碎冰条件下单点系泊船舶动态响应特性研究

为了研究不同单点系泊位置对极地系泊船舶在来冰角度改变时动态响应的影响,运用离散元方法(DEM),计算了船舶在60%密集度下,冰速为1.0 m/s、冰厚为1 m时不同角度的船冰阻力,结合系泊分析软件二次开发功能,计算分析系泊船舶在不同来冰角度和不同系泊位置下受上述冰情影响下的响应。通过对模拟结果与试验结果的对比,认为离散元方法(DEM)的数值模拟结果与试验结果吻合较好;单点系泊位置为距船头L/4时,系泊船舶能以最快速、最稳定的方式对来冰方向的变化做出响应。     

浅水自调节外转塔单点系泊研究

针对渤海浅水边际油田的开采,提出了一种自调节外转塔单点系泊方式。此方案可根据水深调节锚链和配重分布,结合了单点系泊和多点系泊的优点,首部设置外转塔,海底用分布式锚链系泊,提高了系统运动的弹性空间。对该设计进行了理论分析、数值计算和模型试验。结果显示,数值计算和模型试验数据接近,系泊力和纵荡的最大误差分别为4.5%和7.05%,说明方案设计的计算依据合理。试验数据表明,系泊力和水平运动幅度较小,值得进一步研究或向工程推广。     

水深对软刚臂单点系泊FPSO动力响应的影响

系泊系统的定位能力是浅水油田作业的软刚臂式单点系泊FPSO安全作业的重要保障,为研究不同水深/吃水比下单点系泊系统的受力性能,针对一艘16万吨级软刚臂单点系泊FPSO,在线性三维势流理论的基础上,基于多体动力学方法,建立FPSO-系泊腿-软刚臂的耦合模型,采用Newman近似法和Pinkster近似法分析了FPSO所受二阶波浪力,在时域内计算了不同水深/吃水比对系泊系统动力响应性能的影响。结果表明,随着水深/吃水比的增加,Newman近似法计算得到二阶波浪力先增大后减小,引起单点系泊系统载荷先增大后减小;而Pinkster近似法计算得到的二阶波浪力逐渐减下,引起单点载荷逐渐减下。在浅水条件下,Pinkster近似法具有较好的适用性,Newman近似法严重低估了FPSO所受的二阶波浪力;在深水条件下,Newman近似法能满足工程计算的要求;适用两种方法的临界水深/吃水比为1.64。     

软刚臂单点系泊系统静力特性分析

软刚臂系泊系统是一种利用压载质量为浮式生产储油装置(FPSO)提供回复力的单点系泊方式。为快速准确地评估多铰接组成的软刚臂系统的受力状态,避免应用高复杂度的有限元软件,进而快速完成优化设计等任务,建立一种静力计算方法十分有必要。因此,针对由刚臂(YOKE)、柔性系泊腿和压载舱组成的刚柔多体系统,以分解组合的方式,提出一种二维静力计算方法,用以研究FPSO软刚臂系泊系统的静力特性。该方法主要依靠软刚臂的几何构型,在有限铰接约束下,形成非线性静力平衡方程,建立了压载舱式水上软刚臂单点系泊系统二维静力平衡计算算法。采用OrcaFlex、SESAM等软件开展了理论和数值对比分析,同时与系泊试验结果开展验证分析。对比结果表明,文中所提方法计算精度较高,可为软刚臂单点系泊系统的研究提供可靠支持。     

风浪流联合作用下单点系泊船的受力分析

研究了风浪流联合作用下单点系泊船的受力问题.在应用Newman公式计算波浪漂移力的基础上,结合文献《Fleet Moorings Design Manual》,提出了不同方向的风、浪、流联合作用时,单点系泊船所受到的横向力、纵向力和回转力矩的计算方法.提出了风浪同向时,不同风流夹角组合对应的船舶平衡位置的确定方法.为缆绳、锚的选择以及舵角的控制提供了依据.最后通过算例验证了本方法的适用性和实用性.     

单锚腿系泊系统动力响应的时域计算方法

在时域内建立了单锚腿系泊系统在风、浪、流联合作用下动力响应的计算方法。在分析波浪荷载时，使用了设计波法和非线性Stokes五阶波，并由经验公式求出了船舶的风、流荷载作用力。系统的动力初始条件由准静态方法求得。由静态方法得到系泊力后，使用了四阶Runge-Kutta方法求解船舶的运动时历，并作为立管和浮筒动力计算的边界条件。由二维梁柱单元和集中质量法构建了立管和浮简的数学模型，立管的运动方程用Wilson-θ法求解。模拟计算结果和试验结果进行了比较，吻合得较好,表明本方法能够用于计算单锚腿系泊系统的动力响应。     

