Epoxidized natural rubber/epoxy blends: Phase morphology and thermomechanical properties

Epoxidized natural rubbers (ENRs) were prepared. ENRs with different concentrations of up to 20 wt % were used as modifiers for epoxy resin. The epoxy monomer was cured with nadic methyl anhydride as a hardener in the presence of N,N‐dimethyl benzyl amine as an accelerator. The addition of ENR to an anhydride hardener/epoxy monomer mixture gave rise to the formation of a phase‐separated structure consisting of rubber domains dispersed in the epoxy‐rich phase. The particle size increased with increasing ENR content. The phase separation was investigated by scanning electron microscopy and dynamic mechanical analysis. The viscoelastic behavior of the liquid‐rubber‐modified epoxy resin was also evaluated with dynamic mechanical analysis. The storage moduli, loss moduli, and tan δ values were determined for the blends of the epoxy resin with ENR. The effect of the addition of rubber on the glass‐transition temperature of the epoxy matrix was followed. The thermal stability of the ENR‐modified epoxy resin was studied with thermogravimetric analysis. Parameters such as the onset of degradation, maximum degradation temperature, and final degradation were not affected by the addition of ENR. The mechanical properties of the liquid‐natural‐rubber‐modified epoxy resin were measured in terms of the fracture toughness and impact strength. The maximum impact strength and fracture toughness were observed with 10 wt % ENR modified epoxy blends. Various toughening mechanisms responsible for the enhancement in toughness of the diglycidyl ether of the bisphenol A/ENR blends were investigated. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39906.     

Thermoplastic vulcanizates based on poly(methyl methacrylate)/epoxidized natural rubber blends: Mechanical,thermal, and morphological properties

Epoxidized natural rubbers (ENRs) with epoxide levels of 10, 20, 30, 40 and 50 mol % were prepared. The ENRs were later used to prepare thermoplastic vulcanizates (TPVs) by blending them with poly(methyl methacrylate) (PMMA) using various formulations. Dynamic vulcanization, using sulfur as a vulcanizing agent, was performed during the mixing process. The mixing torque increased as the ENR contents and epoxide molar percentage increased. This was because of an increasing chemical interaction between the polar groups of the blend components, particularly at the interface between the elastomeric and thermoplastic phases. The ultimate tensile strength of the TPVs with ENR‐20 was high because of strain‐induced crystallization. ENRs with epoxide levels >30 mol % exhibited an increase of tensile strength because of increasing levels of chemical interaction between the molecules and the different phases. The hardness of the TPVs also increased with increased epoxide levels but decreased with increased contents of ENRs. Two morphology phases with small domains of vulcanized ENR particles dispersed in the PMMA matrix were observed from scanning electron microscopy micrographs. The TPVs based on ENR‐20 and ENR‐50 showed smaller dispersed rubber domains than those of the other types of ENRs. Furthermore, the size of the vulcanized rubber domain decreased with increasing amounts of PMMA in the blends. The decomposition temperature of the TPVs also increased as both the levels of ENRs in the blends and the epoxide molar percentage increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1251–1261, 2005     

Thermoplastic vulcanizates based on epoxidized natural rubber/polypropylene blends: Effect of epoxide levels in ENR molecules

Epoxidized natural rubbers (ENR) with various levels of epoxide groups were prepared. Thermoplastic vulcanizates based on 75/25 ENRs/PP blends with Ph‐PP compatibilizer were later prepared by dynamic vulcanization using sulfur curing system. Influence of various levels of epoxide groups on rheological, mechanical morphological properties, and swelling resistance of the TPVs was investigated. It was found that the mixing torque, apparent shear stress, apparent shear viscosity, tensile strength, and hardness properties increased with increasing levels of epoxide groups in the ENR molecules. This may be attributed to increasing level of chemical interaction between the methylol groups of the Ph‐PP molecules and polar functional groups of the ENR molecules. Also, the PP segments in the Ph‐PP molecules are capable of compatibilizing with the PP molecules used as a blend composition. In SEM micrographs, we observed finer dispersion of vulcanized rubber domains as increasing levels of epoxide contents. This corresponds to increasing trend of strength and hardness properties of the TPVs. An increasing trend of tension set and a decreasing trend of elongation at break were observed as increasing levels of epoxide groups in the ENR molecules. This is because of higher rigidity of the vulcanized ENR phase with higher epoxide groups. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3046–3052, 2006     

