亲水-疏水PVP-semi-IPN-PCL水凝胶的制备与溶胀性能

N-乙烯基吡咯烷酮（NVP）在聚己内酯（PCL）的乙酸乙酯溶液中进行自由基聚合，制备了亲水-疏水性聚乙烯吡咯烷酮（PVP）/聚己内酯（PCL）半互穿网络水凝胶（PVP-semi-IPN-PCL）。凝胶中PCL的熔融温度T_m无明显变化，而T_m吸热峰形状随PVP含量变化。凝胶平衡溶胀率（ESR）随PVP含量的升高而增大，结合水量的增大尤其显著。由于“笼蔽效应”，低浓度引发剂时，偶氮二异丁睛（AIBN）引发制备的凝胶ESR低于过氧化苯甲酰（BPO）引发剂。交联剂浓度较低时，以戊二醛交联形成凝胶的ESR较N，N-亚甲基双丙烯酰胺（NMBA）交联形成的凝胶大。浓度较高时，戊二醛交联凝胶ESR较NMBA低。PVP含量（质量）分别为20%、40%、60%、80%时，凝胶溶胀动力学Fick模型中的n值分别为0.854、0.471、0.466、0.253，说明在合适的PVP含量时，凝胶的溶胀动力学符合Fick模型。     

NVP接枝壳聚糖水凝胶的合成与溶胀性能

合成了N-乙烯基吡咯烷酮（NVP）接枝壳聚糖（CHI）水凝胶,讨论了NVP/CHI、引发剂、交联剂、聚合温度、乙酸浓度等因素对接枝率及凝胶溶胀性能的影响,NVP∶CHI为6时,接枝率达到300%以上. 溶胀温度、pH值、盐浓度等对凝胶溶胀性能的影响实验表明,凝胶表现出温度敏感性,在40 ℃出现最大平衡溶胀率,并观察到一级相转变;在中性或弱酸性介质中溶胀性能较好;与PVP凝胶相比,NVP接枝CHI凝胶表现出反聚电解质效应. 溶胀动力学研究表明,在溶胀前期,CHI含量较高时,凝胶趋向于非Fick溶胀,说明除了溶剂扩散外,凝胶网络链段弛豫、水分子与凝胶网络间及凝胶高分子链段间相互作用对凝胶溶胀性能的影响至关重要;CHI含量较高时则趋向于Fick溶胀.     

Water sorption behavior of CMC/PAM hydrogels prepared by γ-irradiation and release of potassium nitrate as agrochemical

Novel types of highly swelling CMC/PAM hydrogels have been prepared by grafting cross-linked polyacrylamide (PAM) chains onto carboxymethylcellulose (CMC) via a free radical polymerization method using γ-irradiation. The prepared CMC/PAM hydrogels were characterized by FT-IR spectral analysis. The AM content and irradiation dose had a direct effect on gel content of CMC/PAM hydrogels and inverse effect on their swelling ratio. The hydrogels showed enormous swelling in aqueous medium and displayed swelling characteristics which were highly dependent on the chemical composition of the hydrogel, pH and ionic strength of the medium in which the hydrogel was immersed. The results were supported by morphological properties of CMC/PAM hydrogels by using SEM. The kinetics of water uptake and the water transport mechanism were studied as a function of the CMC/AM ratio into the prepared hydrogel. The release rate of potassium nitrate entrapped within the CMC/PAM matrix increased by enhancing its loading %, and decreased with lowering AM content and irradiation dose.     

