Organic field-effect transistors based on low-temperature processable transparent polymer dielectrics with low leakage current

A solution-based transparent polymer was investigated as the gate dielectric for organic field-effect transistors (OFETs). Organic thin films (400 nm) are readily fabricated by spin-coating a polyhydrazide solution under ambient conditions on the ITO substrates, followed by annealing at a low temperature (120 °C). The smooth transparent dielectrics exhibited excellent insulating properties with very low leakage current densities of ～10^?8 A/cm². High performance OFETs with evaporated pentacene as organic semiconductor function at a low operate voltage (?15 V). The mobility could reach as high as 0.7 cm²/Vs and on/off current ratio up to 10⁴. Solution-processed TIPS-pentacene OFETs also work well with this polymer dielectric.     

Organic field-effect transistors based on J-aggregate thin films of a bisazomethine dye

We report on the fabrication and the characterization of p-type organic field-effect transistors based on vapor-deposited J-aggregate bisazomethine dye thin films. The absorption spectra of this non-ionic organic semiconductor in the solid state show a strong influence of the film thickness on the J-aggregate formation. However, the electrical characteristics of the devices demonstrate that the hole transport properties do not vary significantly in films thicker than 100 nm. This is due to the fact that the J-aggregates are formed in this material at the surface of the crystalline grains and do not influence the semiconductor/gate dielectric interface and the charge transport properties of the devices. Hole field-effect mobilities as high as 2.4 × 10^?4 cm² V^?1 s^?1 were obtained and could be slightly improved by a solvent vapor treatment due to changes in the film crystallinity. Overall, this study demonstrates that J-aggregate bisazomethine dye thin films are good candidates for the realization of organic electronic devices.     

Characteristics of tetracene-based field-effect transistors on pretreated surfaces

Tetracene-based organic thin-film transistors (OTFTs) were prepared using a neutral cluster beam deposition (NCBD) method. The effect of surface modification with an amphiphilic surfactant, octadecyltrichlorosilane (OTS), on the formation of thin films and the geometric influence of channel length and width on the transistor characteristics were systematically examined. The estimated trap density and temperature-dependence of the field-effect mobility in the range of 10–300 K demonstrated that surfactant pretreatment decreased the total trap density and activation energy for hole-transport by reducing structural disorder in the active layer. In particular, the room-temperature hole mobilities of 0.162 and 0.252 cm²/Vs for untreated and OTS-pretreated devices were among the best to date for polycrystalline tetracene-based transistors using SiO₂ gate dielectric layers without any thermal post-treatment.     

High performance top-gate field-effect transistors based on poly(3-alkylthiophenes) with different alkyl chain lengths

The device characteristics of top-gate field-effect transistors (FETs) based on typical polymer semiconductor regioregular poly(3-alkylthiophenes) (P3ATs) with different alkyl chain lengths are investigated. High field-effect mobilities of ∼10⁻² cm²/Vs are obtained irrespective of alkyl chain length even when polymer gate insulators with different dielectric constants (2.1–3.9) are used. This is attributed to the spontaneous formation of highly ordered edge-on lamellar structures at the surface of P3AT thin films that are the channel regions in top-gate FETs. In addition, top-gate P3AT FETs containing different gate insulators exhibit high operational stability, with low threshold voltage shifts of <0.5 V following prolonged gate bias stress, which is comparable to that of hydrogenated amorphous silicon thin film transistors.     

Flexible,plastic transistor-based chemical sensors

Flexible, plastic chemical sensors were fabricated using a thin polymer gate dielectric layer and polymer electrodes patterned via selective wetting directly on the surface of the organic semiconductor film. Low-voltage transistors based on DDFTTF with PEDOT:PSS electrodes had a mobility as high as 0.05 cm²/Vs with an on–off ratio of 1.2 × 10⁴ on ITO/PET substrates. These devices demonstrated stable operation in water with sensor characteristics similar to those reported on rigid silicon substrates, with sub-ppm detection for cysteine and 2,4,6-trinitrobenzene (TNB).     

