爆破地震动效应的数值模拟分析

爆破设计中,场地条件复杂时经验公式的应用受到一定限制。本文采用波动有限元分析方法,研究复杂场地条件下工程爆破时场地的地震动效应,研究爆破地震动特征及衰减规律。根据某重点工程场地岩土参数的原位测试和试验结果,用自行研制的软件包进行场地爆破地震动效应的数值模拟分析,为工程爆破设计及施工前建筑物、仪器设备的加固提供了依据。施工试爆实测结果与本文数值模拟分析给出的结果一致,说明本文方法是可行的,对其它工程也有借鉴作用。     

超限高层建筑结构抗震设计加强措施和建议——以某超限高层建筑为例

为加强超限高层建筑结构的抗震性能,最大程度减小地震损失,以某一超限高层建筑为对象,对其结构抗震设计的加强措施和建议进行详细分析。在小震作用下运用pkpm软件MIDAS/Building对建筑结构进行弹性计算对比分析,证明弹性计算的可靠性;借用SATWE对结构在中震或大震作用下不同构件的承载力和截面进行验算;采用midasbuilding软件对该超限高层建筑进行罕遇地震作用下的静力弹塑性分析。根据不同震级下建筑结构线弹性分析结果,对建筑主体结构、结构抗震和地基基础进行加强设计,从中归纳出整体结构的抗震加强措施和建议,说明该超限结构能满足规范的设防要求,是安全可靠的。     

Seismic vulnerability estimation of the building considering seismic environment and local site condition

Introduction The estimation of damage probability distribution among different damage states of rein-forced concrete buildings is a key component of earthquake loss estimation for modern city or a group of cities. With the development of city, the reinforced concrete buildings are major compo-nent parts of modern cities. Vulnerability estimates for these kinds of buildings are of importance to those responsible for civil protection, relief, and emergency services to enable adequate contin-genc…     

统一考虑地震环境和局部场地影响的建筑物易损性研究

提出了一种综合考虑地震环境和场地影响的钢筋混凝土房屋地震易损性分析方法. 将地震环境、局部场地和工程结构作为一个整体,以概率地震危险性分析的方式考虑地震环境的影响,在此基础上详细考虑了随局部场地而变化的反应谱形状对结构地震反应及其破坏概率分布的影响. 此外,还提出了另一种表述结构易损性的方式,以对应于不同超越概率地震危险水平的方式, 提供结构地震破坏概率分布的信息.      

Comparison of DSHA-based response spectrum with design response spectrum of building code of Pakistan (BCP-SP-2007) for a site in Muzaffargarh area,Pakistan

The building code of any country is considered to be a basic technical guidance document for the seismic design of structures. However, building codes are typically developed for the whole country, without considering site specific models that incorporate detailed site-specific data. Therefore, the adequacy of the design spectrum for building codes may sometimes be questionable. To study the sufficiency of the building codes of Pakistan (BCP-SP-2007), a deterministic seismic hazard analysis (DSHA) based spectrum was developed for a site in the Muzaffargarh area, Pakistan, using an updated earthquake catalogue, seismic source model, and a next generation attenuation model (NGA-WEST-2). Further, an International Building Code (IBC-2000) spectrum was developed for the study area to compare the results. The DSHA-based response spectrum resulted in a peak ground acceleration (PGA) value of 0.21 g for the Chaudwan fault. The evaluation of BCP-SP-2007 and IBC-2000 spectra provided a critical assessment for analyzing the associated margins. A comparison with the DSHA-based response spectrum showed that the BCP-SP-2007 design spectrum mostly overlapped with the DSHA spectrum unlike IBC-2000. However, special attention is needed for designing buildings in the study area when considering earthquake periods longer than 1 s, and the BCP-SP-2007 spectrum can be enhanced when considering a period range of 0.12–0.64 s. Finally, BCP-SP-2007 is based on a probabilistic approach and its comparison with deterministic results showed the significance of both methods in terms of design.     

