly in PM2.5 fraction of particles, while chloride, nitrate, Na, Mg, Al, Fe, Ca, Ti and Mn are mainly in PM2.5-10 fraction. The major components such as sulfate, OC and EC account for about 70–90% of the particulate mass. Enrichment factors (EF) for elements are calculated to indicate that elements of anthropogenic origins (Zn, Pb, As, Se, V, Ni, Cu and Cd) are highly enriched with respect to crustal composition (Al, Fe, Ca, Ti and Mn). Ambient and source data are used in the multi-variable linearly regression analysis for source identification and apportionment, indicating that major sources and their apportionments of ambient particulate aerosols in Guangzhou are vehicle exhaust by 38.4% and coal combustion by 26.0%, respetively.     

Composition, seasonal variation, and sources of PM10 from world heritage site Taj Mahal, Agra

Air samples for PM(10) (dp?相似文献   

Airborne particulate matter and BTEX in office environments

Total suspended particulate (TSP), PM(2.5) and BTEX were collected in nine offices in the province of Antwerp, Belgium. Both indoor and outdoor aerosol samples were analysed for their weight, elemental composition, and water-soluble fraction. Indoor TSP and PM(2.5) concentrations ranged from 7-31 microg m(-3) and 5-28 microg m(-3), with an average of 18 and 11 microg m(-3), respectively. Of all the elements analysed in indoor TSP, more than 95% was represented by Al, Si, K, Ca, Fe, Cl and S, accounting for 12% of the TSP by mass. The other elements showed significant enrichment relative to the earth's crust. The water-soluble ionic fraction accounted for almost 30% of the sampled indoor TSP by weight, and was enriched by anthropogenic activities. It was shown that the indoor PM levels varied among the offices, depending on the ventilation pattern, location, and occupation density of the office. Indoor BTEX levels ranged together from 5-47 microg m(-3) and were considerably higher than the corresponding outdoor levels. It was observed that some recently constructed and renovated buildings were clearly burdened with elevated levels for toluene, ethyl benzene, and xylenes, while outdoor air was found to be the main source for BTEX levels at the 'older' offices.     

Characterization of PM10 and PM2.5 and associated heavy metals at the crossroads and urban background site in Zabrze, Upper Silesia, Poland, during the smog episodes

The concentrations of seven heavy metals (Cd, Cr, Cu, Fe, Mn, Ni, and Pb) associated with PM10 and PM2.5 at the crossroads and the background sites have been studied in Zabrze, Poland, during smog episodes. Although the background level was unusually elevated due to both high particulate emission from the industrial and municipal sources and smog favorable meteorological conditions, significant increase of the concentration of PM2.5 and PM10 as well as associated heavy metals in the roadside air compared to the urban background has been documented. The average daily difference between the roadside and corresponding urban background aerosol concentration was equal to 39.5 μg m^???3 for PM10 and 41.2 μg m^???3 for PM2.5. The highest levels of the studied metals in Zabrze appeared for iron carried by PM10 particles: 1,706 (background) and 28,557 ng m^???3 (crossroads). The lowest concentration level (in PM10) has been found for cadmium: 7 and 77 ng m^???3 in the background and crossroads site, respectively. Also the concentrations of heavy metals carried by the fine particles (PM2.5) were very high in Zabrze during the smog episodes. Concentrations of all studied metals associated with PM10 increased at the roadside compared to the background about ten times (one order) while metals contained in PM2.5 showed two to three times elevated concentrations (except Fe—five times and Cr—no increase).     

Major and trace elements’ concentrations in hard and soft tissues of kutum, <Emphasis Type="Italic">Rutilus kutum</Emphasis>, from the Caspian Sea and their potential use as biomonitoring tools

The potential use of different hard and soft parts (otolith, scale, eye lens, dorsal spine, vertebral bone, muscle, and liver) of Rutilus kutum for biomonitoring of 13 major and trace elements (Br, Ca, Cl, Cu, Fe, K, Mg, Mn, Na, P, S, Sr, and Zn) was evaluated, for the first time. The specimens were sampled from three sampling sites in the Southern Caspian Sea in May 2016. Twenty specimens were collected from each site. The elements’ concentrations in the samples were measured by proton-induced X-ray emission (PIXE). In all the hard tissues, except for eye lens, Ca was the most abundant element, whereas Fe was among the least abundant elements. The orders of element occurrence in the two soft tissues were largely similar. Ca, Fe, S, Cl, and K could be detected in all the selected tissues, while Br was detectable only in otolith. Minor similarities among the tissues were identified in the case of eye lens (concerning P, S, and Zn) and liver (in terms of Cl, Fe, and K), whereas, in the case of Sr and Ca, otolith shows the maximum distance. In general, it can be concluded that all the studied hard parts, except for eye lens, may offer alternatives for biomonitoring of Ca, Cl, Fe, K, and S in the southern Caspian Sea. The scales and spines represent a potential non-lethal alternative to the other hard parts.     