Wet-processed n-type OTFTs utilizing highly-stable colloids of a perylene diimide derivative

Here we propose and demonstrate a new approach to wet-processed organic thin-film transistors utilizing highly-stable colloids of small molecular organic semiconductors prepared by laser ablation technique. Highly stable N,N′-ditridecyl-3,4,9,10-perylenetetracarboxylic diimide (PTCDI-C13) colloids of 0.1 wt% concentration were prepared successfully by laser ablation technique in acetonitrile. Mean particle size of the prepared PTCDI-C13 colloid measured by dynamic light scattering method was smaller than 50 nm which is also confirmed by a transmission electron microscope observation. By simple drop-casting of prepared PTCDI-C13 colloids, typical n-type OTFTs with good saturation properties were fabricated successfully. The highest electron mobility was 1.1 × 10^?3 cm²/Vs and increased up to 0.027 cm²/Vs by post-annealing treatment.     

Complementary-like inverters based on an ambipolar solution-processed molecular bis(naphthalene diimide)-dithienopyrrole derivative

We report on high-mobility top-gate organic field-effect transistors (OFETs) and complementary-like inverters fabricated with a solution-processed molecular bis(naphthalene diimide)-dithienopyrrole derivative as the channel semiconductor and a CYTOP/Al₂O₃ bilayer as the gate dielectric. The OFETs showed ambipolar behavior with average electron and hole mobility values of 1.2 and 0.01 cm² V^?1 s^?1, respectively. Complementary-like inverters fabricated with two ambipolar OFETs showed hysteresis-free voltage transfer characteristics with negligible variations of switching threshold voltages and yielded very high DC gain values of more than 90 V/V (up to 122 V/V) at a supply voltage of 25 V.     

Improved performance in n-channel organic thin film transistors by nanoscale interface modification

We demonstrate that the electrical properties of n-channel thin film transistors can be enhanced by inserting a nanoscale interfacial layer, namely, cesium carbonate (Cs₂CO₃), between organic semiconductor and source/drain electrodes. Devices with the Cs₂CO₃/Al electrode showed a reduction of contact resistance, not only with respect to Al, but also compared to Ca. The improvement is attributed to the reduction in the energy barrier of electron injection and the prevention of unfavorable chemical interaction between the organic layer and the metal electrode. High field-effect mobility of 0.045 cm²/V s and on/off current ratios of 10⁶ were obtained in the [6,6]-phenyl C60 butyric acid methyl ester-based organic thin film transistors using the Cs₂CO₃/Al electrodes at a gate bias of 40 V.     

Improved pentacene device characteristics with sol–gel SiO2 dielectric films

The interfacial interactions between semiconductors and gate dielectrics have a profound influence on the device characteristics of field effect transistors (FETs). This paper reports on the concept of introducing a sol–gel SiO₂ as inorganic capping layer to significantly improve device characteristics of pentacene-based FETs. The smoother film surfaces of sol–gel SiO₂ (1.9 Å root-mean-square) induced larger pentacene grain sizes, and led to hole mobilities of 1.43 cm²/Vs, on–off ratio of 10⁷, and a subthreshold swing of 102 mV/decade when operating at −20 V.     

Low power flexible organic thin film transistors with amorphous Ba0.7Sr0.3TiO3 gate dielectric grown by pulsed laser deposition at low temperature

We deposited amorphous Ba_0.7Sr_0.3TiO₃ (BST) on silicon and plastic substrate under 110 °C by pulsed laser deposition (PLD) and use it as the dielectric of the organic transistor. Depends on the thickness of BST layer, the highest mobility of the devices can achieve 1.24 cm² V^?1 s^?1 and 1.01 cm² V^?1 s^?1 on the silicon and polyethylene naphthalate (PEN) substrate, respectively. We also studied the upward and downward bending tests on the transistors and the dielectric thin films. We found that the BST dielectric pentacene transistor can maintain the mobility at 0.5 cm² V^?1 s^?1 or higher while the bending radius is around 3 mm in both upward and downward bending. Our finding demonstrates the potential application of PLD growth high-k dielectric in the large area organic electronics devices.     

