小型化缝隙加载圆极化及宽带微带贴片天线设计

提出了一种十字形缝隙加载的小型宽带及圆极化微带贴片天线的设计方法。该天线通过在方形贴片上加载一个大尺寸的十字形缝隙实现天线的尺寸缩减,介质基片采用由FR4和空气层组成的层叠结构,在缝隙中嵌入L型枝节,只需通过调整枝节上同轴线馈电点的位置来获得圆极化或宽带阻抗匹配。ANSYS HFSS仿真分析表明,天线的圆极化带宽（AR≤3 dB）为1.7%,阻抗带宽（VSWR≤2）为5.8%,天线在宽带范围内具有稳定的增益,峰值增益为7.8 dB,同时贴片面积缩减了52.3%。改变馈电点的位置可调节两个谐振频率使天线阻抗带宽达到9.4%,比传统的微带贴片天线阻抗带宽提高了114%。     

应用于北斗和GPS的双频小型圆极化微带天线

介绍了一款能同时应用于北斗卫星导航系统B₃频段(1 268 MHz,±10 MHz)和全球卫星导航系统(GPS)L₁频段(1 575 MHz,±2 MHz)的双频小型圆极化微带天线,并通过叠层技术实现了天线的双频工作性能。采用相对介电常数为9.7的介质材料和表面开槽技术减小了天线尺寸,达到了小型化的要求。通过切角的方法实现了天线的右旋圆极化工作方式。同时,利用基于有限元法的HFSS仿真软件对天线进行了参数仿真和调试。仿真结果表明,在B₃频段天线具有2.2%的阻抗带宽(VSWR<2)和0.5%的3 dB轴比带宽,在L₁频段天线具有3.1%的阻抗带宽(VSWR<2)和0.5%的3 dB轴比带宽。天线仿真结果满足北斗和GPS指标要求,因此具有良好的应用前景。     

一种新型宽带双极化微带贴片天线的设计

摘要：运用口径耦合理论、腔模理论、反相馈电技术和多层贴片结构设计出一种新型的P波段（中心频率为0．75GHz）宽带双极化微带贴片天线。天线的两个极化端口采用共面馈电;馈电网络设计中采用短路耦合线实现反相馈电。仿真结果表明该天线两个极化端口实际增益均达到8．5dB,水平极化端口在0．64-0．85GHz频率范围内驻波比小于2,相对带宽为28％;垂直极化端口在0．68-0．85GHz频率范围内驻波比小于2,相对带宽为22．6％,两端口隔离度高于53dB。     

一种P波段宽带双极化微带天线阵列

介绍了一种P波段宽带双极化微带天线单元及2元阵列的设计。天线单元设计中采用口径耦合理论和多层贴片结构,增大了天线的带宽,两个极化端口采用共面馈电;馈电网络设计中采用反相馈电技术有效抑制了交叉极化,采用短路耦合线实现反相馈电,降低了对天线带宽的影响。仿真结果表明,该天线阵实际增益达到11.8dB,水平极化端口在0.68～0.86GHz频率范围内驻波比小于2,相对带宽为24%;垂直极化端口在0.63～0.86GHz频率范围内驻波比小于2,相对带宽为30.6%,两端口隔离度高于40dB。     

Broadband circularly polarised crosspatch- loaded square slot antenna

A new design of a circularly polarised square slot antenna loaded with a cross patch is presented. A cross patch inclined diagonally with respect to the square slot is placed at the centre of the square slot. By choosing proper dimensions of the cross patch, two orthogonal resonant modes with a 90deg phase difference for circular polarisation can be excited and feed the square slot antenna using a 50 Omega CPW with a protruded signal strip. 10 dB return loss bandwidth of 846 MHz (39.6%) and 3 dB axial ratio bandwidth of 240 MHz (12.4%) for the proposed antenna are achieved. Gain variation within the CP bandwidth is observed to be less than 1 dB     

一种超高频射频识别读写器天线

本文提出了一种适用于我国UHF RFID读写器的宽带圆极化叠层微带天线,通过选用廉价FR4板、空气层介质和对角线切角的正方形贴片组成叠层结构,采用S型水平蜿蜒带条激励主辐射贴片的馈电方式,展宽了天线的阻抗带宽和轴比带宽.所提出的S型水平蜿蜒带条馈电技术,实现了对称的辐射方向性图.给出了天线设计思路,并利用电磁仿真软件分...     

