Regenerated cellulose fibers as impact modifier in long jute fiber reinforced polypropylene composites: Effect on mechanical properties,morphology, and fiber breakage

Polypropylene/jute fiber (PP‐J) composites with various concentrations of viscose fibers (VF) as impact modifiers and maleated polypropylene (MAPP) as a compatibilizer have been studied. The composite materials were manufactured using direct long fiber thermoplastic (D‐LFT) extrusion and compression molding. The effect of fiber length, after the extrusion process, on composites mechanical performance and toughness was investigated. The results showed that the incorporation of soft and tough VF on the PP‐J improved the energy absorption of the composites. The higher impact strength was found with the addition of 10 wt % of the impact modifier, but the increased concentration of the impact modifier affected the tensile and flexural properties negatively. Similarly, HDT values were reduced with addition of viscose fibers whereas the addition of 2 wt % of maleated polypropylene significantly improved the overall composite properties. The microscopic analysis clearly demonstrated longer fiber pullouts on the optimized impact modified composite. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41301.     

Investigations on weld joining of sisal CSM‐thermoplastic composites

An experimental study was conducted to investigate joint efficiency of both, butt, and lap joints of sisal CSM reinforced polymer composites. The thermoplastics, HDPE, and polypropylene (PP) were used separately as matrices in composites. Sisal‐HDPE composites exhibited excellent improvement in tensile strength that reached up to 47.5 MPa at 30 phr loading of sisal CSM as compared with 17.7 MPa of HDPE. Significant improvement in HDT was also observed that increased from 60.2 to 75°C on 0 to 30 phr reinforcement of sisal CSM in HDPE. Similar improvement was noticed with PP where in HDT improved from 69 to 87.6°C on incorporation of 0 to 30 phr sisal CSM. Hot tool welding process was employed for joining the composite materials. The joint efficiency of butt joint of HDPE was observed as 30%. It varied from 48 to 59% for lap joints of different sizes. The joint efficiencies of 20 mm lap joints of different compositions were observed as 59, 98, 75, and 58% in 0, 10, 20, and 30 phr Sisal CSM‐HDPE composites, respectively. Welded joint strengthening is attributed to partial reinforcement of interface that occurs during softening of matrix material which allowed spring back of originally pressed fibers followed by their repositioning in the welded part. POLYM. COMPOS., 36:214–220, 2015. © 2014 Society of Plastics Engineers     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical properties and water absorption of fiber‐reinforced polypropylene composites prepared by bagasse and beech fiber

The present study investigates the tensile, flexural, notched Izod impact, and water absorption properties of bagasse and beech reinforced polypropylene (PP) composites as a function of fiber content. The surface of fibers was modified through the use of maleated polypropylene (MAPP) coupling agent. From this study, it was found that mechanical properties increase with an increase in fiber loading in both cases. However, the addition of wood fibers resulted in a decrease in impact strength of the composites. The water absorption property at varying fiber loading was evaluated and found maximum for the BA/PP composites. The weight gains for all specimens were less than 7%. In general, the results showed the usefulness of bagasse fiber as a good alternative and reinforcing agent for composite. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

Mechanical properties of short sisal fiber‐reinforced polypropylene composites: Comparison of experimental data with theoretical predictions

Sisal fibers were used for the reinforcement of a polypropylene (pp) matrix. Composites consisting of polypropylene reinforced with short sisal fibers were prepared by melt‐mixing and solution‐mixing methods. A large amount of fiber breakage was observed during melt mixing. The fiber breakage analysis during composite preparation by melt mixing was carried out using optical microscopy. A polynomial equation was used to model the fiber‐length distribution during melt mixing. The experimental mechanical properties of sisal/PP composites were compared with existing theoretical models such as the modified rule of mixtures, parallel and series models, the Hirsch model, and the Bowyer–Baders model. The dependence of the tensile strength on the angle of measurement with respect to fiber orientation also was modeled. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 602–611, 2003     

