Primary sources and secondary formation of organic aerosols in beijing, china

Ambient aerosol samples were collected at an urban site and an upwind rural site of Beijing during the CAREBEIJING-2008 (Campaigns of Air quality REsearch in BEIJING and surrounding region) summer field campaign. Contributions of primary particles and secondary organic aerosols (SOA) were estimated by chemical mass balance (CMB) modeling and tracer-yield method. The apportioned primary and secondary sources explain 73.8% ± 9.7% and 79.6% ± 10.1% of the measured OC at the urban and rural sites, respectively. Secondary organic carbon (SOC) contributes to 32.5 ± 15.9% of the organic carbon (OC) at the urban site, with 17.4 ± 7.6% from toluene, 9.7 ± 5.4% from isoprene, 5.1 ± 2.0% from α-pinene, and 2.3 ± 1.7% from β-caryophyllene. At the rural site, the secondary sources are responsible for 38.4 ± 14.4% of the OC, with the contributions of 17.3 ± 6.9%, 13.9 ± 9.1%, 5.6 ± 1.9%, and 1.7 ± 1.0% from toluene, isoprene, α-pinene, and β-caryophyllene, respectively. Compared with other regions in the world, SOA in Beijing is less aged, but the concentrations are much higher; between the sites, SOA is more aged and affected by regional transport at the urban site. The high SOA loading in Beijing is probably attributed to the high regional SOC background (～2 μg m(-3)). The toluene SOC concentration is high and comparable at the two sites, implying that some anthropogenic components, at least toluene SOA, are widespread in Beijing and represents a major factor in affecting the regional air quality. The aerosol gaseous precursor concentrations and temperature correlate well with SOA, both affecting SOA formation. The significant SOA enhancement with increasing water uptake and acidification indicates that the aqueous-phase reactions are largely responsible SOA formation in Beijing.     

Secondary organic aerosol formation from intermediate-volatility organic compounds: cyclic, linear, and branched alkanes

Intermediate volatility organic compounds (IVOCs) are an important class of secondary organic aerosol (SOA) precursors that have not been traditionally included in chemical transport models. A challenge is that the vast majority of IVOCs cannot be speciated using traditional gas chromatography-based techniques; instead they are classified as an unresolved complex mixture (UCM) that is presumably made up of a complex mixture of branched and cyclic alkanes. To better understand SOA formation from IVOCs, a series of smog chamber experiments was conducted with different alkanes, including cyclic, branched, and linear compounds. The experiments focused on freshly formed SOA from hydroxyl (OH) radical-initiated reactions under high-NO(x) conditions at typical atmospheric organic aerosol concentrations (C(OA)). SOA yields from cyclic alkanes were comparable to yields from linear alkanes three to four carbons larger in size. For alkanes with equivalent carbon numbers, branched alkanes had the lowest SOA mass yields, ranging between 0.05 and 0.08 at a C(OA) of 15 μg m(-3). The SOA yield of branched alkanes also depends on the methyl branch position on the carbon backbone. High-resolution aerosol mass spectrometer data indicate that the SOA oxygen-to-carbon ratios were largely controlled by the carbon number of the precursor compound. Depending on the precursor size, the mass spectrum of SOA produced from IVOCs is similar to the semivolatile-oxygenated and hydrocarbon-like organic aerosol factors derived from ambient data. Using the new yield data, we estimated SOA formation potential from diesel exhaust and predict the contribution from UCM vapors to be nearly four times larger than the contribution from single-ring aromatics and comparable to that of polycyclic aromatic hydrocarbons after several hours of oxidation at typical atmospheric conditions. Therefore, SOA from IVOCs may be an important contributor to urban OA and should be included in SOA models; the yield data presented in this study are suitable for such use.     

