共查询到20条相似文献,搜索用时 234 毫秒
1.
200MW机组热态启动问题分析与两班制调峰运行方式的探讨 总被引:1,自引:0,他引:1
本文分析了河北南网200MW机组多次热态启动中发现的主要问题,作为改进热态启动的参考,同时从分析中看出200MW机组适应两班制调峰的困难以及被迫进行两班制调峰给安全运行带来的不利影响。基于此,本文对200MW机组两班制调峰的运行方式作了探讨,提出了新的运行方式即低速运行方式来实现两班制调峰的建议,并进一步探讨了低速运行的可行方案,分析了低速运行两班制调峰的安全性和经济性,作出了优于停机方式的初步结论。 相似文献
2.
随着电网容量的不断增大,大容量机组参与调峰已是一个现实问题,国内已有一部分200 MW以上的火力发电机组参与调峰工作。但大机组适应调峰工作的情况也不尽相同。目前运行的200 MW机组,一般情况最多只能调到70%负荷,再往下调就比较困难。就锅炉燃烧本身而言,低于70%负荷燃烧不稳定,而且热工控制系统基本也是按 相似文献
3.
河北省马头电厂地处该省南网,火电容量1566MW,水电容量75MW,全网总容量1641MW,最大可调出力1300MW。近几年,随着电网容量日益增大,每年峰谷差逐年增大,小机组起停已不适应调峰要求,因此马头电厂三台200MW机组必然要参与调峰。为了掌握大机组调峰运行特性,以便推广使用,水电部科技司给西安热工所下达国产200MW机组调峰试验任务。1984年首先在国产100MW机组上进行调峰试验,取得了较理想的结果。在此基础上,又于1985年第四季度到1988年初,由马头电厂、西安热工所、河北省电力试验研究所、浙江省电力试验研究所共同协作,在国产200MW机组上进行调峰试验。试验表明,锅炉在断油条件下燃用贫煤,使用四个煤粉预燃室,可以较长时间稳定在100MW负荷下运行,机组调节负荷幅度较大,运行性能比较好。通过试验,证实该机组可以适应中间变动负荷,能够满足电网调峰需要。这次试验的成功将为华北电网大机组调峰及电站的节能开辟途径,也为今后设计电站调峰机组提供技术依据。 相似文献
4.
一、前言随着电网容量的不断增大和用电结构的变化,大型机组参与电网调峰已势在必行。目前运行的国产大机组(200MW、300MW)均是按带基本负荷设计的。为了探讨该类机组的调峰能力及存在问题,不少单位做过许多的试验与研究,我们参与了马头电厂~#3、~#7机组的调峰试验工作,本文就上述两炉的试验结果及有关问题进行粗浅地分析。 相似文献
5.
6.
7.
8.
本文通过对调峰汽轮机组的理论分析,提出了调峰汽比机组的最佳经济运行方式,并以200MW调峰机组为例,论证并说明了其最佳运行工况. 相似文献
9.
针对吉林热电厂200MW机组的调峰经济性试验进行了计算及分析,指出汽轮机组在160MW至120MW负荷区间采用滑压运行方式的经济性优于定压运行,可降低热耗率1.03%~1.26%,为省内大型火电机组的调峰经济运行提供了参考数据。 相似文献
10.
由于四川电网容量日益增大,用100MW机组调峰已不能满足要求,需要用200MW或更大的机组调峰。是用法国机组330MW调峰,还是用国产200MW机组调峰,应该对这两种机组的调峰能力、调峰机动性、参加调峰后可能出现的事故率以及机组寿命消耗等问题进行初步分析。 相似文献
11.
12.
13.
Yuan Chen Westergard L. Mojarradi M.M. Johnson T.W. Cozy R.S. Billman C. Burke G.R. Kolawa E.A. 《Device and Materials Reliability, IEEE Transactions on》2006,6(2):146-153
A design for reliability methodology has been developed for electronics for low-temperature applications. A hot carrier aging (HCA) lifetime projection model is proposed to take into account the HCA impact on technology, analysis of parametric degradation versus critical circuit path degradation, transistor bias profile, transistor substrate current profile, and operating temperature profile. The most applicable transistor size can be determined in order to meet the reliability requirements of the electronics operating under low temperatures. This methodology and approach can also be applied to other transistor-level failure and/or degradation mechanisms for applications with varying temperature ranges. 相似文献
14.
15.
《Power Delivery, IEEE Transactions on》1998,13(1):73-77
IEEE Standard 1344, Synchrophasors for Power Systems, was completed in 1995. It sets parameters required to ensure that phasor measurement will be made and communicated in a consistent manner. It specifies requirements for the timing signal used for phasor synchronization and the time code needed for input to a measurement unit. GPS is the recommended time source and IRIG-B is the basic format used for time communication. The standard requires correlating phasors computed from unsynchronized and synchronized sampling to a common basis. Timetagging accurately and consistently is essential for wide area comparison of phase. The standard specifies information exchange and control message formats. These include data output, configuration, and command messages. It includes 7 annexes that discuss the concepts covered in the body of the standard 相似文献
16.
17.
18.
19.
20.
分析了GIS断路器故障原因,介绍了检验过程与充气检查、监督情况,并提供一些可借鉴的成功经验。 相似文献