Isothermal crystallization kinetics and melting behavior of multiwalled carbon nanotubes/polyamide‐6 composites

Pristine and functionalized multiwalled carbon nanotubes (MWNTs) were used to fabricate polyamide 6 (PA6) composites through melt blending. The functionalized MWNTs were obtained by grafting 1,6‐hexamethylenediamine (HMD) onto the pristine MWNTs to improve their compatibility with PA6 matrix. The effect of MWNTs on the isothermal crystallization and melting behavior of PA6 was investigated by differential scanning calorimetry (DSC) and X‐ray diffraction (XRD). The Avrami and Lauritzen–Hoffmann equations are used to describe the isothermal crystallization kinetics. The values of the Avrami exponent found for neat PA6, the pristine MWNTs/PA6 and functionalized MWNTs/PA6 composite samples are about 4.0, 1.7, and 2.3, respectively. The activation energies are determined by the Arrhenius method, which is lower for the composites, ?320.52 KJ/mol for pristine MWNTs/PA6 and ?293.83 KJ/mol for functionalized MWNTs/PA6, than that for the neat PA6 (?284.71 KJ/mol). The following melting behavior reveals that all the isothermally crystallized samples exhibit triple melting endotherms at lower crystallization temperature and double melting endotherms at higher crystallization temperature. The multiple melting endotherms are mainly caused by the recrystallization of PA6 during heating. The resulting equilibrium melting temperature is lower for the composites than for neat PA6. In addition, polarizing microscopy (PLM) and small angle light scanning (SALS) were used to study the spherulite morphology. The results show that the MWNTs reduce the spherulite radius of PA6. This reduction is more significant for pristine MWNTs. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of nanoclay on the thermal,mechanical, and crystallization behavior of nanofiber webs of nylon‐6

Nylon‐6 and nanoclay/nylon‐6 composite nanofibers were prepared by electrospinning technique, in which formic acid was used as a solvent for good solubility of nylon‐6. The diameter of nylon‐6 and nanoclay/nylon‐6 nanofibers was below 350 nm and had smooth surfaces. The DSC heating curves of nylon‐6 and composites nanofibers show two endotherm behaviors, T_m1 (about 214°C) and T_m2 (about 220°C), corresponding to the melting events of γ‐form and α‐form crystals, respectively. The WAXs study showed that the γ‐crystalline phase predominantly present in both nylon‐6 and nanoclay/nylon‐6 nanofibers. The mechanical properties of the nanoclay/nylon‐6 composite nanofibers were higher than neat nylon‐6 electrospun nanofibers, which was decreased as the quantity of the clay increased. It might be due to the aggregation of nanoclay at high concentration. The thermal properties of the composite nanofibers were higher than neat nylon‐6 nanofibers. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes in poly(p‐phenylene sulfide) composites

To investigate the nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes (MWNTs‐OH) in poly(p‐phenylenesulfide) (PPS), a series of composites were prepared by blending PPS with MWNTs‐OH at 1, 2, and 3 wt %, respectively. Under SEM observation MWNTs‐OH were found homogeneously dispersed in the PPS matrix. DSC thermograms revealed that the enthalpy (ΔH_c) of the composites increased with increasing MWNT‐OH content, whereas the crystallization temperature (T_c) decreased progressively. The decrease in T_c was in accordance with the smaller crystallite size determined with WXRD characterization, and the increase in ΔH_c was evidenced by FTIR and XPS analyses. The higher ΔH_c shows that MWNTs‐OH serves as a nucleating agent, providing sufficiently multiplied sites for crystal growth. The lowering of T_c was attributed not only to MWNTs‐OH network hindrance to PPS chain fusing rearrangement, but also to a poorer affinity between MWNTs‐OH and PPS; both effects coordinately govern T_c of PPS/MWNTs‐OH composites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and properties of homogeneously dispersed polyamide 6/MWNTs nanocomposites via simultaneous in situ anionic ring‐opening polymerization and compatibilization