The effect of PEG(400)DA crosslinking agent on swelling behaviour of acrylamide-maleic acid hydrogels

Summary Acrylamide (AAm)-maleic acid (MA) hydrogels with different monomer ratios were prepared in an aqueous solution by radical polymerization using a new crosslinking agent, polyethyleneglycol (400) diacrylate (PEG (400) DA) and also using N, N’-methylenebisacrylamide (NMBA) for comparison purpose. The hydrogels were characterized by acid group content and FTIR spectroscopy. Their swelling and deswelling behavior were studied as a function of maleic acid content, pH and crosslinking agent. Incorporation of MA in hydrogels significantly increased their swelling ability and their equilibrium degree of swelling (EDS) values changed between 100–269 g water/g polymer in water while AAm polymers swollen less (22–23 g water/g polymer). The AAm hydrogels showed Fickian type diffusion but the all AAm-MA hydrogels showed non-Fickian type behavior. Their swelling degree increased with the increase of pH of the external medium and an instantaneous increase was observed near a pH value of 7.0. The use of PEG (400) DA instead of NMBA as a crosslinking agent also increased the swelling rate and capacity of the gel. The swelling constant (K) and the diffusion coefficient (D) of hydrogels were also increased. The swelling-deswelling cycles in acidic-basic solutions showed that they could be used as pH responsive gels without any decrease in swelling capacity.     

Preparation of biodegradable crosslinking agents and application in PVP hydrogel

Firstly, biodegradable crosslinking agents (BCA) were synthesized by ring‐opening polymerization reaction of lactide, four kinds of which with different molecular weights were got by means of changing the ratio of DL ‐lactide(LA) and glycerol(GL). Then a series of poly(N‐vinyl pyrrolidone) (PVP) hydrogels were prepared successfully by radical polymerization of BCA and N‐vinyl pyrrolidone(NVP). Both the ratio of NVP/BCA and the molecular weight of BCA were used to control the performance of PVP hydrogels, which were measured in terms of the ratio of swelling, contact angle, mechanical properties, and biodegradability in vitro. This study showed that increasing both the ratio of NVP/BCA and the molecular weight of BCA resulted in a low crosslinking density of the hydrogels. The crosslinking density played an important role in determining the properties of biodegradable PVP hydrogels. Both the ratio of NVP/BCA and the molecular weight of BCA contributed to high ratio of swelling. A smaller amount of crosslinking agent caused a lower contact angle, while the molecular weight of BCA had little effect on it. In terms of mechanics of hydrogels on both dry and wet conditions, tensile modulus decreased along with decreasing BCA, while the extension at break increased at the beginning and decreased at the end. In the end, measured by mass loss, biodegradability in vitro of hydrogels had two stages: an initial stage with approximately constant loss of mass (stage 1) followed by a stage with rapid mass loss (stage 2). Both increased content and molecular weight of BCA improved the degradation rate of the hydrogels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1515–1521, 2006     

Investigation of mechanical and thermodynamic properties of pH‐sensitive poly(N,N‐dimethylaminoethyl methacrylate) hydrogels prepared with different crosslinking agents

pH‐sensitive poly(N,N‐dimethylaminoethyl methacrylate) hydrogels were synthesized by free‐radical crosslinking polymerization using two different crosslinking agents; tetraethylene glycol dimethacrylate (TEGMA) and N,N′‐methylenebis(acrylamide) (BAAm). The influence of the polymerization factors such as the type of the crosslinking agent and the gel preparation concentration on the swelling behavior, the gel strength, the effective crosslinking density and the average chain length between the crosslink points for the resulting hydrogels was investigated. The results of the equilibrium swelling measurements in water showed that the linear swelling ratio of the resulting hydrogels increases with increasing gel preparation concentration. The swelling ratio of PDMAEMA hydrogels crosslinked with BAAm is larger than those for hydrogels crosslinked with TEGMA over the entire range of the polymer network concentration. The hydrogels exhibit very sharp pH‐sensitive phase transition in a very narrow range of pH between 7.7 and 8.0. From the mechanical measurements, it was also found that the linear swelling ratio of resulting hydrogels depends on the crosslinking density and also the type of the crosslinker used in the preparation. The resulting hydrogels are thought to be good candidates for pH‐sensitive drug delivery systems. POLYM. ENG. SCI. 2013. © 2012 Society of Plastics Engineers     

