CMOS fully-differential bandpass ΣΔ modulator usingswitched-current circuits

The authors present a fourth-order bandpass ΣΔ switched-current modulator IC in 0.8 μm CMOS single-poly technology. It is the first reported integrated circuit realisation of a bandpass ΣΔ modulator using switched-current circuits. Its architecture is obtained by applying a lowpass to bandpass transformation (z¹→-z²) to a second-order lowpass modulator. It has been realised using fully-differential circuitry with common-mode feedback. Measurements show 8 bit dynamic range up to 5 MHz clock frequency     

A 1.8-mW CMOS ΣΔ modulator with integrated mixer forA/D conversion of IF signals

In this paper, the design of a continuous-time baseband sigma-delta (ΣΔ) modulator with an integrated mixer for intermediate-frequency (IF) analog-to-digital conversion is presented. This highly linear IF ΣΔ modulator digitizes a GSM channel at intermediate frequencies up to 50 MHz. The sampling rate is not related to the input IF and is 13.0 MHz in this design. Power consumption is 1.8 mW from a 2.5-V supply. Measured dynamic range is 82 dB, and third-order intermodulation distortion is -84 dB for two -6-dBV IF input tones. Two modulators in quadrature configuration provide 200-kHz GSM bandwidth. Active area of a single IF ΣΔ modulator is 0.2 mm² in 0.35-μm CMOS     

Quadrature bandpass ΔΣ modulation for digital radio

A quadrature bandpass ΔΣ modulator IC facilitates monolithic digital-radio-receiver design by allowing straightforward “complex A/D conversion” of an image reject mixer's I and Q, outputs. Quadrature bandpass ΔΣ modulators provide superior performance over pairs of real bandpass ΔΣ modulators in the conversion of complex input signals, using complex filtering embedded in ΔΣ loops to efficiently realize asymmetric noise-shaped spectra. The fourth-order prototype IC, clocked at 10 MHz, converts narrowband 3.75-MHz I and Q inputs and attains a dynamic range of 67 dB in 200-kHz (GSM) bandwidth, increasing to 71 and 77 dB in 100- and 30-kHz bandwidths, respectively. Maximum signal-to-noise plus distortion ratio (SNDR) in 200-kHz bandwidth is 62 dB. Power consumption is 130 mW at 5 V. Die size in a 0.8-μm CMOS process is 2.4×1.8 mm²      

A double-sampling pseudo-two-path bandpass ΔΣ modulator

A double-sampling pseudo-two-path bandpass ΔΣ modulator is proposed. This modulator has an output rate equal to twice the clock rate, uses n/2 operational amplifiers (op-amps) for an nth-older noise transfer function, and has reduced clock feedthrough in the signal path band. The required clocks can be simpler to implement than the conventional pseudo-two-path techniques. The measured signal-to-noise ratio and dynamic range of the fourth-order double-sampling pseudo-two-path bandpass ΔΣ modulator in a 30-kHz bandwidth at a center frequency of 2.5 MHz (at a clock frequency of 5 MHz) are 62 and 68 dB, respectively     

标准数字工艺下16位精度低压低功耗ΣΔ模数调制器设计

针对输入信号频率在20 Hz～24 kHz范围的音频应用,该文采用标准数字工艺设计了一个1.2 V电源电压16位精度的低压低功耗ΣΔ模数调制器。在6 MHz采样频率下,该调制器信噪比为102.2 dB,整个电路功耗为2.46 mW。该调制器采用一种伪两级交互控制的双输入运算放大器构成各级积分器,在低电源电压情况下实现高摆率高增益要求的同时不会产生更多功耗。另外,采用高线性度、全互补MOS耗尽电容作为采样、积分电容使得整个电路可以采用标准数字工艺实现,从而提高电路的工艺兼容性、降低电路成本。与近期报道的低压低功耗ΣΔ模数调制器相比,该设计具有更高的品质因子FOM。     

A CMOS monolithic ΔΣ-controlled fractional-N frequencysynthesizer for DCS-1800

A monolithic 1.8-GHz ΔΣ-controlled fractional-N phase-locked loop (PLL) frequency synthesizer is implemented in a standard 0.25-μm CMOS technology. The monolithic fourth-order type-II PLL integrates the digital synthesizer part together with a fully integrated LC VCO, a high-speed prescaler, and a 35-kHz dual-path loop filter on a die of only 2×2 mm². To investigate the influence of the ΔΣ modulator on the synthesizer's spectral purity, a fast nonlinear analysis method is developed and experimentally verified. Nonlinear mixing in the phase-frequency detector (PFD) is identified as the main source of spectral pollution in ΔΣ fractional-N synthesizers. The design of the zero-dead zone PFD and the dual charge pump is optimized toward linearity and spurious suppression. The frequency synthesizer consumes 35 mA from a single 2-V power supply. The measured phase noise is as low as -120 dBc/Hz at 600 kHz and -139 dBc/Hz at 3 MHz. The measured fractional spur level is less than -100 dBc, even for fractional frequencies close to integer multiples of the reference frequency, thereby satisfying the DCS-1800 spectral purity constraints     

