Effect of β-lactoglobulin A and B whey protein variants on cheese yield potential of a model milk system

Cheese yield mainly depends on the amount and proportion of milk constituents; however, genetic variants of the proteins present in milk may also have an important effect. The objective of this research was to study the effect of the variants A and B of β-lactoglobulin (LG) on cheese yield using a model system consisting of skim milk powder fortified with different levels of a mixture containing α-lactalbumin and β-LG genetic variants (A, B, or A-B) in a 1:2 ratio. Fortified milk samples were subjected to pasteurization at 65°C for 30 min. Miniature cheeses were made by acidifying (pH = 5.9) fortified milk and incubating with rennet for 1 h at 32°C. The clot formed was cut, centrifuged at 2,600 × g for 30 min at 20°C and drained for determining cheese yield. Cheese-yielding capacity was expressed as actual yield (grams of cheese curd per 100 g of milk) and dry weight yield (grams of dried cheese curd per 100 g of milk). Free-zone capillary electrophoresis was used for determining β-LG A or B recovery in the curd during rennet-induced coagulation. The presence of β-LG variant B resulted in a significantly higher actual and dried weight cheese yield than when A or A-B were present at levels ≤0.675% of whey protein (WP) addition. Results of free-zone capillary electrophoresis allowed us to infer that β-LG B associates with the casein micelles during renneting, as shown by an increase in the recovery of this variant in the curd when β-LG B was added up to a maximum at 0.45% (equivalent to 0.675% WP). In general, actual or dried weight cheese yield increased as WP addition was increased from 0.225 to 0.675%. However, when WP addition ranged from 0.675 to 0.90%, a drastic drop in cheese yield was observed. This behavior may be because an increase in the aggregation of casein micelles with a concomitant inclusion of whey protein in the gel occurs at low levels of WP addition, whereas once the association of WP with the casein micelles reach a saturation point at addition levels higher than 0.675%, rearrangements of the gel network result in larger whey expulsion and syneresis. This knowledge is expected to be useful to maximize cheese yield and optimize processing conditions during cheese and cheese analogs manufacturing.     

Interactions between β-lactoglobulin and dextran sulfate at near neutral pH and their effect on thermal stability

The effect of interactions between β-lactoglobulin (β-LG) and dextran sulfate (DS) on thermal stability at near neutral pH was investigated. Samples containing 6% w/w β-LG and DS (M_w = 5–500 kDa) at different biopolymer weight ratios, pH (5.6–6.2), and NaCl concentrations (0–30 mM) were heated at 85 °C for 15 min. Turbidity results showed that the presence of DS at appropriate biopolymer weight ratio and pH significantly lowered the turbidity of heated β-LG. Solutions containing DS:β-LG weight ratios of 0.02 or less showed improved heat stability as indicated by decreased turbidity. Analysis of the unheated mixture by size exclusion chromatography coupled with multi-angle laser light scattering (SEC–MALLS) showed an interaction between β-LG and DS. The size of the aggregates increased as pH decreased. The β-LG–DS aggregates had a greater negative charge as seen from electrophoretic mobility measurement. Addition of 30 mM NaCl inhibited complex formation and the effect of DS on reducing the turbidity of heated β-LG, suggesting that the interaction was electrostatic in nature. Other than charge property, the amount and size of native aggregates appeared to be the major factor in determining how DS altered heat-induced aggregation. The presence of DS decreased denaturation temperature of β-LG, indicating that DS did not improve thermal stability of β-LG by stabilizing its native state but rather by altering its aggregation. The results provide information that will facilitate the application of whey proteins and polysaccharides as functional ingredients in foods and beverages.     

Effect of heating on the distribution of transforming growth factor-��2 in bovine milk

The objective of this study was to characterize the impact of heat treatments on the distribution of transforming growth factor-beta (TGF-??2) between cream and skim milk and between the casein and whey fractions of skim milk. Skimming removed 45% and 62% of the TGF-??2 from raw and pasteurized milks and only 8% of the total TGF-??2 in skimmed pasteurized milk was found in whey, compared to 37% in whey from raw skimmed milk. The TGF-??2 content of whey decreased as the heat treatment of the milk increased in intensity (thermization > pasteurization > UHT sterilization). Using milk held for 1 or 2 min at temperatures ranging from 57 to 84 °C, it was shown that TGF-??2 in the whey portion decreases at temperatures above 66 °C and becomes undetectable at temperatures higher than 76 °C. Altogether, these data on the heat-induced changes in TGF-??2 content of cream, skim milk, casein and whey reveal a potentially negative impact of certain heat treatments in developing TGF-??2-enriched fractions from milk.     