Epoxy‐tert‐butyl poly(cyanoarylene ether) blends: Phase morphology,fracture toughness,and mechanical properties

Tert‐butyl hydroquinone–based poly(cyanoarylene ether) (PENT) was synthesized by the nucleophilic aromatic substitution reaction of 2,6‐dichlorobenzonitrile with tert‐butyl hydroquinone using N‐methyl‐2‐pyrrolidone (NMP) as solvent in the presence of anhydrous potassium carbonate in a nitrogen atmosphere at 200°C. PENT‐toughened diglycidyl ether of bisphenol A epoxy resin (DGEBA) was developed using 4,4′‐diaminodiphenyl sulfone (DDS) as the curing agent. Scanning electron micrographs revealed that all blends had a two‐phase morphology. The morphology changed from dispersed PENT to a cocontinuous structure with an increase in PENT content in the blends from 5 to 15 phr. The viscoelastic properties of the blends were investigated using dynamic mechanical thermal analysis. The storage modulus of the blends was less than that of the unmodified resin, whereas the loss modulus of the blends was higher than that of the neat epoxy. The tensile strength of the blends improved slightly, whereas flexural strength remained the same as that of the unmodified resin. Fracture toughness was found to increase with an increase in PENT content in the blends. Toughening mechanisms like local plastic deformation of the matrix, crack path deflection, crack pinning, ductile tearing of thermoplastic, and particle bridging were evident from the scanning electron micrographs of failed specimens from the fracture toughness measurements. The thermal stability of the blends were comparable to that of the neat resin. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3536–3544, 2006     

Oil resistance and physical properties of in situ epoxidized natural rubber from high ammonia concentrated latex

Epoxidized natural rubber (ENR) was prepared via in situ epoxidation from high ammonia concentrated natural rubber latex with formic acid and hydrogen peroxide in the presence of a surfactant at 50°C for 4, 8, and 12 h. The obtained ENRs containing 20, 45, and 65 mol % of expoxide groups were denoted ENR20, ENR45, and ENR65, respectively. The differential scanning calorimetric study revealed that they exhibited higher glass transition temperatures than that of natural rubber (?62.4°C), at ?38.2°C for ENR20, ?27.8°C for ENR45, and ?19.7°C for ENR 65. It was clearly seen that their glass transition temperatures increased as the amount of epoxide groups increased. The prepared ENRs were compounded and vulcanized to prepare test specimens for determination of oil resistance and various physical properties. It was found that the swelling of ENRs in oils was substantially less than that of natural rubber. The oil resistance of ENR65 was comparable to that of nitrile rubber, commonly used as oil resistant rubber. ENR65 also showed higher hardness than other ENRs. Contrarily, ENR20 possessed superior tensile strength and compression set when compared with other ENRs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3948–3955, 2006     

Rheological and thermal properties of thermoplastic natural rubbers based on poly(methyl methacrylate)/epoxidized‐natural‐rubber blends