Toluene 2, 4‐diisocyanate (TDI) functionalized multiwalled carbon nanotubes (MWNTs‐NCO) were used to prepare monomer casting polyamide 6 (MCPA6)/MWNTs nanocomposites via in situ anionic ring‐opening polymerization (AROP). Isocyanate groups of MWNTs‐NCO could serve as AROP activators of ?‐caprolactam (CL) in the in situ polymerization. Fourier transform infrared (FTIR) showed that a graft copolymer of PA6 and MWNTs was formed in the in situ polymerization. MWNTs‐PA6 covalent bonds of the graft copolymer constituted a strong type of interfacial interaction in the nanocomposites and increased the compatibility of MWNTs and MCPA6 matrix. The nanocomposites were characterized for the morphology, mechanical, crystallization, and thermal properties through field emission transmission electron microscopy (FETEM), tensile testing, differential scanning calorimeter (DSC), and thermogravimetric analysis (TGA). FETEM analysis showed that MWNTs were homogeneously dispersed in MCPA6 matrix. The initial tensile strengths and tensile modulus of the nanocomposite with 1.5 wt % loading of MWNTs were enhanced by about 16 and 13%, respectively, compared with the corresponding values for neat MCPA6. DSC analysis indicated that the crystallization temperature of the nanocomposites was increased by 8°C by adding 1.5 wt % MWNTs compared with pure MCPA6. Besides, it was found that the thermal stability of MCPA6 was improved by the addition of the MWNTs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology,thermal, and rheological behavior of nylon 11/multi‐walled carbon nanotube nanocomposites prepared by melt compounding

Nylon 11 (PA11) nanocomposites with different loadings of multi‐walled carbon nanotubes (MWNTs) were prepared by melt compounding. Scanning electron microscopy images on the fracture surfaces of the composites showed a uniform dispersion of MWNTs throughout the matrix. The presence of the MWNTs significantly improved the thermal stability and enhanced the storage modulus (G′) of the polymer matrix. Melt rheology studies showed that, compared with neat PA11, the incorporation of MWNT into the matrix resulted in higher complex viscosities (|η*|), storage modulus (G′), loss modulus (G″), and lower loss factor (tanδ). PA11 and its nanocomposites containing less than 1 wt% MWNTs showed similar frequency dependencies and reached a Newtonian plateau at low frequencies. For the nanocomposite with 2 wt% MWNTs, the regional network was destroyed and the orientation of the MWNTs during shearing exhibited a very strong shear thinning effect. The complex viscosities (|η*|) of the nanocomposites are larger than that of neat PA11 and decreased with increasing the temperature. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

The morphology and thermal properties of multi‐walled carbon nanotube and poly(hydroxybutyrate‐co‐hydroxyvalerate) composite

Nanocomposites based on poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) and multi‐walled carbon nanotubes (MWNTs) were prepared by solution processing. Ultrasonic energy was used to uniformly disperse MWNTs in solutions and to incorporate them into composites. Microscopic observation reveals that polymer‐coated MWNTs dispersed homogenously in the PHBV matrix. The thermal properties and the crystallization behavior of the composites were characterized by thermogravimetric analysis, differential scanning calorimetry and wide‐angle X‐ray diffraction, the nucleant effect of MWNTs on the crystallization of PHBV was confirmed, and carbon nanotubes were found to enhanced the thermal stability of PHBV in nitrogen. Copyright © 2004 Society of Chemical Industry     

Effect of multi‐walled carbon nanotubes on crystallization,thermal, and mechanical properties of poly(vinylidene fluoride)

Composites were prepared by solution blending poly(vinylidene fluoride) (PVDF) and multi‐walled carbon nanotubes (MWNTs). Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) results showed that the crystalline structure of PVDF was changed by the addition of MWNTs and a MWNTs‐induced crystal transformation from α‐phase to β‐phase of PVDF was confirmed. With differential scanning calorimeter (DSC) and dynamic mechanic thermal analysis (DMA) techniques, thermal and mechanical properties of the composite films were examined. As the DSC results showed, addition of MWNTs would lead to the increased cooling crystallization temperature (T_c), implying that MWNTs nanoparticles could act as nucleating agents, which is further proved with the help of polarized optical microphotographs. On the other hand, the decreasing of D_d (degree of crystallinity) implied that the MWNTs networks can confine the crystallization of PVDF. Through the curve analysis of the dynamic mechanical measurements, it was found that the storage modulus (E′) is significantly enhanced, revealing that a strong interaction should exist between PVDF and MWNTs. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Properties of anionic polymerized ε‐caprolactam in the presence of carbon nanotubes

