Preparation of polypropylene‐based nanocomposites using nanosized MCM‐41 as support and in situ polymerization

MCM‐41 nanoparticles were used for preparing nanocomposites through the in situ polymerization of propylene. The performance of the catalytic system and the final properties of the materials obtained are highly dependent on the methodology used for impregnation of the catalyst onto the support particles, and therefore an optimization study for the impregnation methodology of the catalyst (Me₂Si(Ind)₂ZrCl₂) was carried out. Two different methodologies were used; the results in terms of catalytic activity and polymer molecular masses indicated that the most promising one involved the pre‐activation of the catalyst with the cocatalyst, methylaluminoxane, followed by impregnation onto the MCM‐41 nanoparticles. Thus, an optimized route for the preparation of polypropylene nanocomposites achieving significant improvements in catalyst activity was developed. The nanocomposite materials were characterized by GPC, TGA and DSC. The dispersion state and the size of the nanoparticles incorporated in the polypropylene matrix were investigated by transmission electron microcopy. Additionally, this methodology allows simultaneous control of the desired amount of support and the concentration of catalyst to be used in the in situ polymerization. © 2015 Society of Chemical Industry     

An activated neodymium‐based catalyst for styrene polymerization

Coordination polymerization of styrene with a ternary catalyst system composed of catalyst neodymium tricarboxylate (Nd), co‐catalyst Al(i‐Bu)₃ (Al) and chlorinating agent trichloroethane (Cl) was carried out in cyclohexane. The effects of the catalyst system preparation procedure and of the reaction conditions on catalytic activity, molecular weight and molecular weight distribution of the resultant polymers were investigated. The catalytic activity depended mainly on the molar ratios of Al/Nd and of Cl/Nd and on the ageing temperature and polymerization temperature. High polymerization conversion and high catalytic activity could be obtained at high Al/Nd ratios and/or at high ageing temperature. The catalyst system exhibited high activity of 8.32 × 10⁴ g polystyrene (mol Nd h)^?1 at 50 °C. The molecular weight of the polymers obtained reached high weight‐average (M_w) values (M_w = 4.35 × 10⁵ g mol^?1) when Al/Nd = 8, but relatively low values (6000–11 000 g mol^?1) at high Al/Nd ratios. Copyright © 2005 Society of Chemical Industry     

The synthesis of high molecular weight polybutene‐1 catalyzed by Cp★ Ti(OBz)3/MAO

A new stereoregular polybutene‐1 was synthesized with a novel catalyst precursor η⁵‐pentamethyl cyclopentadienyl titanium tribenzyloxide (CpTi(OBz)₃) and methylaluminoxane (MAO). The effects of polymerization conditions on the catalytic activity, molecular weight and stereoregularity of the products were investigated in detail. It was found the catalyst exhibited highest activity of 91.2 kgPB mol Ti⁻¹ h⁻¹ at T = 30 °C, Al/Ti = 200. The catalytic activity and molecular weight were sensitive to the Al/Ti (mole/mole), polymerization temperature; they also depended on the Ti concentration. The molecular weight of the products increased with decreasing temperature. The structure and properties of the polybutene‐1 were characterized by ¹³C NMR, GPC, DSC and WAXD. The result showed the microstructure of polybutene‐1 extracted by boiling heptane was stereoregular, whereas the ether‐soluble fraction was atactic. The molecular weight of polybutene‐1 was over one million g mol⁻¹ and its molecular weight distribution ( M _w/ M _n) was from 1.1 to 1.2. © 2001 Society of Chemical Industry     

Organic/inorganic support for immobilizing (n‐BuCp)2ZrCl2/TiCl3 hybrid catalyst for use in the preparation of polymer blends