High Stiffness Natural Fiber‐Reinforced Hybrid Polypropylene Composites

Abstract

Natural fibers are potentially a high‐performance non‐abrasive reinforcing fiber source. In this study, pulp fibers [including bleached Kraft pulp (BKP) and thermomechanical pulp (TMP)], hemp, flax, and wood flour were used for reinforcing in polypropylene (PP) composite. The results show that pulp fibers, in particular, TMP‐reinforced PP has the highest tensile strength, possibly because pulp fibers were subjected to less severe shortening during compounding, compared to hemp and flax fiber bundles. Maleic‐anhydride grafted PP (MAPP) with high maleic anhydride groups and high molecular weight was more effective in improving strength properties of PP composite as a compatiblizer. Coupled with 10% glass fiber, 40% TMP reinforced PP had a tensile strength of 70 MPa and a specific tensile strength comparable to glass fiber reinforced PP. Thermomechanical pulp was more effective in reinforcing than BKP. X‐ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) were used to aid in the analysis. Polypropylene with high impact strength was also used in compounding to improve the low‐impact strength prevalent in natural fiber‐reinforced PP from injection molding.     

Polypropylene‐based composites reinforced with textile wastes

The present work describes the preparation of polypropylene composites reinforced with cotton fibers, which were obtained from textile waste. The cellulosic fibers were bleached and then chemically modified on the surface using acetylation or silanization methods. Fourier transform infrared spectroscopy analysis and energy dispersive X‐ray spectroscopy confirmed the efficiency of both treatments. Results of thermal degradation by thermogravimetric analysis (TGA) of treated fibers indicated that the acetylated ones decreased thermal stability while the silanized fibers increased this property. The influence of the chemical modifications and fibers content in polypropylene‐based composites was studied by thermomechanical and mechanical properties (dynamic mechanical analysis and tensile tests) and thermal analyses (TGA and differential scanning calorimetry). The results showed that the addition of the obtained cellulose fibers in polypropylene caused increase of storage and Young's moduli, along with stress at break. Moreover, scanning electronic microscopy micrographs of cryofractured surfaces revealed stronger adhesion between fiber and matrix in the composites reinforced with the modified fibers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45060.     

Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

Impact toughness,viscoelastic behavior,and morphology of polypropylene–jute–viscose hybrid composites

In this investigation, we studied the impact toughness and viscoelastic behavior of polypropylene (PP)–jute composites. In this study, we used viscose fiber as an impact modifier and maleated PP as a compatibilizer. The toughness of the composites was studied with conventional Charpy and instrumental falling‐weight impact tests. The composites’ viscoelastic properties were studied with dynamic mechanical analysis. The results show that the incorporation of viscose fibers improved the impact strength and toughness to 134 and 65% compared to those of the PP–jute composites. The tan δ peak amplitude also increased with the addition of the impact modifier and indicated a greater degree of molecular mobility. The thermal stability of the composites was evaluated with thermogravimetric analysis. The addition of 2 wt % maleated polypropylene (MAPP) to the impact‐modified composite improved the impact strength and toughness to 144 and 93%, respectively. The fiber–matrix morphology of the fracture surface and the Fourier transform infrared spectra were also studied to ascertain the existence of the type of interfacial bonds. Microstructural analysis showed the retention of viscose fibers in the composites compared to the more separated jute fibers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42981.     

石墨烯增强聚丙烯/高密度聚乙烯纤维研究

针对聚丙烯（PP）纤维拉伸强度不够高和刚性差的缺点,采用高密度聚乙烯（PE-HD）及石墨烯通过熔融法制备PP/PE-HD/石墨烯纤维;通过偏光显微镜、拉伸强度、扫描电子显微镜、差式扫描量热仪、傅里叶红外光谱仪等测试研究了石墨烯加入对PP/PE-HD纤维性能的影响。结果表明,当加入25份（质量份数,下同）PE-HD,改性纤维的拉伸强度达2.46 GPa,与PP纤维的拉伸强度相比提升了8 %;当继续加入0.3份石墨烯时, PP/PE-HD/石墨烯纤维的拉伸强度比PP/PE-HD纤维提高了1.6 %;加入PE-HD和石墨烯改性后,PP纤维的热稳定性改善。     

A low‐cost,low‐fiber‐breakage,injection molding process for long sisal fiber reinforced polypropylene