A low oversampling ratio 14-b 500-kHz ΔΣ ADC with aself-calibrated multibit DAC

Delta-sigma (ΔΣ) analog-to-digital converters (ADC's) rely on oversampling to achieve high-resolution. By applying multibit quantization to overcome stability limitations, a circuit topology with greatly reduced oversampling requirements is developed. A 14-bit 500-kHz ΔΣ ADC is described that uses an oversampling ratio of only 16. A fourth-order embedded modulator, four-bit quantizer, and self-calibrated digital-to-analog converter (DAC) are used to achieve this performance. Although the high-order embedded architecture was previously thought to be unstable, it is shown that with proper design, a robust system can be obtained. Circuit design and implementation in a 1.2-μm CMOS process are presented. Experimental results give a dynamic range of 84 dB with a sampling rate of 8 MHz and oversampling ratio of 16. This is the lowest oversampling ratio for this resolution and bandwidth achieved to date     

A 13.5-mW 185-Msample/s ΔΣ modulator for UMTS/GSMdual-standard IF reception

A system-oriented approach for the design of a UMTS/GSM dual-standard ΔΣ modulator is presented to demonstrate the feasibility of achieving intermediate frequency (IF) around 100 MHz, high dynamic range, and low power consumption at the same time. The circuit prototype implements 78 MHz IF for GSM and 138.24 MHz for wideband code division multiple access (WCDMA), which are set to be 3/4 of the analog-to-digital converter sampling rate. A two-path IF sampling and mixing topology with a low-pass ΔΣ modulator, run at half the sampling rate, is used. Implemented in 0.25-μm CMOS, the circuit achieves dynamic range and peak signal-to-noise and distortion ratio for GSM of 86 and 72 dB, respectively. The corresponding values for WCDMA are 54 and 52 dB, respectively. Optimization is performed at all stages of design to minimize power consumption. The complete circuit consumes less than 11.5 mW for GSM and 13.5 mW for WCDMA at 2.5-V supply, of which 8 mW is due to the analog part     

Switched-Current bandpass Sigma–Delta modulators for AM digital radio receivers

This paper discusses the use of switched-current (SI) circuits to design Band-Pass ΣΔ Modulators (BP-ΣΔMs) suitable for AM digital radio receivers. First of all, the paper briefly outlines the concept and principles of BP-ΣΔMs, and introduces two modulator architectures which are obtained by applying a lowpass-to-bandpass transformation (i.e. z⁻¹→−z⁻²) to a first-order and a second-order Low-Pass ΣΔ Modulator (LP-ΣΔM), respectively. The resulting BP-ΣΔMs, respectively of second-order and of fourth-order, are then used as case studies for SI circuit implementation. Systematic analysis of the errors associated to SI circuits is carried out and models are presented to evaluate their incidence on the performance of BP-ΣΔMs; the significance of the different errors is illustrated via the two selected case studies. Fully-differential regulated-folded cascode SI memory cells are chosen to attenuate these errors. Based on the proposed error models, optimization is carried out to fulfill AM radio requirements in practical modulator implementations. Two IC prototypes have been fabricated in a CMOS 0.8 μm technology, and measured, to validate the presented design methodology. One of these prototypes uses the fourth-order architecture to digitize AM signals, and features 10.5-bit resolution with 60 mW power consumption from a 5 V supply voltage. The other uses the second-order architecture and features 8-bit with 42 mW in the commercial AM band, from 540 to 1600 kHz. Experimental results show correct noise-shaping for sampling frequencies up to 16 MHz, which means a significant operation frequency enhancement as compared to previously reported SI ΣΔ Modulators.     

A 13-bit, 2.2-MS/s, 55-mW multibit cascade ΣΔ modulatorin CMOS 0.7-μm single-poly technology