Particulate matter characterization at a coastal site in south-eastern Italy

Several samples of airborne particulate matter (PM), collected from 6th November to 6th December 2003 at a coastal site in the south-east of Italy, have been analyzed by different techniques to characterize elemental composition and morphological properties of the inorganic PM fraction and obtain preliminary results on anthropogenic contributions. Al, Cr, Cu, Fe, Mn, V, Pb, Ti, Ca and Zn mass concentrations, evaluated by an inductively coupled plasma atomic emission spectrometer, account for up to l% of the bulk PM mass in the investigated samples. According to geochemical calculations, Ca, Al, Fe and Mn are predominantly of crustal origin, while Cr, Cu, Pb, V, Ti and Zn heavy metals are of anthropogenic origin. Ion chromatography analyses have identified sulfate (SO(4)(2-)) nitrate (NO(3)(-)), sodium (Na(+)), and ammonium (NH(4)(+)) as the main ionic components accounting for up to 38% of the total PM mass and up to 90% of the total ionic mass. Besides ion chromatography, X-ray energy dispersive (EDX) microanalyses have revealed the high variability of Cl: its weight concentration varies from about 24% to below the detection limit (>or=0.5%) in the investigated samples. The marked anti-correlation between the excess of S and the Cl/Na ratio has allowed inferring that reactions between sea salt particles and acidic sulfates, which liberate HCl gas to the atmosphere leaving particles enriched in non-sea-salt sulfates, have significantly contributed to chloride depletion. Morphological analyses by scanning electron microscopy have shown that about 90% of the total sampled particles have a diameter 相似文献   

PM2.5 in the central part of Upper Silesia, Poland: concentrations, elemental composition, and mobility of components

The paper discusses ambient concentrations of PM_2.5 (ambient fine particles) and of 29 PM_2.5-related elements in Zabrze and Katowice, Poland, in 2007. The elemental composition of PM_2.5 was determined using energy dispersive X-ray fluorescence (EDXRF). The mobility (cumulative percentage of the water-soluble and exchangeable fractions of an element in its total concentration) of 18 PM_2.5-related elements in Zabrze and Katowice was computed by using sequential extraction and EDXRF combined into a simple method. The samples were extracted twice: in deionized water and in ammonium acetate. In general, the mobility and the concentrations of the majority of the elements were the same in both cities. S, Cl, K, Ca, Zn, Br, Ba, and Pb in both cities, Ti and Se in Katowice, and Sr in Zabrze had the mobility greater than 70%. Mobility of typical crustal elements, Al, Si, and Ti, because of high proportion of their exchangeable fractions in PM, was from 40 to 66%. Mobility of Fe and Cu was lower than 30%. Probable sources of PM_2.5 were determined by applying principal component analysis and multiple regression analysis and computing enrichment factors. Great part of PM_2.5 (78% in Katowice and 36% in Zabrze) originated from combustion of fuels in domestic furnaces (fossil fuels, biomass and wastes, etc.) and liquid fuels in car engines. Other identified sources were: power plants, soil, and roads in Zabrze and in Katowice an industrial source, probably a non-ferrous smelter or/and a steelwork, and power plants.     

Ambient site, home outdoor and home indoor particulate concentrations as proxies of personal exposures

Despite strong longitudinal associations between particle personal exposures and ambient concentrations, previous studies have found considerable inter-personal variability in these associations. Factors contributing to this inter-personal variability are important to identify in order to improve our ability to assess particulate exposures for individuals. This paper examines whether ambient, home outdoor and home indoor particle concentrations can be used as proxies of corresponding personal exposures. We explore the strength of the associations between personal, home indoor, home outdoor and central outdoor monitoring site ("ambient site") concentrations of sulfate, fine particle mass (PM(2.5)) and elemental carbon (EC) by season and subject for 25 individuals living in the Boston, MA, USA area. Ambient sulfate concentrations accounted for approximately 70 to 80% of the variability in personal and indoor sulfate levels. Correlations between ambient and personal sulfate, however, varied by subject (0.1-1.0), with associations between personal and outdoor sulfate concentrations generally mirroring personal-ambient associations (median subject-specific correlations of 0.8 to 0.9). Ambient sulfate concentrations are good indicators of personal exposures for individuals living in the Boston area, even though their levels may differ from actual personal exposures. The strong associations for sulfate indicate that ambient concentrations and housing characteristics are the driving factors determining personal sulfate exposures. Ambient PM(2.5) and EC concentrations were more weakly associated with corresponding personal and indoor levels, as compared to sulfate. For EC and PM(2.5), local traffic, indoor sources and/or personal activities can significantly weaken associations with ambient concentrations. Infiltration was shown to impact the ability of ambient concentrations to reflect exposures with higher exposures to particles from ambient sources during summer. In contrast in the winter, lower infiltration can result in a greater contribution of indoor sources to PM(2.5) and EC exposures. Placing EC monitors closer to participants' homes may reduce exposure error in epidemiological studies of traffic-related particles, but this reduction in exposure error may be greater in winter than summer. It should be noted that approximately 20% of the EC data were below the field limit of detection, making it difficult to determine if the weaker associations with the central site for EC were merely a result of methodological limitations.     