A VHF Microstrip Antenna With Wide-Bandwidth and Dual-Polarization for Sea Ice Thickness Measurement

A VHF microstrip patch antenna was developed to achieve a bandwidth of 45 MHz (30%) from 127 to 172 MHz with dual-linear-polarization capability. This microstrip antenna, having a size of 117 cm times 117 cm times 27 cm, used low-dielectric-constant foam substrates and dual-stacked patches with capacitive probe feeds to achieve the required wide bandwidth. Four such capacitive feeds were used to achieve dual polarizations with less than -20 dB of cross-polarization level. Twenty-four shorting pins were uniquely used here on the lower patch to achieve 40 dB of isolation between the two polarization ports. This antenna has a measured gain of 8.5 dB at 137 MHz and 10.3 dB at 162 MHz. One advantage observed here at the low frequencies of VHF is that more electrical structures can be easily integrated into the microstrip antenna to improve its performance.     

A quarter-wave U-shaped patch antenna with two unequal arms for wideband and dual-frequency operation

A wideband and dual-frequency quarter-wave U-shaped patch antenna with two unequal arms on FR4 substrate is presented. The U-shaped patch antenna is fed electromagnetically by another coaxially-fed patch on the same layer, which operates at a higher frequency band. In this paper, we first proposed a new technique to obtain two closely staggered resonant modes to achieve a wide impedance bandwidth using two unequal arms of the U-shaped patch for the lower band. For the substrate thickness = 5, 7.5 and 11 mm, the measured bandwidths of the antennas operating around at 900 MHz are 7%, 10%, and 18%, respectively. Then, we modify the coaxially-fed patch so that both bands are wide in bandwidth. The resulting antenna operating at 900 and 1800-MHz bands with the substrate thickness 11 mm has a measured impedance bandwidth of 13.3% and 20 respectively. This thickness corresponds to 0.033 free-space wavelength at 900 MHz. The far-field radiation patterns are stable in the two operating bands. The proposed antenna is simple in structure compared with the regular stacked or coplanar parasitic patch antennas. It is highly suitable for indoor mobile communications.     

非辐射边馈电的宽带双层微带贴片天线

介绍了一种非辐射边馈电的宽带双层微带贴片天线单元,并对其参数特性进行了仿真研究,结果表明,通过在寄生贴片上开3～5个与极化方向相平行的缝,可有效抑制天线的交叉极化,同时改善天线的阻抗带宽。相比传统双层微带贴片,该天线单元的阻抗带宽可提高3%以上,而交叉极化指标相当。当该单元应用于阵列天线设计时,可简化馈电网络,便于实现宽带、高效、大扫描角的微带共面馈电天线阵。对X波段8×8单元实验小阵的测试结果表明,该天线在17.6%的频段内具有良好的交叉极化性能及较高的工作效率。     

一种新型圆极化UHF通用型RFID读写器天线

面向超高频(UHF)通用型射频识别(RFID)读写器天线的应用需求,设计了一款完全覆盖全球UHF(840-960MHz)频段的RFID圆极化读写器天线。天线采用平面缝隙贴片结构,以共面波导(CPW)馈电方式实现宽频带圆极化特性。测试结果表明,天线的阻抗带宽为735-1014MHz(S11<-10dB),相对带宽31.9%,并且在840-960MHz频段内S11<-20dB,3dB轴比带宽为838-1134MHz,相对带宽30.0%,工作频带内有大于3.5dBi的平坦增益。仿真结果与测试结果基本吻合,天线结构精简,易于加工,满足全球UHF RFID读写器天线的应用需求。     

一种UHF频段小型圆极化微带天线

采用曲流技术在贴片内部开十字形缝隙,在贴片边缘开矩形缝隙,并通过对贴片切角形成微扰,设计了一种UHF频段小型圆极化微带天线。设计的贴片天线尺寸为59×59mm^2（即0．176λ）,与相同频率相同介质的普通微带贴片天线相比有约54％的尺寸下降。天线的实测结果显示,在898—925MHz内回波损耗小于-10dB,在910—920MHz实现圆极化特性。     

新型强耦合宽带双圆极化阵列天线

空间飞行器由于受到动力和负载的限制, 需要尽可能使搭载的天线轻质小型化.文中提出了一种新型强耦合双圆极化轻质天线.天线单元采用H型缝隙耦合和增加寄生贴片方法, 提高了天线带宽.同时, 通过在辐射贴片、寄生贴片上开圆形槽, 以及金属反射板栅格化的处理, 明显地减轻了天线的质量.采用这种新型天线单元, 设计了8单元的宽带双圆极化阵列天线.仿真结果表明:该阵列天线的中心频率为433 MHz, 左旋和右旋圆极化的相对轴比(Axial Ratio, AR)带宽(AR < 3 dB)分别达到了24.4%和23.2%, 有效实现了小型轻质化宽频带双圆极化阵列天线.     

