Experimental investigations on the effect of fuel injection parameters on diesel engine fuelled with biodiesel blend in diesel with hydrogen enrichment

Fuel injection pressure and injection timing are two extensive injection parameters that affect engine performance, combustion, and emissions. This study aims to improve the performance, combustion, and emissions characteristics of a diesel engine by using karanja biodiesel with a flow rate of 10 L per minute (lpm) of enriched hydrogen. In addition, the research mainly focused on the use of biodiesel with hydrogen as an alternative to diesel fuel, which is in rapidly declining demand. The experiments were carried out at a constant speed of 1500 rpm on a single-cylinder, four-stroke, direct injection diesel engine. The experiments are carried out with variable fuel injection pressure of 220, 240, and 260 bar, and injection timings of 21, 23, and 25 °CA before top dead center (bTDC). Results show that karanja biodiesel with enriched hydrogen (KB20H10) increases BTE by 4% than diesel fuel at 240 bar injection pressure and 23° CA bTDC injection timing. For blend KB20H10, the emissions of UHC, CO, and smoke opacity are 33%, 16%, and 28.7% lower than for diesel. On the other hand NOx emissions, rises by 10.3%. The optimal injection parameters for blend KB20H10 were found to be 240 bar injection pressure and 23 °CA bTDC injection timing based on the significant improvement in performance, combustion, and reduction in exhaust emissions.     

Effect of hydrogen enrichment and TiO2 nanoparticles on waste cooking palm biodiesel run CRDI engine

In this study, we deal with the production and utilization of waste-cooking palm biodiesel (WCB) and.evaluated the influence of the addition of titanium dioxide (TiO₂) nanoparticles in hydrogen-enriched single-cylinder CRDI diesel engine. XRD, SEM, and EDX decide the structure and morphology of TiO₂ nanoparticles. The TiO₂ nanoparticles were dispersed in the tested fuels at a dosage of 50–75 ppm with the aid of ultra-sonication. Based on the oxidation stability study, the B20 + 75 ppm (TiO₂) fuel blend is the pilot fuel for the engine test. Further, the engine is enriched with a hydrogen (H₂) flow of 10 lpm. Results revealed that the performance parameters were improved with the addition of H₂ enrichment and TiO₂ nanoparticles compared to D. The brake thermal efficiency of the engine was improved by 8.21%. In comparison, brake-specific fuel consumption decreased by 42.86%. Furthermore, adding nanoparticles also reduced CO and HC emissions by 74% and 27.27%, respectively, whereas the NO_x emission was slightly increased. Thus, the findings demonstrated that hydrogen-enriched nanoparticles added to biodiesel might be considered a substitute for fossil fuels and report a positive impact on diesel engine performance without requiring significant modifications.     

Effect of natural antioxidant additive on hydrogen-enriched biodiesel operated compression ignition engine

The environmental degradation and depletion of fossil fuel, urges the need of renewable fuel for IC engines. Among the renewable fuel, biodiesel are widely used as alternative fuel but for recent years hydrogen is also considered as alternative fuel because of zero emission but it possess higher auto ignition temperature. In order to reduce the self-ignition temperature of hydrogen and another liquid fuel is mixed and operated as a dual fuel mode condition in CI engine. The current investigation aims to analyse the impact of natural antioxidant additive on hydrogen-enriched biodiesel operation in a diesel engine. During the experimentation process hydrogen is admitted at the intake manifold and B20 blend of juliflora biodiesel is injected in combustion cylinder. The three test fuel samples are used for the experimentation process such as diesel, B20 and B20 with hydrogen in different flow rates such as 8, 10, 12, 16,20lpm. B20 with hydrogen shows an increment of brake thermal efficiency (BTE). Among the test fuels B20 + 16lpm and B20 + 20lpm blends have better improvement of BTE of 28.815% and 28.32%, which is higher than the conventional engine at maximum load CO, HC emission is also lower for B20 + 16lpm and B20 + 20lpm than other blends but the NO_x emission increases of 26 and 28% than diesel respectively. In order to minimize the NO_x emission, natural antioxidant additive Melia Azedarach (MA) of 1000 ppm is added to B20 + 16lpm and found that B20 + 16lpm with MA shows an improvement of BTE 2.17% higher than B20 + 16lpm without additive and the NO_x emission for B20 + 16lpm with additive is 1079 ppm, which is 21.9% lower than B20 + 16lpm without additives. Therefore B20 + 16lpm with additive is superior than other test blends.     