TSP, PM depositions, and trace elements in the vicinity of a cement plant and their source apportionments using chemical mass balance model in Izmir, Turkey

Total suspended particles mass concentrations (TSP) and bulk depositions of particulate matter (PM depositions) were measured around a cement plant located in the multi-impacted area to assess the affect of the plant on the ambient air in the vicinity in Izmir, Turkey. TSP samples were collected five times a month whereas PM depositions were sampled monthly at four sites between August 2003 and January 2004. The concentrations of Al, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, V, and Zn in TSP and PM depositions (except Cu) were reported. Chemical mass balance (CMB) receptor model with local source profiles was run in order to calculate the source contributions of the PM sources to the concentrations of TSP, PM depositions, and trace elements. Traffic was found to be the major contributor to TSP whereas PM depositions dominantly result from area sources including several stone quarries, concrete plants, lime kilns, and asphalt plants in the region. CMB model results indicate that the cement plant is a significant contributor to TSP, PM depositions, and trace elements, particularly Cd.     

Characterization of metal aerosols in PM10 from urban, industrial, and Asian Dust sources

Metallic elements (As, Be, Ca, Cd, Co, Cr, Fe, K, Mn, Ni, Pb, Sb, Se, and Zn) in PM10 aerosols were determined at urban and industrial sites, which are affected by traffic and residential sources, metallurgical activity, and petrochemical and steel works. The effect of the long-range transported Asian Dust on the metal content of aerosols was also examined. At the urban sampling site, concentrations of As, Cd, Pb, Se, and Zn were assigned to road traffic and combustion sources, Ca and Fe to soil dust sources from long-range transported Asian Dusts, and Cr and Ni to metallurgical sources transported from the nearby industrial complex, based on Principal Component Analysis (PCA). Enhanced Cr and Ni concentrations at the metallurgical industrial site suggest that local emissions from metal-assembly facilities and manufacture of alloys contributed to elevated levels of those metals. We also observed that petrochemical activities contributed to increased levels of Sb and Zn. When Asian Dust events occurred, Ca, Fe, K, and Zn concentrations dramatically increased compared to values without the Asian Dust. Two different types of Asian Dust events were observed. For the Asian Dust event 1 (4/1/2007), the Fe and K concentrations were much higher by a factor of 2–3 than those for the Asian Dust event 2 (3/2/2008), while As, Mn, and Zn concentrations were significantly higher on the Asian Dust event 2. Backward trajectory analysis showed that for the Asian Dust event 2, the air mass had passed over the heavily industrialized zones in China during long-range transport to the current sampling site, suggesting that the As, Mn, and Zn may have originated from industrial sources.     

天津市颗粒物中元素化学特征及来源

2006年的8月—12月采集天津市PM2.5和PM10样品,分析了Na、Al等17种元素质量浓度及月变化特征,PM2.5中元素平均质量浓度为17.2μg/m3,占PM2.5的10.3%。微量元素Zn、Pb在PM10和PM2.5中含量较高,Cr、V、Ni、As等则在细粒子中有明显分布。用富集因子法分析发现,PM2.5中元素富集程度高于PM10。地壳元素除Ca外,均无明显富集,微量元素则呈现不同程度的富集,以Cd富集最为明显。颗粒物分析表明,土壤尘、燃煤、机动车尾气及化工行业是PM2.5中无机元素的主要来源。     

Characterization of atmospheric aerosols in the city of S?o Paulo, Brazil: comparisons between polluted and unpolluted periods

