碱性水钠锰矿氧化Cr(Ⅲ)的影响因素研究

采用氧化还原法合成3个不同氧化度的碱性水钠锰矿,并表征其晶体结构、比表面积和表面化学性质,探讨其对Cr(Ⅲ)的氧化及影响因素。研究表明:随着合成反应的n(Mn7+)/n(Mn2+)逐渐减小,合成碱性水钠锰矿的氧化度和比表面积逐渐减小,其PZC逐渐升高。反应时间和反应条件(p H、Cr(Ⅲ)浓度和矿物用量)均影响碱性水钠锰矿对Cr(Ⅲ)的氧化。在低p H值范围内Cr(Ⅲ)氧化率随着p H的增加逐渐增加,但在高p H值范围内氧化率随着p H的升高而减小。此外,Cr(Ⅲ)的氧化率随着Cr(Ⅲ)浓度的升高逐渐降低,但随着氧化度的提高显著增加。     

不同结构水钠锰矿催化氧化对苯二酚腐殖化程度的差异及其原因分析

本文合成了一系列不同氧化度的酸性和碱性水钠锰矿,以对苯二酚作为腐殖质形成的前驱物,分析水钠锰矿矿物类型和亚结构变化对对苯二酚腐殖化程度的影响。取得的主要结果有:水钠锰矿的矿物类型和亚结构(锰氧化度、八面体空位、H+、Mn4+和Mn3+含量)对对苯二酚的腐殖化程度具有重要的影响,且矿物类型的影响大于同种矿物不同亚结构产生的影响。酸性水钠锰矿比碱性水钠锰矿含有更多的H+,导致酸性水钠锰矿比碱性水钠锰矿具有更高的氧化容量,反应达到平衡后,对苯二酚腐殖化程度更高。因此,水钠锰矿物中H+含量对对苯二酚腐殖化程度的影响要大于矿物中Mn4+和Mn3+含量的影响。同种类型水钠锰矿氧化度越高,得电子量将越多,氧化容量越大,反应达到平衡后,对苯二酚腐殖化程度越高。     

模拟环境条件下δ-MnO_2氧化As(Ⅲ)的搅拌流动动力学特征

采用搅拌流动法研究了酸性水钠锰矿及水羟锰矿2种δ-MnO2矿物氧化As(Ⅲ)的动力学过程,构建了可用于多相体系的搅拌-流动氧化还原反应动力学模型.经过As吸附量的校正后,该模型对酸性水钠锰矿及水羟锰矿氧化As(Ⅲ)动力学数据拟合度分别为0.980和0.951,模型拟合得到pH 7时2种矿物单位比表面上氧化As(Ⅲ)的初始反应速率常数k分别为0.131,0.014min-1·m-2.相比而言,该速率常数明显高于批量法得到的表观速率常数kobs,0.021,0.001min-1?m-2更接近真实的化学动力学参数.搅拌流动法与批量法得到的不同矿物的速率常数大小趋势一致,即尽管酸性水钠锰矿对As(Ⅲ)的氧化率低于水羟锰矿,单位比表面上酸性水钠锰矿氧化As(Ⅲ)初始反应速率却远高于水羟锰矿.反应过程分析表明,反应初始阶段,As(Ⅲ)的吸附为主要限速步骤;而随着反应的进行,矿物表面反应位点逐渐钝化或减少,反应位点数量成为限速步骤.     