Thin dual-resonant stacked shorted patch antenna for mobilecommunications

A novel thin stacked shorted patch antenna for the 1800 MHz frequency band is presented. The antenna is dual-resonant and small in size. It has a very low profile and a bandwidth of almost 10%, which is sufficient, for example, for GSM1800 or GSM1900 systems. The radiation pattern of the antenna is suitable for directive cellular handset antenna applications     

一种小型化宽频带天线单元的设计与研究

采用十字缝隙耦合、多层积叠贴片和双层馈电等技术,并选择双偏置微带线作为馈电,设计了一种小型化双极化宽频带微带缝隙天线。这些技术的采用拓宽了天线带宽,实现了良好的阻抗匹配。双层馈电技术减小了天线尺寸,并使天线的两个端口具有良好的隔离度。通过样品测量,驻波比小于1．5的端口相对带宽分别达40％和38．5％,工作频带内两端口隔离度（s21）大于25dB,增益最大值达9．1dB。该天线具有良好的性能并且工作于1710～2170MHz频段,可制作成天线阵应用于移动通信中。     

A New Coupling Mechanism for Circularly Polarized Annular-Ring Patch Antenna

A novel coupling technique for circularly polarized annular-ring patch antenna is developed and discussed. The circular polarization (CP) radiation of the annular-ring patch antenna is achieved by a simple microstrip feed line through the coupling of a fan-shaped patch on the same plane of the antenna. Proper positioning of the coupling fan-shaped patch excites two orthogonal resonant modes with 90 phase difference, and a pure circular polarization is obtained. The dielectric material is a cylindrical block of ceramic with a permittivity of 25 and that reduces the size of the antenna. The prototype has been designed and fabricated and found to have an impedance bandwidth of 2.3% and a 3 dB axial-ratio bandwidth of about 0.6% at the center frequency of 2700 MHz. The characteristics of the proposed antenna have been by simulation software HFSS and experiment. The measured and simulated results are in good agreement.     

一种寄生阵列宽带圆极化天线的设计

该文设计了一款C波段单馈寄生阵列的宽带圆极化天线。此天线采用紧邻的双层F4B介质基板,通过在方形驱动贴片上开槽及采用寄生阵列的设计实现了圆极化。对天线结构的设计步骤进行说明,研究了各结构对天线阻抗带宽和轴比带宽的影响,并研究了寄生贴片切角长度和驱动贴片上的缝隙宽度对天线轴比和带宽的影响。对天线的圆极化方向图进行了仿真。仿真结果表明,在5.5 GHz时实现了右旋圆极化,最大增益为8.1 dBi。加工并测试了宽带圆极化天线,测试结果与仿真结果基本相符,天线实测的阻抗带宽为1.3 GHz,轴比带宽为1.26 GHz。设计的叠层天线具有结构紧凑,装配简单和轴比带宽大的优点。     

Novel design of broad-band stacked patch antenna

A novel broadband stacked E-shaped patch antenna is proposed in this paper. The proposed antenna has an input impedance bandwidth of about 38.41%, better than the conventional E-shaped microstrip patch antenna, which has an input impedance bandwidth of 33.8%. Through the use of the washer on the probe of the stacked patch antenna, the input impedance bandwidth is improved further to 44.9%. The radiation patterns are found to be relatively constant throughout the whole band. Comparisons of these antennas are presented in this paper.     

一种小型化北斗导航终端圆极化天线的设计

设计了一款单馈电的小型圆极化微带天线。在方形贴片上,通过切角和对称开槽的方法,天线获得了良好的右旋圆极化性能,并实现了小型化设计。借助HFSS电磁仿真软件,对天线参数进行了仿真和分析。仿真结果表明,S11＜-10 dB的阻抗带宽为82 MHz,3 dB圆极化轴比带宽为12 MHz,较好地满足了北斗接收天线的设计要求。该设计具有方法简单、易于实现、成本较低等优点,且具有良好的应用前景。     

Shorting strap tunable stacked patch PIFA

An oppositely shorted dual-band stacked patch planar inverted-F antenna (PIFA) is developed. RF switches are integrated to the shorting straps of the stacked patches to make a tunable PIFA. The L band switch yields 0.45-dB insertion loss and 10-dB isolation bandwidth (BW) of 108% at 1.8 GHz. The tunable PIFA yields 10% frequency tunability BW at 745 MHz when the number of upper radiating patch's shorting straps changes and 20% BW at 1137 MHz when the number of lower radiating patch's shorting straps changes. Independent lower and upper frequency tunings are achieved through this technique.     

A Circularly Polarized Stacked Patch Aperture Coupled Microstrip Antenna for 2.6 GHz Band

A circularly polarized stacked patch microstrip antenna and a 2?×?2 subarray for circular polarization are proposed in this paper. The proposed design has the input impedance bandwidth and axial ratio bandwidth of about 10% and 4.7% respectively. Circular polarization is obtained with the help of slits cut in the patch. A size reduction of around 37% is also achieved with the help of the slits. A subarray based on sequentially rotated feeding technique for circular polarization is also presented in this paper. Array element was deigned using a high dielectric constant laminate for feed network. In addition to low boresight axial-ratio, the subarray has impedance and 3-dB axial-ratio bandwidths of 12% and 8% respectively.