Effect of composition on the properties of PEM based on polybenzimidazole and poly(vinylidene fluoride) blends

Inadequate performance, short term durability and high cost of polymer electrolyte membrane (PEM) are the major roadblocks that need to be resolved for successful commercialization of high temperature PEM fuel cell. In this report, we investigated the viability of previously developed miscible blend membranes of polybenzimidazole and poly (vinylidene fluoride) (PBI/PVDF), as potential PEMs. In addition, we have carried out several advanced analytical techniques such as dynamic mechanical analysis (DMA), ¹³C CP-MAS solid state NMR (SS-NMR) and wide-angle X-Ray diffraction (WAXD) to prove the miscible behavior of the polymer pair. Sub-ambient temperature DMA studies confirmed the miscible behavior of PBI/PVDF blends at different compositions based on single T_g criterion. SS-NMR and WAXD showed the presence of interactions between the functional groups of the polymers and their dependence on blend composition. Thermogravimetric analysis of phosphoric acid (PA) doped and undoped blend membranes confirmed the improved thermal stability of the membranes compared to neat PBI. The membranes exhibited excellent oxidative stability than pristine PBI membrane. The swelling ratio and volume after dipping in PA was found to be significantly low in the blend membranes owing to the hydrophobic nature of PVDF. Among the blends prepared, 90/10 and 75/25 membranes showed higher proton conductivity than PBI, attributed in part, to electronegativity of fluorine and crystallinity of PBI in PA that activate proton transport. The results demonstrated the potential usefulness of the blend membranes as PEM in fuel cell.     

Preparation and characterization of proton exchange membrane based on polyphosphoric acid modified by PVDF‐HFP

A polyphosphoric acid functionalized proton exchange membrane (PEM) was prepared by a ring opening reaction using the epoxycyclohexylethyltrimethoxysilane (EHTMS) and amino trimethylene phosphonic acid (ATMP) as raw materials and was modified by poly(vinylidene fluoride)–hexafluoro propylene (PVDF‐HFP). The structure of the membranes was characterized by Fourier transform infrared and scanning electron microscopy. The X‐ray photoelectron spectroscopy explores the content of the elements in the membrane related to the ion exchange capacity value. The membranes’ properties including water uptake, swelling ratio, proton conductivity, and hydrolysis stability were studied. Performance tests show that when ATMP/EHTMS = 1/5, conductivity of the PVDF‐HFP modified PEMs increased from 0.83 × 10^?4 S cm^?1 at 20 °C to 9.53 × 10^?3 S cm^?1 at 160 °C, the swelling ratio of membranes decreased from 2.71% to 2.13%. The results indicate that the introduction of F atoms is beneficial to increase the proton conductivity and the dimensional stability. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46737.     

The Preparation of Metal–Organic-Framework/Boron Phosphate Hybrid Materials for Improved Performances in Proton Exchange Membranes

New types of metal–organic framework based hybrid materials are designed and prepared, which involving the hybridization of various content of boron phosphate (BPO₄) with the precursor of HKUST-1. The structure of obtained HKUST-1/BPO₄ hybrid materials (HB) is fully investigated, and then applied to construct sulfonated poly (ether ether ketone) (SPEEK) based proton exchange membranes (SPEEK/HB). Owing to effective interactions between hybrid materials and SPEEK matrix, the achieved composite membranes reflect a considerable improvement in mechanical and thermal stability, oxidative stability, methanol permeation, and proton conductivity. In particular, the tensile strength of SPEEK/HB-20 composite membrane is 41.3 MPa, which is 1.5 times higher than pristine SPEEK, and the methanol permeability reduced to one-third of SPEEK at the same time. The SPEEK/HB-10 displays the highest proton conductivity of 37.4 mS cm⁻¹ at 80 °C, which is obviously higher than pristine SPEEK. These results reveal that the hybridization of HKUST-1 with BPO₄ provide a promising candidate in the modification of proton exchange membranes (PEMs), and this strategy also possess great application potential in other types of MOFs-based hybrid materials.     