Effect of milk solids concentration on the gels formed by the acidification of heated pH-adjusted skim milk

Reconstituted skim milk of 10–25% total solids was adjusted to pH values between about 6.2 and 7.1 and heated at 80 °C for 30 min. Gels were formed from the heated milks by slow acidification to pH 4.2 and the gelation process and final gels were analyzed for their rheological properties. At each milk concentration, the final acid gel firmness (final G′) and breaking stress could be changed markedly by manipulation of the pH during heating. The final gel firmness and breaking stress could also be modified by changing the concentration of the milk solids prior to heating and acidification. The results indicated that similar gel firmness and breaking stress could be achieved over a range of milk concentrations by control of the pH of the milk during heating. When expressed as a percentage change in final G′ or breaking stress relative to that obtained at the natural pH, plots of the change in final G′ or breaking stress versus pH fell close to a single curve, indicating that the same mechanism may influence the gelation properties at all milk concentrations. The final G′ and breaking stress were related to the denaturation and interaction of the whey proteins with the casein micelles, and the formation of non-sedimentable casein when the milk was heated.     

Diffusing-wave spectroscopy investigation of heated reconstituted skim milks containing calcium chloride

The effect of heat treatment on reconstituted 10 wt% skim milks containing up to 20 mM added CaCl₂ at different pH values (pH 6.0–7.2), was investigated both in situ and after cooling of the heat treated milks. Measurements of pH in situ showed that pH decreased at high temperature, that the decrease in pH increases with the increase in the initial pH and that the magnitude of the decrease in pH was greater for milks with added CaCl₂. Marked increases in the viscosity at 25 °C of heated milks indicated that milks without added CaCl₂ with initial pH ≤6.2 and milks with 10 mM added CaCl₂ with initial pH ≤6.4, heated at 90 °C were not heat stable. At a given heating temperature, it was possible to superimpose the measured viscosity of samples with or without added CaCl₂ on the same curve when these were plotted as a function of the pH at that temperature instead of the initial milk temperature. To further demonstrate this finding a DWS experimental set-up was built and in situ measurements were performed on the milk samples heated at 75 °C for 10 min. The DWS measurements showed that ηa, the product of the viscosity with particle size, can also be superimposed for all the measured samples, when plotted as a function of the pH at the heating temperatures. Both the viscosity and DWS data demonstrate the importance of the pH at the heating-temperatures in influencing heat-induced changes in milk.     

Short communication: Effect of kefir grains on proteolysis of major milk proteins

The effect of kefir grains on the proteolysis of major milk proteins in milk kefir and in a culture of kefir grains in pasteurized cheese whey was followed by reverse phase-HPLC analysis. The reduction of κ-, α-, and β-caseins (CN), α-lactalbumin (α-LA), and β-lactoglobulin (β-LG) contents during 48 and 90 h of incubation of pasteurized milk (100 mL) and respective cheese whey with kefir grains (6 and 12 g) at 20°C was monitored. Significant proteolysis of α-LA and κ-, α-, and β-caseins was observed. The effect of kefir amount (6 and 12 g/100 mL) was significant for α-LA and α- and β-CN. α-Lactalbumin and β-CN were more easily hydrolyzed than α-CN. No significant reduction was observed with respect to β-LG concentration for 6 and 12 g of kefir in 100 mL of milk over 48 h, indicating that no significant proteolysis was carried out. Similar results were observed when the experiment was conducted over 90 h. Regarding the cheese whey kefir samples, similar behavior was observed for the proteolysis of α-LA and β-LG: α-LA was hydrolyzed between 60 and 90% after 12 h (for 6 and 12 g of kefir) and no significant β-LG proteolysis occurred. The proteolytic activity of lactic acid bacteria and yeasts in kefir community was evaluated. Kefir milk prepared under normal conditions contained peptides from proteolysis of α-LA and κ-, α-, and β-caseins. Hydrolysis is dependent on the kefir:milk ratio and incubation time. β-Lactoglobulin is not hydrolyzed even when higher hydrolysis time is used. Kefir grains are not appropriate as adjunct cultures to increase β-LG digestibility in whey-based or whey-containing foods.     