Structure, soil–structure response and effects of damage based on observations of horizontal-to-vertical spectral ratios of microtremors

The microtremor horizontal-to-vertical-spectral-ratio (HVSR) technique is widely used in the urban environment to assess the fundamental frequency response of the ground. Extensive literature exists about case histories using HVSR for microzonation in several cities, but no systematic studies have been devoted to check the presence of soil–structure interaction effects, and even less attention to study building behaviour after earthquake damage. To evaluate the above-mentioned effects, a series of experiments are reported in this article.We first made a series of microtremor measurements on buildings and civil structures to evaluate the reliability of fundamental frequency determinations. Then, we considered several case studies to evaluate the effect of soil–structure interaction in estimates of site response in the presence of tall buildings. Finally, an experiment on the frequency change due to damage was performed. It was possible to confirm that HVSR is able to detect building fundamental modes and once known the building frequency, it is also possible to detect the presence of soil–structure interaction. Thus, once the presence of the building natural frequency is identified, it is possible to infer the site response from free field measurements. We also found that the HVSR technique is equally useful for detecting structural damage by determining the frequency shift of the buildings.     

基于时变地震损伤模型的多龄期钢框架结构易损性分析

基于时变地震损伤模型提出酸性大气环境作用下多龄期钢框架结构概率地震易损性分析的方法及步骤;考虑服役龄期对钢框架结构抗震性能的影响,分别建立时变概率地震需求模型、时变概率抗震能力模型及时变易损性模型;在概率地震需求分析及概率抗震能力分析的基础上,得到多龄期(20年、30年、40年、50年)钢框架结构的易损性模型及易损性曲线。     

DUAL-LEVEL SEISMIC DESIGN: A RELIABILITY-BASED METHODOLOGY

The seismic design provisions of most building codes in the United States specify ground motion parameters for various regions of the country and provide simple formulae to determine a distribution of lateral forces for which the structure should be designed. Although the code provisions are very simple to use, they oversimplify a complex problem and are based on many implicit assumptions which many designers may not appreciate. Furthermore, the reliability of the final design is not easily determined. This paper describes a reliability-based seismic design procedure for building structures. It is a performance-based design procedure which requires the designer to verify that a particular structural design satisfies displacement-based performance criteria. An equivalent system methodology and uniform hazard spectra are used to evaluate structural performance. The performance criteria are expressed in probabilistic terms, and deterministic design-checking equations are derived from these criteria. The design-checking equations incorporate design factors (analogous to load and resistance factors) which account for the uncertainty in the seismic hazard, the uncertainty in predicting site soil effects, and the approximate nature of the simplified models of the structure. The alternative procedure should enable designers to achieve code-specified target performance objectives for moderate and severe levels of earthquake excitation.     

Overview of the seismic input at dam sites in China

The current Chinese national standard, the Standard for Seismic Design of Hydraulic Structures (GB51247), released in 2018, is strictly based on China’s national conditions and dam engineering features. A comprehensive and systematic overview of the basis of the seismic fortification requirements, the framework of the fortification criteria, and the mechanisms of seismic input related to the seismic design of dams are presented herein. We first analyzed and clarified several conceptual aspects in traditional seismic design of dams. Then, for the seismic input at the dam site described in the first national standard for hydraulic structures, we expounded innovative concepts, ideas, and methods to make relevant provisions more realistic and practical and discussed whether reservoir earthquakes must be included in the seismic fortification framework of dams. This study seeks to incorporate seismic input at the dam site into traditional seismic design practice to promote its improvement from the quasi-static method to the dynamic method and from the closed vibration system to an open wave propagation system, to ensure that the seismic design of dams becomes more reasonable, reliable, scientific, and economic.     

Parametric analysis of the seismic response of a 2D sedimentary valley: implications for code implementations of complex site effects