This paper presents a CMOS 0.7-μm ΣΔ modulator IC that achieves 13-bit dynamic range at 2.2 MS/s with an oversampling ratio of 16. It uses fully differential switched-capacitor circuits with a clock frequency of 35.2 MHz, and has a power consumption of 55 mW. Such a low oversampling ratio has been achieved through the combined usage of fourth-order filtering and multibit quantization. To guarantee stable operation for any input signal and/or initial condition, the fourth order shaping function has been realized using a cascade architecture with three stages; the first stage is a second-order modulator, while the others are first-order modulators-referred to as a 2-1-1_mb architecture. The quantizer of the last stage is 3 bits, while the other quantizers are single bit. The modulator architecture and coefficients have been optimized for reduced sensitivity to the errors in the 3-bit quantization process. Specifically, the 3-bit digital-to-analog converter tolerates 2.8% FS nonlinearity without significant degradation of the modulator performance. This makes the use of digital calibration unnecessary, which is a key point for reduced power consumption. We show that, for a given oversampling ratio and in the presence of 0.5% mismatch, the proposed modulator obtains a larger signal-to-noise-plus-distortion ratio than previous multibit cascade architectures. On the other hand, as compared to a 2.1.1_single-bit modulator previously designed for a mixed-signal asymmetrical digital subscriber line modem in the same technology, the modulator in this paper obtains one more bit resolution, enhances the operating frequency by a factor of two, and reduces the power consumption by a factor of four     

A 900-mV low-power ΔΣ A/D converter with 77-dB dynamicrange

The design of a low-voltage and low-power ΔΣ analog-to-digital (A/D) converter is presented. A third-order single-loop ΔΣ modulator topology is implemented with the differential modified switched op-amp technique. The modulator topology has been transformed as to accommodate half-delay integrators. Dedicated low-voltage circuit building blocks, such as a class AB operational transconductance amplifier, a common-mode feedback amplifier, and a comparator are treated, as well as low-voltage design techniques. The influence of very low supply voltage on power consumption is discussed. Measurement results of the 900-mV ΔΣ A/D converter show a 77-dB dynamic range in a 16-kHz bandwidth and a 62-dB peak signal-to-noise ratio for a 40-μW power consumption     

Architecture, design, and test of continuous-time tunableintermediate-frequency bandpass delta-sigma modulators

This paper examines the architecture, design, and test of continuous-time tunable intermediate-frequency (IF) fourth-order bandpass delta-sigma (BP ΔΣ) modulators. Bandpass modulators sampling at high IFs (~100 MHz) allow direct sampling of the RF signal-reducing analog hardware and make it easier to realize completely software programmable receivers. This paper presents circuit design of and test results from continuous-time fourth-order BP ΔΣ modulators fabricated in AlInAs/GaInAs heterojunction bipolar technology with a peak unity current gain cutoff frequency (f_T) of 80 GHz and a maximum frequency of oscillation (f_MAX) of about 130 GHz. Operating from ±5-V power supplies, a fabricated 180-MHz IF fourth-order ΔΣ modulator sampling at 4 GS/s demonstrates stable behavior and achieves 75.8 dB of signal-to-(noise+distortion)-ratio (SNDR) over a 1-MHz bandwidth. Narrowband performance (~1 MHz) performance of these modulators is limited by thermal/device noise while broadband performance (~60 MHz), is limited by quantization noise. The high sampling frequency (4 GS/s) in this converter is dictated by broadband (60 MHz) performance requirements     

A 3.2-GHz second-order delta-sigma modulator implemented in InP HBTtechnology

This paper presents a second-order delta-sigma (ΔΣ) modulator fabricated in a 70 GHz (f_T), 90 GHz (f_max) AlInAs-GaInAs heterojunction bipolar transistor (HBT) process on InP substrates. The modulator is a continuous time, fully differential circuit operated from ±5 volt supplies and dissipates 1 W. At a sample rate of 3.2 GHz and a signal bandwidth of 50 MHz (OSR=32100 MSPS Nyquist rate) the modulator demonstrates a Spur Free Dynamic Range (SFDR) of 71 dB (12-b dynamic range). The modulator achieves the ideal signal-to-noise ratio (SNR) of 55 dB for a second-order modulator at an oversampling ratio (OSR) of 32. The design of a digital decimation filter for this modulator is complete and the filter is currently in fabrication in the same technology. This work demonstrates the first ΔΣ modulator in III-V technology with ideal performance and provides the foundation for extending the use of ΔΣ modulator analog-to-digital converters (ADC's) to radio frequencies (RF)     

Triangularly weighted zero-crossing detector providingΣΔ frequency-to-digital conversion

It is shown that for delta-sigma (ΣΔ) frequency-to-digital conversion (FDC) there is no need for a ΣΔ modulator, since a limited FM signal itself may be considered as an asynchronous ΣΔ bit-stream. By feeding the limited FM signal directly to a sinc² ΣΔ decimator, a triangularly weighted zero-crossing counter FDC is introduced, providing ΣΔ noise shaping. The results measured confirm the theory     