Study of the acid and thermal stability of β-lactoglobulin–ligand complexes using fluorescence quenching

The major protein in bovine milk whey, β-lactoglobulin (β-LG), has several binding sites for ligands. Its interactions with folic acid (a hydrophilic compound), resveratrol (amphiphilic) and α-tocopherol (hydrophobic) at neutral and acidic pH and after heating to 85 °C were studied using fluorescence quenching. Binding of folic acid occurs in a hydrophobic pocket in the groove between the α-helix and the β-barrel and is disturbed by decreasing the pH from 7.0 to 2.0. Resveratrol binds to the outer surface of β-LG near Trp19–Arg124 to form complexes that are stable at acidic pH. Acidification caused the release of α-tocopherol bound to the internal cavity but had no influence on that bound to a site at the surface of β-LG. The β-LG/folic acid complex was thermally stable. Thermal denaturing improved the affinity of the protein for resveratrol but decreased somewhat its affinity for α-tocopherol. These results should help guide the development of formulations based on β-LG as a carrier of a wide range of bioactive nutrients.     

Comparative Study on Heat Stability and Functionality of Camel and Bovine Milk Whey Proteins

Heat stability, emulsifying, and foaming properties of camel whey have been investigated and compared with that of bovine whey. Camel whey is similar to bovine whey in composition, but is deficient in β-lactoglubulin (β-LG), a major component of bovine whey. Whether the deficiency in β-LG will affect stability and functional properties is not yet known. Substantial information on the functional properties of bovine milk whey proteins is available; however, there is little research done on functional properties of camel whey proteins. Therefore, the objective of this study was to investigate the heat stability, emulsifying, and foaming characteristics of camel whey proteins. Calorimetric studies showed no significant difference in heat stability between bovine and camel whey proteins in liquid form. Upon drying, thermograms indicated that the 2 proteins are different in composition and thermal stability. The difference is represented in the absence of β-LG and the occurrence of protein denaturation peak at a lesser temperature in camel whey. The first marginal thermal transition in bovine whey appeared at 81°C, followed by 2 other transitions at 146 and 198°C. For camel whey, the transitions appeared at 139, 180, and 207°C respectively. The first marginal denaturation peak in bovine whey is due to β-LG, which is essentially absent in camel whey, while the second peak is due to the mixture of α-lactalbumin, serum albumin, and possibly part of the partially stabilized β-LG structure during the denaturation process. Because camel whey is deficient in β-LG, the denaturation peak at 139 must be due to the mixture of α-lactalbumin and camel serum albumin. In both proteins, the highest thermal transition is due to sugars such as lactose. The solubility study has shown that camel whey is more sensitive to pH than bovine milk whey and that heat stability is lowest near the isoelectric point of the proteins at pH 4.5. The sensitivity to pH resulted in partial denaturation and increased tendency to aggregate, which caused poor and unstable emulsion at pH 5. Both bovine and camel whey proteins have demonstrated good foaming properties; however, the magnitudes of these properties were considerably greater in bovine milk for all of the conditions studied.     

The effect of high pressure-low temperature treatment on physicochemical properties in milk

This study was carried out to investigate the effect of high pressure-low temperature (HPLT) treatment on physicochemical properties and nutrients in milk. The milk was treated at 200 MPa and −4°C for 10, 20, and 30 min. Protease and lipase activities of HPLT-treated milk were highly inactivated compared with that of raw milk. Among time treatments, the 30-min treatment showed the lowest activities compared with others. Absorbance of thiobarbituric acid increased with time in HLPT-treated milks; however, no difference was observed between the raw milk and milk treated for 10 min. The concentrations of short-chain fatty acids except C₄ in HPLT-treated milks increased with time. The total free amino acids in HPLT-treated milks were greater than that of the raw milk for the 30-min treatment. l-Ascorbic acid, niacin, and riboflavin in HPLT-treated milks were significantly lower compared with concentrations in raw milk. For color, the L-value of HPLT-treated milks was significantly lower than that of the raw milk; however, there was no difference in the a-value for 10 min and in the b-value at 20 min between the raw milk and the HPLT-treated milks.     

