共查询到15条相似文献,搜索用时 281 毫秒
1.
太阳能吸热器换热管蓄热数值模拟与试验研究 总被引:2,自引:0,他引:2
对以高温共晶盐LiF—CaF2为相变材料(PCM)和以干空气为工质的相变蓄热系统,采用焓方法建立了以控制体单元为对象的单管相变蓄热模型,并对系统进行了数值分析,得到了循环工质气体出口温度、相变材料容器最高温度和平均壁温等参数的瞬态变化曲线,实验研究了吸热器换热管的蓄傲热性能,分析了工质进口温度、输入热流级工质流量对工质出口温度、PCM容器平均壁温及最高壁温的影响。计算结果和试验表明单元换热管的蓄傲热性能达到了设计要求,试验结果与数值计算吻合良好。 相似文献
2.
太阳入射热流对吸热器换热的影响 总被引:1,自引:1,他引:1
空间太阳能热动力发电系统是非常有前景的未来空间能源供应系统。吸热器的入射热流分布将影响到换热管的传热以及系统的寿命,采用焓法处理相变区的传热,建立了太阳能热动力发电系统吸势器换热管三维换热模型,计算得到在轨道周期内对应三种入射热流的换热管的温度场、工质的出口温度变化、相变材料熔化率等重要的结果,并进行了比较、分析。 相似文献
3.
4.
高温熔盐相变蓄热材料 总被引:5,自引:0,他引:5
高温蓄热技术是太阳能热动力发电系统的关键技术之一,通常利用相变材料(PCM)固液相变时的熔化潜热来蓄热。在轨道的日照期,聚能器将截取的太阳能聚集到吸热器圆柱形腔内,被吸收转化成热能,其中一部分热能传递给循环工质以驱动热机发电,其余的热能被封装在单元换热管上多个小容器内的PCM吸收储存起来,此时PCM部分或全部变为液态。在轨道的阴影期,小容器内的PCM部分或全部变为固态,储存的能量被释放出来,使出口的循环工质温度仍能维持在循环所要求的最低峰值温度上。保证空间站处于阴影期时热机仍能连续工作,保证连续供电。太阳能利用中… 相似文献
5.
太阳能热动力发电系统吸热器换热管试验及数值模拟 总被引:4,自引:0,他引:4
吸热器换热管地面试验是空间太阳能热动力发电系统吸热/蓄热器研制的重要阶段,是为了验证相变材料的蓄放热性能。对以共晶盐LiF—CaF2为蓄热介质的换热管进行了27个周期共2511分钟的地面试验,包括变参数试验和稳态试验,获得了容器表面温度和工质出口温度等试验结果。利用焓法建立相变蓄热换热管试验的传热模型,采用试验参数对地面试验进行了数值模拟,得到的结果与试验结果进行了比较,两者比较接近。证明了地面单管试验的成功性,也验证了换热管传热分析软件的可靠性。 相似文献
6.
为探究相变温度对相变材料回填地埋管换热器传热性能的影响,建立管内流体换热、回填区域相变换热及土壤换热的三维耦合传热数值模型,利用焓-多孔介质模型对相变区域相变问题进行处理,研究夏季间歇运行工况下不同相变温度回填材料对埋管换热器传热性能的影响。结果表明:添加PCM,可有效提高换热量,短期内缓解埋管周围热积聚,利用相变温度18℃的PCM回填,单位井深换热量至少比普通材料回填提高49.54%;在间歇运行初期,换热量随相变温度的升高逐渐减小,低相变温度的PCM可明显改善埋管换热量,但随着时间的进行,较高相变温度PCM回填对换热器换热量的改善效果优于前期低相变温度。此外,在运行期间,不同相变温度的PCM表现出不同的熔化、凝固特性,当PCM的熔化、凝固过程交替进行时,可减缓土壤温度在运行期间内波动幅度。 相似文献
7.
8.
9.
针对管壳式相变蓄热器换热速率较慢的问题,建立多管束大空间相变蓄热器模型数值模拟的研究换热管排列方式及翅片参数对换热效果的影响。通过观察温度和速度场、固液相界面、Nu及液相分数与时间的关系,分析蓄/放热传热过程。研究结果表明:采用正三角排列可增强换热管间热扰的影响,提高相变材料(phase change material, PCM)熔化速率;蓄热过程中传热以自然对流为主,放热过程中传热以导热为主;合理调整不同位置换热管节距,可改善蓄热器温度分布均匀性;适当增加翅片数量及高度有利于提高PCM换热速率,蓄热器最佳翅片数量为8组,高度为25 mm。 相似文献
10.
高温相变蓄热器是空间太阳能热动力发电系统的关键部件之一,相变材料(PCM)蓄热是其中的关键技术。对以LiF-CaF2为PCM和以干空气为工质的蓄热系统进行了地面实验,并分别建立了相应条件下填充纯PCM和泡沫复合相变材料(FCPCM)的蓄热单元管数学模型。经过数值计算得到结果表明,纯PCM蓄热单元管计算值与实验数据吻合得很好,表明了计算模型的有效性;此外,对填充纯PCM和FCPCM的蓄热单元管的计算结果进行了比较,结果表明,泡沫的填充强化了PCM的导热性能,提高了蓄热系统的热性能。 相似文献
11.
Energy analysis of space solar dynamic heat receivers employing solid–liquid phase change storage is developed. The heat receiver is a critical component of a solar dynamic system. Phase change thermal energy storage is used in the heat receiver. The energy analysis presented here can be used to understand the energy transfer in the heat receiver and thermal energy storage in phase change materials (PCM). The heat receiver cavity radiation mathematical model and the working fluid tube heat model are established. Energy loss, energy absorbed by gas, the latent and sensible thermal energy storage in PCM, maximum tube temperature, gas outlet temperature and liquid PCM fraction were calculated. The results are analyzed and could be used in heat receiver design. 相似文献
12.
To solve the problems associated with employing the single melt point phase change material in a heat receiver for the NASA 2 kW solar dynamic power system, this paper presents a practically easy to carry-out PCM receiver model composed of three different phase change temperature materials together with the corresponding physical model. A numerical solution is also given by which the maximal temperature for heat transfer, working fluid exit temperature, and liquid PCM fraction of the total heat transfer tube in whole are calculated. Furthermore, the results are compared with those obtained from the single PCM heat receiver. The results show that it is possible to improve the receiver performance and to reduce both the fluctuation of working fluid temperature and the weight of the heat receiver. All results of the calculation can be used to guide the heat receiver design. 相似文献
13.
14.
In this paper, the phase change temperature, latent heat and thermal stability of the capric acid–stearic acid binary system and 48# paraffin–liquid paraffin binary system were experimentally studied. The experimental results showed that the phase change temperature and phase change latent heat change with the content of the component. The phase change temperature of binary mixtures changes in a wide range, so they can be used in different fields by adjusting mixing ratio. The phase change latent heat of fatty acid mixtures is higher than that of paraffin mixtures. The thermal stability of fatty acid mixtures is better than that of paraffin mixtures. The mixtures used in the phase change material (PCM) wall or the PCM floor as energy storage materials are given in the paper. 相似文献