The results of the investigations of the relations between structure, physical and usage properties of polyamide 6 (PA6) reinforced with multiwall carbon nanotubes (MWNTs) are presented. A method of in situ anionic bulk polymerization of ε‐caprolactam in the presence of MWNTs was used for the preparation of reinforced PA6. The polymerization product was crushed, and the pellets of PA6 and PA6/MWNTs composites were injection molded to produce the standard test specimens for various measurements. The surface morphology (SEM), thermal (DSC, TGA, DMTA), and mechanical properties (tensile strength, Charpy's notched impact strength) of these materials were examined. Some differences between our specimens and those obtained by hydrolytic polymerization of ε‐caprolactam (CL) were found. It was found that a small amount of carbon nanotube decreases the crystallinity degree of PA6 matrix in the composites. The thermal stability was higher than that for neat PA6. DMTA results showed that the magnitudes of the storage modulus are higher for the PA6/MWNTs composites than for the unmodified PA6 in the temperature range between ?90 and 200°C. The tensile strength and tensile modulus are higher compared with the neat PA6. The elongation at break showed no noticeable change in the range of MWNTs loading considered, while the Charpy's notched impact strength slightly decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Evolution of phase morphology and ‘network‐like’ structure of multiwall carbon nanotubes in binary polymer blends during melt‐mixing

Polyamide6 (PA6)/acrylonitrile butadiene styrene copolymer (ABS) blends with unmodified multiwall carbon nanotubes (MWNTs) were prepared via melt‐blending in a conical twin‐screw micro‐compounder with varying melt‐mixing time. To improve the state of dispersion of MWNTs, non‐covalent organic modifiers for MWNTs have been utilized: sodium salt of 6‐amino hexanoic acid (Na‐AHA) and 1‐pyrene‐carboxaldehyde (PyCHO). PA6/ABS blends with MWNTs have shown a phase morphology transition from ‘matrix‐dispersed droplet’ type to ‘co‐continuous’ type as a function of melt‐mixing time with the exception of 40/60 PA6/ABS blend with PyCHO‐modified MWNTs. Non‐isothermal crystallization studies revealed the heterogeneous nucleating action of MWNTs through the presence of double crystallization exothermic peaks (at ～192^°C and >200^°C) while pure PA6 shows bulk crystallization peak at ～192°C. 40/60 and 60/40 (wt/wt) PA6/ABS blends with 5 wt% unmodified MWNTs exhibited electrical conductivity values of ～3.9 × 10^?11 S/cm and ～4.36 × 10^?6 S/cm, respectively. A significant enhancement in electrical conductivity was observed with Na‐AHA and PyCHO‐modified MWNTs (order of ～10^?6 and ～10^?4 S/cm, respectively). POLYM. ENG. SCI., 55:429–442, 2015. © 2014 Society of Plastics Engineers     

Fabrication and Characterization of Soluble Multi‐Walled Carbon Nanotubes Reinforced P(MMA‐co‐EMA) Composites

Summary: Soluble multi‐walled carbon nanotubes (s‐MWNTs), obtained via amidation reaction of octadecylamine with purified multi‐walled carbon nanotubes (p‐MWNTs), were solution‐mixed with P(MMA‐co‐EMA) at various loadings. Compared to the p‐MWNTs/P(MMA‐co‐EMA) composites, the s‐MWNTs/P(MMA‐co‐EMA) composites showed great improvement both in Young's modulus and tensile strength. With the addition of 10 wt.‐% s‐MWNTs, the Young's modulus and tensile strength of s‐MWNTs/P(MMA‐co‐EMA) composite have 135% and 49% increase over the pure P(MMA‐co‐EMA), respectively, and a 9.2% increase in Young's modulus and 12.8% increase in tensile strength over that of 10 wt.‐% p‐MWNTs composite. With the increase of MWNTs content, the T_g increases from 89 to 106 °C. SEM studies show that the s‐MWNTs are well dispersed in the polymer matrix. Good dispersion of s‐MWNTs in polymer matrix and great interfacial bonding between s‐MWNTs and P(MMA‐co‐EMA) may be the key reason for the improvement of the mechanical properties.

Stress‐strain curves of the MWNTs and P(MMA‐co‐EMA) composites.     

Crystallization behavior of polyamide 11/multiwalled carbon nanotube composites

Differential scanning calorimetry (DSC) was used to investigate the isothermal and nonisothermal crystallization kinetics of polyamide11 (PA11)/multiwalled carbon nanotube (MWNTs) composites. The Avrami equation was used for describing the isothermal crystallization behavior of neat PA11 and its nanocomposites. For nonisothermal studies, the Avrami model, the Ozawa model, and the method combining the Avrami and Ozawa theories were employed. It was found that the Avrami exponent n decreased with the addition of MWNTs during the isothermal crystallization, indicating that the MWNTs accelerated the crystallization process as nucleating agent. The kinetic analysis of nonisothermal crystallization process showed that the presence of carbon nanotubes hindered the mobility of polymer chain segments and dominated the nonisothermal crystallization process. The MWNTs played two competing roles on the crystallization of PA11 nanocomposites: on the one hand, the MWNTs serve as heterogeneous nucleating agent promoting the crystallization process of PA11; on the other hand, the MWNTs hinder the mobility of the polymer chains thus retarding the crystal growth process of PA11. The activation energies of PA11/MWNTs composites for the isothermal and nonisothermal crystallization are lower than neat PA11. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Microstructure,crystallization and dynamic mechanical properties of polyamide/clay nanocomposites after melt‐state annealing