Molecular size evolution of oligomers in organic aerosols collected in urban atmospheres and generated in a smog chamber

Only a minor fraction of the total organic aerosol mass can be resolved on a molecular level. High molecular weight compounds in organic aerosols have recently gained much attention because this class of compound potentially explains a major fraction of the unexplained organic aerosol mass. These compounds have been identified with different mass spectrometric methods, and compounds with molecular masses up to 1000 Da are found in secondary organic aerosols (SOA) generated from aromatic and terpene precursors in smog chamber experiments. Here, we apply matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) to SOA particles from two biogenic precursors, alpha-pinene and isoprene. Similar oligomer patterns are found in these two SOA systems, but also in SOA from trimethylbenzene, an anthropogenic SOA precursor. However, different maxima molecular sizes were measured for these three SOA systems. While oligomers in alpha-pinene and isoprene have sizes mostly below 600-700 Da, they grow up to about 1000 Da in trimethylbenzene-SOA. The final molecular size of the oligomers is reached early during the particle aging process, whereas other particle properties related to aging, such as the overall acid concentration or the oligomer concentration, increase continuously over a much longer time scale. This kinetic behavior of the oligomer molecular size growth can be explained by a chain growth kinetic regime. Similar oligomer mass patterns were measured in aqueous extracts of ambient aerosol samples (measured with the same technique). Distinct differences between summer and winter were observed. In summer a few single mass peaks were measured with much higher intensity than in winter, pointing to a possible difference in the formation processes of these compounds in winter and summer.     

A case study of urban particle acidity and its influence on secondary organic aerosol

Size-resolved indicators of aerosol acidity, including H+ ion concentrations (H+Aer) and the ratio of stoichiometric neutralization are evaluated in submicrometer aerosols using highly time-resolved aerosol mass spectrometer (AMS) data from Pittsburgh. The pH and ionic strength within the aqueous particle phase are also estimated using the Aerosol Inorganics Model (AIM). Different mechanisms that contribute to the presence of acidic particles in Pittsburgh are discussed. The largest H+Aer loadings and lowest levels of stoichiometric neutralization were detected when PM1 loadings were high and dominated by SO4(2-). The average size distribution of H+Aer loading shows an accumulation mode at Dva approximately 600 nm and an enhanced smaller mode that centers at Dva approximately 200 nm and tails into smaller sizes. The acidity in the accumulation mode particles suggests that there is generally not enough gas-phase NH3 available on a regional scale to completely neutralize sulfate in Pittsburgh. The lack of stoichiometric neutralization in the 200 nm mode particles is likely caused by the relatively slow mixing of gas-phase NH3 into SO2-rich plumes containing younger particles. We examined the influence of particle acidity on secondary organic aerosol (SOA) formation by comparing the mass concentrations and size distributions of oxygenated organic aerosol (00A--surrogate for SOA in Pittsburgh) during periods when particles are, on average, acidic to those when particles are bulk neutralized. The average mass concentration of ODA during the acidic periods (3.1 +/- 1.7 microg m(-3)) is higher than that during the neutralized periods (2.5 +/- 1.3 microg m(-3)). Possible reasons for this enhancement include increased condensation of SOA species, acid-catalyzed SOA formation, and/or differences in air mass transport and history. However, even if the entire enhancement (approximately 0.6 microg m(-3)) can be attributed to acid catalysis, the upperbound increase of SOA mass in acidic particles is approximately 25%, an enhancement that is much more moderate than the multifold increases in SOA mass observed during some lab studies and inferred in SO2-rich industrial plumes. In addition, the mass spectra of OOA from these two periods are almost identical with no discernible increase in relative signal intensity at larger m/z's (>200 amu), suggesting that the chemical nature of SOA is similar during acidic and neutralized periods and that there is no significant enhancement of SOA oligomer formation during acidic particle periods in Pittsburgh.     