Highly selective custom-made chitosan based membranes with reduced fuel permeability for direct methanol fuel cells

Custom-made nanocomposite proton exchange membranes (PEMs) are fabricated using the blends of sulfonated chitosan (S-Chitosan) and sulfonated graphene oxide (SGO) nanosheets for direct methanol fuel cells (DMFCs). Sulfonation of chitosan and GO are carried out by 1,3-propane sultone and sulfanilic acid, respectively. Scanning electron microscope (SEM) with energy dispersive X-ray investigation revealed that the thick, folded and wrinkled sheet-like morphology of SGO and the existence of elemental sulfur. SEM and atomic force microscopy images showed the uniform dispersion of hydrophilic SGO nanosheets. Besides the S-Chitosan/SGO membranes showed higher water uptake, swelling ratio and ion exchange capacity due to the enhancement in hydrophilicity. The modified PEMs displayed improvement in proton conductivity since the ion-exchangeable sulfonic acid groups facilitate the proton conduction and effectively resist the methanol permeability by forming a strong hydrogen bond network with chitosan and thus diminish the void volume. Particularly, S-Chiotsan-1 membrane showed superior proton conductivity of 4.86 × 10⁻³ Scm⁻¹ at (25°C), selectivity of 1.89 × 10⁵ Scm⁻³ s and lesser methanol permeability of 2.57 × 10⁻⁸ cm²s⁻¹. Overall results suggest that the S-Chitosan/SGO membranes found to be a suitable alternate for Nafion® in DMFCs.     

Pre‐Oxidized Acrylic Fiber Reinforced Ferric Sulfophenyl Phosphate‐Doped Polybenzimidazole‐Based High‐Temperature Proton Exchange Membrane

Pre‐oxidized acrylic fiber (POAF) and ferric sulfophenyl phosphate (FeSPP) are incorporated into polybenzimidazole (PBI) membrane for the first time to prepare high‐temperature proton exchange membranes (PEMs). The strong hydrogen bonds formed between PBI/POAF and FeSPP lead to good dispersion of POAF and FeSPP, facilitate the construction of proton channels, and enhance the dimensional and mechanical stability of the membranes. PBI/FeSPP (30 wt%) shows good proton conductivity (5.43 × 10⁻² and 4.13 × 10⁻² S cm⁻¹ at 180 °C at 50% and 0 relative humidity (RH), respectively) and improved dimensional and mechanical stability compared with pristine PBI. By incorporating 5 wt% POAF into PBI/FeSPP (30 wt%), the swelling ratios are halved and the mechanical strength is enhanced by almost 30% while the proton conductivity is slightly affected (3.84 × 10⁻² and 2.97 × 10⁻² S cm⁻¹ at 180 °C at 50% and 0 RH for PBI/FeSPP (30 wt%)/POAF (5 wt%), respectively). This work offers a new route in the preparation of high‐temperature PEMs with enhanced properties.

     

Solution‐blown SPEEK/POSS nanofiber–nafion hybrid composite membranes for direct methanol fuel cells

This study aims to develop novel hybrid composite membranes (NHMs) by impregnating Nafion solution into the porous sulfonated poly(ether ether ketone)/polyhedral oligomeric silsesquioxanes (SPEEK/POSS) nanofibers (NFs). The composite membrane was prepared by solution blowing of a mixture of SPEEK/POSS solution. The characteristics of the SPEEK/POSS NFs and the NHMs, including morphology, thermal stability, and performance of membrane as PEMs, were investigated. The performance of NHMs was compared with that of Nafion117 and SPEEK/Nafion composite membranes. Results showed that the introduction of POSS improved the proton conductivity, water swelling, and methanol permeability of membranes. A maximum proton conductivity of 0.163 S cm^?1 was obtained when the POSS content was 6 wt % at 80°C, which was higher than that of Nafion117 and SPEEK/Nafion. NHMs could be used as proton exchange membranes (PEMs) for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42843.     