Polyamide 6/clay (PA/clay) nanocomposites produced by melt‐compounding were treated under various melt‐state annealing processes. The effect of melt‐state annealing on the microstructure, crystallization, and dynamic mechanical properties was characterized by transmission electron microscope (TEM), modulated differential scanning calorimetry (MDSC), X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and dynamic mechanical analysis (DMA). Clay layers were exfoliated in PA matrix. The crystalline transformation between α and γ‐crystalline phase was virtually dependent on the annealing process and clay loading. After melt‐state annealing between 230 and 250°C, clay induced the appearance of a new endothermic peak in PA/clay. PA/clay after melt‐state annealing exhibited a higher elastic modulus above T_g and a lower β relaxation below T_g as compared with the non‐annealed sample. FTIR analysis demonstrated that the melt‐state annealing caused strong hydrogen bonding interaction of amide groups with clay layers. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Crystallization behavior of polypropylene/polyamide 6/montmorillonite nanocomposites

Polymer blended materials such as polyamide 6 (PA6)/polypropylene (PP) blends have received considerable attention in recent years. To improve the compatibility of PA6 and PP, compatibilizers like maleic anhydride‐g‐polypropylene (MPP) are often added. In addition, organically modified montmorillonite (MMT) is also used to improve the properties of various materials. In this work, the crystallization behavior of PP/PA6/MMT nanocomposites with MPP compatibilizer was investigated systematically. The annealing process effectively improved the crystallization of α‐PP. The crystallization temperature (T_c) of PA6 was increased by ca 2–3 °C on introducing MPP or MMT alone to the PP/PA6 system, whereas T_c of PP underwent no obvious change. However, when MPP and MMT were added simultaneously, T_c of PP and PA6 increased by 6.6 and 4.2 °C, respectively, and a new crystallization peak corresponding to PP‐g‐PA6 copolymer phase was observed at 162.5 °C. The combined effect of MPP and MMT led to better compatibility of PP with PA6. Moreover, the results of a non‐isothermal crystallization kinetics experiment revealed that the simultaneous introduction of MPP and MMT markedly shortened the crystallization time. Copyright © 2010 Society of Chemical Industry     

The effect of pressure and clay on the crystallization behavior and kinetics of polyamide‐6 in nanocomposites

The crystallization kinetics of polyamide‐6 (PA‐6) and its nanocomposite (PNC) with 2% clay were studied, using a pressure dilatometer (50 MPa to 200 MPa) to follow the volume changes associated with the crystallization process. Isobaric experiments were carried out to evaluate the effect of pressure and clay on melting temperature (T_m) and crystallization temperature (T_a) of PA‐6. The melting temperatures of PA‐6 in the PNC were very close to those of PA‐6 alone at comparable pressures, but the crystallization temperatures in the PNC were lower than those of PA‐6 alone. The materials exhibited two crystallization zones in isothermal/isobaric experiments. The initial zone involved both the γ‐form and the α‐form of PA‐6, while in the latter zone the γ‐form was dominant. The Avrami equation was used to fit the isothermal/isobaric crystallization data. The Avrami exponent n was between 1.0 and 3.2 for the γ‐form of unfilled PA‐6, between 0.9 and 2.6 for the γ‐form in PNC and for the γ‐form of PA‐6 alone, n was between 1.0 and 2.1 and in PNC between 1.2 and 2.6. The Avrami rate constants (K) for PA‐6 and PNC depend on the experimental crystallization temperature as well as pressure. The rate of crystallization under similar conditions was higher for PNC. Infrared studies on compression molded PA‐6 and PNC samples, cooled from melt at different rates, confirm the formation of the γ‐form in the initial stages of crystallization, as well as its transformation into the α‐form at later stages. In the case of PNC, the γ‐form stabilized when the sample was quenched from melt.     