Effect of moderate inlet temperatures in ultra-high-pressure homogenization treatments on physicochemical and sensory characteristics of milk

The effect of ultra-high-pressure homogenization (UHPH) on raw whole milk (3.5% fat) was evaluated to obtain processing conditions for the sterilization of milk. Ultra-high-pressure homogenization treatments of 200 and 300 MPa at inlet temperatures (Ti) of 55, 65, 75, and 85°C were compared with a UHT treatment (138°C for 4 s) in terms of microbial inactivation, particle size and microstructure, viscosity, color, buffering capacity, ethanol stability, propensity to proteolysis, and sensory evaluation. The UHPH-treated milks presented a high level of microbial reduction, under the detection limit, for treatments at 300 MPa with Ti of 55, 65, 75, and 85°C, and at 200 MPa with Ti = 85°C, and few survivors in milks treated at 200 MPa with Ti of 55, 65, and 75°C. Furthermore, UHPH treatments performed at 300 MPa with Ti = 75 and 85°C produced sterile milk after sample incubation (30 and 45°C), obtaining similar or better characteristics than UHT milk in color, particle size, viscosity, buffer capacity, ethanol stability, propensity to protein hydrolysis, and lower scores in sensory evaluation for cooked flavor.     

Effect of pH at heat treatment on the hydrolysis of κ-casein and the gelation of skim milk by chymosin

Skim milk was adjusted to pH values between 6.5 and 7.1 and heated at 90 °C for times from 0 to 30 min. After heat treatment, the samples were re-adjusted to the natural pH (pH 6.67) and allowed to re-equilibrate. High levels of denatured whey proteins associated with the casein micelles during heating at pH 6.5 (about 70-80% of the total after 30 min of heating). This level decreased as the pH at heating was increased, so that about 30%, 20% and 10% of the denatured whey protein was associated with the casein micelles after 30 min of heating at pH 6.7, 6.9 and 7.1, respectively. Increasing levels of κ-casein were transferred to the serum as the pH at heating was increased. The loss of κ-casein and the formation of para-κ-casein with time as a consequence of the chymosin treatment of the milk samples were monitored by sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE). The loss of κ-casein and the formation of para-κ-casein were similar for the unheated and heated samples, regardless of the pH at heating or the heat treatment applied. Monitoring the gelation properties with time for the chymosin-treated milk samples indicated that the heat treatment of the milk markedly increased the gelation time and decreased the firmness (G^′) of the gels formed, regardless of whether the denatured whey proteins were associated with the casein micelles or in the milk serum. There was no effect of pH at heat treatment. These results suggest that the heat treatment of milk has only a small effect on the primary stage of the chymosin reaction (enzymatic phase). However, heat treatment has a marked effect on the secondary stage of this reaction (aggregation phase), and the effect is similar regardless of whether the denatured whey proteins are associated with the casein micelles or in the milk serum as nonsedimentable aggregates.     

The physicochemical parameters during dry heating strongly influence the gelling properties of whey proteins

In this study we determined the composition (proportion of native proteins, soluble and insoluble aggregates) and quantified the gelling properties (gel strength and water holding capacity) of pre-texturized whey proteins by dry heating under controlled physicochemical conditions. For this purpose, a commercial whey protein isolate was dry heated at 80 °C (up to 6 days), 100 °C (up to 24 h) and 120 °C (up to 3 h) under controlled pH (2.5, 4.5 or 6.5) and water activity (0.23, 0.32, or 0.52). Gelling properties were quantified on heat-set gels prepared from reconstituted pre-texturized proteins at 10% and pH 7.0. The formation of dry-heat soluble aggregates enhanced the gelling properties of whey proteins. The maximal gelling properties was achieved earlier by increasing pH and water activity of powders subjected to dry heating. An optimized combination of the dry heating parameters will help to achieve better gelling properties for dry heated whey proteins.     