Effect of hydrogen enrichment in the intake air of diesel engine fuelled with honge biodiesel blend and diesel

In the current investigation, the enrichment of hydrogen with the honge biodiesel blend and diesel is used in a compression ignition engine. The biodiesel is derived from the honge oil and mixed with diesel fuel by 20% (v/v). Thereafter, hydrogen at different volume flow rates (10 and 13 lpm) is introduced into the intake manifold. The outcomes by enrichment of hydrogen on the performance, combustion and emission characteristics are investigated by examining the brake thermal efficiency, fuel consumption, HC, CO, CO₂, NOₓ emissions, in-cylinder pressure, combustion duration, and rate of heat release. The engine fuelled with honge biodiesel blend is found to enhance the thermal efficiency, combustion characteristics. Compare to diesel, the BTE increased by 2.2% and 6% less fuel consumption for the HB20 + 13H₂ blend. Further, reduction in the emission of exhausts gases like CO and HC by 21% and 24%, respectively, are obtained. This is due to carbon-free structure in hydrogen. Moreover, due to high pressure in the cylinder, there is a slight increase in oxides of nitrogen emission compare to diesel. The combustion characteristics such as rate of heat release, combustion duration, and maximum ₂rate of pressure rise and in-cylinder pressure are high due to hydrogen.     

Effect of fuel opening injection pressure and injection timing of hydrogen enriched rice bran biodiesel fuelled in CI engine

Fuel opening injection pressure and injection timing are important injection parameters, and they have a significant influence on engine combustion, performance, and emissions. The focus of this work is to improve the performance and emissions of single-cylinder diesel engines by using injection parameters in engines running with rice bran biodiesel 10% blend (RB10+H₂) and 20% blend (RB20+H₂) with a fixed hydrogen flow rate of 7 lpm. In addition, hydrogen and biodiesel are excellent alternatives to conventional fuels, which can reduce energy consumption and strict emission standards. The investigation is conducted for three different opening injection pressure of 220, 240, 260 bar, and four different injection timings of 20°, 22°, 24°, and 26° bTDC. Results indicate that the sample ‘RB10+H₂’ provides 3.32% higher BTE and reduces the fuel consumption by 13% as diesel fuel. The blend RB10+H₂ attributes a maximum cylinder pressure of 68.7 bar and a peak HRR value of 49 J/ºCA. Further, compared to diesel, RB10+H₂ blend emits lower CO, HC, and smoke opacity by 17%, 22%, and 16%, respectively. However, an almost 12% increase of nitrogen oxides for the RB10+H₂ blend is observed. However, with advanced injection timing and higher opening injection pressure, NOx emissions is slightly increased.     

The characteristics of waste-cooking palm biodiesel-fueled CRDI diesel engines: Effect hydrogen enrichment and nanoparticle addition

The influence of iron nanoparticle (INP) addition (75 ppm) and hydrogen enrichment (10 lpm) with waste cooking palm biodiesel blend (WCB) on a CRDI diesel engine is evaluated. A blend of 20% WCB and 80% diesel is used, and the dosing level of INP has been kept at 75 ppm, which has been decided based on the oxygen content of biodiesel. Results indicate that the combination of H₂ enrichment and INP addition improves the BTE and BSFC of biodiesel blends as that of diesel. A maximum improvement of BTE of 7.1% than that of diesel is obtained at 90% loading. The combined impact of better hydrogen combustion characteristics and improved air-fuel mixing with nanoparticles reduces CO and HC emissions by 37.5% and 41.8%, respectively, for the WCB fuel sample. However, NO_X emission shows an elevation of 27.4% compared to diesel. Combustion parameters, namely ICP (80.1 bar) and HRR (89.5 J/˚CA) indicate an improvement of 5.3% and 6.7% compared to diesel for WCB + INP + H₂. This is owing to the combination of hydrogen's rapid flame speed and INP-added biodiesel's increased thermal conductivity.     

