基于CCD成像的侧向散射激光雷达几何标定方法

通过分析CCD成像特点,设计了侧向散射激光雷达几何标定实验,得到CCD各像元的角宽度,并确定了CCD像元与散射光位置之间的对应关系.对两次实验中采集的回波信号进行标定,并分别与POM02进行相函数比对、与后向散射激光雷达进行探测信号比对,结果表明:相函数廓线和POM02测量结果相吻合;侧向散射激光雷达信号与后向散射雷达的距离修正信号在650m以上的变化趋势一致.侧向散射激光雷达弥补了后向散射激光雷达在近地面段不能探测气溶胶的不足,该标定方法可靠,为进一步利用侧向散射激光雷达研究近地面气溶胶的时空分布奠定了坚实的基础.     

基于侧向散射技术的近地面气溶胶后向散射系数廓线探测

气溶胶是大气中污染物PM2.5和灰霾的主要成分,近地面的气溶胶直接影响人们的生活和生产。利用电荷耦合器件(CCD)侧向散射激光雷达系统和相应的反演方法,对探测到的数据进行处理和分析。与后向散射激光雷达对比,验证了CCD侧向散射激光雷达探测结果的正确性。分析了2014年4月合肥西区董铺岛3 km高度范围内气溶胶后向散射系数的特点:随时间和高度变化;天气晴好时,地面上后向散射系数与地面站PM2.5质量浓度成正比;紧贴地面有一层较厚气溶胶。实验探测结果表明基于CCD的侧向散射激光雷达是探测近地面气溶胶浓度的一种有效的新方法。     

偏振-米散射激光雷达的研制

研制的偏振-米散射激光雷达（PML）,可用于探测卷云和沙尘气溶胶的后向散射光退偏振比以及研究流层大气气溶胶的消光特性。采用窄带滤光片和光阑,将接收到的激光大气回波信号谱线（米散射和瑞利散射光谱）从天空太阳背景噪声中分离出来,以提高系统的白天探测能力。介绍了偏振-米散射激光雷达的结构、技术参数、测量方法和数据处理方法。对偏振-米散射激光雷达的性能参数进行了测定,并对测定结果进行了分析与讨论,给出了偏振-米散射激光雷达对合肥市地区(117.16°E, 31.90°N)上空大气气溶胶的消光特性和卷云的结构、退偏振比垂直廓线以及光学厚度的典型探测结果,对这些结果进行了分析和讨论。结果表明：研制的偏振-米散射激光雷达性能可靠,能对大气气溶胶和卷云的物理和光学特性进行有效的探测。     

紫外激光雷达后向散射光强的模拟计算

根据瑞利散射和米散射理论建立了大气散射的模型,确定了米散射和瑞利散射的体角散射系数的计算公式,讨论了大气对激光任意方向的散射强度及散射光的偏振特性。对于波长为266nm的紫外光,通过仿真计算得到相应条件下的大气分子和气溶胶的后向散射系数及后向散射比,并对计算结果进行了分析。结果表明紫外波段具有散射强度大,抗干扰性强等优点,可以用于近距离的大气分子探测。通过对近距离探测大气的脉冲激光雷达的大气后向散射光强的仿真计算,合理的设置小孔光阑的参数,解决近端较强散射光的问题。这些仿真研究对紫外激光雷达系统的设计提供了指导。     

侧向散射激光雷达探测白天近地面气溶胶探测技术

基于CCD的侧向散射激光雷达不受几何因子的影响,是探测近地面气溶胶的有力工具。夜晚的探测技术已成熟,由于背景光中夜晚的月光和星光远弱于白天的太阳光,故利用夜晚探测技术得到的白天气溶胶信噪比很低。实验中选用窄带滤光片和小张角镜头,通过校正窄带滤光片透射率、缩短单次曝光时间、多次曝光平均等技术可有效提高白天探测气溶胶的信噪比。白天个例表明,侧向散射激光雷达与后向散射激光雷达反演的气溶胶后向散射系数廓线在0.75~1.50km范围内的变化趋势一致,并对0.75km以下侧向散射激光雷达探测的正确性进行了验证。对合肥地区近地面气溶胶后向散射系数进行了37h的连续昼夜探测,并与同一地点的温度、PM2.5质量浓度联合进行分析。研究表明,改进后的白天侧向散射激光雷达技术是正确、可行的。     