通过RAFT聚合方法合成具有高强度和高溶胀率的纳米水凝胶

为了得到具有高强度和高溶胀率的纳米水凝胶(NCgels),N-异丙基丙烯酰胺通过可逆加成断裂链转移(RAFT)聚合的方法,插层在含有质量分数为0.25%～15%的可扩展的有机化的蒙脱土(Clay-S)层间并交联。结果表明,与传统水凝胶相比,该水凝胶的强度和溶胀性能得到了很大提高,并且对温度的变化具有较快的响应速率。以质量分数为5%的蒙脱土,链转移剂的质量分数为0.5%制备的纳米水凝胶为例,该水凝胶在20℃的溶胀率为450,而传统水凝胶在相同温度时的溶胀率仅为20;该水凝胶在1min内失去75%的水,在4min内失去约90%的水,而传统水凝胶在15min内仅失去66%左右的水。     

Partially hydrolyzed kappa carrageenan—polyacrylonitrile as a novel biopolymer‐based superabsorbent hydrogel: Synthesis,characterization, and swelling behaviors

In this paper, synthesis and swelling behavior of a novel superabsorbent hydrogel based on kappa carrageenan (κC) and polyacrylonitrile (PAN) was investigated. To achieve partially hydrolyzed κC‐PAN hydrogel, physical mixture of κC and PAN was hydrolyzed by NaOH solution. During alkaline hydrolysis, the nitrile groups of PAN are converted to a mixture of hydrophilic carboxamide and carboxylate groups follow by in situ crosslinking of the grafted PAN chains. The reaction variables affecting on the swelling capacity of the hydrogel were systematically optimized to achieve a hydrogel with swelling capacity as high as possible. Under the optimized conditions concluded, super swelling hydrogel with the ability of water absorption up to 3260 g/g (water/dry hydrogel powder) has been prepared. Swelling measurements of the synthesized hydrogels was carried out in various salt solutions and solutions with different pH. The results indicate that the hydrogels have good pH sensitivity and pH‐reversible property between pH 2 and pH 8. POLYM. ENG. SCI. 46:1778–1786, 2006. © 2006 Society of Plastics Engineers.     

pH sensitivity and swelling behavior of partially hydrolyzed formaldehyde-crosslinked poly(acrylamide) superabsorbent hydrogels

Poly(acrylamide) superabsorbent hydrogel was synthesized through crosslinking method. Formaldehyde was used as a crosslinking agent. To achieve a hydrogel with high swelling capacity, the resulted hydrogels were saponified using NaOH solution at high temperature. During saponification, ammonia gas is produced from hydrolysis reaction of amide groups. The arising of ammonia produces porous structure in hydrogels, which is confirmed using scanning electron microscopy. The conversion of amide groups to carboxylate groups was identified by FTIR spectroscopy. The reaction variables in both crosslinking and hydrolysis reactions that affect the swelling of hydrogels were optimized. The swelling of the hydrogels in various salt solutions with various valencies and radii was studied. Also, the absorbency under load was measured. The hydrogels exhibited pH-sensitivity characteristics. A sharp swelling change was observed in lieu of pH variations in a wide range (1–13). The swelling variations were explained according to the swelling theory based on the hydrogel chemical structure. The pH-reversibility and on–off switching behavior makes the intelligent hydrogels as good candidates for considering as potential drug carries. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Optimization of the preparation of a poly(aspartic acid) superabsorbent resin with response surface methodology

A poly(aspartic acid) superabsorbent resin was synthesized with polysuccinimide through chemical crosslinking with a crosslinking agent (diamine). The optimization of its preparation was investigated with response surface methodology. According to the Plackett–Burman design, the crosslinking temperature, drying temperature, and dissolving time of polysuccinimide had significant influences on the swelling ratio of the poly(aspartic acid) resin, which was the criterion for describing the water absorption capacity. Central composite design and response surface analysis were employed subsequently to further optimize the three aforementioned factors. A maximum swelling ratio greater than 500 g/g was attained; this was more than a 60% increase in comparison with previous results. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2616–2622, 2006     