模拟环境条件下δ-MnO2氧化As(III)的搅拌流动动力学特征

采用搅拌流动法研究了酸性水钠锰矿及水羟锰矿2种δ-MnO2矿物氧化As(Ⅲ)的动力学过程,构建了可用于多相体系的搅拌-流动氧化还原反应动力学模型.经过As吸附量的校正后,该模型对酸性水钠锰矿及水羟锰矿氧化As(III)动力学数据拟合度分别为0.980和0.951,模型拟合得到pH 7时2种矿物单位比表面上氧化As(III)的初始反应速率常数k分别为0.131,0.014min-1×m-2.相比而言,该速率常数明显高于批量法得到的表观速率常数kobs,0.021,0.001min-1×m-2更接近真实的化学动力学参数.搅拌流动法与批量法得到的不同矿物的速率常数大小趋势一致,即尽管酸性水钠锰矿对As(III)的氧化率低于水羟锰矿,单位比表面上酸性水钠锰矿氧化As(III)初始反应速率却远高于水羟锰矿.反应过程分析表明,反应初始阶段,As(III)的吸附为主要限速步骤;而随着反应的进行,矿物表面反应位点逐渐钝化或减少,反应位点数量成为限速步骤.     

纳米零价铁铜双金属对铬污染土壤中Cr(Ⅵ)的还原动力学

采用液相还原法制备纳米零价铁铜双金属(n ZVI/Cu),通过扫描电子显微镜(SEM)和X射线衍射(XRD)对其进行形貌观测和表征分析,用制备的n ZVI/Cu修复Cr(Ⅵ)污染的土壤,研究了不同反应条件对修复效果的影响,探讨了还原动力学规律.结果表明,n ZVI/Cu对土壤中的Cr(Ⅵ)有很好的降解效果,反应初始p H为7,温度为30℃时,加入2 g·L~(-1)的n ZVI/Cu材料,在10 min内Cr(Ⅵ)含量为88 mg·kg~(-1)的污染土壤中的Cr(Ⅵ)去除率可以达到99%以上.改变n ZVI/Cu加入量、p H值、反应温度以及添加腐殖酸都会对Cr(Ⅵ)的去除效果产生影响.改变p H值和反应温度对去除土壤中Cr(Ⅵ)的影响都比较明显,p H值越小,反应温度越高Cr(Ⅵ)的去除效果越好,添加腐殖酸对去除土壤中的Cr(Ⅵ)有一定的影响.n ZVI/Cu降解Cr(Ⅵ)的过程符合伪一级还原动力学模型,还原速率与反应温度的关系符合阿仑尼乌斯(Arrhenius)定律,反应活化能Ea为104.26 k J·mol~(-1).     

纳米复合水凝胶的制备及其对重金属离子的吸附

以N-羟甲基丙烯酰胺(HMAm)和2-丙烯酸羟乙酯(HEA)为共聚单体,采用60Co-γ射线低温辐照法,制备了具酰胺基和羟基的新型聚合物水凝胶p(HMAm/HEA),运用原位沉淀法制备了纳米复合水凝胶HMO-p(HMAm/HEA),用于对重金属离子Pb~(2+)和Cu~(2+)的去除.应用SEM、TEM、FTIR等方法对水凝胶进行表征,表征结果证明p(HMAm/HEA)是HMAm和HEA的共聚产物,且纳米水合氧化锰(HMO)成功负载.探讨了溶液初始p H值、反应温度、重金属初始浓度、反应时间、竞争性Ca~(2+)和Na+浓度等因素对纳米复合水凝胶吸附过程的影响,研究表明HMO-p(HMAm/HEA)对Pb~(2+)和Cu~(2+)的吸附过程不受温度的影响;吸附量随着溶液初始p H的升高而增加;吸附过程属于Langmuir单分子层吸附;吸附动力学过程符合准二级动力学吸附;高浓度的Ca~(2+)和Na~+对吸附过程影响不大.XPS图谱进一步证明吸附机制是重金属离子与羟基间的离子交换作用.采用0.05 mol·L~(-1)的HCl溶液为脱附剂,经过4次吸附-脱附循环再生后,纳米复合水凝胶重复利用性好.     