Epoxidized natural rubbers (ENRs) with epoxide levels of 10, 20, 30, 40, and 50 mol % were prepared. The ENRs were later blended with poly(methyl methacrylate) (PMMA) with various blend formulations. The mixing torque of the blends was observed. The torque increased as the PMMA contents and epoxide molar percentage increased in the ENR molecules. Furthermore, the shear stress and shear viscosity of the polymer blends in the molten state increased as the ENR content and epoxide molar percentage increased in the ENR molecules. Chemical interactions between polar groups in the ENR and PMMA molecules might be the reason for the increases in the torque, shear stress, and viscosity. All the ENR/PMMA blends exhibited shear‐thinning behavior. This was observed as a decrease in the shear viscosity with an increase in the shear rate. The power‐law index of the blends decreased as the ENR contents and epoxide molar percentage increased in the ENR molecules. However, the consistency index (or zero shear viscosity) increased as the ENR contents and epoxide molar percentage increased. A two‐phase morphology was observed with scanning electron microscopy. The small domains of the minor components were dispersed in the major phase. For the determination of blend compatibility, two distinct glass‐transition‐temperature (T_g) peaks from the tan δ/temperature curves were found. Shifts in T_g to a higher temperature for the elastomeric phase and to a lower temperature for the PMMA phase were observed. Therefore, the ENR/PMMA blends could be described as partly miscible blends. According to the thermogravimetry results, the decomposition temperatures of the blends increased as the levels of ENR and the epoxide molar percentage increased. The chemical interactions between the different phases of the blends could be the reason for the increase. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3561–3572, 2004     

动态固化聚丙烯／马来酸酐接枝聚丙烯／滑石粉／环氧树脂复合材料研究

将动态硫化技术应用于热塑性树脂／填料／热固性树脂复合体系，制备了动态固化聚丙烯(PP)／马来酸酐接枝PP(PP-g-MAH)/滑石粉(Talc)／环氧树脂(EP)复合材料。研究了动态固化PP／PP-g-MAH/Talc／EP复合材料的界面作用、形态结构、力学性能以及热稳定性。实验结果表明：PP／PP-g—MAH的加入，可明显增加PP/Talc复合材料的界面作用。在动态固化PP／PP-g-MAH/Talc／EP复合材料中，PP和Talc两相界面更加模糊，动态固化EP进一步增加了PP和Talc间的界面作用。当EP的用量超过5份时，部分EP呈颗粒状分布在PP基体中。与PP／PP-g-MAH/Talc／EP和PP／PP-MAH-Talc／EP复合材料相比，动态固化PP／PP-g-MAH/Talc／EP复合材料的冲击强度、拉伸强度和弯曲模量均有明显提高。当EP用量超过5份时，复合材料的冲击强度和断裂伸长率明显降低，但拉伸强度和弯曲模量继续增加。热分析表明动态固化PP／PP-g-MAH/Talc／EP复合材料具有较高的热稳定性。     

The effect of epoxide content on compatibility of poly(lactic acid)/epoxidized natural rubber blends

The objective of this work was to determine the effect of the epoxide content in epoxidized natural rubber (ENR) on the miscibility and compatibility with poly(lactic acid) (PLA) in prepared PLA/ENR blends. PLA was blended with 10 wt% of ENRs (epoxidized at 10, 15, 20, and 25 mol%). The presented study showed that the in situ graft copolymer, PLA-g-ENR, was formed during melt blending in the blends containing 10 and 15 mol% ENR. This work is the initial study showing the presence of PLA-g-ENR in the blends by ¹H-NMR and ¹³C-NMR. PLA-g-ENR acted as a compatibilizer, producing a partially miscible blend, indicated by an inward shift of the α-transition temperatures of PLA and ENR in the blends. PLA-g-ENR also greatly reduced the particle size of ENR and increased the impact strength, tensile strength, and elongation at break of the blends. The epoxide content of ENR changed deformation mechanisms of the blends.     

Peel and shear strength of pressure‐sensitive adhesives prepared from epoxidized natural rubber

Peel and shear strength of two grades of epoxidized natural rubber (ENR 25 and ENR 50)‐based pressure‐sensitive adhesive was studied. Coumarone‐indene resin was used as the tackifier, whereas toluene was chosen as the solvent throughout the experiment. The tackifier loading was varied from 0 to 80 parts per hundred parts of rubber (phr). A SHEEN hand coater was used to coat the adhesive on substrate to give a coating thickness of 30, 60, 90, and 120 μm. Peel strength and shear strength of the adhesive were determined by using a Lloyd adhesion tester and Texture analyzer, respectively. Results show that maximum peel strength occurs at 40 phr of coumarone‐indene resin for both ENRs studied an observation, which is attributed to the maximum wettability of the substrate. However, the shear strength shows a gradual decrease with increasing tackifier loading because of the decrease in cohesive strength of adhesive. ENR 25 consistently indicates higher peel strength and shear strength than ENR 50. Generally, peel and shear strength increases with coating thickness. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007.     