A detailed 2D model has been constructed and validated for Euroseistest valley, in northern Greece. We take advantage of this model to investigate what parameters, in addition to surface soil conditions (obviously the most important parameter), can be used to correctly characterize site response in a 2D structure. Through a parametric analysis using 2D numerical simulations for SH waves, we explore the differences between the computed ground motion for different simplifications of the valley's structure. We consider variations in the velocity structure within the sediments, and variations of the shape between sediments and bedrock. We also compare the results from different 1D models reflecting current approaches to the determination of site response. Our results show clearly that, in the case of Euroseistest, site response owes fundamentally to its closed basin shape because it is largely controlled by locally generated surface waves. Thus, in terms of predicting site response, a rough idea of its shape ratio and of the average mechanical properties of the sediments are better than a very detailed 1D profile at the central site. Although the details of ground motion may vary significantly between the models, the relative amount of surface waves generated in the 2D models seems to be relatively constant. Moreover, if we quantify the additional amplification caused by the lateral heterogeneity in terms of the ‘aggravation factor’ introduced by Chávez-García & Faccioli [7], a roughly constant factor between 2 and 3 seems to appropriately take into account the effects of lateral heterogeneity. Of course, a correct estimate of the overall impedance contrast is necessary to correctly predict the maximum amplification, a caveat that also applies to 1D models. In this sense, Euroseistest rings an alarm bell. In this valley the more significant impedance contrast lies at about 200 m depth, and it is missed both by consideration of the average shear wave velocity of the first 30 m (the V_s30 criterion) or using the detailed velocity profile down to a depth where a shear wave velocity larger than 750 m/s is found. Our conclusions indicate that, in order to improve current schemes to take into account site effects in building codes, the more to be gained comes from consideration of lateral heterogeneity, at least in the case of shallow alluvial valleys, where locally generated surface waves are likely to be important.     

地震安全性评价和高层建筑的地震动输入

本文根据现行的中国地震烈度区划图中烈度的含义,指出在使用现行“建筑抗震设计规范”时存在的一些问题和与《中华人民共和国防震减灾法》的不协调之处。根据多年参加工程场地地震安全性评价的经验,总结了目前进行地震安全性评价过程中存在的一些问题。文中建议：针对高层建筑进行新的场地分类方法的研究;对高层建筑工程场地作地震安全性评价时,可根据高度的不同,适当简化安全性评价过程。     

Directional dependence of site effects observed near a basin edge at Aegion,Greece

We study site effects using 520 weak motion earthquake records from a vertical array in Aegion, Greece. The array is inside a basin, has four stations in soil, and one in bedrock (178 m depth). The site is marked by high seismicity and complex surface geology. We first use the records to establish the downhole accelerometer orientations and their evolution with time. Then we estimate site effects using empirical spectral ratios with and without a reference site (standard and horizontal-to-vertical spectral ratio). We find significant site amplification which cannot be accounted for by 1D model predictions, along with a significant difference in the amplification level between the two horizontal components. These are indications of 2D effects, namely surface waves generated at the basin edge. The difference in amplification between the horizontal components is maximised when these are rotated with respect to the orientation of the basin edge. The strongest amplification takes place in the direction parallel to the basin edge (SH, or out-of-plane motion), and is up to 2 times higher than in the perpendicular direction (SV, or in-plane motion). This directional effect on the amplification is corroborated by numerical 2D modelling using incident SH and SV waves, with the former possibly generating strong Love waves. In the records, the directionality is clear for windows containing the largest amplitudes of the records (S waves and strong surface waves), while it tends to vanish for coda-wave windows. This directionality is also observed when using response spectral ratios rather than Fourier ratios. We compute soil-to-rock amplification factors for peak ground acceleration (PGA) and find it is significantly higher than what is predicted by current design codes. We attribute this difference to the basin edge amplification, linear soil behaviour, and to the inability of simple scalar values like PGA to describe complex amplification effects. Finally, we analyse the earthquake records at a surface station near the slope crest and do not observe significant topographic amplification.     

Effect of soil depth on inelastic seismic response of structures

Effect of depth of soil stratum on estimated inelastic displacement of three typical structures, viz. a four storey building, a continuous bridge, and a tower, is studied and adequacy of the site amplification models of the current design codes and available empirical relationships is examined. The structures are assumed to be located on well-defined sites with varying bedrock depths, and effect of depth on elastic response spectrum, site amplification factor, displacement modification factor and inelastic displacement is studied, numerically, for two values of PGA. It is observed that soil depth has a significant effect on elastic as well as inelastic response of the structures; however, the effect of soil amplification on inelastic response is not as pronounced as in case of elastic response. Therefore, use of empirical site amplification models based on elastic response may be too conservative, for estimating inelastic response.     