CMOS oversampling ΔΣ magnetic-to-digital converters

In this paper, two CMOS oversampling delta-sigma (ΔΣ) magnetic-to-digital converters (MDCs) are proposed. The first MDC consists of the magnetic operational amplifier (MOP) and a first-order switched-capacitor (SC) ΔΣ modulator. The second one directly uses the MOP to realize a first-order SC ΔΣ modulator. They can convert the external magnetic field into digital form. Both circuits were fabricated in a 0.5-μm CMOS double-poly double-metal (DPDM) process and operated at a 5-V supply voltage and the nominal sampling rate of 2.5 MHz. The dynamic ranges of these converters are at least ±100 mT. The gain errors within ±100 mT are less than 3% and the minimum detectable magnetic field can reach as small as 1 mT. The resolutions are 100 μT for both of the two MDCs. The measured sensitivities are 1.327 mv/mT and 0.45 mv/mT for the first and the second MDC, respectively     

A 80-MHz bandpass ΔΣ modulator for a 100-MHz IFreceiver

A fully differential fourth-order bandpass ΔΣ modulator is presented. The circuit is targeted for a 100-MHz GSM/WCDMA-multimode IF-receiver and operates at a sampling frequency of 80 MHz. It combines frequency downconversion with analog-to-digital conversion by directly sampling an input signal from an intermediate frequency of 100 MHz to a digital intermediate frequency of 20 MHz. The modulator is based on a double-delay single-op amp switched-capacitor (SC) resonator structure which is well suited for low supply voltages. Furthermore, the center frequency of the topology is insensitive to different component nonidealities. The measured peak signal-to-noise ratio is 80 and 42 dB for 270 kHz (GSM) and 3.84-MHz (WCDMA) bandwidths, respectively. The circuit is implemented with a 0.35-μm CMOS technology and consumes 56 mW from a 3.0-V supply     

A switched-capacitor delta-sigma modulator with reduced sensitivityto op-amp gain

Low operational amplifier (op-amp) gain can degrade the performance of a switched-capacitor delta-sigma modulator (ΔΣM). A ΔΣM that incorporates a new gain-compensated switched-capacitor integrator is described. The resulting ΔΣM topology has reduced sensitivity to op-amp gain. Simulation and measurement results for an experimental ΔΣM that demonstrate the advantages of the new architecture are presented     

A two-path bandpass ΣΔ modulator for digital IFextraction at 20 MHz

Oversampled bandpass A/D converters based on sigma-delta (ΣΔ) modulation can be used to robustly digitize the types of narrowband intermediate frequency (IF) signals that arise in radios and cellular systems. This paper proposes a two-path architecture for a fourth-order, bandpass modulator that is more tolerant of analog circuit limitations at high sampling speeds than conventional implementations based on the use of switched-capacitor biquadratic filters. An experimental prototype employing the two-path topology has been integrated in a 0.6-μm, single-poly, triple-metal CMOS technology with capacitors synthesized from a stacked metal structure. Two interleaved paths clocked at 40 MHz digitize a 200-kHz bandwidth signal centered at 20 MHz with 75 dB of dynamic range while suppressing the undesired mirror image signal by 42 dB. At low input signal levels, the mixing of spurious tones at DC and f_s/2 with the input appears to degrade the performance of the modulator; out-of-band sinusoidal dither is shown to be an effective means of avoiding this degradation. The experimental modulator dissipates 72 mW from a 3.3 V supply     

Design and realization of a digital ΔΣ modulator forfractional-n frequency synthesis

The basic operation of a fractional-n frequency synthesizer has been published, but to date little has been presented on the digital ΔΣ modulators which are required to drive such synthesizers. This paper provides a tutorial overview, which relates digital ΔΣ modulation to other applications of ΔΣ modulation where the literature is more complete. The paper then presents a digital ΔΣ modulator architecture which is economical and efficient and which is practical to realize with commercially available components in comparison with other possible implementations which require extensive custom very large-scale integration (VLSI). A demonstration is made of a 28-b modulator using the architecture presented, which provides a 25-MHz tuning bandwidth and <1-Hz frequency resolution. The modulator is demonstrated in an 800-MHz frequency synthesizer having phase noise of -90 dBC/Hz at a 30-kHz offset     

A 14-bit current-mode ΣΔ DAC based upon rotated dataweighted averaging

A new dynamic element matching (DEM) algorithm, referred to as rotated data weighted averaging (RDWA), is implemented in a third-order ΣΔ digital-to-analog converter (DAC) with 64× oversampling and a conversion bandwidth of 25 kHz. The systematic and random errors are considered in the design of the 14-bit converter. The ΣΔ DAC is fabricated in a 2-μm CMOS process and includes the on-chip reconstruction filter. The prototype was designed to test the performance of the DAC without DEM, with data weighted averaging (DWA), and with RDWA. The results show that the new RDWA algorithm is capable of achieving first-order noise shaping while eliminating the signal-dependent harmonic distortion present in DWA