Reactor blends of ultrahigh‐molecular‐weight polyethylene (UHMWPE) and low‐molecular‐weight polyethylene (LMWPE) were synthesized by two‐step polymerization using a hybrid catalyst. To prepare the hybrid catalyst, styrene acrylic copolymer (PSA) was first coated onto SiO₂/MgCl₂‐supported TiCl₃; then, (n‐BuCp)₂ZrCl₂ was immobilized onto the exterior PSA. UHMWPE was produced in the first polymerization stage with the presence of 1‐hexene and modified methylaluminoxane (MMAO), and the LMWPE was prepared with the presence of hydrogen and triethylaluminium in the second polymerization stage. The activity of the hybrid catalyst was considerable (6.5 × 10⁶ g PE (mol Zr)^?1 h^?1), and was maintained for longer than 8 h during the two‐step polymerization. The barrier property of PSA to the co‐catalyst was verified using ethylene polymerization experiments. The appearance of a lag phase in the kinetic curve during the first‐stage polymerization implied that the exterior catalyst ((n‐BuCp)₂ZrCl₂) could be activated prior to the interior catalyst (M‐1). Furthermore, the melting temperature, crystallinity, degree of branching, molecular weight and molecular‐weight distribution of polyethylene obtained at various polymerization times showed that the M‐1 catalyst began to be activated by MMAO after 40 min of the reaction. The activation of M‐1 catalyst led to a decrease in the molecular weight of UHMWPE. Finally, the thermal behaviors of polyethylene blends were investigated using differential scanning calorimetry. Copyright © 2011 Society of Chemical Industry     

Synthesis of ultra‐high molecular weight polystyrene with rare earth–magnesium alkyl catalyst system: general features of bulk polymerization

Bulk polymerization of styrene (St) with an in‐situ‐activated Ziegler‐catalyst containing neodymium 2‐ethylhexyl phosphonate [Nd(P₂₀₄)₃], magnesium–aluminum alkyls and hexamethyl phosphoramide (HMPA) was studied. The new rare‐earth catalyst exhibited high activity for polymerization of styrene, and its catalytic efficiency reached 14 730 g PSt/g Nd. The influence of reaction parameters, such as Mg/Nd, Mg/Al, St/Nd molar ratios, temperature, etc, on the catalyst performance was examined in detail. The molecular weight of the resulting polystyrene is ultra‐high (M_W = 40 × 10⁴ ∼ 120 × 10⁴ g mol⁻¹) and the distribution of molecular weight is broad (M_W/M_n = 2.1 ∼ 2.8). The microstructure of the polystyrene was characterized by IR and ¹³C NMR spectroscopies and found to be atactic. © 2001 Society of Chemical Industry     

Ring‐opening metathesis polymerization of norbornene catalyzed by tantalum and niobium complexes with chelating O‐donor ligands

BACKGROUND: In comparison with group 6 transition metals, such as tungsten and molybdenum, and group 8 metal ruthenium, group 5 metal‐based catalysts for ring‐opening metathesis polymerization (ROMP) have remained much less studied. The few reported ROMP catalysts of group 5 metals require multiple reaction steps to be synthesized, and are highly sensitive to air and moisture. RESULTS: A series of pentavalent tantalum and niobium complexes having catecholato, tropolonato, hinokitiolato, biphenolato and binaphtholato ligands were prepared and their catalytic activities for the ROMP of norbornene (NBE) were studied in the presence of trialkylaluminium as a co‐catalyst. Among these complexes, the tantalum complexes showed high activity upon activation with Buⁱ₃Al. In sharp contrast, the niobium complexes were effectively activated with Me₃Al. The polymers obtained with these complexes had high molecular weights (M_n > 10⁵ g mol⁻¹) and relatively narrow molecular weight distributions (M_w/M_n ≈ 2). CONCLUSION: We found that easily accessible and relatively stable tantalum and niobium complexes with such chelating O‐donor ligands showed high catalytic activity for ROMP of NBE depending on the kind of co‐catalyst. These findings could contribute to future development of ROMP catalysts. Copyright © 2008 Society of Chemical Industry     

The investigation of novel non‐metallocene catalysts with phenoxy‐imine ligands for ethylene (co‐)polymerization