Effect of hydrogen and ethanol addition in cashew nut shell liquid biodiesel operated direct injection (DI) diesel engine

In this experimental research, the hydrogen gas at a different flow rate (4 lpm, 8 lpm, & 12 lpm) is introduced into the intake port of a diesel engine fueled with B20 (20% CNSL (Cashew nut shell liquid) + 80% diesel) biodiesel blend to find out the best H₂ flow rate. Then, ethanol-blended (5%, 10%, and 15% by volume) B20 blend along with the best H₂ flow rate are tested in the same engine to examine the engine performance. The experimental results showed that B20 with 8 lpm H₂ flow gives the maximum brake thermal efficiency and subsequently reduces the BSFC. Furthermore, by blending ethanol with the B20 blend, the BTE of the engine is improved further. The 10% ethanol blended B20 blend with 8 lpm hydrogen flow gives the maximum BTE of 37.9% higher than diesel whose values are 33.6% at full load. Also, this fuel combination led to the maximum reduced levels of CO and HC emissions with an increase in exhaust gas temperature and NOx emissions. From the results, the 10% ethanol blended B20 blend with 8 lpm H₂ flow dual-fuel configuration is recommended as an alternative to sole diesel fuel.     

Combined impact of varying biogas mass flow rate and rice bran methyl esters blended with diesel on a dual-fuel engine

ABSTRACT

For fetching day-to-day energy needs, current energy requirement majorly depends on fossil fuels. But ambiguous matter like abating petroleum products and expanding air pollution has enforced the experts to strive for another fuel which can be used as an alternative or reduce the applications of fossil fuels. Considering the issues, the main objective of the present study is to find the feasibility by using blends of rice bran oil biodiesel and diesel which are used as pilot fuels by blending 10% and 20% biodiesel in fossil diesel and biogas, introduced as gaseous fuel by varying its mass flow rate in a dual-fuel engine mode. An experimentation study was carried out to find the performance and emission parameters of the engine relative to pure diesel. The results were very much similar to the majority of researchers who used biodiesel and gaseous fuels in a dual-fuel engine. Brake specific fuel consumption (BSFC) of the engine was noticed to have increased, while brake thermal efficiency was on the lower side in dual fuel mode in comparison with regular diesel. In relation with conventional diesel, it was noticed that combined effect of rice bran methyl esters and varying mass flow rate of biogas showed a decrement in NO _x and smoke emissions, whereas HC and CO exhalations were on higher side when biogas and biodiesel were utilized collectively in dual-fuel engine. Hence, it was concluded that combination of blends of biodiesel and diesel and introduction of biogas in the engine can be a promising combination which can be used as a substitute fuel for addressing future energy needs.     

Partial hydrogenation and hydrogen induction: A comparative study with B20 operation in a turbocharged CRDI diesel engine

