Effects of electrolyte concentration and current density on the properties of electro-deposited NiFeW alloy coatings

NiWP alloy coatings were prepared by electrodeposition, and the effects of ferrous chloride (\(\hbox {FeCl}_{2})\), sodium tungstate (\(\hbox {Na}_{2}\hbox {WO}_{4})\) and current density (\(D_{\mathrm{K}}\)) on the properties of the coatings were studied. The results show that upon increasing the concentration of \(\hbox {FeCl}_{2}\), initially the Fe content of the coating increased and then tended to be stable; the deposition rate and microhardness of coating decreased when the cathodic current efficiency (\(\eta \)) initially increased and then decreased; and for a \(\hbox {FeCl}_{2}\) concentration of \(3.6\, \hbox {g\,l}^{-1}\), the cathodic current efficiency reached its maximum of 74.23%. Upon increasing the concentration of \(\hbox {Na}_{2}\hbox {WO}_{4}\), the W content and microhardness of the coatings increased; the deposition rate and the cathode current efficiency initially increased and then decreased. The cathodic current efficiency reached the maximum value of 70.33% with a \(\hbox {Na}_{2}\hbox {WO}_{4}\) concentration of 50 g \(\hbox {l}^{-1}\), whereas the deposition rate is maximum at 8.67 \(\upmu \hbox {m}\,\hbox {h}^{-1}\) with a \(\hbox {Na}_{2}\hbox {WO}_{4}\) concentration of \(40\, \hbox {g\,l}^{-1}\). Upon increasing the \(D_{\mathrm{K}}\), the deposition rate, microhardness, Fe and W content of the coatings increased, the cathodic current efficiency increases first increased and then decreased. When \(D_{\mathrm{K}}\) was 4 A dm\(^{-2}\), the current efficiency reached the maximum of 73.64%.     

Estimating the Kinematic Viscosity of Petroleum Fractions

Kinematic viscosity correlation has been developed for liquid petroleum fractions at 37.78\(\,^{\circ }\hbox {C}\) and \(98.89\,^{\circ }\hbox {C}\) (100 and \(210^{\circ }\hbox {F})\) standard temperatures using a large variety of experimental data. The only required inputs are the specific gravity and the average boiling point temperature. The accuracy of the correlation was compared with several other correlations available in the literature. The proposed correlations proved to be more accurate in predicting the viscosity at 37.78\(\,^{\circ }\hbox {C}\) and \(98.89\,^{\circ }\hbox {C}\) with average absolute deviations of 0.39 and \(0.72\hbox { mm}^{2}/\hbox {s}\), respectively. Another objective was to develop a relation for the variation of viscosity with temperature to predict the viscosity of petroleum fraction at a certain temperature from the knowledge of the viscosity for the same liquid at two other temperatures. The newly developed correlation represents a wide array of temperatures from 20 \(^{\circ }\hbox {C}\) to 150 \(^{\circ }\hbox {C}\) and viscosities from 0.14\(\hbox { mm}^{2}/\hbox {s}\) to 343.64\(\hbox { mm}^{2}/\hbox {s}\). The results have been validated with experimental data consisting of 9558 data points, yielding an overall deviation of \(0.248\hbox { mm}^{2}/\hbox {s}\) and \(\hbox {R}^{2}\) of 0.998. In addition, new formulas were developed to interconvert the viscosity of petroleum fractions from one unit of measure to another based on finding the best fit for a set of experimental data from the literature with \(R^{2}\) as high as 1.0 for many cases. Detailed analysis showed good agreement between the predicted values and the experimental data.     

Photoacoustic Study on the Structural Variation of Titania Nanomaterials Using the Pr (III) Ion as a Spectral Probe

In this work, \(\hbox {Pr}^{3+}\)-doped titania nanomaterials were prepared by a sol–gel method. The structural variations of the samples during the phase transitions were studied by using the \(\hbox {Pr}^{3+}\) ion as a photoacoustic spectral probe. The result shows that for the gel sample heated at \(80\,^{\circ }\hbox {C}\), the coordination environment of \(\hbox {Pr}^{3+}\) is similar to that of its aqueous ion. The f–f transitions of \(\hbox {Pr}^{3+}\) exhibit a continuous red shift along with the gel-to-anatase transition, indicating an increase of the ‘degree of covalency’ for the \(\hbox {Pr}^{3+}\) bonding. For the sample calcined at \(1100\,^{\circ }\hbox {C}\), however, the f–f transitions of \(\hbox {Pr}^{3+}\) show obvious blue shift. This can be attributed to the segregation of \(\hbox {Pr}^{3+}\) ions to the external surface during the anatase-to-rutile transition, forming \(\hbox {Pr}_{4}\hbox {Ti}_{9}\hbox {O}_{24}\). The stabilization effect of the doped \(\hbox {Pr}^{3+ }\)ions on the anatase phase of the samples is also discussed.     