Measurements of isoprene-derived organosulfates in ambient aerosols by aerosol time-of-flight mass spectrometry-part 2: temporal variability and formation mechanisms

Organosulfate species have recently gained attention for their potentially significant contribution to secondary organic aerosol (SOA); however, their temporal behavior in the ambient atmosphere has not been probed in detail. In this work, organosulfates derived from isoprene were observed in single particle mass spectra in Atlanta, GA during the 2002 Aerosol Nucleation and Characterization Experiment (ANARChE) and the 2008 August Mini-Intensive Gas and Aerosol Study (AMIGAS). Real-time measurements revealed that the highest organosulfate concentrations occurred at night under a stable boundary layer, suggesting gas-to-particle partitioning and subsequent aqueous-phase processing of the organic precursors played key roles in their formation. Further analysis of the diurnal profile suggests possible contributions from multiple production mechanisms, including acid-catalysis and radical-initiation. This work highlights the potential for additional SOA formation pathways in biogenically influenced urban regions to enhance the organic aerosol burden.     

Contrasting diurnal variations in fossil and nonfossil secondary organic aerosol in urban outflow, Japan

Diurnal variations of fossil secondary organic carbon (SOC) and nonfossil SOC were determined for the first time using a combination of several carbonaceous aerosol measurement techniques, including radiocarbon (1?C) determinations by accelerator mass spectrometry, and a receptor model (chemical mass balance, CMB) at a site downwind of Tokyo during the summer of 2007. Fossil SOC showed distinct diurnal variation with a maximum during daytime, whereas diurnal variation of nonfossil SOC was relatively small. This behavior was reproduced by a chemical transport model (CTM). However, the CTM underestimated the concentration of anthropogenic secondary organic aerosol (ASOA) by a factor of 4-7, suggesting that ASOA enhancement during daytime is not explained by production from volatile organic compounds that are traditionally considered major ASOA precursors. This result suggests that unidentified semivolatile organic compounds or multiphase chemistry may contribute largely to ASOA production. As our knowledge of production pathways of secondary organic aerosol (SOA) is still limited, diurnal variations of fossil and nonfossil SOC in our estimate give an important experimental constraint for future development of SOA models.     

Semicontinuous measurements of organic carbon and acidity during the Pittsburgh Air Quality Study: implications for acid-catalyzed organic aerosol formation

Laboratory evidence suggests that inorganic acid seed particles may increase secondary organic aerosol yields secondary organic aerosol (SOA) through heterogeneous chemistry. Additional laboratory studies, however, report that organic acidity generated in the same photochemical process by which SOA is formed may be sufficient to catalyze these heterogeneous reactions. Understanding the interaction between inorganic acidity and SOA mass is important when evaluating emission controls to meet PM2.5 regulations. We examine semicontinuous measurements of organic carbon (OC), elemental carbon (EC), and inorganic species from the Pittsburgh Air Quality Study to determine if we can detect coupling in the variations of inorganic acidity and OC. We were not able to detect significant enhancements of SOA production due to inorganic acidity in Western Pennsylvania most of the time, but its signal might have been lost in the noise. If we assume a causal relationship between inorganic acidity and OC, reductions in OC for Western Pennsylvania that might result from drastic reductions in inorganic acidity were estimated to be 2 +/- 4% by a regression technique, and an upper bound for this geographic area was estimated to be 5 +/- 8% based on calculations from laboratory measurements.     

Using proton transfer reaction mass spectrometry for online analysis of secondary organic aerosols

Proton-transfer-reaction mass spectrometry (PTR-MS) is a useful tool in ambient trace gas analysis, especially for the analysis of oxygenated volatile organic compounds (OVOC). Many OVOCs are produced during photooxidation of volatile organic compounds and contribute to both the gas phase and secondary organic aerosols (SOA). The inlet system of the PTR-MS instrument was modified to allow also for the measurement of the particulate phase of an aerosol with a high time resolution. The new inlet consists mainly of a denuder to strip off the gas phase, and a heater (120/150 degrees C) to vaporize the aerosol particles. This inlet system was tested with pinonic acid particles generated with a nebulizer and SOA particles formed during the photooxidation of 1,3,5-trimethylbenzene and alpha-pinene with NO(x) in a smog chamber. The performance of this new technique is discussed and the partitioning coefficients for the oxidation products are estimated.     