水溶性Janus型POSS的设计合成及其对PAA/PAM水凝胶力学性能影响的研究

利用丙烯酰氧丙基多面体低聚倍半硅氧烷（Acrylo-POSS）和3-巯基-1-丙烷磺酸盐（MPS）之间的巯基点击反应，一步合成水溶性Janus型多面体低聚倍半硅氧烷（AS-POSS）。通过改变投料比可以调控AS-POSS的水溶性和双键与磺酸钠基团的物质的量比。将AS-POSS与丙烯酸（AA）和丙烯酰胺（AM）共聚制备了一系列不同AS-POSS含量的AS-POSS/PAA/PAM水凝胶，其中AS-POSS质量占单体总质量1%的1% AS-POSS/PAA/PAM水凝胶的平衡溶胀比达到512，断裂伸长率达到1074%，压缩强度为583 kPa，压缩应变为89%，屈服应变为330%，均大于对照组MBA/PAA/PAM水凝胶，表明AS-POSS的引入显著提高了水凝胶的溶胀度，明显增强了水凝胶的韧性、抗压缩性能和动态力学性能。AS-POSS/PAA/PAM水凝胶具有良好的导电性，离子电导率最高可达0.401 S/m。     

Mechanically robust and thermally enhanced sand-polyacrylamide-2D nanofiller composite hydrogels for water shutoff applications

Herein, we report a facile preparation method for mechanically robust and thermally enhanced sand-polyacrylamide (PAM)-2D-nanofillers composite hydrogels and their application in water shutoff. To prepare the sample, 4 wt% of aqueous PAM solution is mixed with organic cross-linkers of hydroquinone (HQ) and hexamethylenetetramine (HMT) in a 1:1 weight ratio and aqueous potassium chloride (KCl) solution and with a specific amount of 2D-nanofillers such as commercial graphene (CG) nanosheets or boron nitride nanoparticles (BN NPs). A specific amount of the above solution is added to sand, well mixed, and subsequently cured at 150°C for 8 h. The prepared composite hydrogels were characterized by Fourier-transform infrared spectroscopy (FT-IR) for chemical composition and X-ray diffraction (XRD) for successful hydrogel coating onto the sand particles. Thermal stabilities of the samples have been evaluated by differential scanning calorimetry (DSC). Mechanical properties (storage modulus [G′]; loss modulus [G″]; gel strength (G′/G″); and damping factor [G″/G′]) of the samples were determined using dynamic mechanical analyses. The thermal stability of the samples has reached as high as 193.4°C, while the gel strength is found to be a maximum of 16.2. The water swelling ratio for the composite hydrogel has reached a maximum of 1100% within 1 h.     

Temperature‐responsive characteristics of poly(N‐isopropylacrylamide) hydrogels with macroporous structure

Macroporous poly(N‐isopropylacrylamide) (PNIPA) hydrogels were synthesized by free‐radical crosslinking polymerization in aqueous solution from N‐isopropylacrylamide monomer and N,N‐methylenebis (acrylamide) crosslinker using poly(ethylene glycol) (PEG) with three different number‐average molecular weights of 300, 600 and 1000 g mol^?1 as the pore‐forming agent. The influence of the molecular weight and amount of PEG pore‐forming agent on the swelling ratio and network parameters such as polymer–solvent interaction parameter (χ) and crosslinking density (ν_E) of the hydrogels is reported and discussed. Scanning electron micrographs reveal that the macroporous network structure of the hydrogels can be adjusted by applying different molecular weights and compositions of PEG during polymerization. At a temperature below the volume phase transition temperature, the macroporous hydrogels absorbed larger amounts of water compared to that of conventional PNIPA hydrogels, and showed higher equilibrated swelling ratios in aqueous medium. Particularly, the unique macroporous structure provides numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to external temperature changes during the swelling and deswelling process. These macroporous PNIPA hydrogels may be useful for potential applications in controlled release of macromolecular active agents. Copyright © 2006 Society of Chemical Industry     

pH/temperature‐responsive semi‐IPN hydrogels composed of alginate and poly(N‐isopropylacrylamide)