Microwave dielectrics: solid solution,ordering and microwave dielectric properties of $$(1{-}x)\hbox {Ba}(\hbox {Mg}_{1/3}\hbox {Nb}_{2/3})\hbox {O}_{3}{-}x\hbox {Ba(Mg}_{1/8}\hbox {Nb}_{3/4})\hbox {O}_{3}$$ ceramics

The effect of Ba(\(\hbox {Mg}_{1/8}\hbox {Nb}_{3/4})\hbox {O}_{3}\) phase on structure and dielectric properties of \(\hbox {Ba(Mg}_{1/3}\hbox {Nb}_{2/3})\hbox {O}_{3}\) was studied by synthesizing \((1{-}x)\hbox {Ba(Mg}_{1/3}\hbox {Nb}_{2/3})\hbox {O}_{3}{-}x\hbox {Ba}(\hbox {Mg}_{1/8}\hbox {Nb}_{3/4})\hbox {O}_{3}\) (\(x = 0\), 0.005, 0.01 and 0.02) ceramics. Superlattice reflections due to 1:2 ordering appear as low as \(1000^{\circ }\hbox {C}\). \(\hbox {Ba}(\hbox {Mg}_{1/3}\hbox {Nb}_{2/3})\hbox {O}_{3}\) forms solid solution with \(\hbox {Ba}(\hbox {Mg}_{1/8}\hbox {Nb}_{3/4})\hbox {O}_{3}\) for all ‘x’ values studied until \(1350^{\circ }\hbox {C}\). Ordering was confirmed by powder X-ray diffraction pattern, Raman study and HRTEM. Ceramic pucks can be sintered to density \({>}92\%\) of theoretical density. Temperature and frequency-stable dielectric constant and nearly zero dielectric loss (tan \(\delta \)) were observed at low frequencies (20 MHz). The sintered samples exhibit dielectric constant (\(\varepsilon _{\mathrm{r}})\) between 30 and 32, high quality factor between 37000 and 74000 GHz and temperature coefficient of resonant frequency (\(\tau _{\mathrm{f}})\) between 21 and \(24\hbox { ppm }^{\circ }\hbox {C}^{-1}\).     

Resistance-switching properties of Bi-doped $$\hbox {SrTiO}_{3}$$ films for non-volatile memory applications with different device structures

\(\hbox {SrTiO}_{3}\) and Bi-doped \(\hbox {SrTiO}_{3}\) films were fabricated with different device structures using the sol–gel method for non-volatile memory applications, and their resistance-switching behaviour, endurance and retention characteristics were investigated. \(\hbox {SrTiO}_{3}\) and \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt have the same phase structure, morphologies and grain size; however, the grain size of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si is slightly larger than those of the \(\hbox {SrTiO}_{3}\) films grown on Si and the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Pt. The \(\hbox {SrTiO}_{3}\) or \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films grown on Si or Pt all exhibit bipolar resistive-switching behaviour and follow the same conductive mechanism; however, the \(\hbox {Ag}/\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}/\hbox {Si}\) device possesses the highest \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of \(10^{5}\) and the best endurance and retention characteristics. The doping of Bi is conducive to enhance the \(R_{\mathrm{HRS}}{/}R_{\mathrm{LRS}}\) of the \(\hbox {SrTiO}_{3}\) films; meanwhile, the Si substrates help improve the endurance and retention characteristics of the \(\hbox {Sr}_{0.92}\hbox {Bi}_{0.08}\hbox {TiO}_{3}\) films.     