Source apportionment of PM2.5 in the Southeastern United States using solvent-extractable organic compounds as tracers

A chemical mass balance (CMB) receptor model using particle-phase organic compounds as tracers is applied to apportion the primary source contributions to fine particulate matter and fine particulate organic carbon concentrations in the southeastern United States to determine the seasonal variability of these concentrations. Source contributions to particles with aerodynamic diameter < or =2.5 microm (PM2.5) collected from four urban and four rural/suburban sites in AL, FL, GA, and MS during April, July, and October 1999 and January 2000 are calculated and presented. Organic compounds in monthly composite samples at each site are identified and quantified by gas chromatography/mass spectrometry and are used as molecular markers in the CMB model. The major contributors to identified PM2.5 organic carbon concentrations at these sites in the southeastern United States include wood combustion (25-66%), diesel exhaust (14-30%), meat cooking (5-12%), and gasoline-powered motor vehicle exhaust (0-10%), as well as smaller but statistically significant contributions from natural gas combustion, paved road dust, and vegetative detritus. The primary sources determined in the present study when added to secondary aerosol formation account for on average 89% of PM2.5 mass concentrations, with the major contributors to PM2.5 mass as secondary sulfate (30+/-6%), wood combustion (15+/-12%), diesel exhaust (16+/-7%), secondary ammonium (8+/-2%), secondary nitrate (4+/-3%), meat cooking (3+/-2%), gasoline-powered motor vehicle exhaust (2+/-2%), and road dust (2+/-2%). Distinct seasonality is observed in source contributions, including higher contributions from wood combustion during the colder months of October and January. In addition, higher percentages of unexplained fine organic carbon concentrations are observed in July, which are likely due to an increase in secondary organic aerosol formation during the summer season.     

O/C and OM/OC ratios of primary, secondary, and ambient organic aerosols with high-resolution time-of-flight aerosol mass spectrometry

A recently developed method to rapidly quantify the elemental composition of bulk organic aerosols (OA) using a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) is improved and applied to ambient measurements. Atomic oxygen-to-carbon (O/C) ratios characterize the oxidation state of OA, and O/C from ambient urban OA ranges from 0.2 to 0.8 with a diurnal cycle that decreases with primary emissions and increases because of photochemical processing and secondary OA (SOA) production. Regional O/C approaches approximately 0.9. The hydrogen-to-carbon (H/C, 1.4--1.9) urban diurnal profile increases with primary OA (POA) as does the nitrogen-to-carbon (N/C, approximately 0.02). Ambient organic-mass-to-organic-carbon ratios (OM/OC) are directly quantified and correlate well with O/C (R2 = 0.997) for ambient OA because of low N/C. Ambient O/C and OM/OC have values consistent with those recently reported from other techniques. Positive matrix factorization applied to ambient OA identifies factors with distinct O/C and OM/OC trends. The highest O/C and OM/OC (1.0 and 2.5, respectively) are observed for aged ambient oxygenated OA, significantly exceeding values for traditional chamber SOA,while laboratory-produced primary biomass burning OA (BBOA) is similar to ambient BBOA, O/C of 0.3--0.4. Hydrocarbon-like OA (HOA), a surrogate for urban combustion POA, has the lowest O/C (0.06--0.10), similar to vehicle exhaust. An approximation for predicting O/C from unit mass resolution data is also presented.     

Identification of the mass spectral signature of organic aerosols from wood burning emissions