Numerous studies explored the possibility and effective strategies for supplementing hydrogen along with fossil or biofuels on internal combustion engines. Hydrogen is also being employed for formulating fuels such as hydrogen compressed natural gas in the gaseous form and hydrogenated biofuels in the liquid form. The present study evaluates (i) hydrogen usage on the fuel formulation and (ii) investigates the engine operation of an automotive turbocharged diesel engine operated with karanja biodiesel blended diesel (B20) as a reference fuel. Existing literature outlines that biodiesel blends possess lower energy content and emit higher nitric oxide (NO) emission than fossil diesel. The present research paper partially hydrogenates karanja biodiesel using an autoclave reactor with a palladium catalyst to increase the saturation levels and mitigate the biodiesel-NO penalty. Besides, the drop in energy release of B20 is compensated through the provision of hydrogen induction along the intake manifold. The hydrogen flow rates to the turbocharged engine are maintained at a fixed energy share of 10%. Both biodiesel and hydrogenated biodiesel were blended on a volume basis (20%) with fossil diesel (80%) and are designated as B20 and HB20, respectively. The test results reveal that HB20 effectively mitigates the biodiesel-NO penalty with a maximum reduction of 29.8% compared to B20. Further, hydrogen induction yielded a significant improvement (23.7%) in fuel consumption with HB20 relative to B20 without hydrogen addition. The compounding effect of hydrogen usage on the engine operation and fuel formulation exhibited a better performance and emission trade-off at mid load conditions.     

Experimental evaluation of hydrogen enrichment in a dual-fueled CRDI diesel engine

The influence of hydrogen enrichment on the dieselengine fueled with diesel and palm biodiesel blend (P20) is investigated in this study. The hydrogen is injected into the intake manifold at different flow rates of 7 lpm and 10 lpm for each loading condition of 30%, 60%, 80%, 90%, and 100%, respectively. Hydrogen enrichment improves the BTE and BSEC due to its high calorific value and decreases emissions like HC, CO, and CO₂ due to its carbon-free structure. However, due to a rise in EGT, NO_x emission has increased. With the addition of hydrogen, combustion properties such as in-cylinder pressure (ICP), heat release rate (HRR), and ignition delay (ID) improve while the combustion duration (CD) drops. Compared to P20 fuel,P20 + 10H₂ has a 28% increase in BTE and a 20% decrease in BSEC at 90% load. Similarly, HC, CO, and CO₂ emissions decrease by 16%, 35%, and 12%, while NO_x emission increases by 13% compared to P20. At full load, P20 + 10H₂increasesin-cylinder pressureand heat release ratebyupto 1–5%, while CD decreases by 12.5% compared to the P20 blend.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

Influence of fuel oxygen content on diesel engine exhaust emissions

The aim of this work was to investigate: the intersolubility of mixtures of rapeseed oil methyl esters, diesel fuel and ethanol; to determine the dependence of solubility upon temperature and finally to evaluate emissions of exhaust gases of these stable fuel mixtures.Bearing in mind that the cloud point is an important parameter of diesel fuel, the variation of solubility of a tri-component rapeseed oil methyl ester–diesel fuel–ethanol (RME–D–E) system at temperature (20; 0; −10 °C) was also investigated. It was found that temperature decrease causes the RME–D–E system solubility limits to become narrow. Solubility investigations allowed to determine the optimal solubility limits and select mixtures containing 6.9–25.7% of oxygen for engine tests. The highest oxygen content in biodiesel fuel permitting the engine to work normally at 2000 and 1200 min⁻¹ was 19.5%. The lowest concentration of PAH and smoke index of exhaust gases were determined when fuel mixtures contained 19.5% of oxygen. The CO concentration depended on the rotational speed and varied from 10.7% to 16.8%. Apparently, optimal diesel fuel on this basis will contain from 15% to 19% of oxygen.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Influence of surfactants on quaternary emulsion blend and experimental investigations on the influence of hydrogen enriched quaternary blend in DICI engine

In this research work, phase behaviour of the synthesized Schizochytrium algae biodiesel, diesel and octanol was studied with water in oil emulsions (Quaternary blend). The effects of different hydrophilic lipophilic balance were investigated by varying the ratio of Span 80 and Tween 80 (20–100%) in the quaternary blend to find an optimum HLB number. The optimum fuel blend of HLB number 12 (Span 20%: Tween 80%) showed no phase separation for 25 days. The influence of hydrogen addition in quaternary blend (QB20) and biodiesel blend (B20) under variable hydrogen flow rates (1 l/min and 2 l/min) was investigated to improve the engine parameters using dual fuel mode of operation. The dual fuel mode of operation increased the brake thermal efficiency from 29.71% for quaternary blend to 32.01% with the addition of 2 l/min hydrogen. In terms of emission, UHC was reduced by 30% and 5% for QB20 + 1 l/m H2 and QB20 + 2 l/m H2, respectively. The maximum of 11% CO emission was reduced by the hydrogen inducted QB20 + 2 l/m H2 blend.     