Phthaldialdehyde and phthaldiketone were treated with substituted phenols of 2‐amino‐4‐methylphenol, 2‐amino‐5‐methylphenol and 2‐amino‐4‐t‐butylphenol, respectively, and then treated with transition metal halides of TiCl₄, ZrCl₄ and YCl₃. A series of novel non‐metallocene catalysts (1–12) with phenoxy‐imine ligands was obtained. The structures and properties of the catalysts were characterized by ¹H NMR and elemental analysis. The catalysts (1–12) were used to promote ethylene (co‐)polymerization after activation by methylaluminoxane. The effects of the structures and center atoms (Ti, Zr and Y) of these catalysts, polymerization temperature, Al/M (M = Ti, Zr and Y) molar ratio, concentration of the catalysts and solvents on the polymerization performance were investigated. The results showed that the catalysts were favorable for ethylene homopolymerization and copolymerization of ethylene with 1‐hexene. Catalyst 10 is most favorable for catalyzing ethylene homopolymerization and copolymerization of ethylene with 1‐hexene, with catalytic activity up to 2.93 × 10⁶ gPE (mol Y)^?1 h^?1 for polyethylene (PE) and 2.96 × 10⁶ gPE (mol Y)^?1 h^?1 for copolymerization of ethylene with 1‐hexene under the following conditions: polymerization temperature 50 °C, Al/Y molar ratio 300, concentration of catalyst 1.0 × 10^?4 L^?1 and toluene as solvent. The structures and properties of the polymers obtained were characterized by Fourier transform infrared spectroscopy, ¹³C NMR, wide‐angle X‐ray diffraction, gel permeation chromatography and DSC. The results indicated that the obtained PE catalyzed by 4 had the highest melting point of 134.8 °C and the highest weight‐average molecular weight of 7.48 × 10⁵ g mol^?1. The copolymer catalyzed by 4 had the highest incorporation of 1‐hexene, up to 5.26 mol%, into the copolymer chain. © 2012 Society of Chemical Industry     

Copolymerization of ethylene–propylene using high‐activity bi‐supported Ziegler–Natta TiCl4 catalyst

Heterogeneous Ziegler–Natta TiCl₄ catalyst using MgCl₂ and SiO₂ as supports was prepared under controlled conditions. Mg(OEt)₂ was used as a starting material and was expected to convert to active MgCl₂ during catalyst preparation. Due to the high surface area and good morphological control, SiO₂ was chosen as well. Slurry copolymerization of ethylene and propylene (EPM) was carried out in dry n‐heptane by using the catalyst system SiO₂/MgCl₂/TiCl₄/EB/TiBA or TEA/MPT/H₂ at temperatures of 40–70°C, different molar ratios of alkyl aluminum : MPT : Ti, hydrogen concentrations, and relative and total monomers pressure. Titanium content of the catalyst was 2.96% and surface area of the catalyst was 78 m²/g. Triisobutyl aluminum (TiBA) and triethyl aluminum (TEA) were used as cocatalysts, while ethyl benzoate (EB) and methyl p‐toluate (MPT) were used as internal and external donors, respectively. H₂ was used as a chain‐transfer agent. Good‐quality ethylene propylene rubber (EPR) of rubber was obtained at the ratio of [TiBA] : [MPT] : [Ti] = 320 : 16 : 1 and polymerization temperature was 60°C. When TiBA was used as a cocatalyst, a higher and more rubberlike copolymer was obtained. For both of the cocatalysts, an optimum ratio of Al/Ti was obtained relative to the catalyst productivity. Ethylene content of the copolymer obtained increased with increasing TiBA concentration, while inverse results were obtained by using TEA. Addition of H₂ increased the reactivity of the catalyst. The highest product was obtained when 150 mL H₂/L solvent was used. Increasing temperature from 40 to 70°C decreased the productivity of the catalyst, while irregular behavior was observed on ethylene content. Relative pressure of P_P/P_E = 1.4 : 1 and total pressure of 1 atm was the best condition for the copolymerization. Polymers with ethylene contents of 25–84% were obtained. Increasing ethylene content of EPR decreased T_g of the polymer obtained to a limiting value. Viscosity‐average molecular weight (M_v) decreased with increasing temperature and TiBA and H₂ concentration. However, increasing the polymerization time increased the M_v. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2597–2605, 2004     

Ethylene/1‐octadecene copolymerization using [η5:η1‐C5Me4‐4‐R1‐6‐R‐C6H2O]TiCl2 catalysts

Copolymerization of ethylene with 1‐octadecene was studied using [η⁵:η¹‐C₅Me₄‐4‐R₁‐6‐R‐C₆H₂O]TiCl₂ [R₁ = ^tBu (1), H (2, 3, 4); R = ^tBu (1, 2), Me (3), Ph (4)] as catalysts in the presence of Al(i‐Bu)₃ and [Ph₃C][B(C₆F₅)₄]. The effect of the concentration of comonomer in the feed and Al/Ti molar ratio on the catalytic activity and molecular weight of the resultant copolymer were investigated. The substituents on the phenyl ring of the ligand affect considerably both the catalytic activity and comonomer incorporation. The 1 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system exhibits the highest catalytic activity and produces copolymers with the highest molecular weight, while the 2 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system gives copolymers with the highest comonomer incorporation under similar conditions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