A comparison of selected quality characteristics of yoghurts prepared from thermosonicated and conventionally heated milks

Thermosonication (TS) of preheated (45 °C) milk (0.1%, 1.5% and 3.5% fat) for 10 min at an ultrasound frequency of 24 kHz allowed the preparation of yoghurts with rheological properties superior to those of control yoghurts produced from conventionally heated milk (90 °C for 10 min). Texture profile analysis and flow curves showed that yoghurts from the TS milks had stronger gel structures which displayed higher water-holding capacities (WHC) and lower syneresis. Based on averaged data from a sensory panel (n = 30), TS yoghurts showed superior texture and colour properties and samples with a fat content of 0.1% scored best in terms of overall acceptability. Retentions of water-soluble (thiamine and riboflavin) and fat-soluble (retinol and tocopherol) vitamins were similar in TS and conventionally prepared yoghurts.     

Effect of pH at heating on the acid-induced aggregation of casein micelles in reconstituted skim milk

Reconstituted skim milk samples at pH between 6.5 and 7.1 (heating pH) were heated at 80°C, 90°C or 100°C for 30 min (heating temperature). The particle size of the casein micelles was measured at pH 4.75-7.1 (measurement pH) and at temperatures of 10°C, 20°C and 30°C (measurement temperature) using photon correlation spectroscopy. The particle size of the casein micelles, at a measurement pH of 6.7 and a measurement temperature of 20°C, was dependent on the heating pH and heating temperature to which the milk was subjected. The casein micelle size in unheated milk was about 215 nm. At a heating pH of 6.5, the casein micelle size increased by about 15, 30 and 40 nm when the milk was heated at 80°C, 90°C or 100°C, respectively. As the heating pH of the milk was increased, the size of the casein micelles decreased so that, at pH 7.1, the casein micelles were ∼20 nm smaller than those from unheated milk. Larger effects were observed as the heating temperature was increased from 80°C to 100°C. The size differences as a consequence of the heating pH were maintained at all measurement temperatures and at all measurement pH down to the pH at which aggregation of the micelles was observed. For all samples, size measurements at 10°C showed no aggregation at all measurement pH. Aggregation occurred at progressively higher pH as the measurement temperature was increased. Aggregation also occurred at a progressively higher measurement pH as the heating pH was increased. The particle size changes on heating and the aggregation on subsequent acidification may be related to the pH dependence of the association of whey proteins with, and the dissociation of κ-casein from the casein micelles as milk is heated.     

Effect of thermal pretreatment of raw soymilk on the gel strength and microstructure of tofu induced by microbial transglutaminase

The influence of thermal pretreatment of raw soymilk on the gel hardness and microstructure of tofu, induced by microbial transglutaminase (MTGase), was investigated in this paper. Modulated differential scanning calorimetry analysis showed that individual proteins in soymilk were to a various extent denatured by different thermal pretreatments. The viscosity of the soymilk and the gel hardness of MTGase-induced tofu were more highly related with the heating rate (up to 90 °C) than the mode of heating. At any enzyme concentration of MTGase, the tofus prepared from soymilk heated at 75 °C for 10 or 30 min showed highest gel hardness among all tested ones (P?0.05). Scanning electron microscopy analysis indicated that the microstructure of the tofu from soymilk heated at 75 °C for 30 min had a unique coral-like structure, much more continuous and homogenous than that from soymilk at 95 °C for 5 min. These results confirmed that the appropriate heat pretreatment (e.g. in the present, at 75 °C for 10-30 min) remarkably improved the gel strength of tofu by means of MTGase, and strengthened the tofu gel structure.     

Aggregation and Dissociation of Milk Protein Complexes in Heated Reconstituted Concentrated Skim Milks

Heating milk at 120°C at pH 6.55 or pH 6.85 caused the denaturation of whey proteins and increased their association with the casein micelles. The dissociation of K -, β-, and α_s-caseins (in that order by extent) from the casein micelles increased with severity of heat treatment. The effect was greater at higher pH. Gel filtration chromatography followed by gel electrophoresis of fractions showed the dissociated protein was composed of disulfide-linked k -casein/β-lactoglobulin complexes of varying composition, casein aggregates of varying sizes and some monomeric protein. When reconstituted concentrate was prepared from NFDM made from heated milk the non-sedimentable (88,000 ± g for 90 min) caseins or whey proteins/heating time profiles were altered and the rate of aggregation, as measured by turbidity of heated milks, was significantly reduced.     