Electrical and Thermal Characteristics of the Insulator–Metal Transition in Crystalline $$\hbox {V}_{2}\hbox {O}_{5}$$ Films

The electrical and thermal properties with respect to the crystallization in \(\hbox {V}_{2}\hbox {O}_{5}\) thin films were investigated by measuring the resistance at different temperatures and applied voltages. The changes in the crystal structure of the films at different temperatures were also explored using Raman measurements. The thermal diffusivity of the crystalline \(\hbox {V}_{2}\hbox {O}_{5}\) film was measured by the nanosecond thermoreflectance method. The microstructures of amorphous and crystalline \(\hbox {V}_{2}\hbox {O}_{5}\) were observed by SEM and XRD measurements. The temperature-dependent Raman spectra revealed that a structural phase transition does not occur in the crystalline film. The resistance measurements of an amorphous film indicated semiconducting behavior, whereas the resistance of the crystalline film revealed a substantial change near \(250\,{^{\circ }}\hbox {C}\), and Ohmic behavior was observed above \(380\,{^{\circ }}\hbox {C}\). This result was due to the metal–insulator transition induced by lattice distortion in the crystalline film, for which \(T_{\mathrm{c}}\) was \(260\,{^{\circ }}\hbox {C}\). \(T_{\mathrm{c}}\) of the film decreased from 260 \({^{\circ }}\hbox {C}\) to \(230\,{^{\circ }}\hbox {C}\) with increasing applied voltage from 0 V to 10 V. Furthermore, the thermal diffusivity of the crystalline film was \(1.67\times 10^{-7}\,\hbox {m}^{2}\cdot \hbox {s}^{-1}\) according to the nanosecond thermoreflectance measurements.     

Hysteresis and Instability in Some IPRT Sensors Within Temperature Ranges Extending from $$-196\,^{\circ }\hbox {C}$$ to $$150\,^{\circ }\hbox {C}$$150∘C

Industrial platinum resistance thermometer (IPRT) sensors or probes suffer from some instability on cycling over significant ranges of temperature and, specifically, from hysteresis in which the resistance tends to follow different paths for increasing temperatures compared with decreasing temperatures. The effect is well known, and cases of quite large hysteresis have been reported in the literature. Therefore, in establishing calibration and measurement capabilities for IPRT calibrations it is important to include an assessment of the performance which can be expected of a ‘typical good’ IPRT and to include this in the overall uncertainty which the laboratory can expect to achieve in such calibrations, even though the effect itself is outside the laboratory’s control. This paper presents results which have been obtained in cycling IPRT probes from four sources within various temperature ranges of current interest at NPL, between \(-196\,^{\circ }\hbox {C}\) and \(150\,^{\circ }\hbox {C}\), to see what levels of hysteresis may be expected. The cycles were carried out quite quickly in order to detect the hysteresis before it was mitigated by relaxation effects, but the time dependence was not itself studied. In most cases, hysteresis was \({<}0.0025\,^{\circ }\hbox {C}\) between \(0\,^{\circ }\hbox {C}\) and \(100\,^{\circ }\hbox {C}\), and \({<}0.0035\,^{\circ }\hbox {C}\) when the range extended down to \(-80\,^{\circ }\hbox {C}\) or up to \(150\,^{\circ }\hbox {C}\). Greater instability occurred when the sensors were cooled to \(-196\,^{\circ }\hbox {C}\).     

Synthesis,structural and dielectric properties of 0.8PMN–0.2PT relaxor ferroelectric ceramic

A 0.8PMN–0.2PT solid-solution ceramic was synthesized by columbite processing technique. The effects of sintering temperature on the density, structure and microstructure and in turn on the dielectric properties were investigated. The ceramics sintered at and above 1050\(^{\circ }\hbox {C}\) resulted in single-phase perovskite formation. However, high density >90% is achieved only after 1170\(^{\circ }\hbox {C}\). Microstructural analysis revealed that grain size increases with increase in sintering temperature. A significant increase in the peak of dielectric permittivity only after 1150\(^{\circ }\hbox {C}\) owing to increase in density is noted in this study. The quadratic law applied to this ceramic demonstrates that the transition is diffused. The broadness in phase transition and lower dielectric relaxation obtained for the composition demonstrate that the ceramic exhibits characteristics of both relaxor and normal ferroelectrics. The ceramic of composition 0.8PMN–0.2PT exhibits excellent dielectric properties \(\varepsilon _{\mathrm{r}\text {-}\mathrm{max}} =\) 20294?27338 at 100 Hz with \(T_{\mathrm{c}} = 100\)–\(96^{\circ }\hbox {C}\) at low sintering temperature 1170–1180\(^{\circ }\hbox {C}\), respectively.     