A new post‐metallocene catalyst for alkene polymerization: copolymerization of ethylene and 1‐hexene with titanium complexes bearing N,N‐dialkylcarbamato ligands

A new type of post‐metallocene polymerization catalyst based on titanium complexes with N,N‐dialkylcarbamato ligands was used to copolymerize ethylene and 1‐hexene. These easy‐to‐synthesize and stable complexes in combination with different organoaluminium co‐catalysts produce random ethylene/1‐hexene copolymers characterized by a broad molecular weight distribution and high 1‐hexene incorporation, as confirmed by SEC, DSC and ¹³C NMR analysis. The influence of the main reaction parameters on the polymerization reactions was studied including the type of catalyst components, solvent, temperature, the ethylene partial pressure and the [Al]/[Ti] ratio in the catalyst. A higher activity and a higher 1‐hexene incorporation were achieved with AlMe₃‐depleted methylalumoxane as co‐catalyst and chlorobenzene as solvent. © 2013 Society of Chemical Industry     

Polymerization of styrene using bis(β‐ketoamino)nickel(II)/methylaluminoxane catalytic systems

Styrene (St) was polymerized in toluene solution by using bis(β‐ketoamino)nickel(II) complex as the catalyst precursor and methylaluminoxane (MAO) as the cocatalyst. The polymerization conditions, such as Al : Ni ratio, monomer concentration, reaction temperature, and polymerization time, were studied in detail. Both of the bis(β‐ketoamino)nickel(II)/MAO catalytic systems exhibited higher activity for polymerization of styrene, and polymerization gave moderate molecular weight of polystyrene with relatively narrow molecular weight distribution (M_w/M_n < 1.6). The obtained polymer was confirmed to be atactic polystyrene by analyzing the stereo‐triad distributions mm, mr, and rr of aromatic carbon C¹ in NMR spectrum of the polymer. The mechanism of the polymerization was also discussed and a metal–carbon coordination mechanism was proposed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation of high isotactic polybutene‐1

Polymerization of butene‐1 (B‐1) was carried out with a PP‐TiCl₃/Et₂AlCl/methyl methacrylate (MMA) catalyst system in n‐heptane. The influence of temperature, pressure, time and H₂ on molecular weight, isotacticity, and catalytic activity were studied by viscometry, solubility in boiling diethyl ether, and measuring the polymer produced, respectively. The structural properties of the isotactic polybutene‐1 (IPB‐1) were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and melt flow index (MFI). The molecular weight of the products can be controlled by H₂. It was found that the catalyst showed high isotacticity and activity. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2533–2539, 2000     

Preparation of isotacticity‐rich poly(tert‐butyl vinyl ether) by the cationic polymerization of tert‐butyl vinyl ether with dimethyl[rac‐ethylenebis(indenyl)]zirconium and tri(pentafluorophenyl)borane

tert‐Butyl vinyl ether (tBVE) was polymerized with the catalyst dimethyl[rac‐ethylenebis(indenyl)] zirconium (ansa‐zirconocene) with tri(pentafluorophenyl) borane [B(C₆F₅)₃] as a cocatalyst. The effects of various polymerization conditions, such as the polymerization time, type of polymerization solvent, polymerization temperature, and catalyst concentration, on the conversion of tBVE into poly(tBVE), its molecular weight and molecular weight distribution, and its stereoregularity were investigated. The maximum conversion of tBVE into poly(tBVE) was over 90% at a polymerization temperature of ?30°C with an ansa‐zirconocene and B(C₆F₅)₃ concentration of 3.0 × 10^?7 mol/mol of tBVE, respectively. The number‐average molecular weights of poly(tBVE) ranged from approximately 14,000 to 20,000, with a lower polydispersity index (weight‐average molecular weight/number‐average molecular weight) ranging from 1.48 to 1.77, at all polymerization temperatures. The number‐average molecular weight of poly(tBVE) increased with decreases in the polymerization temperature and catalyst concentration. The mm triad sequence fraction of poly(tBVE) polymerized with ansa‐zirconocene/B(C₆F₅)₃ at ?30°C was much higher than that of poly(tBVE) polymerized with the B(C₆F₅)₃ catalyst at ?30°C, and this indicated that the ansa‐zirconocene/B(C₆F₅)₃ catalyst system affected the isospecific polymerization of tBVE. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polymerization of acrylonitrile catalyzed by single yttrium tris(2,6‐di‐tert‐butyl‐4‐methyl phenolate)

