Effect of the Pretreatment with UV and Gamma Radiations on the Modification of Plywood Surface by Photocuring with Epoxy Acrylate

In order to further improve the physical properties of plywood surface that was pretreated with UV and Gamma radiation at different radiation intensities before photocuring. After pretreatment with radiation the plywood surface was coated with different prepared formulations containing epoxyacrylate (EA-1020) as an oligomer, difunctional monomers such as tripropylene glycol diacrylate (TPGDA), 2-hexadioldiacrylate (HDDA), Ethylene Glycol dimethacrylate (EGDMA) and trifunctional monomer trimethyl propen triacrylate (TMPTA) with photoinitiator Darocur 1664. Thin polymer films were prepared on glass plate with these formulated solutions and cured under UV radiation. Pendulum hardness (PH) and gel content of the film were studied for selecting the formulations as top coat and as base coat. The polished plywood surface was coated with selected formulation and cured under UV radiation. Various rheological properties of UV cured plywood surface such as pendulum hardness, scratch hardness, microgloss, adhesion strength, percentage chipped off area and abrasion resistance were studied.     

Effect of Pretreatment with UV Radiation on Physical and Mechanical Properties of Photocured Jute Yarn with 1,6-Hexanediol Diacrylate (HDDA)

Jute yarns were grafted with a single impregnating monomer 1,6-hexanediol diacrylate (HDDA) in order to improve the physicomechanical properties. Jute yarns soaked for different soaking times (3, 5, 10, and 30 minutes) in HDDA+MeOH solutions at different proportions (1–10% HDDA in MeOH [v/v] along with photoinitiator Darocur-1664 [3%]) were cured under UV lamp at different UV radiation intensities (two, four, six, and eight passes). Concentration of monomer, soaking time, and intensity of UV radiation were optimized with extent of mechanical properties such as tensile strength, elongation at break, and modulus. Enhanced tensile strength (67%), modulus (108%), and polymer loading (11%) were achieved with 5% HDDA concentration, 5-minute soaking time, fourth pass of UV radiation. To further improve the mechanical properties, the jute yarns were pretreated with UV radiation (5, 10, 15, 30, and 50 passes) and treated with optimized monomer concentration (5%). UV-pretreated samples showed the enhanced properties. The tensile strength and modulus increase up to 84% and 132%, respectively, than that of virgin jute yarn. An experiment involving water absorption capacity shows that water uptake by treated samples was much lower than that of the untreated samples. During the weathering test, treated yarns exhibited less loss of mechanical properties than untreated yarns.     

Study on the Physico-mechanical Properties of Photo-cured Chitosan Films with Oligomer and Acrylate Monomer

Chitosan films were prepared from dried prawn shell via chitin and then tensile properties like tensile strength (TS) and elongation at break (Eb) of the films were evaluated. Six formulations were developed using methyl methacylate (MMA) monomer and aliphatic urethane diacrylate oligomer (M-1200) in methanol along with photoinitator (Darocur-1664). Then the films were soaked in the formulations and irradiated under UV radiation at different doses for the improvement of physico-mechanical properties of chitosan films. The cured films were characterized by measuring TS, Eb, polymer loading (PL), water absorption and gel content properties. The formulation containing 43% MMA and 15% oligomer in methanol solution showed the best performance at 20th UV pass for 4 min soaking time.     

Effect of Urea on the Mechanical Properties of Gelatin Films Photocured with 2-Ethylhexyl Acrylate

Thin films of gelatin were prepared by casting. Then the films were photocured and the mechanical properties were studied. The tensile strength of UV cured gelatin films showed about 10% enhancement than that of raw gelatin films. Minor amount of urea (1–5%) was used as additive in aqueous gelatin solution and films were prepared using same technique. Four formulations were prepared in methanol with 2-ethylhexyl acrylate in the presence of photoinitiator (darocur-1664). The films were soaked in the prepared formulations and then cured under UV radiation at different intensities (5–25 passes). Percentage of urea, monomer concentration, soaking time and radiation intensities were optimized with the extent of polymer loading, TS and elongation at break of the photocured film. The films containing 2% urea, cured with 3% EHA for 3 min at 15th UV pass showed the highest mechanical properties. A significant improvement of TS (31%) occurred when EHA (3%) was incorporated.     