Standardization of milk using cold ultrafiltration retentates for the manufacture of Swiss cheese: effect of altering coagulation conditions on yield and cheese quality

Fortification of cheesemilk with membrane retentates is often practiced by cheesemakers to increase yield. However, the higher casein (CN) content can alter coagulation characteristics, which may affect cheese yield and quality. The objective of this study was to evaluate the effect of using ultrafiltration (UF) retentates that were processed at low temperatures on the properties of Swiss cheese. Because of the faster clotting observed with fortified milks, we also investigated the effects of altering the coagulation conditions by reducing the renneting temperature (from 32.2 to 28.3°C) and allowing a longer renneting time before cutting (i.e., giving an extra 5 min). Milks with elevated total solids (TS; ∼13.4%) were made by blending whole milk retentates (26.5% TS, 7.7% CN, 11.5% fat) obtained by cold (<7°C) UF with part skim milk (11.4% TS, 2.5% CN, 2.6% fat) to obtain milk with CN:fat ratio of approximately 0.87. Control cheeses were made from part-skim milk (11.5% TS, 2.5% CN, 2.8% fat). Three types of UF fortified cheeses were manufactured by altering the renneting temperature and renneting time: high renneting temperature = 32.2°C (UFHT), low renneting temperature = 28.3°C (UFLT), and a low renneting temperature (28.3°C) plus longer cutting time (+5 min compared to UFLT; UFLTL). Cutting times, as selected by a Wisconsin licensed cheesemaker, were approximately 21, 31, 35, and 32 min for UFHT, UFLT, UFLTL, and control milks, respectively. Storage moduli of gels at cutting were lower for the UFHT and UFLT samples compared with UFLTL or control. Yield stress values of gels from the UF-fortified milks were higher than those of control milks, and decreasing the renneting temperature reduced the yield stress values. Increasing the cutting time for the gels made from the UF-fortified milks resulted in an increase in yield stress values. Yield strain values were significantly lower in gels made from control or UFLTL milks compared with gels made from UFHT or UFLT milks. Cheese composition did not differ except for fat content, which was lower in the control compared with the UF-fortified cheeses. No residual lactose or galactose remained in the cheeses after 2 mo of ripening. Fat recoveries were similar in control, UFHT, and UFLTL but lower in UFLT cheeses. Significantly higher N recoveries were obtained in the UF-fortified cheeses compared with control cheese. Because of higher fat and CN contents, cheese yield was significantly higher in UF-fortified cheeses (∼11.0 to 11.2%) compared with control cheese (∼8.5%). A significant reduction was observed in volume of whey produced from cheese made from UF-fortified milk and in these wheys, the protein was a higher proportion of the solids. During ripening, the pH values and 12% trichloroacetic acid-soluble N levels were similar for all cheeses. No differences were observed in the sensory properties of the cheeses. The use of UF retentates improved cheese yield with no significant effect on ripening or sensory quality. The faster coagulation and gel firming can be decreased by altering the renneting conditions.     

Effect of pH at pressure treatment on the acid gelation of skim milk

Skim milk at pH between 6.4 and 7.3 was pressure treated at 200–600 MPa for 30 min and then slowly acidified with glucono-δ-lactone to form acid gels. Milks at low pH produced acid gels with low elastic moduli (final G′) and yield stresses and those at higher pH produced acid gels with higher final G′ and yield stresses. Pressure treatment disrupted the casein micelles at all pH and transferred high levels of casein to the serum phase. Denaturation of α-lactalbumin occurred at a pressure of 600 MPa only, and the level of denaturation increased with increasing pH. Denaturation of β-lactoglobulin (β-LG) occurred at all pressures, with the level of denaturation increasing with the magnitude of the pressure treatment and with pH. The denaturation of the whey proteins and the disruption of the casein micelles could not entirely account for the changes in the rheological properties of the acid gels, as denaturation of up to 50% of the whey proteins produced acid gels with very low final G′ and yield stresses. It is proposed that the pH and the magnitude of the pressure treatment affect the interactions of the denatured β-LG with the casein proteins in the pressure-treated milks, and that this affects the ability of the denatured β-LG to participate in the acid gel structures.Industrial relevanceThe control and manipulation of the firmness of acid skim milk gels is important in many dairy food applications such as yogurts and some types of cheeses. This study has demonstrated that acid gel firmness can be substantially manipulated when the milk is pH adjusted and pressure treated before acidification, and that these effects are different to those obtained through heating. The commercial uptake of high pressure processing in the dairy industry is dependent on this technology producing unique functional properties in milk when compared with traditional processing. The results of this study indicates that high pressure processing of milk may offer unique functional properties in acid gel applications which could be used for the development of new or improved dairy products.     