Nafion® reinforced with polyacrylonitrile/ZrO2 nanofibers for direct methanol fuel cell application

Nafion® membrane blended with polyacrylonitrile nanofibers decorated with ZrO₂ was successfully fabricated. The composite membrane showed improved proton conductivity, swelling ratio, thermal and mechanical stability, reduced methanol crossover, and enhanced fuel cell efficiency. The nanocomposite membranes achieved a reduced methanol crossover of 5.465 × 10⁻⁸ cm² S⁻¹ compared to 9.118 × 10⁻⁷ cm² S⁻¹ of recast Nafion® membrane using a 5 M methanol solution at 80°C. The composite membrane also showed an ion conductivity of 1.84 compared to 0.25 S cm⁻¹ recast Nafion® at 25°C. The composite membranes showed a peak power density of 68.7 mW·cm⁻² at 25°C, these results show a promising composite membrane for fuel cell application.     

Preparation and properties of chitosan/acidified attapulgite composite proton exchange membranes for fuel cell applications

A composite proton exchange membrane chitosan (CS)/attapulgite (ATP) was prepared with the organic–inorganic compounding of ATP and CS. The composite membranes were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), and fourier transform infrared spectroscopy (FTIR). The mechanical properties, thermal stability, water uptake, and proton conductivity of the composite membranes were fully investigated. The composite membranes exhibited an enhanced mechanical property, dimensional and thermal stability compared to CS membrane, owing to the interface interaction between ATP and CS. The maximum tensile strength of 53.1 MPa and decomposition temperature of 223.4°C was obtained, respectively. More importantly, the proton conductivity of the composite membrane is also enhanced, the composite membrane with 4 wt% ATP content (CS/ATP-4) exhibited the highest proton conductivity of 26.2 mS cm⁻¹ at 80°C with 100% relative humidity, which is 25.1% higher than pure CS membrane. These results may explore a simple and green strategy to prepare CS-based PEMs, which have a great potential in the application of proton exchange membrane fuel cells.     

Fabrication and characterization of sulfonated polybenzimidazole/sulfonated imidized graphene oxide hybrid membranes for high temperature proton exchange membrane fuel cells

The sulfonated polybenzimidazole (sPBI)/sulfonated imidized graphene oxide (SIGO) was evaluated to be a potential candidate for high temperature proton exchange membranes fuel cells (HT-PEMFCs). Multifunctionalized covalently bonded SIGO is incorporated in sPBI matrix to resolve the drawbacks such as low proton conductivity, poor water uptake, and ion-exchange capacity (IEC) of sPBI polymer, synthesized by direct polycondensation in phosphoric acid for the application of proton exchange membranes. Strong hydrogen bonding among multifunctional groups established a neighborhood of interconnected hydrophobic graphene sheets and organic polymer chains. It provides hydrophobic–hydrophilic phase separation and facile proton hopping architecture. The optimized sPBI/SIGO (15 wt %) revealed 2.45 meq g⁻¹ IEC; 5.81 mS cm⁻¹ proton conductivity [120 °C and 10% relative humidity (RH)] and 2.45% bound water content. The maximum power density of the sPBI/SIGO-15 membrane was 0.40 W cm⁻² at 160 °C (5% RH) and ambient pressure with stoichiometric feed of H₂/air. This recommends that sPBI/SIGO composite membranes are compatible candidate for HT-PEMFCs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47892.     