Soybean Oil-Based Photo-Crosslinked Polymer Networks

Novel soybean oil-based crosslinked polymer networks were prepared by UV photopolymerization and their mechanical properties were evaluated. Poly(ethylene glycol) diacrylate (PEGDA) and biodegradable poly(ε-caprolactone) diacrylate (PCLDA) were synthesized and used as crosslinking agent to form crosslinked polymer networks by UV-initiated free-radical polymerization with acrylated epoxidized soybean oil (AESO). The synthesis of acrylate end-capped macromers was confirmed using FT-IR and ¹H NMR spectroscopic techniques. Photopolymerization time, the composition of reaction mixture, and the type and length of crosslinking agent were changed to obtain crosslinked polymer networks with various mechanical properties. Polymers prepared from AESO and PCL degraded 6% of the initial weight in 24 days in phosphate buffer solution (pH 7.2) containing lipase enzyme. These potentially biodegradable and biocompatible polymers can be used as ecofriendly materials for biomedical and other applications to replace the existing petroleum-based polymers currently used.     

Photochemical Kinetic Modeling of Degradation of Aqueous Polyvinyl Alcohol in a UV/H<Subscript>2</Subscript>O<Subscript>2</Subscript> Photoreactor

This study presents a photochemical kinetics model to describe the degradation of water-soluble PVA (Polyvinyl Alcohol) polymer in a UV/H₂O₂ batch reactor. Under the effect of UV light, the photolysis of hydrogen peroxide into hydroxyl radicals can generate a series of polymer scission reactions. For a better understanding and analysis of the UV/H₂O₂ process in the cracking of the PVA macromolecules, a chemical reaction mechanism of the degradation process and a relevant photochemical kinetics model are developed to describe the disintegration of the polymer chains. Taking into account the probabilistic fragmentation of the polymer, the statistical moment approach is used to model the molar population balance of live and dead polymer chains. The model predicts the PVA molecular weight reduction, the acidity of the solution, and hydrogen peroxide residual. In addition to previously published data collected in this laboratory, a new set of experiments were conducted using a 500 mg/L PVA aqueous for different hydrogen peroxide/PVA ratios for model validation. Measurements of average molecular weights of the polymer, hydrogen peroxide concentrations and pH of the PVA solution were determinant factors in constructing a reliable photochemical model of the UV/H₂O₂ process. Experimental data showed a decrease in the PVA molecular weight and a buildup of the solution acidity. The experimental data also served to determine the kinetics rate constants of the PVA photochemical degradation and validate the model whose predictions are in good agreement with data. The model can provide a comprehensive understanding of the impact of the design and operational variables.     

Preparation of MgCr<Subscript>2</Subscript>O<Subscript>4</Subscript> from waste tannery solution and effect of sulfate,chloride, and calcium on leachability of chromium

This paper presents a study regarding the preparation of MgCr₂O₄ from waste tannery solution, and chromium leaching behavior is also investigated with varying amounts of sulfate, chloride and calcium. The phase transformation, crystallinity index and crystallite diameter were characterized using XRD, FT-IR and thermal analysis. A well-crystallized MgCr₂O₄ was successfully prepared at 1400 °C. The sintering temperature had a major impact on the formation of MgCr₂O₄ compared with sintering time. The MgCr₂O₄ phase was observed initially at 400 °C and its crystallite diameter increased with increasing temperature. The concentration of total chromium leached and Cr(VI) decreased gradually with increasing temperature. The considerable amount of Cr(VI) was found in the leachate at 300–500 °C caused by Cr(VI) intermediary products. Sulfate and chlorine could impact the transformation efficiency of chromium adversely, and chlorine has a more significant effect than sulfate. The presence of calcium disturbed the formation of MgCr₂O₄ and new chromium species (CaCrO₄) appeared, which resulted in a sharp increase in the concentration of leached Cr(VI). Incorporating Cr(III) into the MgCr₂O₄ spinel for reusable products reduced its mobility significantly. This was demonstrated to be a promising strategy for the disposal of chromium containing waste resource.     