不同风速下侧向散射激光雷达的回波信号分析

对不同风速条件下,CCD侧向散射激光雷达的回波信号进行了分析.根据Mie散射原理及侧向散射激光雷达工作原理,确定了大气气溶胶浓度与激光雷达侧向散射光强的相关性;进一步考虑气溶胶浓度与风速的关联,利用实验装置获取了激光雷达侧向散射光强与风速的关系,分析了不同风速条件下侧向散射激光雷达的回波信号.在轴流风机以及自然风两种条件下进行对比实验发现,当风速范围在1~4.5 m/s时,侧向散射光强随风速的增加而增加;当风速范围在4.5~6.0 m/s时,光强随风速的增加较少.对实验结果归一化处理,得到风速范围在1~4.5 m/s时,风速每增加1 m/s,侧向散射光强在轴流风机及自然风的实验条件下分别增加了3.7%和3.9%;风速范围在4.5~6.0 m/s时,风速每增加1 m/s,侧向散射光强分别减少了3.1%和3.8%,在自然风况的各个风向上都基本符合这一变化趋势.     

基于回波信号仿真的瑞利-喇曼-米激光雷达研制

 在分析瑞利、喇曼和米散射仿真回波信号的基础上,研制了一台探测大气温度、气溶胶和卷云的瑞利-喇曼-米散射激光雷达,实现了一台激光雷达针对大气温度、气溶胶和卷云光学特性的多参数探测。为提高瑞利和喇曼微弱回波信号信噪比,采用了极高灵敏度的R4632光电倍增管和光子计数技术;为实现对大气气溶胶和卷云的探测,532 nm回波信号采取高低分层技术、高层通道回波衰减方法和探测器门控技术。瑞利-喇曼-米散射激光雷达的探测结果证明了利用仿真回波信号指导激光雷达设计的可行性。     

低层大气中确定气溶胶后向散射系数边界值的新方法

在反演大气气溶胶后向散射系数时,为了消除激光雷达系统常数,通常在对流层顶附近假设一个气溶胶后向散射系数的边界值。但当激光雷达的有效探测高度达不到对流层顶时,边界值的确定变得十分困难。从米氏散射激光雷达方程出发,得到了边界值与激光雷达距离平方校正回波信号之间的等式关系,并将该关系作为判据,利用迭代法在低层大气中找到一个比较准确的后向散射系数的边界值。将该方法应用于实际激光雷达回波信号反演中,得到低层大气中气溶胶后向散射系数廓线,并与在对流层顶选取边界值反演得到气溶胶后向散射系数廓线进行比较。结果表明,利用提出的方法在低层大气中确定的后向散射系数边界值,可以较好地反演出低层大气中气溶胶后向散射系数廓线。     

水汽探测拉曼激光雷达的新型光谱分光系统设计与分析

提出并设计了一套新型的大气水汽和气溶胶探测用紫外域拉曼激光雷达系统, 以二向色镜和超窄带滤光片构成高效率拉曼光谱分光系统, 实现激光雷达大气回波信号中米-瑞利散射信号、 氮气和水汽的振动拉曼散射信号的精细分离和高效率提取. 利用美国标准大气的分子散射模型和实测的大气米散射信号模型, 对分光系统的米-瑞利散射信号的抑制率、大气水汽测量的信噪比和误差进行数值仿真设计. 搭建实验系统对西安地区夜间的大气水汽进行实验观测, 并利用有云天气下实测的激光雷达回波信号, 反演获得大气后向散射比和水汽混合比的相关特性, 验证了该拉曼光谱分光系统对米-瑞利信号的抑制率达到10^-7以上量级. 理论和实验结果表明, 设计的新型拉曼光谱分光系统可以在大气后向散射比为17时, 实现水汽探测误差小于15%, 满足拉曼激光雷达系统对大气水汽的高效率探测. 关键词： 拉曼激光雷达 水汽混合比 大气后向散射比     

Rayleigh散射Doppler激光雷达风场反演方法改进

在Rayleigh散射Doppler激光雷达的风场反演过程中,除了温度、压强等因素之外,风速反演结果的 准确性还受到Mie散射信号的影响．当Mie散射信号较强时,尤其是遇到高层云或火山灰等情况,如果仍不考虑 气溶胶信号,由于温度不确定度和气溶胶信号的综合影响,风速反演结果将与真值偏差很大．本文提出了利用 激光雷达在垂直方向的测量信号同时反演后向散射比和大气温度的非线性迭代算法,并优化给出了最佳的 初始发射激光工作点．仿真试验结果表明:该方法可以准确有效地反演后向散射比;将该方法结合非线性迭代 风速反演方法,可以有效消除气溶胶后向散射信号的影响,进一步提高大气风速和温度的反演精度．     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.