Amino semitelechelic poly(N‐isopropylacrylamide) (PNIPAAm) was prepared by radical polymerization with aminoethanethiol hydrochloride as a chain‐transfer agent. Semi‐interpenetrating polymer network (semi‐IPN) hydrogels, composed of alginate and amine‐terminated PNIPAAm, were prepared by crosslinking with calcium chloride. From the swelling behaviors of semi‐IPNs at various pH's and Fourier transform infrared spectra at high temperatures, the formation of a polyelectrolyte complex was confirmed from the reaction between carboxyl groups in alginate and amino groups in modified PNIPAAm. Semi‐IPN hydrogels reached an equilibrium swelling state within 24 h. The water state in hydrogels, investigated by differential scanning calorimetry, showed that sample CAN55 [alginate/PNIPAAm (w/w) = 50/50] exhibited the lowest equilibrium water content and free water content among the hydrogels tested, which was attributed to its more compact structure compared to other samples and the high content of interchain bonding within the hydrogels. Alginate/PNIPAAm semi‐IPN hydrogels exhibited a reasonable sensitivity to the temperature, pH, and ionic strength of swelling medium. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1128–1139, 2002     

Property modulation of poly(N‐isopropylacrylamide) hydrogels by incorporation of modified silica

Poly(N‐isopropylacrylamide) (PNIPA)/silica composite hydrogels were prepared and the effects of the silica incorporation on the swelling and breaking characteristics of the hydrogels were investigated. To improve the dispersive property of silica in the PNIPA matrix via the formation of covalent bonds between the polymer and silica, vinyl groups were introduced in the silica by reacting it with a coupling agent, 3‐methacryloxypropyltrimethoxysilane. When unmodified silica was used as filler in the PNIPA‐composite hydrogel, the swelling ratio of the composite hydrogel below the critical gel transition temperature (CGTT) increased with increasing silica content. However, when the modified silica was used as the filler, the swelling ratio below CGTT decreased with increasing silica content because of the enhanced distribution and additional crosslinking. Above CGTT, the swelling ratios of the PNIPA/silica hydrogels were similar regardless of the silica modification. The gel breaking stress of the hydrogels increased with increasing silica content, and this enhancement was larger for the modified silica hydrogel. Scanning electron microscopy images showed that the modified silica particles were distributed more evenly in the PNIPA matrix than the unmodified ones were and that the size of cell‐like structure of the hydrogel decreased with increasing modified silica content. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Preparation and characterization of novel cationic copolymer hydrogels with pH sensitivity and thermosensitivity

Cationic hydrogels were synthesized through the copolymerization of N‐isopropylacrylamide and dimethylaminoethylmethacrylate. N,N′‐Methylenebisacrylamide was used as a crosslinking agent, and sodium bisulfite/ammonium persulfate was used as an initiator. The equilibrium and dynamic swelling properties were investigated to reveal the pH sensitivity and thermosensitivity of the hydrogels. The conclusion was drawn that the prepared cationic hydrogels demonstrated critical sensitivity at 37°C and pH 7.0–8.0 and that the stronger the acidity was of the buffered solution, the shorter the equilibrium swelling time was of the hydrogels. Drug‐release experiments in vitro were carried out at 37°C (close to body temperature), at pH 1.4 (close to the pH of the stomach), and at pH 7.4 (close to the pH of the intestine). The release results indicated that the drug (chloramphenicol) was released more rapidly from the prepared hydrogel in a pH 1.4 buffered solution than in a pH 7.4 one, and this was consistent with the results predicted from the experiments of the swelling kinetics. Moreover, the drug‐release process was confirmed by scanning electron micrographs of the hydrogels embedded with chloramphenicol. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3602–3608, 2006     

Effects of cyclization and pendant vinyl group reactivity on the swelling behavior of polyacrylamide gels