Green Synthesis of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Cellulose/Polyvinyl Alcohol Hybride Aerogel and Its Application for Dye Removal

A novel Fe₃O₄/cellulose–polyvinyl alcohol (PVA) aerogel was successfully synthesized by an eco-friendly and facile method in this work. Cellulose/PVA matrix was prepared through an environmental friendly physical cross-linking process and further in-situ decorated with Fe₃O₄. Series of Fe₃O₄ decorated aerogels were prepared and the effects of Fe₃O₄ nanoparticles (NPs) on the aerogels were systematic investigated. As-prepared aerogels exhibited desirable properties including nanostructure, relatively high porosity, improved mechanical and superparamagnetism. The TEM results showed that Fe₃O₄ NPs were integrated in the three-dimensional matrix of cellulose/PVA with a diameter of 9–12 nm. Furthermore, the mechanical strength of the aerogels was significantly enhanced after the introduction of Fe₃O₄ NPs. Meanwhile, the obtained Fe₃O₄/cellulose/PVA aerogel exhibited excellent adsorption performance toward methyl blue dye, and can be reused through fenton-like catalysts oxidative degradation of organic dye in H₂O₂ solution. Therefore, they will have a great potential application as eco-friendly and economical adsorbents.     

Photo-Stabilisation and UV Blocking Efficacy of Coated Macro and Nano-Rutile Titanium Dioxide Particles in Paints and Coatings

Surface treated macro and nanoparticle TiO₂ samples have been prepared, characterised and their efficiency as UV blockers evaluated in clear coatings and paints. The particle size of the ‘base’ TiO₂ has been optimised to block UV radiation and the surface treatment developed to deactivate the photocatalytic activity of the surface of the TiO₂ particles. The resultant UV blockers have been evaluated in both solvent and water-based clear coatings. Nanoparticle TiO₂ has been prepared from ‘seed’ and the particle size was controlled by calcination. It was found that the choice of particle size is a compromise between UVA absorption, UVB absorption, visible transmission and photoactivity. It has been demonstrated that TiO₂ with a crystallite size of 25 nm yields a product with the optimum properties. A range of dispersants was successfully used to disperse and mill the TiO₂. Both organic and inorganic dispersants were used; 2-amino-2-methyl-1-propanol and 1-amino-2-propanol (MIPA) and P₂O₅ and Na₂SiO₃ respectively. The surface of the nano-TiO₂ was coated with mixed oxides of silicon, aluminium, zirconium and phosphorous. Addition of the resultant coated nano-rutiles to an Isocyanate Acrylic clear coating prolonged the lifetime of that coating compared to the blank. Generally, a surface treatment based on SiO₂, Al₂O₃ and P₂O₅ was more successful than one based on ZrO₂, Al₂O₃ and P₂O₅. Higher addition levels of the surface treatment were beneficial for protecting the polymeric coating. The UV blocker products were also evaluated in a water-based acrylic, first a water-based dispersion of the UV blocker was prepared before addition to the acrylic. The dispersions and resultant acrylic thin films were evaluated using UV/Vis spectroscopy and durability assessed. The ratio of absorbance at 300:500 nm for the water-based dispersion was shown to be a good predictor of both the transparency of the resultant acrylic thin film and the durability of that film, in terms of weight loss. Macro grade titanium dioxide pigments were also prepared and coated with treatments of silica, alumina and siloxane and their photo-stabilising activity in alkyd paint film assessed and found to be directly related to the electron–hole pair mobility and trapping as determined by micro-wave spectroscopy.     

Improvement of Physico-Mechanical Properties of Photo-Cured Chitosan Films with Ethylene Glycol Dimethacrylate and (2-Hydroxyethyl) Methacrylate

Chitosan, a natural polymer, was prepared by deacetylation of chitin which was obtained from dried prawn shell and was characterized. Thin chitosan film of chitosan was prepared by casting method from 0.2 % chitosan in 2 % acetic acid solution. Five formulations were developed with ethylene glycol dimethacrylate and (2-hydroxyethyl) methacrylate along with photo-initiator, Darocur-1664 (4 %). The chitosan film was soaked in the formulations at different soaking times and irradiated under UV-radiation at different intensities for the improvement of its physical and mechanical properties. The cured chitosan films were then subjected to various mechano-chemical tests like tensile strength, elongation at break, polymer loading, water absorption and gel content. The formulation containing 30 % ethylene glycol dimethacrylate and 66 % (2-hydroxyethyl) methacrylate showed the best performance at the 30th UV pass of UV-radiation for 3 min soaking time.     