Effect of changing injection pressure on Mahua oil and biodiesel combustion with CeO2 nanoparticle blend on CI engine performance and emission characteristics

Alternative fuels have sparked a lot of interest as oil deposits have decreased and environmental concerns have grown. Biodiesel is an alternative fuel that is being researched as a possible replacement for fossil fuels. In the current investigation, the combustion performance, and emission characteristics of CI(Compression Ignition) engine were examined by changing the fuel injection pressure (180, 200, 220 and 240 bar). The biodiesel (B20) used in this analysis was obtained from Mahua oil at 20% v/v blended with neat diesel (20% Mahua Biodiesel + 80% Diesel). CeO₂(Cerium Oxide) nanoparticles were introduced to the B20 fuel at four distinct concentrations are 25, 50, 75, and 100 ppm. Performance characteristics such as BTE(Brake Thermal Efficiency) and BSFC(Brake Specific Fuel Consumption) were inferior to diesel, at 240 bar B20 with 25 ppm CeO₂ indicated 1.9% increased BTE and 3.8% reduced BSFC compared B20 and 6% lower EGT (Exhaust Gas Temperature) compared diesel. At 200 bar, fuel samples indicated slightly higher In-Cylinder pressure and lower HRR (Heat release rate) compared to diesel. At 200 bar FIP(Fuel Injection Pressure), HC(Hydro Carbon) and CO(Carbon Monoxide) emissions were reduced significantly compared to diesel. The largest reduction in smoke opacity and NOx(Nitrous Oxide) emissions were observed at 240 bar with 75 ppm dosage, but CO₂(Carbon Dioxide) emissions were higher at 220 bar.     

Emission analysis on compression ignition engine fueled with lower concentrations of Pithecellobium dulce biodiesel‐diesel blends

The present study investigates the effect of Pithecellobium dulce biodiesel (PDBD) blends with diesel fuel on compression ignition (CI) engine emissions. Initially, PDBD was prepared by using a base transesteri?cation process. The GC‐MS, ¹H NMR, and Fourier transform infrared characterization of PDBD was carried out, and fuel properties were determined. The experiments were conducted on a single cylinder, CI engine using three blended fuels: PDBD5 (5% biodiesel and 95% diesel), PDBD10 (10% biodiesel and 90% diesel), and PDBD20 (20% biodiesel and 80% diesel). The experimental outcomes revealed that 20% of PDBD reduces 19.64% carbon monoxide, 17.64% hydrocarbon, and 6.73% oxides of nitrogen emissions. Furthermore, from this study, it was inferred that the PDBD20 blend could be used as an alternative fuel for CI engines with no modi?cations in engine design.     

Investigation on combustion and emission characteristics of hydrogen-enriched dual-fuel engine operated under waste frying oil biodiesel