Nanosilica‐reinforced Epoxidized natural rubber nanocomposites: Effect of Epoxidation level on morphological and mechanical properties

Epoxidized natural rubbers (ENRs) with three different epoxide contents (i.e., 20, 35, and 50 mol% indicated as ENR20, ENR35, and ENR50, respectively) were prepared. They were then reinforced with 3‐methyacryloxypropyl trimethoxysilane‐modified nanosilica (MPTS‐SiO₂). Influence of epoxide level in ENR molecules on morphological, mechanical, and dynamic mechanical properties of the ENR nanocomposites was investigated. The scanning electron microscopy results revealed larger agglomerates of SiO₂ were found in the ENR composites with higher epoxide content. Furthermore, the strength and moduli of the ENR nanocomposites increased with increasing epoxide content. However, the optimal tensile strength and elongation at break were observed in the nanocomposites with the intermediate level of epoxide contents. The correlation between the strength properties and the interfacial silica‐matrix adhesion indicated that the maximum interfacial adhesion of the nanocomposites was observed in the nanocomposite with ENR35. Also, DMA results indicated stronger interaction between ENR35 and MPTS‐SiO₂ due to higher storage modulus. POLYM. COMPOS., 38:1151–1157, 2017. © 2015 Society of Plastics Engineers     

Enhancement of PVC/ENR blend properties by poly(methyl acrylate) grafted oil palm empty fruit bunch fiber

Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150°C, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Young's modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Young's modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the impact strength, UTS, and elongation at break of the composites were found to decrease with the increase in fiber loading. An increase in elongation at break and UTS and decrease in the flexural and Young's modulus was observed with the addition of PMA‐g‐OPEFB fiber compared to ungrafted fiber. This observation indicates that grafting of PMA onto OPEFB impart some flexibility to the blend. The morphology of cryogenically fractured and tensile fracture surfaces of the composites, examined by a scanning electron microscope shows that the adhesion between the fiber and the matrix is improved upon grafting of the OPEFB fiber. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

间苯二酚二缩水甘油醚的制备及其应用

采用三苯基磷作醚化催化剂,粉状氢氧化钠作闭环剂合成了间苯二酚二缩水甘油醚(RDGE),其环氧值为0.80,在25℃时粘度为0.36 Pa.s,示差扫描量热仪(DSC)检测表明,其固化放热峰比双酚A型环氧树脂(E51)降低了约15℃。RDGE对E51有非常显著的稀释作用,二者共混,大大提高了通用环氧树脂的综合性能。采用593#固化剂时,RDGE和E51的拉伸强度分别为75.17 MPa和58.58 MPa,前者比后者高出28%,RDGE与E51共混固化物的拉伸强度随RDGE含量的增加而呈线性增加;593#固化的RDGE/E51共混体系,弯曲强度和弯曲模量均随RDGE用量的增加而呈线性增加,弯曲强度由E51的112.77 MPa增加到RDGE的123.75 MPa,弯曲模量由E51的1.79 GPa增加到RDGE的2.40 GPa。     