Photochemical Degradation of Aqueous Polyvinyl Alcohol in a Continuous UV/H<Subscript>2</Subscript>O<Subscript>2</Subscript> Process: Experimental and Statistical Analysis

Polyvinyl alcohol (PVA), being a dominant contributor of total organic carbon (TOC) in textile wastewater, is not easily degradable by conventional methods of wastewater treatment. This study investigates the degradation of aqueous PVA in a continuous UV/H₂O₂ photoreactor since the feeding strategy of hydrogen peroxide proves to have considerable effects on the process performance. Response surface methodology involving the Box–Behnken method is adopted for the experimental design to study the effects of operating parameters on the process performance. Experimental analysis shows that the TOC removal varies from 16.11 to 42.70 % along with a reduction of the PVA molecular weights from 56.7 to 95.3 %. The TOC removal is significantly lower than the molecular weight reduction due to the generation of the intermediate products during oxidation. Operating the UV/H₂O₂ process in a continuous mode facilitates the degradation of highly concentrated polymeric solutions using a relatively small hydrogen peroxide concentration in the feed with a small residence time ranges from 6.13 to 18.4 min.     

Improvement of Physico-mechanical Properties of Chitosan Films by Photocuring with Acrylic Monomers

Natural polymer, chitosan was obtained from dried prawn shell waste through the preparation of chitin and was characterized. Thin film of chitosan was prepared by casting method from its 2% chitosan solution. Mechanical properties like tensile strength (TS), elongation at break (Eb) of chitosan film were studied. Five formulations were developed with 2-ethyl-2-hydroxy methyl-1,3-propandiol trimethacrylate (EHMPTMA), a trifunctional monomer and 2-ethylhexyl acrylate (EHA), a monofunctional monomer in the presence of photoinitiator Darocur-1664 (2%). The film was soaked in those monomer formulations in dissimilar soaking times and irradiated under UV-radiation at different radiation intensities for the improvement of the properties of chitosan film. The cured films were then subjected to various characterization tests like TS, Eb, polymer loading (PL), water absorbency, gel content etc. The formulation, containing 25% EHMPTMA and 73% EHA showed the best performance at 10th UV passes of UV radiation for 4 min soaking time.     

Photocatalytic Degradation of Poly(Vinyl Alcohol) on Pt/TiO<Subscript>2</Subscript> with Fenton Reagent

In this research Fenton reagent (Fe²⁺/H₂O₂) was investigated as oxidants to degrade poly (vinyl alcohol) (PVA). The role of nano-TiO₂ photocatalyst was discussed as an additive in Fenton reagent (Fe²⁺/H₂O₂). Pt/TiO₂ composites were also synthesized by photo-reaction to be used as additive in Fenton reagent. The rapid degradation of PVA was obtained when Pt/TiO₂ composites served as photocatalyst. The different photocatalytic efficiency of Pt/TiO₂- Fenton reagent (Fe²⁺/H₂O₂) was studied compared with TiO₂- Fenton reagent (Fe²⁺/H₂O₂) during the degradation of PVA.     

Reductive decomposition of waste gypsum with SiO<Subscript>2</Subscript>, Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> additives

From the point of view of a sustainable and environment-friendly society based on the recycling of material resources, it is preferable to utilize waste gypsum as a substitute for lime, which is currently produced by the calcination of limestone. In the present work, the reductive decomposition of CaSO₄ was investigated under an atmosphere of CO: 2 vol%, CO₂: 30 vol%, with N₂ as a carrier gas without and with the addition of SiO₂, Al₂O₃, or Fe₂O₃. It was found that the decomposition temperature of CaSO₄ was significantly reduced from 1673 K to 1223 K when only 5 wt% Fe₂O₃ was added to CaSO₄. In the case of the addition of SiO₂ or Al₂O₃ to CaSO₄, the decomposition temperature was reduced from 1673 K to 1623 K. This was due to the formation of composite oxides (calcium ferrite, calcium silicate, or calcium aluminate) during the reaction of CaSO₄ with the additives at a lower temperature. In addition, the formation of unfavorable product CaS was inhibited in the presence of 5 wt% Fe₂O₃, and this inhibition effect further increased as the addition of Fe₂O₃ was increased. In contrast, no significant effect on the inhibition of CaS formation was observed on the addition of SiO₂ or Al₂O₃.     