Using nonedible waste frying oil (WFO) as biodiesel and hydrogen in the mix composition may partly replace significant quantities of diesel fuel and help reduce fossil fuel reliance. The combination of diesel fuel, waste-fired biodiesel, and hydrogen gas can improve the performance, combustion, and emissions of single-fuel and dual-fuel diesel engines. This may lead to a novel alternative fuel mix pattern and modification for diesel engines, which is the research gap. Although there has been some research on waste-fired biodiesel and hydrogen gas-powered dual-fuel engines with the goal of partly replacing fossil fuels to a larger degree, there has been very little progress in this area. As a result, the current research effort focuses on using diesel fuel (100%, 30%, and 60%), waste-fired biodiesel (at 100%, 70%, and 40%), and hydrogen gas as fuel sources (5 and 10 liters per minute [LPM]). According to the current experiment, it was perceived in both dual-fuel and single-fuel modes. Under duel-fuel mode, the engine results for WFOB70D30 + H10 fuel blend had higher 4.2% (brake thermal efficiency [BTE]), 19.72% (oxides of nitrogen [NO_x]), and 9.09% (ignition delay [ID]) with a minimal range of (in-cylinder pressure, MFB, volumetric efficiency and heat release rate [HRR]) and a dropped rate of 4.34% (brake-specific energy consumption [BSEC]), 33.33% (carbon monoxide [CO]), 39.28% (hydrocarbons [HC]), 9.43% (smoke), and 6.97% (combustion duration [CD]) related to diesel fuel at peak load. However, single-fuel powered diesel engines provide minimal performance for the WFOB40D60 fuel blend with (11.32% lower BTE and 2.04% higher BSEC) and minimal rate of combustion (lower cylinder pressure, 2.12% minimal CD, 14.72% higher ID, minimal HRR combustion, volumetric efficiency, and MFB). Emitted fewer emissions (9.09% less CO, 4.87% less HC, 0.92% higher NO_x, and 1.69% more smoke) than diesel fuel at peak load. Therefore, it was concluded that adding 10 LPM of hydrogen gas to the biodiesel under a dual-fuel condition leads to better combustion, better performance, and less pollution than the single-fuel mode of operation.     

Performance and emission characteristics of a Kirloskar HA394 diesel engine operated on fish oil methyl esters

The high viscosity of fish oil leads to problem in pumping and spray characteristics. The inefficient mixing of fish oil with air leads to incomplete combustion. The best way to use fish oil as fuel in compression ignition (CI) engines is to convert it into biodiesel. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. Combustion tests for methyl ester of fish oil and its blends with diesel fuel were performed in a kirloskar H394 DI diesel engine, to evaluate fish biodiesel as an alternative fuel for diesel engine, at constant speed of 1500 rpm under variable load conditions. The tests showed no major deviations in diesel engine's combustion as well as no significant changes in the engine performance and reduction of main noxious emissions with the exception on NO_x. Overall fish biodiesel showed good combustion properties and environmental benefits.     

Effect of pilot fuel injection pressure and injection timing on combustion,performance and emission of hydrogen-biodiesel dual fuel engine

The present study highlights the influence of fuel injection pressure (FIP) and fuel injection timing (FIT) of Jatropha biodiesel as pilot fuel on the performance, combustion and emission of a hydrogen dual fuel engine. The hydrogen flow rates used in this study are 5lit/min, 7lit/min, and 9lit/min. The pilot fuel is injected at three FIPs (500, 1000, and 1500 bar) and at three FITs (5°, 11°, and 17?bTDC). The results showed an increase in brake thermal efficiency (B_th)from 25.02% for base diesel operation to 32.15% for hydrogen-biodiesel dual fuel operation with 9lit/min flow rate at a FIP of 1500 bar and a FITof17?bTDC. The cylinder pressure and heat release rate (HRR) are also found to be higher for higher FIPs. Advancement in FIT is found to promote superior HRR for hydrogen dual fuel operations. The unburned hydrocarbon (UHC) and soot emissions are found to reduce by 59.52% and 46.15%, respectively, for hydrogen dual fuel operation with 9lit/min flow rate at a FIP of 1500 bar and a FIT of 11?bTDC. However, it is also observed that the oxides of nitrogen (NO_X) emissions are increased by 20.61% with 9lit/min hydrogen flow rate at a FIP of 1500 bar and a FIT of 17?bTDC. Thus, this study has shown the potential of higher FIP and FIT in improving the performance, combustion and emission of a hydrogen dual fuel engine with Jatropha biodiesel as pilot fuel.