磷酸钙沉淀法同步去除污泥水中磷和腐殖质的优化研究

以含有腐殖质(HS)的含磷污水为处理对象,开展了磷酸钙结晶同步去除磷和HS的优化研究.通过响应面法考察了HS浓度、p H和Ca/P摩尔比(Ca/P)对正磷和HS去除效果的单独和联合效应,利用X射线衍射表征固体产物.结果表明,磷酸钙结晶法可同步去除磷和HS,HS的存在降低了除磷效率.p H对磷去除率有显著性影响,而Ca/P和HS浓度对HS去除率有显著性影响.三因素联合效应中Ca/P和HS浓度联合效应对HS去除率有显著性影响.提高反应p H有助于减小HS对磷酸钙除磷的影响,固体产物结晶度增强,但固体纯度降低.     

纳米零价铁及其双金属体系对菲的降解研究

以实验室合成的纳米零价铁(n ZVI)及其双金属(n ZVI/Cu和n ZVI/Ni)为反应材料,对菲(Phenanthrene)的去除进行研究.表征结果表明:纳米颗粒平均粒径均为80~100 nm,主要以α-Fe0的形式存在.批实验结果表明,5 g·L-1的n ZVI,n ZVI/Cu和n ZVI/Ni对菲溶液均有去除效果,其去除效率依次为n ZVI/Nin ZVI/Cun ZVI.溶液初始p H为7.5时,5 g·L-1的n ZVI/Ni去除88%0.5 mg·L-1的菲只需3 h,而n ZVI/Cu和n ZVI分别需要29 h和40 h.3种纳米铁对菲的去除率均随着n ZVI投加量的增加而升高,随着菲溶液初始浓度的增加而降低.反应温度的升高可提高n ZVI/Ni对菲的去除效率,高温时(≥30℃)菲的降解遵循一级反应动力学模型.p H对反应影响不大.GC-MS结果表明,n ZVI/Ni降解菲溶液主要为催化加氢反应,而n ZVI/Cu和n ZVI对菲溶液的去除主要为吸附作用.     

秸秆生物炭对有机染料的吸附作用及机制

研究了裂解温度分别为500℃和700℃的两种水稻秸秆生物炭(分别标记为W500、W700)对有机染料日落黄和亚甲基蓝的吸附作用及机制.同时,针对实际印染废水的特点,考察了反应温度、p H和硫酸盐对吸附去除效率的影响.结果显示,生物炭对两种染料的吸附均符合准二级动力学方程,等温吸附曲线均可用Freundlich模型较好地描述,但其对两种染料的吸附机制显著不同.生物炭对阳离子染料亚甲基蓝的吸附主要通过离子交换作用,随着生物炭裂解温度升高,其极性基团减少,离子交换作用减弱.生物炭对阴离子染料日落黄的吸附则主要通过生物炭芳香结构与日落黄分子芳环之间的π-π相互作用,随裂解温度升高,生物炭芳香化程度增大,π-π作用随之增大;生物炭对两种染料的吸附去除效率均随反应温度的升高(5~45℃)而增大,且在3p H11、硫酸盐浓度25~2500 mg·L~(-1)的变化范围内,吸附去除效率均保持稳定.     

凹凸棒石@C纳米复合材料对Cr(Ⅵ)吸附-还原作用

以凹凸棒石和葡萄糖为原料,通过设置凹凸棒石与葡萄糖不同质量比,采用水热碳化法制备凹凸棒石@C纳米复合材料,并选择出去除Cr(Ⅵ)效果最佳的凹凸棒石@C纳米复合材料.同时,利用傅里叶红外光谱(FT-IR)、X射线衍射(XRD)、Zeta电位仪(Zeta)、X光电子能谱(XPS)手段对复合材料进行了表征,考察了时间和p H对其去除水中Cr(Ⅵ)的影响,探讨了其吸附-还原机制.结果表明,最佳复合材料的凹凸棒石与葡萄糖质量比为1∶4;吸附平衡时间约为6 h,动力学过程符合准二级动力学模型.在p H为1~10时,Cr(Ⅵ)去除率随p H升高而减小,p H=1时Cr(Ⅵ)去除率最大,高达92.7%,吸附率为48.5%,还原率为44.2%;而总铬吸附率则随p H升高先增大后减小,p H=2时最大,吸附率为50.2%,还原率为13.0%,表明对Cr(Ⅵ)去除存在吸附-还原作用,酸性越强,越容易发生还原反应.FT-IR分析结果表明,凹凸棒石@C纳米复合材料表面存在含氧基团和还原性基团(Cx—OH、—CH等);XPS分析结果表明其对Cr(Ⅵ)的去除是吸附-还原相互作用的结果,包括Cr(Ⅵ)在复合材料表面与含氧基团络合配位吸附和静电吸附,以及Cr(Ⅵ)还原Cr(Ⅲ)再吸附,其中,Cr(Ⅲ)再吸附主要通过与Mg2+、Al3+等阳离子交换作用实现的.     