Removal of Reactive Blue 19 dye from synthetic wastewater using UV/H2O2 and UV/Cl advanced oxidation processes

The textile and dyeing industries are among the largest water-consuming and polluting industries in the world. The most important feature of the textile dyeing industry wastewater is its color, due to the use of colored materials. Most of these dye compounds are resistant to conventional purification methods and their biodegradation is very low through secondary purification processes, resulting in incomplete removal. Therefore, selecting the optimal method to remove these color compounds is essential. In this study, we studied the removal of an organic dye contaminant (Reactive Blue dye 19 [RB19]) using advanced oxidation processes (AOPs). For this purpose, ultraviolet (UV) mercury lamps with a wavelength of 254 nm and a voltage of W16 inside a reactor were used as an energy source. The experiments were performed in a collimated beam reactor inside a dark chamber. Two oxidizers, sodium hypochlorite (NaOCl) and hydrogen peroxide (H₂O₂), were used to remove RB19 from the artificial sewage stream. Removal of RB19 with a concentration of 20 mg/L with variable pH (5, 7, and 9), oxidant concentrations (5, 10, and 20 mg/L), and time (5, 10, 15, and 30 min) were investigated during the processes of photolysis, chemical oxidation (by H₂O₂ and NaOCl), and UV/NaOCl and UV/H₂O₂ AOPs. The photolysis process did not remove the RB19. The highest removal efficiencies of RB19 by chemical oxidation processes with NaOCl and H₂O₂, UV/NaOCl, and UV/H₂O₂ at optimal conditions (pH = 5, [oxidant] = 20 mg/L, RB19 = 20 mg/L, and radiation intensity of 1005 mJ/cm²) were 64.49%, 0.88%, 99.7%, and 13.31%, respectively. These results indicate that the hydroxyl radical was produced, under optimum conditions, more in the acidic medium; thus, the RB19 removal efficiency was higher in the acidic medium. The combination of UV rays with oxidants resulted in the production of more hydroxyl radicals and increased removal efficiency.     

Chemical Crosslink Degradable PVA Aqueous Solution by Potassium Persulphate

The aim of this paper is to study the influence of the K₂S₂O₈ content on the properties of poly (vinyl alcohol, (PVA). Firstly, PVA was dissolved in distilled water by heating by heating at 70 °C and then K₂S₂O₈ was added in PVA solution under stirrer. The viscosity of PVA solution in the presence of K₂S₂O₈ was analyzed by Brookfield Viscometers. The effects of K₂S₂O₈ contents, PVA solution, temperature and reaction time on the viscosity of PVA solution were investigated. This was confirmed by Brookfield Viscometers. It is clear that the viscosity of PVA solution in the presence of K₂S₂O₈ increased as function of reaction time and PVA content in solution. Rate of modified PVA was proportional to K₂S₂O₈ contents and temperature and its activation energy was 16 kJ/mol. The structure of PVA in the presence of K₂S₂O₈ changed from original PVA confirmed by ATR-FTIR and solid state NMR. In addition, the thermal properties of PVA containing K₂S₂O₈ were also studied by TGA.     

Mechanical properties of incineration bottom ash: The influence of composite species

The mechanical properties, including strength, deformational behavior, and wetting softening phenomena of municipal solid waste incinerator (MSWI) bottom ash are one of the major concerns for reuse applications. However, owing to the complex constituents of municipal solid waste, the properties of MSWI bottom ash are often highly variable. A series of artificial specimens with controlled chemical components were tested in this study. The test results show that the artificial bottom ash possesses the following mechanical characteristics: (1) for the strength, the frictional angles of the bottom ash under dry and saturated conditions vary from 34.8° to 51.1° and 26.0° to 37.2°, respectively; (2) for the deformation, the shear stiffness increases with the normal stress arises and degrades upon increased shearing; (3) significant wetting degradation of the strength and stiffness were observed.The multi-variable regression analysis was conducted to evaluate the associated influence of the chemical components on the strength. Among the evaluated components, Fe₂O₃ and Al₂O₃ are key factors; an increase in either results in higher strength at both dry and saturated conditions. The results were used to propose empirical relationships for ?_dry and ?_sat, expressed in terms of Fe₂O₃ and Al₂O₃. Accordingly, a strength classification chart is proposed for engineering purposes.     