High-speed organic single-crystal transistors gated with short-channel air gaps: Efficient hole and electron injection in organic semiconductor crystals

Short-channel, high-mobility organic filed-effect transistors (OFETs) are developed based on single crystals gated with short-channel air gaps. The high hole mobility of 10 cm²/Vs for rubrene, and high electron mobility of 4 cm²/Vs for PDIF-CN₂ crystals are demonstrated even with a short channel length of 6 μm. Such performance is due to low contact resistance in these devices estimated to be as low as ～0.5 kΩ cm at gate voltage of ?4 V for rubrene. With the benefit of the short channel length of 4.5 μm in a new device architecture with less parasitic capacitance, the cutoff frequency of the rubrene air–gap device was estimated to be as high as 25 MHz for drain voltage of ?15 V, which is the fastest reported for p-type OFETs, operating in ambient conditions.     

High performance top contact fused thiophene–diketopyrrolopyrrole copolymer transistors using a photolithographic metal lift-off process

High-performance fused thiophene–diketopyrrolopyrrole copolymer (PTDPPTFT4) top-contact transistors have been fabricated using a top contact metal lift-off process. The source–drain (S/D) top metal contacts were directly formed by i-line photolithographic patterning over the organic semiconductor channel through a lift-off method based on a negative tone photoresist. With a fluorinated imaging material (Orthogonal OScR 2312), devices exhibit field effect mobilities up to 2.56 cm² V⁻¹ s⁻¹ and on/off ratio >10⁷, with channel lengths precisely patterned down to 10 μm. Devices prepared from the lift-off process through a commercial negative tone photoresist such as AZ nLOF 2020 instead of the fluorinated photoresist exhibited considerable degradation. De-ionized (DI) water, aqueous tetramethyl ammonium hydroxide (TMAH) developer and organic stripper do not apparently degrade the performance of the PTDPPTFT4 transistors upon dip testing. Indeed the observed degradation originates from the incomplete development of the unexposed photoresist in the TMAH developer. This is detrimental to the PTDPPTFT4 channel due to formation of resist residue over the organic semiconductor surface. This residue eventually leads to a significant increase of the S/D contact resistance upon metal contact deposition.     

Scaling down of organic complementary logic gates for compact logic on foil

In this work, we realize complementary circuits with organic p-type and n-type transistor integrated on polyethylene naphthalate (PEN) foil. We employ evaporated p-type and n-type organic semiconductors spaced side by side in bottom-contact bottom-gate coplanar structures with channel lengths of 5 μm. The area density is 0.08 mm² per complementary logic gate. Both p-type and n-type transistors show mobilities >0.1 cm²/V s with V_on close to zero volt. Small circuits like inverters and 19-stage ring oscillators (RO) are fabricated to study the static and the dynamic performance of the logic inverter gate. The circuits operate at V_dd as low as 2.5 V and the inverter stage delay at V_dd = 10 V is as low as 2 μs. Finally, an 8 bit organic complementary transponder chip with data rate up to 2.7 k bits/s is fabricated on foil by successfully integrating 358 transistors.     

Organic thin-film transistors with bilayer of rubbed and evaporated hydrocarbon-based acene as active layer

We have investigated organic thin-film transistors (OTFTs) with a bilayer of rubbed and evaporated hydrocarbon-based acene 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT) as an active layer. Using a rubbing process after spin-coating the C8-BTBT, crystallinity of the C8-BTBT thin film was improved and resultant superior OTFT characteristics were realized. We obtained a field-effect mobility of 1.6 cm²/Vs, a threshold voltage of −8.2 V, an on-off ratio of 10⁶, and a subthreshold swing of 55 mV/decade.     

Integration of a graphene ink as gate electrode for printed organic complementary thin-film transistors

We demonstrate a new electrode gate based on graphene ink for complementary printed organic metal oxide semiconductor (CMOS) technology on flexible plastic substrates. The goal is to replace the standard silver electrode gate. Devices made with graphene were enhanced and showed a high field-effect mobility of 3 cm² V⁻¹ s⁻¹ for P-type and 0.9 cm² V⁻¹ s⁻¹ for the N-type semiconductors. The improvement is attributed to the increase of the electrical capacitance of the organic dielectric (CYTOP) due to the graphene layer. A seven-stage ring oscillator was made with high oscillation frequencies of 2.1 kHz at 40 V corresponding to a delay/gate value of 34 μs. These performances are promising for use of low cost printed electronic applications.     