The objective of this study was to determine the size and composition of atmospheric aerosols in the downtown area of the city of S?o Paulo, Brazil, for a polluted and an unpolluted period. Aerosols were sampled with a portable air sampler (PAS), Micro-Orifice Uniform Deposit Impactor (MOUDI), and Scanning Mobility Particle Sizer. At the study site, air quality is poor, especially during the winter, high concentrations of pollutants being emitted primarily by the light- and heavy-duty vehicle fleet. We analyzed mass, black carbon (BC), Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sn, Zr, and Pb. During the polluted period, diurnal PM₁₀ was higher than nocturnal PM₁₀, whereas the inverse was true during the unpolluted period. The FPM was rich in BC, S, and Pb, whereas CPM was rich in Al, Si, Ca, Ti, and Fe. Mass balance was performed by category: ammonium sulfate, sodium chloride, crustal material, BC, and other. The PAS-determined FPM was mainly BC. The MOUDI-determined FPM crustal material explained more mass than did ammonium sulfate and BC during the polluted period, whereas ammonium sulfate had the largest mass during the unpolluted period. Crustal material was the major CPM component, followed by ammonium sulfate and BC. During the unpolluted period, FPM concentrations were lower, whereas those of ammonium sulfate were relatively higher, especially at night, and particle number was inversely proportional to particle size. Aerosol growth was more intense during the polluted period.     

Personal exposure measurement of students to various microenvironments inside and outside the college campus

This study characterizes the exposure of a typical Indian Institute of Technology Kanpur student to particulate matter and gaseous co-pollutants like carbon monoxide, volatile organic compounds, and nitrogen dioxide in various microenvironments, within and outside the college campus. Chemical analysis of filter, used for the particulate matter measurement, was also carried out to determine the concentration of various elements such as Ca, Cd, Cr, Cu, Fe, Mg, Pb, Zn, and anions like F^?, Cl^?, NO₃ ^?, and SO₄ ^2?. Furthermore, time activity diary along with temperature data was maintained for the precise evaluation and analysis of results for various microenvironments. The results showed PM₁₀ and PM_2.5 concentrations to be higher at some outdoor microenvironments, particularly near the Ganga riverbank. From the chemical analysis, concentrations of chloride and fluoride were found higher in indoor microenvironments as compared to outdoors. Also, nitrate concentrations were quite higher within the laboratory premises. Concentrations of Ca, Fe, and Mg were significant outdoors, whereas Na, Ca, Fe, and K were prominent indoors. The study highlights the real-time personal exposure of a student cohort to various toxic pollutants typically found within their breathing levels and their potential sources both indoors and outdoors.     

平顶山市大气PM10、PM2.5 污染调查

于2003年12月-2004年11月对平顶山市城区大气PM10、PM2.5污染进行了调查.结果表明,2004年大气PM10、PM2.5质量浓度分别为0.031 mg/m3～0.862 mg/m3、0.019 mg/m3～0.438 mg/m3;年均值分别为0.174 mg/m3、0.114 mg/m3,超标0.74倍、6.60倍.PM10、PM2.5污染的季节变化趋势是以冬季、春季高,秋季次之,夏季最低,细颗粒(PM2.5)约占PM10 65%;As、Pb、Cd、S、Zn、Cu、Mn、Ca等元素是颗粒物中主要污染元素,易在PM2.5中富集.平顶山市大气颗粒物污染的主要来源有煤炭燃烧、汽车尾气、城市基础建设和有色金属冶炼行业.     

桂林市细颗粒物部分典型排放源的粒径谱及成分分析

采用在线单颗粒气溶胶质谱技术源解析方法,对桂林市PM2.5典型排放源的粒径和化学成分进行质谱分析,采集燃煤/燃气源、工业工艺源、扬尘源、油烟源4类共计7个典型排放源。结果表明,桂林市4类排放源细颗粒物的粒径分布为0.25~1.25μm,80%以上的细颗粒分布在0.2~1.0μm的小粒径范围,峰值约0.68μm。细颗粒物离子成分含有Na~+、Mg~+、K~+、NH~+4、Fe~+、Pb~+、Cd~+、V~+、Mn~+、Li~+、Al~+、Ca~+、Cu~+、Zn~+、Cr~+、CN~-、PO_3~-、NO_2~-、NO_3~-、Cl~-、SO_4~(2-)、SiO_3~-等成分,桂林市细颗粒物为元素碳、有机碳元素碳、有机碳、富锰颗粒、富铁颗粒、富钾颗粒、矿物质、左旋葡聚糖以及其他金属等9类。     