Composites of polypropylene (PP) and non‐treated sisal fiber (SF) were prepared in a non‐conventional two‐step process that offers significant advantages. Maleic anhydride–grafted polypropylene (MA‐g‐PP) was used as a coupling agent, to improve adhesion between the polar sisal fiber and the non‐polar polypropylene continuous matrix. At a first step, SF/MA‐g‐PP pellets with large aspect ratio and very high fiber content are prepared by extrusion impregnation and coating of a continuous SF yarn, followed by cooling and cutting. The composite pellets are thus dry blended with regular PP pellets in the injection machine hopper, and injected to obtain composite tensile specimens with a minimum quantity of expensive MA‐g‐PP, minimum fiber breakage and thermal degradation, and excellent mechanical properties. The SF/MA‐g‐PP pellets have a fiber content of 70% (w/w). The composite tensile specimens have final fiber contents ranging from about 3.5% to 24.5% (w/w). The PP tensile strength rises by about 44%. The tensile modulus increases by 126%, and the heat distortion temperature (HDT) is raised by about 35 K. FT‐IR spectroscopy and SEM micrographic observation show that the MA‐g‐PP is covalently bonded to SF through esterification. Besides the improvement in mechanical and thermal properties, costs are reduced because of the lower content of very expensive MA‐g‐PP, and the use of a single‐screw extruder at high production rates. Polym. Eng. Sci. 44:1766–1772, 2004. © 2004 Society of Plastics Engineers.     

A comparative study on mechanical properties and water absorption behavior of fiber‐reinforced polypropylene composites prepared by OCC fiber and aspen fiber

Fiber‐reinforced polymers have received considerable attention from industry in recent years. Due to the sharp ecological damage, worldwide shortage of trees in many areas and the global demand for fibrous material, there has been growing interest in the use of recycled wood fiber as an alternative or substitute fiber source. The present study investigates the tensile, flexural, Izod impact, and water absorption behavior of Old Corrugated Container (OCC) and aspen (AS) reinforced polypropylene (PP) composites as a function of fiber content. The surface of AS and OCC fibers was modified through the use of MAPP coupling agent. From the studies it was found that mechanical properties increase with increase in fiber loading in both cases. However the addition of wood fibers resulted in a decrease in impact strength of the composites. The water absorption property at varying fiber loading were evaluated and found maximum for the OCC/PP composites. The weight gains for all specimens were less than 3.5%. Finally, the results showed the usefulness of OCC fiber as a good alternative and reinforcing agent for composite. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Structure–property relationship studies in amine functionalized multiwall carbon nanotubes filled polypropylene composite fiber

Amine functionalized multiwalled carbon nanotubes (a‐MWNT) based polypropylene (PP) composite fibers were prepared in the presence of polypropylene‐g‐maleic anhydride (PP‐g‐MA) by melt‐mixing followed by melt‐spinning with subsequent post‐drawing of the as‐spun fibers of varying draw ratio (DR). In order to enhance the interfacial interaction, a‐MWNT were utilized in combination with PP‐g‐MA during melt‐mixing. Fourier transform infrared spectroscopic analysis revealed the formation of imide bonds between MA functionality of PP‐g‐MA and amine functional group of a‐MWNT. Higher tensile properties of PP/a‐MWNT/PP‐g‐MA composite fibers were registered with varying DR of the as‐spun fiber. Orientation factors of a‐MWNT and PP chains along the fiber axis were correlated with the higher tensile modulus and tensile strength of PP/a‐MWNT/PP‐g‐MA composite fiber of varying DR. Crystallization studies indicated the role of hetero‐nucleating action of a‐MWNT in PP/a‐MWNT/PP‐g‐MA composite fiber. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Effect of maleic anhydride grafted polypropylene on the mechanical and morphological properties of chemically modified short‐pineapple‐leaf‐fiber‐reinforced polypropylene composites

With the rising cost of petroleum‐based fibers, the utilization of plant fibers in the manufacture of polymer–matrix composites is gaining importance worldwide. The scope of this study was to examine the perspective of the use of pineapple leaf fibers (PALFs) as reinforcements for polypropylene (PP). These fibers are environmentally friendly, low‐cost byproducts of pineapple cultivation and are readily available in the northeastern region of India. Here, both untreated and treated pineapple fibers were used. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as a compatibilizing agent. The polymer matrix of PP was used to prepare composite specimens with different volume fractions (5–20%) of fibers by the addition of 5% of MA‐g‐PP. These specimens were tested for their mechanical properties, and additional assessments were made via observations by scanning electron microscopy, thermogravimetric analysis, and IR spectroscopy. Increase in the impact behavior, flexural properties, and tensile moduli of the composites were noticed, and these were more appreciable in the treated fibers mixed with MA‐g‐PP. PALF in 10 vol % in PP mixed with MA‐g‐PP was the optimum and recommended composition, where the flexural properties were the maximum. The impact strength and the tensile modulus were also considerably high. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