Polymerization of acrylonitrile was carried out using yttrium tris(2,6‐di‐tert‐butyl 4‐methyl‐phenolate) (Y(OAr)₃) as single component catalyst for the first time. The effects of concentrations of the monomer and catalyst, kinds of rare earth element and solvent, as well as temperature and polymerization time were investigated. The overall activation energy of polymerization in n‐hexane and THF mixture is 18.3 kJ mol^?1. Polyacrylonitriles (PANs) obtained by using Y(OAr)₃ in n‐hexane and THF mixture at 50 °C are predominantly atactic, while yellow PANs obtained in DMF under the same conditions have a syndiotactic‐rich configuration (>50%), and their highly branched and/or cyclized structures have also been found. © 2002 Society of Chemical Industry     

Gas phase polymerization of 1,3‐butadiene with supported neodymium‐based catalyst: Investigation of molecular weight

The gas phase polymerization of 1,3‐butadiene (Bd), with supported catalyst Nd(naph)₃/Al₂Et₃Cl₃/Al(i‐Bu)₃ or/and Al(i‐Bu)₂H, was investigated. The polymerization of Bd with neodymium‐based catalysts yielded cis‐1,4 (97.2–98.9%) polybutadiene with controllable molecular weight (MW varying from 40 to 80 × 10⁴ g mol^?1). The effects of reaction temperature, reaction time, Nd(naph)₃/Al(i‐Bu)₃ molar ratio, and cocatalyst component on the catalytic activity and molecular weight of polymers were examined. It was found that there are two kinds of active sites in the catalyst system, which mainly influenced the MW and molecular weight distribution of polybutadiene. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1945–1949, 2004     

Ring‐opening metathesis polymerization of bicyclo[2.2.1]hepta‐2,5‐diene (norbornadiene) initiated by new ruthenium(II) complex

The polymerization of norbornadiene (NBD) initiated by a novel ruthenium (Ru)(II) complex ( 3 ) containing 1,1′‐pyridine‐2,6‐diylbis[3‐(dimethylamino)prop‐2‐en‐1‐one] ( 1 ) as ligand has been investigated. Ru complexes exhibit more catalytic activity in the ring‐opening metathesis polymerization (ROMP) of NBD when activated with trimethylsilyldiazomethane (TMSD). The influence of the various experimental parameters such as reaction time and temperature, nature of the solvent and catalyst, ratio of the NBD/Ru, and TMSD addition has been investigated. The polymers have been obtained in high yields with a relatively low polydispersity index for ROMP and a high $ \bar M_n $ and $ \bar M_w $ values in a monomodal distribution. Their structures have been determined by means of FTIR and ¹H‐NMR spectroscopy. Thermal properties have been determined via thermogravimetric analysis and DTG methods. The NBD polymerization results that initiated by Ru‐based catalyst coordinated to amine ligand have been compared to initiated by [RuCl₂(p‐cymene)]₂. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Iron‐based electrochemically mediated atom transfer radical polymerization with tunable catalytic activity

An iron‐based electrochemically mediated atom transfer radical polymerization (eATRP) system with tunable catalytic activity was developed by adjusting the supporting electrolyte formula. Kinetic behaviors of the systems using four typical supporting electrolytes (namely, TBABr, TBAPF₆, TBACl, and TBABF₄) were investigated. The type of anions was found to significantly affect the polymerization kinetics. TBAPF₆ system proceeded with a considerable polymerization rate, whereas TBABr system showed better controllability. Importantly, the effect of supporting electrolyte on eATRP kinetics (mainly on ATRP equilibrium) was confirmed through kinetic modeling. Furthermore, the effect of catalyst loading using TBAPF₆ as supporting electrolyte was also studied, and the results showed an uncontrolled polymerization for catalyst loading lower than 500 ppm. When hybrid supporting electrolyte (TBAPF₆/TBABr) was used to tune catalytic activity, the polymerization slows down and the dispersity decreases with the increase in TBABr ratio. Polymers with a narrow molecular weight distribution (dispersity index <1.5) were obtained using 100% TBABr under 100 ppm catalyst. Besides, experimental attempt to improve the controllability by adding halogen donors was made, whereas the halogen donors just prolonged the induction period and no improvement was achieved. As a whole, a deeper understanding of kinetic studies is obtained by these controlled trials. © 2017 American Institute of Chemical Engineers AIChE J, 64: 961–969, 2018     