Throughout the winter months, the village of Roveredo, Switzerland, frequently experiences strong temperature inversions that contribute to elevated levels of particulate matter. Wood is used as fuel for 75% of the domestic heating installations in Roveredo, which makes it a suitable location to study wood burning emissions in the atmosphere in winter. An Aerodyne quadrupole aerosol mass spectrometer (Q-AMS) was used to characterize the composition of the submicrometer, non-refractory aerosol particles at this location during two field campaigns in March and December 2005. Wood burning was found to be a major source of aerosols at this location in winter. Organics dominated the composition of the aerosols from this source, contributing up to 85% of the total AMS measured mass during the afternoon and evening hours. Carbonaceous particle analysis showed that organic carbon composed up to 86% of the total carbon mass collected at evening times. Results from 14C isotope determination revealed that up to 94% of the organic mass came from non-fossil sources, which can be attributed mostlyto wood burning. The unique combination of off-line 14C isotope analysis and on-line aerosol mass spectrometry was used to identify periods during which organic mass was mainly from wood burning emissions and allowed for the identification of the AMS spectral signature of this source in the atmosphere. The identified ambient signature of wood burning was found to be very similar to the mass spectral signature obtained during the burning of chestnut wood samples in a small stove and also to the spectrum of levoglucosan. Particles from wood burning appeared to be composed of highly oxygenated organic compounds, and mass fragments 60, 73, and 137 have been suggested as marker fragments for wood burning aerosols. Mass fragment 44, which is used as a marker for oxygenated organic aerosols (OOA), contributed about 5% to the total organic signal from primary wood burning sources. The ratio of the organic mass emitted from wood burning to m/z 60 in Roveredo is 36. This ratio may be used to provide an estimate of the organic aerosol mass emitted from wood burning in other locations.     

Aircraft measurement of organic aerosols over China

Lower to middle (0.5-3.0 km altitude) tropospheric aerosols (PM2.5) collected by aircraft over inland and east coastal China were, for the first time, characterized for organic molecular compositions to understand anthropogenic, natural, and photochemical contribution to the air quality. n-Alkanes, fatty acids, sugars, polyacids are detected as major compound classes, whereas lignin and resin products, sterols, polycyclic aromatic hydrocarbons, and phthalic acids are minor species. Average concentrations of all the identified compounds excluding malic acid correspond to 40-50% of those reported on the ground sites. Relative abundances of secondary organic aerosol (SOA) components such as malic acid are much higher in the aircraft samples, suggesting an enhanced photochemical production over China. Organic carbon (OC) concentrations in summer (average, 24.3 microg m(-3)) were equivalent to those reported on the ground sites. Higher OC/EC (elemental carbon) ratios in the summer aircraft samples also support a significant production of SOA over China. High loadings of organic aerosols in the Chinese troposphere may be responsible to an intercontinental transport of the pollutants and potential impact on the regional and global climate changes.     

The effect of solvent on the analysis of secondary organic aerosol using electrospray ionization mass spectrometry

This study examined the effect of solvent on the analysis of organic aerosol extracts using electrospray ionization mass spectrometry (ESI-MS). Secondary organic aerosol (SOA) produced by ozonation of d-limonene, as well as several organic molecules with functional groups typical for OA constituents, were extracted in methanol, d3-methanol, acetonitrile, and d3-acetonitrile to investigate the extent and relative rates of reactions between analyte and solvent. High resolution ESI-MS showed that reactions of carbonyls with methanol produce significant amounts of hemiacetals and acetals on time scales ranging from several minutes to several days, with the reaction rates increasing in acidified solutions. Carboxylic acid groups were observed to react with methanol resulting in the formation of esters. In contrast acetonitrile extracts showed no evidence of reactions with analyte molecules, suggesting that acetonitrile is the preferred solvent for SOA extraction. The use of solvent-analyte reactivity as a tool for the improved characterization of functional groups in complex organic mixtures was demonstrated. Direct comparison between mass spectra of the same SOA samples extracted in methanol versus acetonitrile was used to estimate the lower limits for the relative fractions of carbonyls (> or = 42%) and carboxylic acids (> or = 55%) in d-limonene SOA.     