废旧三元乙丙橡胶粉改性聚丙烯的性能研究

采用废旧三元乙丙橡胶粉(简称WEPDM)对聚丙烯(PP)进行改性,并研究WEPDM用量对WEPDM/PP复合材料物理性能、熔体流动性、热稳定性以及微观结构的影响.结果表明:加入少量WEPDM可以使PP的综合物理性能提高;WEPDM用量为15份时,与纯PP相比,WEPDM/PP复合材料的拉伸强度、弯曲强度和拉断伸长率均得到提高,冲击强度变化不大;继续增大WEPDM用量可以大幅提高WEPDM/PP复合材料的冲击强度,但会导致拉伸强度和弯曲强度大幅降低.加入WEPDM会使WEPDM/PP复合材料的熔体流动性变差,但可以显著提高热稳定性;WEPDM用量为15～20份时,WEPDM与PP的相容性较好,两相结合较好,没有明显的界面区分.     

Injection molding of long sisal fiber–reinforced polypropylene: Effects of compatibilizer concentration and viscosity on fiber adhesion and thermal degradation

A two‐step process was used to obtain long sisal fiber‐polypropylene (SF/PP)–reinforced thermoplastic composites, using maleic anhydride grafted polypropylene (MA‐g‐PP) as a compatibilizer. At a first stage, modified polypropylenes (mPP) were used for an extrusion impregnation process, for the preparation of composite pellets containing about 70 wt% of SF. SF/mPP pellets with a large aspect ratio were prepared by continuous extrusion impregnation of a continuous SF yarn, using a single screw extruder and an adequate impregnation die. The mPP used were MA‐g‐PP and regular polypropylene (PP), modified by reaction with different amounts of an organic peroxide. The composite pellets were thus dry blended with regular PP pellets in an injection machine hopper, and injection molded to obtain composite tensile specimens with a minimum quantity of modified polypropylene, minimum fiber breakage and thermal degradation, and excellent mechanical properties. It is shown that the fiber breakage is reduced to a minimum, even for recycled composites, due to the presence of the low‐viscosity polymer layer wetting the SF fibers. The bulk composite effective viscosity and the fiber breakage extent and thermal degradation during the injection‐molding step are found to be closely related. Blending with much less expensive mPP at the impregnation stage optimizes the amount of expensive MA‐g‐PP. POLYM. ENG. SCI., 45:613–621, 2005. © 2005 Society of Plastics Engineers     

Study of polypropylene/ethylene‐propylene‐diene monomer blends reinforced with sisal fibers

Thermoplastics reinforced with natural fibers have attracted much attention from researchers because of their advantages, especially regarding environmental aspects. However, poor impact strength, particularly at low temperatures, limits the application of some thermoplastics, such as polypropylene (PP). To minimize this drawback, impact modifiers have been used, including the terpolymer of ethylene‐propylene‐diene (EPDM). In this work, PP/EPDM/sisal composites of distinct compositions were investigated focusing on the effect of the alkali (NaOH) treatment of the vegetable fiber on the composites properties regarding physical, mechanical, thermal, and morphological behavior. The results indicated that flow rate decreases at higher fiber content due to flow hindering by the presence of the fibers. The addition of the fiber, in general, increased Young's modulus and strength (tensile and flexural), whereas impact strength increased for higher EPDM content. The alkali treatment was considered generally efficient in terms of mechanical properties, even though this was not found in the dynamic mechanical analysis. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Long jute fiber‐reinforced polypropylene composite: Effects of jute fiber bundle and glass fiber hybridization

Two types of long jute fiber pellet consisting of twisted‐jute yarn (LFT‐JF/PP) and untwisted‐jute yarn (UT‐JF/PP) pellets are used to prepare jute fiber–reinforced polypropylene (JF/PP) composites. The mechanical properties of both long fiber composites are compared with that of re‐pelletized pellet (RP‐JF/PP) of LFT‐JF/PP pellet, which is re‐compounded by extrusion compounding. High stiffness and high impact strength of JF/PP composites are as a result of using long fiber. However, the longer fiber bundle consequently affects the distribution of jute fiber. The incorporation of 10 wt % glass fibers is found to improve mechanical properties of JF/PP composites. Increasing mechanical properties of hybrid composites is dependent on the type of JF/PP pellets, which directly affect the fiber length and fiber orientation of glass fiber within hybrid composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41819.