消能减震技术用于C类框架学校建筑提高一度抗震设防加固的探讨

针对既有的C类框架学校建筑提高一度抗震设防的加固目标,从地震作用计算、结构抗震验算和抗震构造措施等方面详细分析了其中的加固难点,指出了应用传统抗震加固方法的一些不足之处,探讨了应用消能减震技术进行结构提高一度抗震设防加固的可行性;并以某C类框架学校建筑加固工程为实例,从减震控制效果分析、弹塑性变形验算、消能部件影响评价、抗震构造措施核查4个方面论证了消能减震加固方法的有效性和可操作性。结果表明,消能减震技术在C类框架学校建筑抗震加固中具有一定的应用优势,不但能有效控制结构的地震响应,而且依据减震效果可以适当降低结构的抗震构造要求。因此,只要通过合理的消能减震加固设计,再辅以额外的局部加强处理,完全可以实现C类框架学校建筑提高一度抗震设防的加固目标需求。     

南京河西地区设计地震动研究

本文根据南京及周围地区的地震环境,采用概率法对南京河西地区某高层公寓工程场址进行了地震危险性分析,采用等效线性化模型考虑场地土的非线性特性的影响,并用一维波动模型进行了场址土层地震反应和场地地震动效应分析,给出了５０年超越概率６３％,１０％和３％的场址基岩和地表的水平向加速度反应谱值加速度。     

Sensitivity of seismic structural response to interpretation of soils data

This paper investigates the sensitivity of the predicted seismic response of buildings in a PWR nuclear power station to the potential changes in the techniques and methods of interpreting soil data that have occurred over the last decade. The investigation is based on the soil-structure interaction (SSI) response of a typical PWR reactor building on a soft site during a seismic event. The current techniques and methods of interpretation of soils data tend to lead to a stiffer site with lower soil material damping than the earlier techniques. This leads to an increase in the SSI natural frequencies of typical buildings and an increase in its seismic response. This increase in the seismic response could put into question any seismic design based on seismic loads derived using the previously accepted generic soil data. The paper concludes with a recommendation for further consideration of the proposed departure from the previously accepted soil data.     

二维复杂工程场址设计地震动的修正分析方法

地震安全性评价中工程场地设计地震动通常采用一维等效线性化水平成层的分析模型，但对一些较复杂的场地条件，如蓄能电站所处场地，仅考虑一维场地是不够的，而需考虑二维场地的影响。常规采用的二维有限元很难考虑诸多因素，为工程设计带来了很大的困难。提出了可考虑二维复杂工程场地影响的设计地震动的修正分析方法和简化方法，该方法还可考虑非线性对场地的影响及吸能边界等因素，而且计算简单，并易于同常用的一维等效线性化方法结合。实例分析结果合理，对工程场地地震动的确定具有重要意义。     

建筑抗震设计中的小,中,大震烈度研究

作者以地震学的观点，在研究地震复发周期与震级－频度关系式中的ｂ值的基础上，研究了建筑抗震设计中的小、中、大震之间的烈度差值。指出该烈度差值只与ｂ值有关，因此是因地而异的。建议今后修改规范时考虑。     

美国建筑抗震设计的法规体系与设计地震动的确定

本文论述了美国建筑抗震设计法规体系发展演变过程及其代表性的规范、标准与技术文档;分析了美国当前建筑法规中设计地震动参数的重要技术见解,设计地震动的不同层次与作用,基于目标风险的最大考虑地震概念等技术的进展,同时,也总结了美国抗震设计相关法规中设计地震动确定的基本规定。本文旨在从美国庞大复杂的建筑设计法规体系中,梳理出清晰的建筑抗震设计的法规体系脉络与设计地震动的要求,为我国建筑抗震设计中设计地震动的相关研究提供参照。     

Constant-ductility strength demand spectra for seismic design of structures

In displacement-based seismic design, constant-ductility strength demand spectra （CDSDS） are very useful for preliminary design of new structures where the global displacement ductility capacity is known. The CDSDS can provide the required inelastic lateral strength of new structures from the required elastic lateral strength. Based on a statistical study of nonlinear time-history for an SDOF system, the mean CDSDS corresponding to four site conditions are presented and approximate expressions of the inelastic spectra are proposed, which are functions of the structural period and ductility level. The effects of site conditions, structural period, level of ductility, damping and post-yield stiffness of structures on CDSDS are also investigated. It is concluded that site conditions, ductility level and structural period have important effects on the CDSDS and damping, post-yield stiffness effects are rather complex and of minor importance. The damping, post-yield stiffness effects depend on both the level of ductility and the natural period of structures.