遵义市PM10中元素污染特征、来源与生态风险评价

采集2012年3月-2013年2月遵义市丁字口（市区点）、凤凰山（背景点）监测点的 PM10样品，并对 PM10中元素污染特征、来源和生态风险进行分析与评价。结果表明，遵义市 PM10质量浓度季节变化为：冬季＞春季＞秋季＞夏季，且市区点高于背景点，冬季超标率均为100％。PM10中 As、Pb、Hg、Mn质量浓度市区点高于背景点，且均为冬季最高。富集因子分析表明，Pb、As、Cd、Hg、Mn、Cu、Zn来自人为污染，生态危害顺序为：Cd＞Pb ＞As＞Cu ＞Zn ＞Ni ＞Cr，其中 Cd 的潜在生态危害为极强。     

河南省典型城市PM2.5无机元素污染特征及来源分析

分析2012年采暖季和非采暖季郑州市、洛阳市和平顶山市大气细颗粒物(PM_(2.5))样品中22种无机元素含量和污染特征,采用富集因子法、因子分析法研究当地PM_(2.5)中无机元素来源。结果表明:3个城市PM_(2.5)中无机元素总量在采暖季均高于非采暖季,不同季节占PM_(2.5)质量浓度的比例为1.7%~3.6%。Al、Na、Ca等地壳元素在PM_(2.5)中占比与PM_(2.5)浓度呈负相关关系,而Zn、Pb、Cu等人为源元素的占比随PM_(2.5)浓度增加无明显下降趋势。3个城市PM_(2.5)中Se、Cd、Br的富集因子高于1 000,Pb、Zn、Cu的富集因子为100~1 000,Co、Sc、Cr、Ni、As、Mn、Ba的富集因子为10~100,说明这些元素主要来源于人为源。13种人为源元素质量浓度在22种元素中占比为18.9%~26.3%,K、Fe、Ca、Al等4种元素占比为67.9%~76.1%。因子分析结果表明:3个城市无机元素来源组成有很大相似性,主要来源于燃煤、机动车、扬尘和建筑尘等,但Ni、Co、Sr、Ba还有来自其他排放源的贡献。     

Evaluation of a portable nephelometer against the Tapered Element Oscillating Microbalance method for monitoring PM(2.5)

Monitoring personal exposure to particle matter (PM(2.5)) in ambient air requires performing measurements using portable monitors. In this work, the portable nephelometer SidePak? AM510 Personal Aerosol Monitor manufactured by TSI Inc. was evaluated against a Tapered Element Oscillating Microbalance (TEOM) equipped with a Filter Dynamics Measurements System (FDMS). Conventionally, the SidePak is calibrated with respect to the Arizona Road Test Dust and then multiplied by an environmental calibration factor to yield mass concentration. To adapt this calibration to specific field conditions, we present an implementation of this calibration by introducing a growing factor correction which takes into account relative humidity and the dry and wet portions of the refractive index estimated from TEOM-FDMS measurements. PM(2.5) sampling with several SidePaks AM510 was carried out in background and rural sites in the Po Valley (Italy). Modeled SidePak data were plotted vs. reference TEOM-FDMS data which show a good agreement.     

Air Pollution in Singapore: Its Multielemental Aspect as Measured by Nuclear Analytical Techniques

Aerosol samples were collected in 1994 in Singapore on two occasions: once in June during the normal meteorological conditions and later in October during a long haze period caused by the heavy forest fire in Indonesia. Filtration and impaction collection methods were used simultaneously so that detailed elemental analysis of bulk as well as of different size fractions could be performed. Accelerator based nuclear analytical techniques such as Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and Nuclear Microscopy (NM) were used for analysis. These techniques are fast, truly multielemental and perfectly suited for routine analysis of a large number of aerosol samples. Typically all samples were analysed for the following 24 elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Mn, Cr, Fe, Co, Ni, Cu, Zn, Ga, As, Br, Rb, Sr and Pb. Detection limits for bulk analysis were generally below ng/m3 and for single particle analysis absolute detectable mass was approximately 10-17 g. Additionally, trace elements such as Cd, Sn, Sb and Ba whose characteristic X-ray lines were normally "obscured" by the lines of other more abundant elements, were detected when analysing by nuclear microscope in single particle mode.Judging by the average concentrations of lead and sulphur which are good indicators of industrial component of air pollution the situation in Singapore is satisfactory. Pb was typically found in concentrations of 5 to 50 ng/m3 and sulphur in concentrations of 1 to 2 µg/m3. These concentrations are well below limits set by the World Health Organisation (1500 ng/m3 and 40 µg/m3, respectively). On the other hand during the haze period the average concentrations of elements like S, K, Ti, V, Mn, Ni, As and Pb were found to be 3 to 6 times higher than usual. Results are presented and discussed.