Effects of Nitrogen Supply on the Sensitivity to O3 of Growth and Photosynthesis of Japanese Beech (Fagus crenata) Seedlings

To obtain basic information for evaluating critical levels of O₃ under different nitrogen loads for protecting Japanese beech forests, two-year-old seedlings of Fagus crenata Blume were grown in potted andisol supplied with N as NH₄NO₃ solution at 0, 20 or 50 kg ha⁻¹ year⁻¹ and exposed to charcoal-filtered air or O₃ at 1.0, 1.5 and 2.0 times the ambient concentration from 16 April to 22 September 2004. The O₃ induced significant reductions in the whole-plant dry mass, net photosynthetic rate at 380 μmol mol⁻¹ CO₂ (A ₃₈₀), carboxylation efficiency (CE) and concentrations of ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco) and total soluble protein (TSP) in the leaves. The concentrations of Rubisco and TSP were negatively correlated with the concentration of leaf acidic amino acid, suggesting that O₃ enhanced the degradation of protein such as Rubisco. The N supply to the soil did not significantly change the whole-plant dry mass and A ₃₈₀, whereas it significantly increased the CE and concentrations of Rubisco and total amino acid. No significant interactive effects of O₃ and N supply to the soil were detected on the growth, photosynthetic parameters and concentrations of protein and amino acid in the leaves. In conclusion, N supply to the soil at ≤50 kg ha⁻¹ year⁻¹ does not significantly change the sensitivity to O₃ of growth and net photosynthesis of Fagus crenata seedlings.     

Groundwater treatment and aquatic toxicity reduction at a chemical production site

Contaminated groundwater at a chemical antioxidant and phenolic resin chemical production site was subjected to treatability studies to develop design criteria for surface water discharge. Raw groundwater required pretreatment for total suspended solids (TSS) and color removal prior to treatment by ultraviolet light/hydrogen peroxide (UV/H₂O₂). Because of high capital and operating costs for UV/H₂O₂, biological treatment was evaluated as an alternate. Respirometric analyses showed that completely mixed activated sludge could be applied as a treatment technology to the groundwater. Biotreatment resulted in an approximately 70 percent reduction in soluble chemical oxygen demand (SCOD). Residual SCOD was recalcitrant to further biodegradation. The treated effluent was tested for aquatic toxicity using fathead minnows (Pimephales promelas) and Ceriodaphnia dubia and was found to be toxic. Toxicity reduction of biotreatment effluent was evaluated in bench-scale experiments using activated carbon adsorption, filtration, and UV/H₂O₂. Subsequent toxicity testing showed that filtration alone could reduce the bioeffluent toxicity and that residual SCOD was not the primary source of toxicity.     

Citric Acid and Vitamin C as Coupling Agents for the Surface Coating of ZrO<Subscript>2</Subscript> Nanoparticles and Their Behavior on the Optical,Mechanical, and Thermal Properties of Poly(vinyl alcohol) Nanocomposite Films

A series of bio-nanocomposites (BNC)s were fabricated through solution casting method. At first, the surfaces of ZrO₂ NPs were functionalized with citric acid and Vitamin C as green modifier agents. Then, PVA as polymer matrix was embedded with different contents (4, 8 and 12 wt%) of modified ZrO₂ (m-ZrO₂) NPs with the aim of ultrasonic irradiation process. The resulting BNCs were studied by various techniques. Thermal stability of obtained BNCs was enhanced after NPs’ addition to the PVA matrix. Optical activity of these new BNCs makes them potential candidate for UV shielding material. Lastly, the tensile strengths of the BNCs were increased in comparison to the pure PVA.