Influence of Thermal Annealings in Argon on the Structural and Thermochromic Properties of $$\mathrm{MoO}_{3}$$ Thin Films

The effect of thermal annealing in an inert atmosphere (argon) on the structural and thermochromic properties of \(\hbox {MoO}_{3}\) thin films was investigated. \(\hbox {MoO}_{3}\) thin films were deposited by thermal evaporation in vacuum of \(\hbox {MoO}_{3}\) powders. X-ray diffraction patterns of the films showed the presence of the monoclinic Magneli phase \(\hbox {Mo}_{9}\hbox {O}_{26}\) for annealing temperatures above \(250\,{^{\circ }}\hbox {C}\). Absorbance spectra of the films annealed in argon indicated that their thermochromic response increases with the annealing temperature in the analyzed range (23 \({^{\circ }}\hbox {C}\)–300 \({^{\circ }}\hbox {C}\)), a result opposite to the case of thermal annealings in air, for which case the thermochromic response shows a maximum value around 200 \({^{\circ }}\)C–225 \({^{\circ }}\)C and decreases for higher temperatures. These results are explained in terms of a higher density of oxygen vacancies formed upon thermal treatments in inert atmospheres.     

Dry Block Calibrator with Improved Temperature Field and Integrated Fixed-Point Cells

To reduce uncertainty of calibrations of contact thermometers using dry block calibrators, a concept was developed at Institute for Process Measurement and Sensor Technology of Technische Universität Ilmenau. This concept uses a multi-zone heating, heat flux sensors and a multiple fixed-point cell. The paper shows the concept and its validation on the basis of a dry block calibrator with a working temperature range of \(70\,^{\circ }\hbox {C}\) to \(430\,^{\circ }\hbox {C}\). The experimental results show a stability of \({\pm } 4\,\hbox {mK}\) for the reference temperature and axial temperature differences in the normalization block less than \({\pm }55\,\hbox {mK}\).     

Rectifying resistance-switching behaviour of Ag/SBTO/STMO/$$\hbox {p}^{+}$$-Si heterostructure films

The \(\hbox {Sr}_{0.88}\hbox {Bi}_{0.12}\hbox {TiO}_{3}/\hbox {SrTi}_{0.92}\hbox {Mg}_{0.08}\hbox {O}_{3}\) (SBTO/STMO) heterostructure films were prepared on \(\hbox {p}^{+}\hbox {-Si}\) substrates by sol–gel spin-coating technique, and the films had good crystallinity and uniform grain distribution. The heterostructure films with a structure of Ag/SBTO/STMO/\(\hbox {p}^{+}\hbox {-Si}\) exhibited a bipolar, remarkable resistance-switching characteristic, and \(R_{\mathrm{HRS}}/R_{\mathrm{LRS}}\,\,{\sim }10^{4}\). More importantly, the heterostructure films showed rectifying characteristic in the low resistance state (LRS), and the rectification ratio can reach \(10^{2 }\) at \(\pm 1\hbox { V}\). The dominant resistive-switching conduction mechanism of high resistance state (HRS) was Ohmic behaviour, and the LRS changed to space charge-limited current (SCLC).     

The Russian National Standard of Gases Humidity and Traceability System of Humidity Measurements

The Russian national humidity standard of gases has been modernized in order to increase the number of reproducible quantities of humidity (relative humidity, dew/frost-point temperature, mole fraction) and to extend the humidity and operating temperature ranges. The basis of the standard comprises two humidity generators with operating temperature ranges from \(5\,^{\circ }\hbox {C}\) to \(90\,^{\circ }\hbox {C}\) and from \(-60\,^{\circ }\hbox {C}\) to \(15\,^{\circ }\hbox {C}\). The common working range (from \(5\,^{\circ }\hbox {C}\) to \(15\,^{\circ }\hbox {C}\)) allows comparison of the generators. The generators use the two-pressure method to generate humid gas defined in terms of the relative humidity (from 5 %rh to 98 %rh at temperatures from \(90\,^{\circ }\hbox {C}\) to \(-60\,^{\circ }\hbox {C}\)) and the one-pressure (or phase equilibrium) method to generate humid gas defined in terms of the vapor mole fraction (from 0.6 ppm to \(700\times 10^{3}\) ppm) and dew/frost-point temperature (from \(-79\,^{\circ }\hbox {C}\) to \(90\,^{\circ }\hbox {C}\)). The expanded uncertainty in the relative humidity is no more than 0.2 %rh, no more than 1.2 % in the vapor mole fraction, and no more than \(0.12\,^{\circ }\hbox {C}\) in the dew/frost-point temperature. The ordinary hygrometers are traceable to the national primary standard in accordance with the state hierarchical chain for measuring means of gas humidity. The state hierarchical chain consists of three branches for means of measurements: (a) mole fraction, (b) dew/frost-point temperature, and (c) relative humidity with each branch represented as the scheme: primary standard–secondary standard–working standard–ordinary hygrometer. Calibration and verification of working standards and ordinary hygrometers, and their traceability to the primary standard use methods of (i) direct measurements, (ii) direct comparison, or (iii) comparison with a comparator.     