风和流作用下单链式系泊养殖工船“鱼尾运动”研究

单点系泊船舶在受到风、流等外力作用下通常会产生大幅周期性艏摇运动，称为“鱼尾运动”。剧烈的鱼尾运动可能会导致系泊系统的锚链承受过大的张力从而遭到破坏。为了充分认识单点系泊状态下养殖工船的鱼尾运动，针对一艘十万吨级单链式系泊养殖工船进行了数值分析及模型试验研究。首先，通过风洞模型试验测得养殖工船的风、流载荷系数，以此作为输入对风、流联合作用下养殖工船的动力响应进行了数值模拟分析；同时，开展水池模型试验验证了数值计算结果的准确性和可靠性；最后，通过数值计算研究了不同风速和流速下单链式系泊养殖工船鱼尾运动的特性和规律，为实际工程设计提供一定的参考。     

FPSO系泊钢缆断丝松股成因分析及系泊方案改进

以南海某FPSO单点系泊系统为研究对象,针对其服役期间在极端海况下出现钢缆断丝、松股的问题展开研究。建立FPSO单点系泊系统模型,进行时域耦合动力分析,基于细长杆理论和有限元方法编写了单缆动力分析程序,通过与商业软件对比验证了程序的合理性,并发现极端海况下出现了系泊缆上部钢缆频繁触底和底部钢缆起落的现象,易引起钢缆的损伤。研究并提出了系泊缆配置新方案,通过调整分段长度避免了钢缆频繁触底、起落的问题;通过提高预张力,避免了系泊缆出现过度松弛的状态,该方案对于内转塔式单点系泊系统的设计与运维具有参考意义。     

规则波作用下四锚浮标系统动力分析

随着水深的增加,海洋浮标系泊缆索的长度也增加,对其浮标系泊系统进行动力分析是非常重要的.基于势流理论,应用边界元方法在频域内计算浮标的附加质量和阻尼、一阶波浪力和二阶平均漂移力,通过快速傅里叶变换将计算结果转换到时域,应用莫里森公式计算浮标及其skirt的粘性阻尼力,应用非线性有限元方法计算系泊缆索张力,最后在时域内应用四阶Runge- Kutta法计算浮标的运动响应和系泊缆索张力.比较分析了两种水深条件下,不同skirt直径和缆索长度情况下浮标的水动力特性、运动响应和系泊缆索张力.计算结果表明,浮标skirt的存在对纵荡方向的附加质量和辐射阻尼基本没有影响,而垂荡方向的附加质量增加,辐射阻尼减小,且能够减小二阶平均波浪力的峰值.     

刚臂式单点系泊系统在波浪作用下的链力分析

第一个刚臂式单点系泊储油装置(SBS)于1974年在突尼斯建成,以后在各地又建成了很多个这类装置,据报导其使用效果是令人满意的[1,2].为了发展我国海洋石油勘探、开发的科学技术,在海洋石油研究所的协助下,我们对这种系泊系统进行了波浪模型试验研究,本文在试验成果的基础上,主要研究单点浮筒多链系统的静力特性和波浪要素、水深等对链力的影响,还研究了减小中链力的措施.     

A Time Domain Computation Method for Dynamic Behavior of Mooring System

A quasi-steady time domain method is developed for the prediction of dynamic behavior of amooring system under the environmental disturbances,such as regular or irregular waves,winds and cur-rents.The mooring forces are obtained in a static sense at each instant.The dynamic feature of the moor-ing cables can be obtained by incorporating the extended 3-D lumped-mass method with the known shipmotion history.Some nonlinear effects,such as the influence of the instantaneous change of the wettedhull surface on the hydrostatic restoring forces and Froude-Krylov forces,are included.Thecomputational results show a satisfactory agreement with the experimental ones.     

浪流作用下系泊船舶撞击力和系缆力试验研究

以某25万吨矿石码头工程为例,分别进行了单流、单浪和浪流共同作用下,系泊船舶撞击力和系缆力试验。研究了不同水位、不同船舶载度、不同浪流夹角,单流、单浪和浪流共同作用时对船舶撞击力和系缆力的影响。分析了该码头工程护舷和缆绳的布置情况,为工程设计提供了依据。     

Experimental Study on Allowable Berthing and Mooring Conditions of An Oil Tanker

1 .ＩｎｔｒｏｄｕｃｔｉｏｎＷｈｅｎａｔａｎｋｅｒｉｓｂｅｒｔｈｅｄｏｒｍｏｏｒｅｄｔｏａｎｏｃｅａｎｐｌａｔｆｏｒｍ ,ｗｈｉｃｈｉｓｕｓｕａｌｌｙｉｎｏｐｅｎｓｅａｓ,ｔｈｅｔａｎｋｅｒｗｉｌｌｓｕｆｆｅｒｆｏｒｃｅｓｇｅｎｅｒａｔｅｄｂｙｗａｖｅｓ ,ｗｉｎｄａｎｄｃｕｒｒｅｎｔ.Ｉｎｍｏｓｔｏｆｔｈｅｐｒｅｖｉｏｕｓｓｔｕｄｉｅｓ ,ｔｈｅｉｎ ｆｌｕｅｎｃｅｏｆｃｕｒｒｅｎｔｏｒｔｈｅｃｏｍｂｉｎｅｄｗａｖｅａｎｄｃｕｒｒｅｎｔｗａｓｃｏｎｓｉｄｅｒｅｄｔｏｂｅｔｈｅｍａｉｎｏｂｊｅｃｔ.Ｉｎｓ…     