Liquid Pool Copolymerization of Propylene/1‐Butene with a MgCl2‐Supported Ziegler‐Natta Catalyst

Summary: Liquid pool propylene/1‐butene copolymerizations were carried out in a batch reactor with a high activity Ziegler‐Natta catalyst system. Experimental runs were performed to evaluate the effect of the 1‐butene content on the crystallinity and melt temperature of the polymer resins. According to the results, 1‐butene can be significantly incorporated into the polymer chain at high polymerization rates over the whole range of copolymer compositions, leading to a decrease in the melting temperature (T_m) of the polymer, when compared to the poly(propylene) homopolymer, allowing for reduction of the sealing initiation temperature. It was observed by GPC and MFI measurements that the average molecular weights and the polydispersity index of the copolymer significantly decreased when compared to the ones obtained from poly(propylene). Despite high polymerization rates, polymer particles with good morphological features were produced in all cases. It was also observed that the absence of an external electron donor led to low crystallinity values for both the poly(propylene) homopolymer and for copolymers with different fractions of 1‐butene, when compared to literature values frequently reported for polymer resins based on 1‐butene and propylene. The obtained results indicate that a family of bulk propylene/1‐butene copolymer grades can be successfully developed for packaging and film applications.

Surface morphology and molecular weight distribution (deconvoluted into Schulz‐Flory distributions) of the propylene/1‐butene copolymer.     

Hybrid titanium catalyst supported on core‐shell silica/poly(styrene‐co‐acrylic acid) carrier

Hybrid titanium catalysts supported on silica/poly(styrene‐co‐acrylic acid) (SiO₂/PSA) core‐shell carrier were prepared and studied. The resulting catalysts were characterized by Fourier transform infrared (FTIR) spectroscopy, laser scattering particle analyzer and scanning electronic microscope (SEM). The hybrid catalyst (TiCl₃/MgCl₂/THF/SiO₂·TiCl₄/MgCl₂/PSA) showed core‐shell structure and the thickness of the PSA layer in the two different hybrid catalysts was 2.0 μm and 5.0 μm, respectively. The activities of the hybrid catalysts were comparable to the conventional titanium‐based Ziegler‐Natta catalyst (TiCl₃/MgCl₂/THF/SiO₂). The hybrid catalysts showed lower initial polymerization rate and longer polymerization life time compared with TiCl₃/MgCl₂/THF/SiO₂. The activities of the hybrid catalysts were enhanced firstly and then decreased with increasing P/P. Higher molecular weight and broader molecular weight distribution (MWD) of polyethylene produced by the core‐shell hybrid catalysts were obtained. Particularly, the hybrid catalyst with a PSA layer of 5.0 μm obtained the longest polymerization life time with the highest activity (2071 kg PE mol^?1 Ti h^?1) and the resulting polyethylene had the broadest MWD (polydispersity index = 11.5) under our experimental conditions. The morphology of the polyethylene particles produced by the hybrid catalysts was spherical, but with irregular subparticles due to the influence of PSA layer. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Microwave‐irradiated ring‐opening polymerization of D,L‐lactide under atmosphere

Poly(D ,L ‐lactide) (PDLLA) was synthesized by microwave‐irradiated ring‐opening polymerization catalyzed by stannous octoate (Sn(Oct)₂) under atmosphere. The effects of heating medium, monomer purity, catalyst concentration, microwave irradiation time, and vacuum level were discussed. Under the appropriate conditions such as carborundum (SiC) as heating‐medium, 0.15% catalyst, lactide with purity above 99.9%, 450 W microwave power, 30 min irradiation time, and atmosphere, PDLLA with a viscosity–average molecular weight (M_η) over 2.0 × 10⁵ and a yield over 85% was obtained. The dismission of vacuum to ring‐opening polymerization of D ,L ‐lactide (DLLA) under microwave irradiation simplified the process greatly. The temperature under microwave irradiation and conventional heating was compared. The largely enhanced ring‐opening polymerization rate of DLLA under microwave irradiation was the coeffect of thermal effects and microwave effects. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2244–2247, 2006