High-pressure studies of superconductivity in $$\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}$$

\(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\) crystallizes in tetragonal CeOBiS\(_{2}\) structure (S. G. P4/nmm). We have investigated the effect of pressure on magnetization measurements. Our studies suggest improved superconducting properties in polycrystalline samples of \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\). The \(T_{\mathrm{c}}\) in our sample is 5.3 K, at ambient pressure, which is marginal but definite enhancement over \(T_{\mathrm{c}}\) reported earlier (= 5.1 K). The upper critical field \(H_{\mathrm{c}2}\)(0) is greater than 3 T, which is higher than earlier report on this material. As determined from the M–H curve, both \(H_{\mathrm{c}2}\) and \(H_{\mathrm{c}1}\) decrease under external pressure P (0 \(\le P \le \) 1 GPa). We observe a decrease in critical current density and transition temperature on applying pressure in \(\hbox {BiO}_{0.75}\hbox {F}_{0.25}\hbox {BiS}_{2}\).     

Canadian Field Soils IV: Modeling Thermal Conductivity at Dryness and Saturation

The thermal conductivity data of 40 Canadian soils at dryness \((\lambda _{\mathrm{dry}})\) and at full saturation \((\lambda _{\mathrm{sat}})\) were used to verify 13 predictive models, i.e., four mechanistic, four semi-empirical and five empirical equations. The performance of each model, for \(\lambda _{\mathrm{dry}}\) and \(\lambda _{\mathrm{sat}}\), was evaluated using a standard deviation (SD) formula. Among the mechanistic models applied to dry soils, the closest \(\lambda _{\mathrm{dry}}\) estimates were obtained by MaxRTCM \((\textit{SD} = \pm ~0.018\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1})\), followed by de Vries and a series-parallel model (\(\hbox {S-}{\vert }{\vert }\)). Among the semi-empirical equations (deVries-ave, Advanced Geometric Mean Model (A-GMM), Chaudhary and Bhandari (C–B) and Chen’s equation), the closest \(\lambda _{\mathrm{dry}}\) estimates were obtained by the C–B model \((\pm ~0.022\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1})\). Among the empirical equations, the top \(\lambda _{\mathrm{dry}}\) estimates were given by CDry-40 \((\pm ~0.021\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1}\) and \(\pm ~0.018\,\hbox { Wm}^{-1}\cdot \hbox {K}^{-1}\) for18-coarse and 22-fine soils, respectively). In addition, \(\lambda _{\mathrm{dry}}\) and \(\lambda _{\mathrm{sat}}\) models were applied to the \(\lambda _{\mathrm{sat}}\) database of 21 other soils. From all the models tested, only the maxRTCM and the CDry-40 models provided the closest \(\lambda _{\mathrm{dry}}\) estimates for the 40 Canadian soils as well as the 21 soils. The best \(\lambda _{\mathrm{sat}}\) estimates for the 40-Canadian soils and the 21 soils were given by the A-GMM and the \(\hbox {S-}{\vert }{\vert }\) model.     