Solution processable poly(2,5-dialkyl-2,5-dihydro-3,6-di-2-thienyl-pyrrolo[3,4-c]pyrrole-1,4-dione) for ambipolar organic thin film transistors

Solution processable diketopyrrolopyrrole (DPP)-bithiophene polymers (PDBT) with long branched alkyl side chains on the DPP unit are synthesized. These polymers have favourable highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels for the injection and transport of both holes and electrons. Organic thin film transistors (OTFTs) using these polymers as semiconductors and gold as source/drain electrodes show typical ambipolar characteristics with very well balanced high hole and electron mobilities (μ_h = 0.024 cm² V^?1 s^?1 and μ_e = 0.056 cm² V^?1 s^?1). These simple and high-performing polymers are promising materials for ambipolar organic thin film transistors for low-cost CMOS-like logic circuits.     

In0.75Ga0.25As channel layers with record mobility exceeding 12,000 cm2/Vs for use in high-κ dielectric NMOSFETs

In_0.75Ga_0.25As channel layers with a record mobility exceeding 12,000 cm²/Vs for use in high-κ dielectric NMOSFETs have been fabricated. The device structures which have been grown by molecular beam epitaxy on 3″ semi-insulating InP substrate comprise a 10 nm strained In_0.75Ga_0.25As channel layer and a high-κ oxide based dielectric layer (κ ≅ 20). Electron mobilities of 12,033 and 7,042 cm²/Vs have been measured for sheet carrier concentrations n_s of 2.5 × 10¹² and 6 × 10¹² cm⁻², respectively.     

High performance organic thin film transistors using chemically modified bottom contacts and dielectric surfaces

A compatible process of orthogonal self-assembled monolayers (SAMs) is applied to intentionally modify the bottom contacts and gate dielectric surfaces of organic thin film transistors (OTFTs). This efficient interface modification is first achieved by 4-fluorothiophenol (4-FTP) SAM to chemically treat the silver source–drain (S/D) contacts while the silicon oxide (SiO₂) dielectric interface is further primed by either hexamethyldisilazane (HMDS) or octyltrichlorosilane (OTS-C8). Results show that the field effect mobilities of the bottom-gate bottom-contact PTDPPTFT4 transistors were significantly improved to 0.91 cm² V⁻¹ s⁻¹.     

n-Type self-assembled monolayer field-effect transistors for flexible organic electronics

Within this work we present n-type self-assembled monolayer field-effect transistors (SAMFETs) based on a novel perylene bisimide. The molecule spontaneously forms a covalently fixed monolayer on top of an aluminium oxide dielectric via a phosphonic acid anchor group. Detailed studies revealed an amorphous, two-dimensional semiconducting sheet on top of the dielectric. Reliable transistors with electron mobilities on the order of 10^?3 cm²/V s with limited hysteresis were achieved on rigid as well on flexible substrates. Furthermore, a flexible NMOS-bias inverter based on SAMFETs is demonstrated for the first time.     

Improving solution-processed n-type organic field-effect transistors by transfer-printed metal/semiconductor and semiconductor/semiconductor heterojunctions

Solution-processed n-type organic field effect transistors (OFETs) are in need of proper metal contact for improving injection and mobility, as well as balanced hole mobility for building logic circuit units. We address the two distinct problems by a simple technique of transfer-printing. Transfer-printed Au contacts on a terrylene-based semiconductor (TDI) significantly reduced the inverse subthreshold slope by 5.6 V/dec and enhanced the linear mobility by over 5 times compared to evaporated Au contacts. Hence, devices with a high-work-function metal (Au) are comparable with those with low-work-function metals (Al and Ca), indicating a fundamental advantage of transfer-printed electrodes in electron injection. We also transfer-printed a poly(3-hexylthiophene) (P3HT) layer onto TDI to construct a double-channel ambipolar transistor by a solution process for the first time. The transistor exhibits balanced hole and electron mobility (3.0 × 10⁻³ and 2.8 × 10⁻³ cm² V⁻¹ s⁻¹) even in a coplanar structure with symmetric Au electrodes. The technique is especially useful for reaching intrinsic mobility of new materials, and enables significant enlargement of the material tanks for solution-processed functional heterojunction OFETs.