Effect of hydrophilic organic seed aerosols on secondary organic aerosol formation from ozonolysis of α-pinene

Gas-particle partitioning theory is widely used in atmospheric models to predict organic aerosol loadings. This theory predicts that secondary organic aerosol (SOA) yield of an oxidized volatile organic compound product will increase as the mass loading of preexisting organic aerosol increases. In a previous work, we showed that the presence of model hydrophobic primary organic aerosol (POA) had no detectable effect on the SOA yields from ozonolysis of α-pinene, suggesting that the condensing SOA compounds form a separate phase from the preexisting POA. However, a substantial faction of atmospheric aerosol is composed of polar, hydrophilic organic compounds. In this work, we investigate the effects of model hydrophilic organic aerosol (OA) species such as fulvic acid, adipic acid, and citric acid on the gas-particle partitioning of SOA from α-pinene ozonolysis. The results show that only citric acid seed significantly enhances the absorption of α-pinene SOA into the particle-phase. The other two seed particles have a negligible effect on the α-pinene SOA yields, suggesting that α-pinene SOA forms a well-mixed organic aerosol phase with citric acid and a separate phase with adipic acid and fulvic acid. This finding highlights the need to improve the thermodynamics treatment of organics in current aerosol models that simply lump all hydrophilic organic species into a single phase, thereby potentially introducing an erroneous sensitivity of SOA mass to emitted OA species.     

Impact of the hydrocarbon to NOx ratio on secondary organic aerosol formation

A series of m-xylene/NOx experiments were conducted in the new Bourns College of Engineering-Center for Environmental Research and Technology dual 90 m3 indoor smog chamber to elucidate the role of NOx on the secondary organic aerosol (SOA) formation potential of m-xylene. The results presented herein demonstrate a clear dependence of m-xylene SOA formation potential on NOx, particularly at atmospherically relevant organic aerosol concentration. Experiments with lower NOx levels generated considerably more organic aerosol mass than did experiments with higher NOx levels when reacted m-xylene was held constant. For example, SOA formation from approximately 150 microg m(-3) reacted m-xylene produced 0.6-9.3 microg m(-3) aerosol mass for NOx concentrations ranging from 286 to 10 ppb. The increase in SOA formation was not attributable to changes in ozone and nitrate concentration. A general discussion about possible influences of NOx on SOA formation for this system is included.     

NMR determination of total carbonyls and carboxyls: a tool for tracing the evolution of atmospheric oxidized organic aerosols

Nuclear magnetic resonance (NMR) spectroscopy is used to investigate the chemical composition of organic aerosol in terms of functional group distribution with a special focus on secondary organic aerosol (SOA) formation. The knowledge of the functional group composition is a benchmark for understanding how SOA components partition into the particulate phase and undergo chemical transformation. The paper presents a new chemical derivatization procedure coupled to proton NMR (1H NMR) analysis for the specific determination of total carbonylic groups in atmospheric aerosol samples, which couples with the procedure for determination of total carboxylic acid groups described in a previous work. A first deployment of the combined techniques for the analysis of PM10 samples collected in the Po Valley in the warm season shows that the concentration in the particulate phase of total carbonyls varies and covaries with respect to those of carboxylic acids and of less-oxidized functional groups. The proposed methodology provides the breakdown of the oxygenated fraction of the organic aerosol into major functional groups through well-established chemical methods and can be used to benchmark the more sensitive and widely used aerosol mass spectrometric techniques.     

Effect of acidity on secondary organic aerosol formation from isoprene

The effect of particle-phase acidity on secondary organic aerosol (SOA) formation from isoprene is investigated in a laboratory chamber study, in which the acidity of the inorganic seed aerosol was controlled systematically. The observed enhancement in SOA mass concentration is closely correlated to increasing aerosol acidity (R2 = 0.979). Direct chemical evidence for acid-catalyzed particle-phase reactions was obtained from the SOA chemical analyses. Aerosol mass concentrations for the 2-methyltetrols, as well as the newly identified sulfate esters, both of which serve as tracers for isoprene SOA in ambient aerosols, increased significantly with enhanced aerosol acidity. Aerosol acidities, as measured in nmol of H+ m(-3), employed in the present study are in the same range as those observed in tropospheric aerosol collected from the eastern U.S.     