Thermal Conductivity of Pyroclastic Soil (<Emphasis Type="BoldItalic">Pozzolana</Emphasis>) from the Environs of Rome

The paper reveals the experimental procedure and thermo-physical characteristics of a coarse pyroclastic soil (Pozzolana), from the neighborhoods of Rome, Italy. The tested samples are comprised of 70.7 % sand, 25.9 % silt, and 3.4 % clay. Their mineral composition contained 38 % pyroxene, 33 % analcime, 20 % leucite, 6 % illite/muscovite, 3 % magnetite, and no quartz content was noted. The effective thermal conductivity of minerals was assessed to be about \(2.14\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\). A transient thermal probe method was applied to measure the thermal conductivity (\(\lambda \)) over a full range of the degree of saturation \((S_{\mathrm{r}})\), at two porosities (n) of 0.44 and 0.50, and at room temperature of about \(25\,^{\circ }\hbox {C}\). The \(\lambda \) data obtained were consistent between tests and showed an increasing trend with increasing \(S_{\mathrm{r}}\) and decreasing n. At full saturation (\(S_{\mathrm{r}}=1\)), a nearly quintuple \(\lambda \) increase was observed with respect to full dryness (\(S_{\mathrm{r}}=0\)). In general, the measured data closely followed the natural trend of \(\lambda \) versus \(S_{\mathrm{r}}\) exhibited by published data at room temperature for other unsaturated soils and sands. The measured \(\lambda \) data had an average root-mean-squared error (RMSE) of \(0.007\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) and \(0.008\,\hbox {W}{\cdot } \hbox {m}^{-1}{\cdot } \hbox {K}^{-1}\) for n of 0.50 and 0.44, respectively, as well as an average relative standard deviation of the mean at the 95 % confidence level \((\hbox {RSDM}_{0.95})\) of 2.21 % and 2.72  % for n of 0.50 and 0.44, respectively.     

Facile synthesis and characterization of rough surface $$\mathrm{V}_{2}\hbox {O}_{5}$$ nanomaterials for pseudo-supercapacitor electrode material with high capacitance

\(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials with rough surface were synthesized using commercial \(\hbox {V}_{2}\hbox {O}_{5}\), ethanol (EtOH) and \(\hbox {H}_{2}\hbox {O}\) as the starting materials by a simple hydrothermal route and combination of calcination. The electrochemical properties of \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials as electrodes in a supercapacitor device were measured using cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) method. \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials exhibit the specific capacitance of 423 F \(\hbox {g}^{-1}\) at the current density of 0.5 A \(\hbox {g}^{-1}\) and retain 327 F \(\hbox {g}^{-1}\) even at the high current density of 10 A \(\hbox {g}^{-1}\). The influence of the ratio of \(\hbox {EtOH/H}_{2}\hbox {O}\), the calcined time and temperature on the morphology, purity and electrochemical property of the products is discussed in detail. The results revealed that the ratio of \(\hbox {EtOH}\hbox {/}\hbox {H}_{2}\hbox {O}= 10\hbox {/}25\) and calcination at \(400{^{\circ }}\hbox {C}\) for 2–4 h are favourable for preparing \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials and they exhibited the best electrochemical property. The novel morphology and high specific surface area are the main factors that contribute to high electrochemical performance of \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials during the charge–discharge processes. It turns out that \(\hbox {V}_{2}\hbox {O}_{5}\) nanomaterials with rough surface is an ideal material for supercapacitor electrode in the present work.     

Thermodynamic Investigation of the Eutectic Mixture of the $$\hbox {LiNO}_{3}$$–$$\hbox {NaNO}_{3}$$NaNO3–$$\hbox {KNO}_{3}$$KNO3–$$\hbox {Ca}(\hbox {NO}_{3})_{2}$$Ca(NO3)2 System

Molten nitrate salt is usually employed as heat transfer or energy storage medium in concentrating solar power systems to improve the overall efficiency of thermoelectric conversion. In the present work, the liquidus curves of the \(\hbox {LiNO}_{3}\)–\(\hbox {NaNO}_{3}\)–\(\hbox {KNO}_{3}\)–\(\hbox {Ca}(\hbox {NO}_{3})_{2}\) system is determined by conformal ionic solution theory according to the solid–liquid equilibrium state of the binary mixture. The calculated eutectic temperature of the mixture is \(93.17\,{^{\circ }}\hbox {C}\), which is close to the experimental value of \(93.22\,{^{\circ }}\hbox {C}\) obtained from differential scanning calorimetry (DSC). Visualization observation experiments reveal that the quaternary eutectic mixture begins to partially melt when the temperature reaches \(50\,{^{\circ }}\hbox {C}\), and the degree of melting increases with temperature. The mixture is completely melted at \(\hbox {130}\,{^{\circ }}\hbox {C}\). The observed changes in the dissolved state at different temperatures correlate well with the DSC heat flow curve fluctuations.     