Effect of increasing the colloidal calcium phosphate of milk on the texture and microstructure of yogurt

The effect of increasing the colloidal calcium phosphate (CCP) content on the physical, rheological, and microstructural properties of yogurt was investigated. The CCP content of heated (85°C for 30 min) milk was increased by increasing the pH by the addition of alkali (NaOH). Alkalized milk was dialyzed against pasteurized skim milk at approximately 4°C for 72 h to attempt to restore the original pH and soluble Ca content. By adjustment of the milk to pH values 7.45, 8.84, 10.06, and 10.73, the CCP content was increased to approximately 107, 116, 123, and 128%, respectively, relative to the concentration in heated milk. During fermentation of milk, the storage modulus (G′) and loss tangent values of yogurts were measured using dynamic oscillatory rheology. Large deformation rheological properties were also measured. The microstructure of yogurt was observed using fluorescence microscopy, and whey separation was determined. Acid-base titration was used to evaluate changes in the CCP content in milk. Total Ca and casein-bound Ca increased with an increase in the pH value of alkalization. During acidification, elevated buffering occurred in milk between pH values 6.7 to 5.2 with an increase in the pH of alkalization. When acidified milk was titrated with alkali, elevated buffering occurred in milk between pH values 5.6 to 6.4 with an increase in the pH of alkalization. The high residual pH of milk after dialysis could be responsible for the decreased contents of soluble Ca in these milks. The pH of gelation was higher in all dialyzed samples compared with the heated control milk, and the gelation pH was higher with an increase in CCP content. The sample with highest CCP content (128%) exhibited gelation at very high pH (6.3), which could be due to alkali-induced CN micellar disruption. The G′ values at pH 4.6 were similar in gels with CCP levels up to 116%; at higher CCP levels, the G′ values at pH 4.6 greatly decreased. Loss tangent values at pH 5.1 were similar in all samples except in gels with a CCP level of 128%. For dialyzed milk, the whey separation levels were similar in gels made from milk with up to 107% CCP but increased at higher CCP levels. Microstructure of yogurt gels made from milk with 100 to 107% CCP was similar but very large clusters were observed in gels made from milk with higher CCP levels. By dialyzing heated milk against pasteurized milk, we may have retained some heat-induced Ca phosphate on micelles that normally dissolves on cooling because, during dialysis, pasteurized milk provided soluble Ca ions to the heated milk system. Yogurt texture was significantly affected by increasing the casein-bound Ca (and total Ca) content of milk as well as by the alkalization procedure involved in that approach.     

Milk clotting and proteolytic activity of an enzyme preparation from Bromelia hieronymi fruits

A new enzyme preparation (hieronymain), obtained from unripe fruits of Bromelia hieronymi Mez (Bromeliaceae), was assayed for its ability to clot milk and hydrolyze bovine casein and milk whey proteins. Caseinolytic activity at 30 °C and pH 6.5 (milk clotting conditions) was 3.3 Ucas/mL and milk clotting activity was 40 ± 0.2 IMCU/mL. The κ-casein fraction, involved in the clotting formation, began to be degraded after 10 min of reaction, while the degradation of the other casein fractions proceeded slowly enough as to guarantee the production of a firm curd, with no evidence of extensive hydrolysis, a necessary condition for cheese making. In the case of whey proteins, bovine serum albumin and α-lactalbumin were quickly degraded after 30 min, while β-lactoglobulin was considerably degraded only after 60 min at 50 °C. Miniature cheeses were manufactured both with chymosine and hieronymain and analyzed by a taste panel, who found acceptable both cheeses. Hieronymain might be appropriate for cheese making, as well as for the production of milk protein hydrolysates.