Contribution of first- versus second-generation products to secondary organic aerosols formed in the oxidation of biogenic hydrocarbons

Biogenic hydrocarbons emitted by vegetation are important contributors to secondary organic aerosol (SOA), but the aerosol formation mechanisms are incompletely understood. In this study, the formation of aerosols and gas-phase products from the ozonolysis and photooxidation of a series of biogenic hydrocarbons (isoprene, 8 monoterpenes, 4 sesquiterpenes, and 3 oxygenated terpenes) are examined. By comparing aerosol growth (measured by Differential Mobility Analyzers, DMAs) and gas-phase concentrations (monitored by a Proton Transfer Reaction Mass Spectrometer, PTR-MS), we study the general mechanisms of SOA formation. Aerosol growth data are presented in terms of a "growth curve", a plot of aerosol mass formed versus the amount of hydrocarbon reacted. From the shapes of the growth curves, it is found that all the hydrocarbons studied can be classified into two groups based entirely on the number of double bonds of the hydrocarbon, regardless of the reaction systems (ozonolysis or photooxidation) and the types of hydrocarbons studied: compounds with only one double bond and compounds with more than one double bond. For compounds with only one double bond, the first oxidation step is rate-limiting, and aerosols are formed mainly from low volatility first-generation oxidation products; whereas for compounds with more than one double bond, the second oxidation step may also be rate-limiting and second-generation products contribute substantially to SOA growth. This behavior is characterized by a vertical section in the growth curve, in which continued aerosol growth is observed even after all the parent hydrocarbon is consumed.     

Aqueous-phase secondary organic aerosol and organosulfate formation in atmospheric aerosols: a modeling study

We have examined aqueous-phase secondary organic aerosol (SOA) and organosulfate (OS) formation in atmospheric aerosols using a photochemical box model with coupled gas-phase chemistry and detailed aqueous aerosol chemistry. SOA formation in deliquesced ammonium sulfate aerosol is highest under low-NO(x) conditions, with acidic aerosol (pH = 1) and low ambient relative humidity (40%). Under these conditions, with an initial sulfate loading of 4.0 μg m(-3), 0.9 μg m(-3) SOA is predicted after 12 h. Low-NO(x) aqueous-aerosol SOA (aaSOA) and OS formation is dominated by isoprene-derived epoxydiol (IEPOX) pathways; 69% or more of aaSOA is composed of IEPOX, 2-methyltetrol, and 2-methyltetrol sulfate ester. 2-Methyltetrol sulfate ester comprises >99% of OS mass (66 ng m(-3) at 40% RH and pH 1). In urban (high-NO(x)) environments, aaSOA is primarily formed via reversible glyoxal uptake, with 0.12 μg m(-3) formed after 12 h at 80% RH, with 20 μg m(-3) initial sulfate. OS formation under all conditions studied is maximum at low pH and lower relative humidities (<60% RH), i.e., when the aerosol is more concentrated. Therefore, OS species are expected to be good tracer compounds for aqueous aerosol-phase chemistry (vs cloudwater processing).     

Estimated effects of composition on secondary organic aerosol mass concentrations

The composition dependence of secondary organic aerosol (SOA) mass concentrations is explored using an absorptive partitioning model under a variety of simplified atmospheric conditions. A thermodynamic model based on the Wilson equation is used to estimate activity coefficients for mixtures containing primary organics, secondary organics, and water. Changes in the mean molecular weight of the absorbing aerosol mixture due to the presence of water are also accounted for. Model simulations use semivolatile and primary organic components with differing affinities for each other and for water. Results suggest that aerosol composition has an effect on SOA levels that is significant and comparable in magnitude to those due to diurnal temperature variations and semivolatile precursor emission rates. For dissimilar organic components at zero relative humidity, predicted peak SOA mass concentrations are reduced up to 45%. Under low and high relative humidity conditions, SOA levels increase by 3-41% and 11-130%, respectively, depending on the hydrophobicity of the organic components, with maximum concentrations at night when humidity is highest Effects are most pronounced for relatively volatile components that are most sensitive to shifts in the amount and type of absorbing aerosol.