Novel crosslinked AB‐type polyphenylquinoxaline membranes for high‐temperature proton exchange membrane fuel cells

AB‐type polyphenylquinoxaline (ABPPQ) membranes exhibit great mechanical properties and thermal properties for high‐temperature proton exchange membranes (PEMs). However, they dissolve in high‐concentration phosphoric acid (PA) during acid doping. In order to improve the PA resistant of ABPPQ, crosslinked ABPPQ membranes were prepared using sulfuric acid. The crosslinked ABPPQ membranes showed high PA resistance. The acid content of PA‐doped membranes decreased slightly with crosslinking, but the crosslinked polyphenylquinoxaline (CPPQ)‐20 membrane could reach 2.5 × 10^?2 S/cm proton conductivity at 160°C. Membrane electrode assemblies were fabricated with an active area of 4 cm² and Pt loading of 1 mg/cm². A startup and shutdown test (operated at 150°C with 0.2 A/cm² for 12 h and then 12 h off at room temperature) and a 30‐day long‐term durability test (150°C with 0.2 A/cm²) were conducted. In the startup and shutdown test, the crosslinked membranes showed a low open‐circuit voltage decay rate of 0.15 mV/h. In the 30‐day long‐term durability test, the voltage decay rate was 0.039 mV/h. In both tests, the crosslinked membranes showed a stable performance. Therefore, the crosslinked ABPPQ membranes can be regarded as a novel material for high‐temperature PEM fuel cells. POLYM. ENG. SCI., 59:2169–2173, 2019. © 2019 Society of Plastics Engineers     

EB‐crosslinked Polymer Electrolyte Membranes Based on Highly Sulfonated Poly(ether ether ketone) and Poly(vinylidene fluoride)/Triallyl Isocyanurate

In this study, crosslinked polymer electrolyte membranes for polymer electrolyte membrane fuel cell (PEMFC) applications are prepared using electron beam irradiation with a mixture of sulfonated poly(ether ether ketone) (SPEEK), poly(vinylidene fluoride) (PVDF), and triallyl isocyanurate (TAIC) at a dose of 300 kGy. The gel‐fraction of the irradiated SPEEK/PVDF/TAIC (95/4.5/0.5) membrane is 87% while the unirradiated membrane completely dissolves in DMAc solvent. In addition, the water uptake of the irradiated membrane is 221% at 70 °C while that of the unirradiated membrane completely dissolves in water at above 70 °C. The ion exchange capacity and proton conductivity of the crosslinked membrane are 1.57 meq g⁻¹, and 4.0 × 10⁻² S cm⁻¹ (at 80 °C and RH 90%), respectively. Furthermore, a morphology study of the membranes is conducted using differential scanning calorimetry and X‐ray diffractometry. The cell performance study with the crosslinked membrane demonstrates that the maximum power density is 518 mW cm⁻² at 1036 mA cm⁻² and the maximum current density at applied voltage of 0.4 V is 1190 mA cm⁻².     

Novel Proton Conducting Membranes from the Combination of Sulfonated Polymers of Polyetheretherketones and Polyphosphazenes Doped with Sulfonated Single‐Walled Carbon Nanotubes

Intent on developing efficient proton exchange membranes used for direct methanol fuel cells as well as hydrogen fuel cells, a series of membranes based on sulfonated polyetheretherketone and sulfonated polyphosphazene‐graft copolymers is prepared by cross‐linking reaction because the former material has good enough mechanical property, while the latter is excellent in the proton transfer. The cross‐linked membranes combine the advantages of the two kinds of polymers. Among them, the membrane poly[(4‐trifluoromethylphenoxy)(4‐methylphenoxy)phosphazene]‐g‐poly {(styrene)₁₁‐r‐[4‐(4‐sulfobutyloxy)styrene]₃₃‐sulfonated poly(ether ether ketone)75 (CF₃‐PS₁₁‐PSBOS₃₃‐SPEEK75) shows a proton conductivity at 0.143 S cm⁻¹ under fully hydrated conditions at 80 °C and performs tensile strength about five times as much as did the sulfonated polyphosphazene membrane CF₃‐PS₁₁‐PSBOS₃₃. Further doping of sulfonated single‐walled carbon nanotubes (S‐SWCNTs) into the cross‐linked membranes on the screening of additives gives composite membrane CF₃‐PS₁₁‐PSBOS₃₃‐SPEEK75‐SWCNT possessing proton conductivity of 0.196 S cm⁻¹, even higher than that of Nafion 117 and a tensile strength comparable to that of Nafion 117. However, this significance of the composite membrane in the proton conduction is not observed in the test with a H₂/air fuel cell when it shows a maximal power density of 280 mW cm⁻² at 80 °C, whereas 294 mW cm⁻² is observed for CF₃‐PS₁₁‐PSBOS₃₃‐SPEEK75.