基于STAR-CCM+的浮标锚泊系统数值研究

浮标锚链因磨损而断裂会导致浮标丢失,所以针对浮标锚泊系统的研究对锚链设计具有重要意义。为解决锚链系泊力计算方法精度不足和锚链力学简化模型与锚链实际形态不一致的问题,通过VOF （Volume of Fluid） 界面捕捉法建立了三维风、浪耦合流场,基于流体力学计算软件STAR-CCM+对一种滚塑浮标及锚链进行数值仿真计算。在建立双链节锚链物理模型基础上,通过求解浮标在风、浪中的受力及浮标与锚链连接处的受力损失求取锚链系泊力。结果显示,风浪越大,锚链的系泊力损失越大,2、3、4 级海况下浮标阻力损失分别为17.1%、36.6%、55.8%。锚链的双链节受力并非均等,主受力链节在2、3 级海况时承担90%以上的锚链系泊力,次受力链节的系泊力随着总系泊力的增加而增加,可见双链节锚链规格应与单链节相同。     

Impact Analysis of Air Gap Motion with Respect to Parameters of Mooring System for Floating Platform

In this paper, the impact analysis of air gap concerning the parameters of mooring system for the semi-submersible platform is conducted. It is challenging to simulate the wave, current and wind loads of a platform based on a model test simultaneously. Furthermore, the dynamic equivalence between the truncated and full-depth mooring system is still a tuff work. However, the wind and current loads can be tested accurately in wind tunnel model. Furthermore, the wave can be simulated accurately in wave tank test. The full-scale mooring system and the all environment loads can be simulated accurately by using the numerical model based on the model tests simultaneously. In this paper, the air gap response of a floating platform is calculated based on the results of tunnel test and wave tank. Meanwhile, full-scale mooring system, the wind, wave and current load can be considered simultaneously. In addition, a numerical model of the platform is tuned and validated by ANSYS AQWA according to the model test results. With the support of the tuned numerical model, seventeen simulation cases about the presented platform are considered to study the wave, wind, and current loads simultaneously. Then, the impact analysis studies of air gap motion regarding the length, elasticity, and type of the mooring line are performed in the time domain under the beam wave, head wave, and oblique wave conditions.     

Investigation of Motion of Two Hinged Bodies Moored by Mooring Lines in Waves

In this paper, the motions are studied of a multi-body which is composed of two plates hinged together and moored by eight mooring lines in regular waves. The experimental results are compared with computational results. The linear po-tential theory and the perturbation method are combined to study this complicated system. The former is used to calculate the wave forces acting on the plates and the motion responses of them, while the latter is used to describe the dynamic character of the eight mooring lines coupled with the two hinged plates. Some response results of each plate are presented and comparisons between calculated results and experimental data are given. All the calculations are confined to regular beam waves.     

Design Curves for Mooring Lines of Turret Mooring Systems

This paper presents a series of design curves to aid in the selection of turret mooring systemsfor tankers based Floating Production Storage and Offloading(FPSO)systems.These curves are appropri-ate to water depths ranging from 100m to 600m.The curves can be used as a preliminary design tool,al-lowing the designer to quickly evaluate alternative mooring system configurations,including the numberof mooring lines,the characteristics of chain and wire rope to be deployed and the initial tension.With aknowledge of the total environmental force and vessel motion characteristics,the designer can determinethe appropriate system for closer evaluation.     

Study on Ship Automatic Berthing System with Mooring Lines

This study describes an automatic berthing system with mooring lines. It is designed to be berthed by using mooring device on the upper deck of a ship. It is to berth once maintaining parallel with the quay by controlling both forward and aft breast lines. Berthing method is used through length adjustment of mooring lines connected between ship and quay by controlling the angular velocity and the torque of hydraulic motor in mooring device. The study is conducted under three changing conditions of draft, such as even-keel, rise of the gravity center and trim to stern. Variables affecting berthing stability are determined based on the control performance of each condition. Bond graphs method is used to model the system. Controller is designed as PID control method of reference-model algorithm. The control program is composed of synchronous control system based on the equations derived with the numerical analysis. The tank test is conducted to verify the usefulness of the control program.