改性石墨烯对水中亚甲基蓝的吸附性能研究

对十六烷基三甲基溴化铵(CTAB)改性石墨烯用于水中亚甲基蓝(MB)的去除进行了研究.用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射分析仪(XRD)、傅里叶红外光谱分析仪(FTIR)和热重分析仪(TGA)对石墨烯和改性石墨烯性能进行表征.探讨了反应时间、pH、温度、剂量对石墨烯和改性石墨烯去除MB的影响.结果表明,在石墨烯制备过程中添加CTAB可以明显增大比表面积,提高MB的去除率.反应过程在前15 min内反应速率很快,并约在120 min内达到吸附平衡.吸附动力学符合伪二级动力学模型.最佳反应温度为293 K,吸附剂投加量的最适浓度为2 g·L-1,且吸附量的大小与溶液的初始pH值无关.通过Langmuir等温吸附方程得到改性石墨烯的最大吸附量86.43 mg·g-1,且为放热反应.     

Response surface methodology analysis of the photocatalytic removal of Methylene Blue using bismuth vanadate prepared via polyol route

Visible-light driven photocatalyst bismuth vanadate (BiVO₄) photocatalyst was synthesized by the polyol route using ethylene glycol. The precipitate was washed, dried and calcined at 450℃ for 3 hr. The sample was characterized by X-ray diffractometry (XRD), field emission scanning electron microscopy (FE-SEM), zeta potential, surface area (BET method) and band gap energy via diffuse reflectance spectroscopy (DRS). The synthesized BiVO₄ has a monoclinic phase with a surface area of 4.3 m²/g and a band gap energy of 2.46 eV. A majority of the particles were in the range of 90-130 nm as obtained from the particle size distribution histrogram. The efficiency of the sample as a visible-light driven photocatalyst was examined by photodegrading Methylene Blue (MB). The effects of some operational photodegradation parameters such as mass loading, initial dye concentration and pH were also examined. Experimental design methodology was applied by response surface modeling and optimization of the removal of MB. The multivariate experimental design was employed to develop a quadratic model as a functional relationship between the percentage removal of MB and three experimental factors (BiVO₄ loading, MB initial concentration and pH). The percentage removal of MB approached 67.21% under optimized conditions. In addition, a satisfactory goodness-of-fit was achieved between the predictive and the experimental results.     

离子束辐照活性炭吸附性能研究

利用离子束注入机对活性炭进行N+辐照改性,使用场发射扫描电子显微镜(FESEM)、拉曼光谱仪(Raman)对活性炭表面形貌、结构等特性进行表征,研究了改性后活性炭对亚甲基蓝(MB)吸附性能的变化。实验表明:活性炭经离子束辐照后,比表面积和石墨化程度均降低,对亚甲基蓝的吸附能力降低,且辐照剂量增大,吸附能力减小。在活性炭浓度为0.667 g/L,吸附时间为360 min,振荡器频率为250 r/min,吸附温度为308 K时,活性炭对亚甲基蓝的吸附量为249.081 mg/g,改性活性炭(剂量为40 000 dose)在同等条件下吸附量为241.726 mg/g。改性活性炭对亚甲基蓝吸附过程符合Langmuir和Freundlich吸附等温模型。     