     

New organic–inorganic hybrid membranes based on sulfonated polyimide/aminopropyltriethoxysilane doping with sulfonated mesoporous silica for direct methanol fuel cells

A series of novel composite methanol‐blocking polymer electrolyte membranes based on sulfonated polyimide (SPI) and aminopropyltriethoxysilane (APTES) doping with sulfonated mesoporous silica (S‐mSiO₂) were prepared by the casting procedure. The microstructure and properties of the resulting hybrid membranes were extensively characterized. The crosslinking networks of amino silica phase together with sulfonated mesoporous silica improved the thermal stability of the hybrid membranes to a certain extent in the second decomposition temperature (250–400°C). The composite membranes doping with sulfonated mesoporous silica (SPI/APTES/S‐mSiO₂) displayed superior comprehensive performance to the SPI and SPI/APTES membranes, in which the homogeneously embedded S‐mSiO₂ provided new pathways for proton conduction, rendered more tortuous pathways as well as greater resistance for methanol crossover. The hybrid membrane with 3 wt % S‐mSiO₂ into SPI/APTES‐4 (SPI/A‐4) exhibited the methanol permeability of 4.68 × 10^?6 cm² s^?1at 25°C and proton conductivity of 0.184 S cm^?1 at 80°C and 100%RH, while SPI/A‐4 membrane had the methanol permeability of 5.16 × 10^?6 cm² s^?1 at 25°C and proton conductivity of 0.172 S cm^?1 at 80°C and 100%RH and Nafion 117 exhibited the values of 8.80 × 10^?6 cm² s^?1 and 0.176 S cm^?1 in the same test conditions, respectively. The hybrid membranes were stable up to about 80°C and demonstrated a higher ratio of proton conductivity to methanol permeability than that of Nafion117. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

High Performance Ion Exchange Membranes Prepared via Direct Polyacylation of Racemic and (S)‐1,1′‐Binaphthyl‐Based Cationic/Anionic Monomers

Side‐chain‐type sulfonated/quaternized aromatic polyelectrolytes with precisely controlled contents of ionized groups are successfully synthesized via direct polyacylation of sulfonated/quaternized monomers based on 2,2′‐dihydroxy‐1,1′‐binaphthyl (DHBN). Both proton exchange membranes (PEMs) and anion exchange membranes (AEMs) of the corresponding polyelectrolytes exhibit outstanding properties. Proton conductivity (116 mS cm^?1 at 30 °C) higher than Nafion 115 for the PEMs and OH^– conductivity (28.5–53.7 mS cm^?1 at 30 °C) comparable to Tokuyama A901 for the AEMs are accomplished. In addition, the AEMs can withstand 60 days’ aging in 1 mol L^?1 NaOH at 60 °C without degradation, as proved by ¹H NMR. More intriguingly, when starting from optically active (S)‐DHBN instead of racemic DHBN, an enhancement in proton conductivity of PEMs is observed for the first time, which opens a new door to optically active ion exchange membranes.     