A series of polyacrylamide (PAAm) gels were prepared by free-radical crosslinking copolymerization of acrylamide and N,N′-methylenebis(acrylamide) (BAAm) in water at various crosslinker (BAAm) and chain transfer agent (isopropyl alcohol, IPA) concentrations. It was shown that only 5% of the crosslinker used in the feed forms effective crosslinks in the final hydrogels. At BAAm contents as high as 3 mole%, the equilibrium swelling ratio of the gels in water is independent of the crosslinker content in the feed. This is due to the prevailing multiple crosslinking reactions during the gel formation process. At a fixed crosslinker content, the onset of gelation is shifted towards higher conversions and reaction times as the amount of IPA increases. Addition of IPA in the monomer mixture also increases the equilibrium swelling ratio of PAAm gels. It was shown that the gel crosslinking density increases on rising IPA concentration in the feed due to the increasing rate of intermolecular crosslinking reactions. Received: 30 May 1997/Accepted: 26 June 1997     

京尼平交联大豆蛋白/壳聚糖复合凝胶的控释

利用天然无毒的京尼平交联大豆蛋白(SB)和壳聚糖(CS)制备复合水凝胶(HD)并用作茶碱的控释载体。同时对其在模拟胃肠液和pH7.4缓冲液（PBS）中的控释特性进行了研究。结合扫描电镜和红外光谱以及核磁共振表征了复合凝胶的表观形态和结构。结果表明,复合水凝胶中大豆蛋白和壳聚糖通过京尼平发生了明显的交联作用,并呈现致密的片层结构。复合凝胶在模拟胃肠液和pH7.4PBS中均呈现溶胀现象,在模拟胃液中的溶胀度较低。而且凝胶在pH1.2模拟胃液中的释放量比模拟肠液和pH7.4PBS液中的低,并发现该凝胶具有pH响应,在120 h内可实现对茶碱的可控释放。因此,这种京尼平交联的复合凝胶具有作为药物在胃肠道中定向运送载体的潜力。     

Thermosensitive Poly(N-isopropylacrylamide-co-acrylonitrile) Hydrogels with Rapid Response

Acrylonitrile （AN） was copolymerized with N-isopropylacrylamide （NIPA） to synthesize thermosensitive hydrogels, and the on-off switch behavior of poly（NIPA-co-AN） hydrogels with different fraction of hydrophobic component （AN） was investigated. It is found that the lower critical solution temperature （LCST）, the swelling ratio at certain temperature and the reswelling rate of poly（NIPA-co-AN） hydrogels decreased as AN unit fraction in copolymers increased. In order to improve the responsive rate of poly（NIPA-co-AN） hydrogels, they were further treated by surface crosslinking using N, N′-methylene bisacrylamide （BIS） as a crosslinking agent. The swelling and deswelling behaviors of these copolymers were compared with those of the untreated hydrogels. The results indicated that the responsive rate of poly（NIPA-co-AN） hydrogel was improved by surface crosslinking. The resulting hydrogels bearing cyano groups with fast response have potential applications in the field of drug-controlled release and immobilization of biomolecules.     

Porous Carrageenan-<Emphasis Type="Italic">g</Emphasis>-polyacrylamide/bentonite superabsorbent composites: swelling and dye adsorption behavior

A novel superabsorbent composite based on kappa-Carrageenan (κC) was prepared by graft copolymerization of acrylamide (AAm) onto κC in the presence of bentonite powder using methylenebisacrylamide (MBA) as a crosslinking agent, ammonium persulfate (APS) as an initiator, and sodium carbonate as a pore-forming agent. The swelling behavior in distilled water and in solutions with different pH values was investigated. The results indicated that with increasing carrageenan/bentonite weight ratio, the swelling capacity is increased but the gel content is decreased. The swelling rate of the hydrogels was improved by introducing sodium carbonate as pore-forming agent. The prepared superadsorbent composites were used as adsorbent for a cationic dye, methylene blue. Isotherm of adsorption and the effect of pH, adsorption dosage, contact time and initial dye concentration on dye adsorption were also studied. The results showed that maximum adsorption capacity of methylene blue on the prepared adsorbents is 156.25 mg g^?1 and adsorption is well-described by Langmuir isotherm model.