炭黑/煤矸石/碳纳米管复合填料体系对天然橡胶性能的影响研究*

利用硝酸氧化法对碳纳米管(CNTs)进行纯化,并用环氧天然橡胶(ENR)进行改性处理。结合胶质量分数测定结果表明, ENR用量15%(质量)时效果最佳。采用胶乳凝聚法制备CNTs/天然橡胶(NR)母料。煤矸石粉(CG)经高温煅烧和表面改性处理。 将CNTs/天然橡胶(NR)母料、CG和炭黑(CB)通过机械混炼法与天然橡胶及配合剂混合,制备CB/CG/CNTs/NR复合材料,并对复合材料进行硫化特性及物理机械性能。结果表明： CNTs延迟硫化效应明显;相比炭黑,CG对硫化具有促进作用。硫化特性和甲苯溶胀法测定结果表明,在填料份数相同的条件下,单独由CB填充的NR有最大的交联密度,CNTs对交联密度影响不明显。物理机械性能测试结果表明,当CG：CB：CNTs=17.5:16.5:1(Phr)时,NR硫化胶的300%定伸应力和扯断伸长率明显高于单独由CB填充NR,而拉伸强度与之接近,复合填料样填充NR具有较好的综合性能。扫描电镜测试结果表明,复合填料在NR基体中分布均匀。     

Mechanical properties of blocked polyurethane/epoxy interpenetrating polymer networks

The mechanical properties of blocked polyurethane(PU)/epoxy interpenetrating polymer networks (IPNs) were studied by means of their static and damping properties. The studies of static mechanical properties of IPNs are based on tensile properties, flexural properties, hardness, and impact method. Results show that the tensile strength, flexural strength, tensile modulus, flexural modulus, and hardness of IPNs decreased with increase in blocked PU content. The impact strength of IPNs increased with increase in blocked PU content. It shows that the tensile strength, flexural strength, tensile modulus, and flexural modulus of IPNs increased with filler (CaCO₃) content to a maximum value at 5, 10, 20, and 25 phr, respectively, and then decreased. The higher the filler content, the greater the hardness of IPNs and the lower the notched Izod impact strength of IPNs. The glass transition temperatures (T_g) of IPNs were shifted inwardly compared with those of blocked PU and epoxy, which indicated that the blocked PU/epoxy IPNs showed excellent compatibility. Meanwhile, the T_g was shifted to a higher temperature with increasing filler (CaCO₃) content. The dynamic storage modulus (E′) of IPNs increased with increase in epoxy and filler content. The higher the blocked PU content, the greater the swelling ratio of IPNs and the lower the density of IPNs. The higher the filler (CaCO₃) content, the greater the density of IPNs, and the lower the swelling ratio of IPNs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1826–1832, 2006     

Synthesis of EP‐POSS mixture and the properties of EP‐POSS/epoxy,SiO2/epoxy,and SiO2/EP‐POSS/epoxy nanocomposite

The hybrid material of EP‐POSS mixture was synthesized by the hydrolysis and condensation of (γ‐glycidoxypropyl) trimethoxysilane. A series of binary systems of EP‐POSS/epoxy blends, epoxy resin modified by silica nanoparticles (SiO₂/epoxy), and ternary system of SiO₂/EP‐POSS/epoxy nanocomposite were prepared. The dispersion of SiO₂ in the matrices was evidenced by transmission electron micrograph, and the mechanical properties, that is, flexural strength, flexural modulus, and impact strength were examined for EP‐POSS/epoxy blends, SiO₂/epoxy, and SiO₂/EP‐POSS/epoxy, respectively. The fractured surface of the impact samples was observed by scanning electron micrograph. Thermogravimetry analysis were applied to investigate the different thermal stabilities of the binary system and ternary system by introducing EP‐POSS and SiO₂ to epoxy resin. The results showed that the impact strength, flexural strength, and modulus of the SiO₂/EP‐POSS/epoxy system increased around by 57.9, 14.1, and 44.0% compared with the pure epoxy resin, T_i, T_max and the residues of the ternary system were 387°C, 426°C, and 25.2%, increased remarkably by 20°C, 11°C and 101.6% in contrast to the pure epoxy resin, which was also higher than the binary systems. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 810‐819, 2013     

A new latent accelerator and study of its effect on physical,mechanical and shelf-life of carbon fiber epoxy prepreg