Polymer electrolyte membranes having sulfoalkyl grafts into ETFE film prepared by radiation‐induced copolymerization of methyl acrylate and methyl methacrylate

Polymer electrolyte membranes (PEMs) containing alkylsulfonic acid grafts can be prepared by radiation‐induced graft copolymerization of methyl acrylate (MA) and methyl methacrylate (MMA) into a poly(ethylene‐co‐tetrafluoroethylene) film followed by sulfonation of the MA units in the copolymer grafts using an equimolar complex of chlorosulfonic acid and 1,4‐dioxane (ClSO₃H‐Complex). PEMs with MA/MMA copolymer grafts that are 33%–79% MA units were prepared by preirradiation with a dose of 20 kGy and grafting in bulk comonomers at 60°C. The grafted films are treated with ClSO3H‐Complex to obtain PEMs with ion exchange capacity of 0.36‐0.81 mmol/g (sulfonation degrees of 20%–40%) and proton conductivity of 0.04‐0.065 S/cm. These values can be controlled by changing the MA content the sulfonation occurring at an α‐carbonyl carbon. The PEMs with higher MMA content showed higher durability in water (80°C) and under oxidative conditions (3% H₂O₂) at 60°C. This is because the PMMA grafts in the PEMs have no proton at an α‐carbonyl carbon, which is considered to be a trigger of the degradation of grafting polymers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The Construction and Application of Dual-Modified Carbon Nanotubes in Proton Exchange Membranes with Enhanced Performances

In this study, the carbon nanotubes (CNTs) are successively coated via sol-gel method with SiO₂ (SiO₂@CNTs), followed by grafting with 3-merraptnpropyltrimethnxysilane and oxidation with hydrogen peroxide to yield dual-modified CNTs (SSiO₂@CNTs). The SSiO₂@CNTs material is applied to prepared chitosan (CS) based composite proton exchange membranes by the incorporation of various content of SSiO₂@CNTs, the structure and properties of as-prepared composite membranes are fully investigated. Compared to pristine CS membrane, the SSiO₂@CNTs-filled composite membranes show improved thermal stability, mechanical stability, and methanol resistance, owing to the effective interface interaction and good compatibility between SSiO₂@CNTs and CS matrix. Additionally, the doping of SSiO₂@CNTs also generates a positive effect on the electrochemistry performance, due to the construction of abundant transport channel and providing more proton sources or proton sites. Particularly, the CS/SSiO₂@CNTs-7 membrane exhibits tensile strength of about 40.1 MPa and proton conductivity of 35.8 mS cm⁻¹ at 80 °C, which is almost 1.6 and 2.0 times higher than pure CS membrane, and lower methanol permeability of 0.9 × 10⁻⁶ cm² s⁻¹. The direct methanol fuel cell performance (DMFC) of CS/SSiO₂@CNTs-7 membrane is also improved with open circuit voltage of 0.67 V and maximum power density of 60.7 mW cm⁻² at 70 °C.     

Sulfonated poly(phenylene ether ether sulfone) membrane tailored with layer-by-layer self-assembly of poly(diallyldimethylammonium chloride) and phosphotungstic acid for DMFC applications

Poly(diallyldimethylammonium chloride) (PDDA) and phosphotungstic acid (PTA) were used as cationic and anionic polyelectrolyte layers, respectively, in an alternating fashion to enhance the methanol barrier property and oxidative stability of sulfonated poly (phenylene ether ether sulfone) (SPEES) proton exchange membranes (PEMs). The multilayer PEMs were characterized by AFM, FTIR, and AC impedance spectroscopy. Methanol permeability of the multilayered membranes was found to be much lower than the bare SPEES membrane. The multilayered membranes displayed significantly improved oxidative stability and dimensional stability compared to pristine SPEES membrane. Conversely, the water uptake (%) and proton conductivity (S cm⁻¹) of the prepared membranes decrease to some extent with increasing the PDDA/PTA bilayers in comparison to the pristine SPEES membrane. The maximum relative selectivity (2.23 × 10⁴ S cm⁻³ s) and retained weight (88.9%) were observed for SPEES-[PDDA/PTA]₅ multilayered membrane. The obtained results exposed the possibility of SPEES-[PDDA/PTA]₅ multilayered membrane to serve as high-performance PEMs in direct methanol fuel cells. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47344.     