Enhanced infrared transmission characteristics of microwave-sintered $$\hbox {Y}_{2}\hbox {O}_{3}$$–$$\hbox {MgO}$$MgO nanocomposite

Infrared (IR) transparent ceramics are found to have applications in demanding defence and space missions. In this work, \(\hbox {Y}_{2}\hbox {O}_{3}\)–\(\hbox {MgO}\) nanocomposites were synthesised by a modified single-step combustion technique. The characterisation of the as-prepared powder by X-ray diffraction and transmission electron microscopy revealed the presence of cubic phases of ultra-fine nanostructured \(\hbox {Y}_{2}\hbox {O}_{3 }\) and MgO, with an average crystallite size of \({\sim }19 \hbox { nm}\). For the first time the resistive and microwave heatings were effectively coupled for sintering the sample, and it was found that the sintering temperature and soaking time were reduced considerably. The pellets were sintered to 99.2% of the theoretical density at \(1430{^{\circ }}\hbox {C}\) for a soaking duration of 20 min. The well-sintered pellets with an average grain size of \({\sim }200 \hbox { nm}\) showed better transmittance properties relative to pure yttria. The promising percentage transmission of 80% in the UV–visible region and 82% in the mid-IR region shown by \(\hbox {Y}_{2}\hbox {O}_{3}\)–\(\hbox {MgO}\) nanocomposites can be tailored and made cost-effective to fabricate high-quality IR windows for strategic defence and space missions.     

Synthesis,characterization and catalytic application of Ni catalysts supported on alumina–zirconia mixed oxides

Alumina and alumina–zirconia mixed oxides were compared as supports to prepare nickel catalysts. The oxides were prepared by the sol–gel method using aluminum tri-sec-butoxide and zirconium (IV) propoxide as precursors, and its physicochemical properties were determined by BET, TGA, DTA, XRD, SEM and TEM. The catalysts of nickel were obtained by the impregnation of the supports with nickel nitrate (10 wt%) and were heat-treated at \(700{^{\circ }}\hbox {C}\). The specific area of the supports and catalysts decreased with the increase in the zirconia content in agreement with the crystalline phase formed. TEM micrographs of nickel catalysts revealed particles in the size range of 10–30 nm. The \(\hbox {Ni/Al}_{2}\hbox {O}_{3}\)–\(\hbox {ZrO}_{2}\) catalysts were tested in the steam reforming reaction of ethanol (SRE) at \(500{^{\circ }}\hbox {C}\), and the obtained results suggest that the differences in catalytic activities depended on the content of \(\hbox {ZrO}_{2}\). The selectivity towards \(\hbox {H}_{2}\) was \({\sim }56\%\) for the named catalyst Ni–Al–0.25Zr.     

Synthesis and Characterization of Nb Substitution on (Bi-Pb)-2223 Superconductors

In this study, samples of \(\hbox {Bi}_{1.65}\hbox {Pb}_{{ 0.35-x}}\hbox {Nb}_{{ x}}\hbox {Sr}_{2}\hbox {Ca}_{2}\hbox {Cu}_{3}\hbox {O}_{10+\delta }\) were prepared by solid-state reaction method and the effect of Nb substitution for Pb on the structural and superconducting properties of this material was investigated. The room-temperature X-ray diffraction patterns indicated that all the samples have the dominant phase of high-\({T}_{\mathrm{c}}\) (Bi-2223). However, other phases such as Bi-2212 and some impurity phases like \(\hbox {SrCu}_{2}\hbox {O}_{2}\), \(\hbox {CuNb}_{2}\hbox {O}_{6}\), \(\hbox {CaCuO}_{3}\) and CuO were also obtained from XRD patterns. An increasing amount of \(\hbox {Nb}^{+5}\) substitutions for \(\hbox {Pb}^{+2}\) led to a phase transition from Bi-2223 to Bi-2212. Electrical resistivity and magnetic measurements revealed that the critical temperature and the critical current density decreases with increasing Nb content due to the enhancement of Bi-2212 phase and appearance of impurities. SEM images indicated that samples porosity changes due to the disrupted grain growth with the substitution of Pb ions with Nb ions.