Arsenite oxidation by three types of manganese oxides

Oxidation of As（Ⅲ） by three types of manganese oxides and the effects ofpH, ion strength and tartaric acid on the oxidation were investigated by means of chemical analysis, equilibrium redox, X-ray diffraction （XRD） and transmission electron microscopy （TEM）. Three synthesized Mn oxide minerals, bimessite, cryptomelane, and hausmannite, which widely occur in soil and sediments, could actively oxidize As（Ⅲ） to As（Ⅴ）. However, their ability in As（Ⅲ）-oxidation varied greatly depending on their structure, composition and surface properties. Tunnel structured cryptomelane exhibited the highest ability of As （Ⅲ） oxidation, followed by the layer structured birnessite and the lower oxide hausmannite. The maximum amount of As （Ⅴ） produced by the oxidation was in the order （mmol/kg） of cryptomelane （824.2） 〉 bimessite （480.4） 〉 hausmannite （117.9）, As pH increased from the very low value（pH 2.5）, the amount of As（Ⅲ） oxidized by the tested Mn oxides was firstly decreased, then negatively peaked in pH 3.0 6.5, and eventually increased remarkably. Oxidation of As（Ⅲ） by the Mn oxides had a buffering effects on the pH variation in the solution. It is proposed that the oxidative reaction processes between As （Ⅲ） and biruessite（or cryptomelane） are as follows： （1） at lower pH condition： （MnO2）x＋ H3AsO3 ＋ 0.5H^＋=0.5H2AsO4^- ＋ 0.5HAsO4^2- ＋Mn〉^2＋ （MnO2）x-1 ＋ H2O; （2） at higher pH condition： （MnO2）x ＋ H3AsO3 = 0.5H2AsO4^- ＋ 0.5HAsO4^2- ＋ 1.5H^＋ ＋ （MnO2）x-1. MnO. With increase of ion strength, the As（Ⅲ） oxidized by bimessite and cryptomelane decreased and was negatively correlated with ion strength. However, ion strength had little influence on As （Ⅲ） oxidation by the hausmarmite. The presence of tartaric acid promoted oxidation of As（Ⅲ） by birnessite. As for cryptomelane and hansmannite, the same effect was observed when the concentration of tartaric acid was below 4 mmol/L, otherwise the oxidized As（Ⅲ） decreased. These findings are of great significance in improving our understanding of As geochemical cycling and controlling As contamination.     

Enhanced adsorption of Methylene Blue from aqueous solution by chitosan-g-poly （acrylic acid）/vermiculite hydrogel composites

A series of chitosan-g-poly (acrylic acid)/vermiculite hydrogel composites were synthesized and used as adsorbents for the investigation of the e ect of process parameters such as vermiculite content, pH of dye solution, contact time, initial concentration of dye solution, temperature, ionic strength and concentration of surfactant sodium dodecyl sulfate on the removal of Methylene Blue (MB) from aqueous solution. The results showed that the adsorption capacity for dye increased with increasing pH, contact time and initial dye concentration, but decreased with increasing temperature, ionic strength and sodium dodecyl sulfate concentration in the present of the surfactant. The adsorption kinetics of MB onto the hydrogel composite followed pseudo second-order kinetics and the adsorption equilibrium data obeyed Langmuir isotherm. By introducing 10 wt.% vermiculite into chitosan-g-poly (acrylic acid) polymeric network, the obtaining hydrogel composite showed the highest adsorption capacity for MB, and then could be regarded as a potential adsorbent for cationic dye removal in a wastewater treatment process.     