Hydrophilic TiO2 decorated carbon nanotubes/sulfonated poly(ether ether ketone) composite proton exchange membranes for fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is currently considered to be one of the most potential candidates of commercial perfluorinated sulfonic acid proton exchange membranes. To balance the proton conductivity and mechanical properties of SPEEK, nano TiO₂ coated carbon nanotubes (TiO₂@CNTs) were prepared using a benzyl alcohol-assisted sol-gel method and then used as a new nanofiller to modify SPEEK to prepare SPEEK/TiO₂@CNTs composite membranes. The thick insulated TiO₂ coating layer can effectively avoid the risk of electronic short-circuiting formed by CNTs, while the hydrophilicity of TiO₂ can also reduce the polar difference between CNTs and SPEEK matrix, thus promoting the homogeneous dispersion of CNTs in the composites. As a result, the composite membranes demonstrated simultaneously improved strength and proton conductivity. Incorporating 5 wt% of TiO₂@CNTs exhibited 31% growth in mechanical strength when compared with pure SPEEK. Moreover, the maximum conductivity was 0.104 S cm⁻¹ (80°C) for the composite membrane with 5 wt% of TiO₂@CNTs, which was nearly twice as high as that of SPEEK membrane (0.052 S cm⁻¹).     

High Molecular Weight Polybenzimidazole Membranes for High Temperature PEMFC

High temperature operation of proton exchange membrane fuel cells under ambient pressure has been achieved by using phosphoric acid doped polybenzimidazole (PBI) membranes. To optimize the membrane and fuel cells, high performance polymers were synthesized of molecular weights from 30 to 94 kDa with good solubility in organic solvents. Membranes fabricated from the polymers were systematically characterized in terms of oxidative stability, acid doping and swelling, conductivity, mechanical strength and fuel cell performance and durability. With increased molecular weights the polymer membranes showed enhanced chemical stability towards radical attacks under the Fenton test, reduced volume swelling upon the acid doping and improved mechanical strength at acid doping levels of as high as about 11 mol H₃PO₄ per molar repeat polymer unit. The PBI‐78kDa/10.8PA membrane, for example, exhibited tensile strength of 30.3 MPa at room temperature or 7.3 MPa at 130 °C and a proton conductivity of 0.14 S cm^–1 at 160 °C. Fuel cell tests with H₂ and air at 160 °C showed high open circuit voltage, power density and a low degradation rate of 1.5 μV h^–1 at a constant load of 300 mA cm^–2.     

Partially Sulfonated Poly(1,4‐phenylene ether‐ether‐sulfone) and Poly(vinylidene fluoride) Blend Membranes for Fuel Cells

Blend membranes based on high conductive sulfonated poly(1,4‐phenylene ether‐ether‐sulfone) (SPEES) and poly(vinylidene fluoride) (PVDF) having excellent chemical stability were prepared and characterized for direct methanol fuel cells. The effects of PVDF content on the proton conductivity, water uptake, and chemical stability of SPEES/PVDF blend membranes were investigated. The morphology, miscibility, thermal, and mechanical properties of blend membranes were also studied by means of scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA) measurements. The blend membrane containing 90 wt.% SPEES (degree of sulfonation – DS = 72%) and 10 wt.% PVDF (M_w = 180,000) exhibits optimum properties among various SPEES72/PVDF membranes. Addition of PVDF enhanced resistance of the SPEES membrane against peroxide radicals and methanol significantly without deterioration of its proton conductivity. It's proton conductivity at 80 °C and 100% relative humidity is higher than Nafion 115 while it's methanol permeability is only half of that of Nafion 115 at 80 °C. The direct methanol fuel cell performance of the SPEES membranes was better than that of Nafion 115 membrane at 80 °C.