The effects of a new latent accelerator and those of two common accelerators of 1-methyl imidazole and 2,4,6-tris(dimethylaminomethyl)phenol (DMP) have been studied in relation to the properties of dicyandiamide (dicy) cured epoxy resin and its prepregs with unidirectional carbon fiber. The new prepared accelerator is an adduct based on DMP (A_DMP). The results showed that the curing behavior of epoxy/dicy did not change when the appropriate amount of new accelerator was used. The amount of 5 phr of new latent accelerator is equal to the amount of 0.6 phr of DMP accelerator and by increasing the amount of new accelerator, the curing reaction of epoxy/dicy increased significantly. Viscosity build-up results and gel time measurements showed the high pot-life of resin system (epoxy/Dicy/A_DMP) and the high shelf-life of their prepreg. The results showed that the lap shear strength of sample containing 5 phr of the new accelerator (A_DMP5) was increased by 127% in comparison to the sample containing 0.6 phr of DMP. Transverse tensile strength and strain-at-break were increased by 27% and 31.7%, respectively. Transverse flexural strength, flexural strain-at-break and flexural modulus increased by 52%, 11% and 60%, respectively. On the other hand, fracture toughness and fracture energy increased significantly by 214% and 700%, respectively. This increase in mechanical properties was due to the bulkiness of the new latent accelerator acting as a toughening agent and also the good adhesion of fiber to the matrix as revealed by scanning electron microscopy.

     

呋喃/环氧/胺类固化剂共混体系的固化反应机理及性能研究

采用溶液法制备了呋喃/环氧树脂/胺类固化剂的共混物。采用粘度测试仪、DSC、FT-IR、力学测试仪、SEM对共混体系的加工性、固化反应机理及固化后样品的力学性能及机理进行了研究。研究结果揭示了共混体系的固化反应机理,发现在共混体系中呋喃树脂与部分环氧树脂可以在180℃附近反应,剩余部分环氧树脂需要在更高的温度下才能进一步完全反应。共混体系具有优异的力学性能,且随着共混体系中环氧树脂含量的增多在逐渐升高,其中弯曲强度最高达到113 MPa,弯曲模量最高达到4129 MPa,冲击强度最高达到19.1kJ/m~2。对冲击断口形貌进行观察,发现共混体系浇铸体具有相分离结构是性能优异的主要原因。     

Mechanical and thermal properties of bisphenol A-based cyanate ester and diallyl phthalate blends

Cyanate ester resins are a high performance class of compounds. They have excellent mechanical properties, dielectric properties and thermal properties; however, their major drawback is their brittleness. An attempt was made to improve the impact strength of the cyanate ester resin. In the present study a commonly used cyanate resin, bisphenol A dicyanate (BADCy), was modified by the addition of diallyl phthalate (DAP) and was cured with benzoyl peroxide. The properties of the blends such as thermal and mechanical properties were investigated in detail by scanning electron microscope, dynamic mechanical analysis, thermogravimetric analysis, and mechanical measurement. The results indicate that the addition of the appropriate amount of DAP can effectively improve the impact toughness and the flexural strength while sacrificing the thermal properties of the blends. The maximum impact strength and flexural strength were observed on addition of 15 phr DAP content. However, the thermal stability of the blends was found to be lower than that of the unmodified BADCy resin.     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

Correlation between stress-whitening and fracture toughness in rubber-modified epoxies

Fracture toughness of rubber modified epoxy systems was evaluated in relation to stresswhitening. The epoxy systems consisted of diglycidyl ethers of bisphenol A (DGEBA)-based epoxy resin, 4,4′ diaminodiphenyl sulphone (DDS) as curing agent, and carboxylterminated butadiene-acrylonitrile (CTBN) rubber. It was found that a peak value of fracture toughness occurs at a small amount of rubber content (∼ 4 phr) and closely corresponds to that of stress-whitening size. Other properties such as flexural strength and flexural modulus were also found to display maxima at a similar amount of rubber content. © 1996 John Wiley & Sons, Inc.