新型改性磷灰石水处理剂去除废水中铅离子的研究

文章对一种颗粒状废水处理剂去除水溶液中Pb2+进行了研究。考察pH值、温度、处理时间、Pb2+浓度、水处理剂的用量、比表面积及颗粒大小等因素对去除Pb2+能力的影响。研究的结果表明:水处理剂去除水溶性Pb2+的主要作用机理为溶解沉淀过程;反应速率在pH2.5～5.5范围内与pH呈负线性相关,与Pb2+浓度呈正相关关系。较低的pH值,较长的处理时间和较高的反应温度可以适当提高水处理剂去除Pb2+能力,最大可达253.2mg/L;水处理剂粒度在1～5mm之间,比较符合生产的要求。比表面积与去除Pb2+能力呈正相关关系,可作为水处理剂去除重金属离子能力强弱的重要评判标准之一。     

黄铁矿催化类Fenton反应处理阳离子红X-GRL废水

基于对天然矿物黄铁矿进行SEM、EDS表征的基础上,以黄铁矿为非均相类Fenton催化剂,以偶氮染料阳离子红X-GRL为目标污染物,考察了催化剂双氧水用量、溶液初始pH值、阳离子红X-GRL初始浓度、反应时间等因素对染料脱色效果的影响.结果表明,在H2O2浓度为26.6mg/L、矿用量1g/L、溶液初始pH值6.4左右的条件下,反应2min后,染料脱色率达95%左右.进行了黄铁矿在水溶液中的酸性氧化实验并且考察了Fe2+、SO42-浓度及溶液pH随矿重复利用次数的变化规律.初次使用的黄铁矿具有很强的酸性氧化特性,反应过程中伴随着大量Fe2+、SO42-及H+的溶出.染料的快速脱色主要是均相Fenton反应作用的结果.黄铁矿作为一种新的催化剂大大提高了类Fenton反应的催化活性,而且该新型类Fenton反应能克服传统Fenton反应适用pH范围小的局限性,拓展了Fenton反应在废水处理中的应用.     

柚子皮吸附水溶液中亚甲基蓝的机理研究

为研究柚子皮吸附水溶液中亚甲基蓝（MB）的吸附性能和吸附机理,试验考察了不同条件（如pH,生物材料粒径,染料浓度,吸附时间和温度等）对其吸附效果的影响. 结果显示:染料溶液在弱酸或碱性条件下有利于亚甲基蓝被该生物材料吸附;其粒径对吸附效果影响不大;在30 ℃的条件下,对亚甲基蓝的吸附在1 h左右达到平衡且符合二级动力学方程;在30 ℃及pH为8时的最大吸附量为169.49 mg/g,符合Langmuir方程;该吸附过程为放热反应,最大吸附量随温度的升高而减少. 表明柚子皮吸附亚甲基蓝的过程是以物理吸附为主,可作为染料废水处理材料.      

Fabrication of bimetallic Ag/Fe immobilized on modified biochar for removal of carbon tetrachloride

As an effective conventional absorbent, biochar exhibited limited adsorption ability toward small hydrophobic molecules. To enhance the adsorption capacity, a novel adsorbent was prepared by immobilizing nanoscale zero-valent iron onto modified biochar (MB) and then the elemental silver was attached to the surface of iron (Ag/Fe/MB). It''s noted that spherical Ag/Fe nanoparticles with diameter of 51 nm were highly dispersed on the surface of MB. As the typical hydrophobic contaminant, carbon tetrachloride was selected for examining the removal efficiency of the adsorbent. The removal efficiencies of carbon tetrachloride by original biochar (OB), Ag/Fe, Ag/Fe/OB and Ag/Fe/MB were fully investigated. It''s found that Ag/Fe/MB showed higher carbon tetrachloride removal efficiency, which is about 5.5 times higher than that of the OB sample due to utilizing the merits of high adsorption and reduction. Thermodynamic parameters revealed that the removal of carbon tetrachloride by Ag/Fe/MB was a spontaneous and exothermic process, which was affected by solution pH, initial carbon tetrachloride concentration and temperature. The novel Ag/Fe/MB composites provided a promising material for carbon tetrachloride removal from effluent.