Enhanced dielectric properties of polyamide 11/multi‐walled carbon nanotubes composites

Composites with multi‐walled carbon nanotubes (MWNTs) involved in polyamide 11 (PA11) were prepared via a conventional melt blending method. The structure, morphology, crystallization behavior, electrical, and dielectric properties of composites were investigated. The results demonstrated that the dispersed uniformly MWNTs favored the formation of α crystal of PA11 when the composites were quenched from melt. The dielectric constant of composites was dependent on the electric field frequency and MWNTs content, and the highest value of dielectric constant was as high as 350 for the composite with 1.21 vol % MWNTs at 10³ Hz, accompanied by a low dielectric loss. The enhanced dielectric properties could be interpreted by the formation of abundant nanocapacitors within the composites and the interfacial polarization effect resulting from accumulation of charge carriers at the internal interfaces between MWNTs and PA11. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42642.     

Filler reaggregation and network formation time scale in extruded high‐density polyethylene/multiwalled carbon nanotube composites

A high‐density polyethylene (HDPE) masterbatch containing 20.2 wt% multiwalled carbon nanotubes (MWNTs) was melt diluted with neat HDPE using two different methods: a twin screw microcompounder and a single‐screw extruder. The electrical properties of these composites were assessed using bulk electrical conductivity measurements, their mechanical properties were evaluated using tensile tests and dynamic mechanical analysis (DMA), and percent crystallinity was determined by wide angle x‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). A percolation threshold (p_c) of 4.5 wt% MWNTs was found in compression‐molded samples. Extruded samples were prepared with nanotube concentrations below and above the compression‐molded percolation threshold (2 and 7 wt% MWNTs) and passed through the extruder twice before entering a low‐shear melt annealing zone. Different melt annealing times were used and their effects on the electrical and mechanical properties of the resulting quench‐cooled composites were evaluated. Results showed that extruded composites were nonconductive, indicating that a conductive nanotube network did not form on the time scale of these experiments. Annealing time also did not affect significantly the mechanical properties of the resulting solid composites. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Nonisothermal crystallization behavior of melt‐intercalated polyethylene‐clay nanocomposites

The influence of nanoclay particles on the nonisothermal crystallization behavior of intercalated polyethylene (PE) prepared by melt‐compounding was investigated. It is observed that the crystallization peak temperature (T_p) of PE/clay nanocomposites is slightly but consistently higher than the neat PE at various cooling rates. The half‐time (t_0.5) for crystallization decreased with increase in clay content, implying the nucleating role of nanoclay particles. The nonisothermal crystallization data are analyzed using the approach of Avrami (Polymer 1971, 12, 150), Ozawa (Polym Eng Sci 1997, 37, 443), and Mo and coworkers (J Res Natl Bur Stand 1956, 57, 217), and the validity of the different kinetic models to the nonisothermal crystallization process of PE/clay nanocomposites is discussed. The approach developed by Mo and coworkers successfully explains the nonisothermal crystallization behavior of PE and PE/clay nanocomposites. The activation energy for nonisothermal crystallization of neat PE and PE/clay nanocomposites is determined using the Kissinger (J Res Natl Bur Stand 1956, 57, 217) method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3809–3818, 2006     

Polyamide 6–Cellulose Composites: Effect of Cellulose Composition on Melt Rheology and Crystallization Behavior

Melt rheology and crystallization behavior of polyamide 6 (PA 6) and microcrystalline cellulose (MCC) composites were systematically studied in this research. The incorporation of MCC into the PA 6 matrix resulted in higher complex viscosities (|η*|), storage modulus (G′), and shear viscosities than those of neat PA 6, especially at low frequencies. The orientation of rigid molecular chains in the composites introduced by the addition of MCC induced a strong shear thinning behavior with an increase in MCC loading. The non‐isothermal crystallization kinetics of PA 6 and MCC composites were investigated by differential scanning calorimetry. The Avrami and Tobin model were applied to describe the process of non‐isothermal crystallization and to determine the crystallization parameters of the composites. Analysis of the crystallization kinetics indicated that the Avrami (n_a) and Tobin exponent (n_t) was altered by the MCC. It was also found that the Avrami and Tobin equations fit the empirical data well. POLYM. ENG. SCI., 54:739–746, 2014. © 2013 Society of Plastics Engineers     

Effect of low‐temperature annealing on dimensional stability of poly(ethylene 2,6‐naphthalene dicarboxylate) fibers melt‐spun at high speed

To investigate structural factors, necessary to obtain a valuable industrial fiber possessing excellent thermomechanical properties, poly(ethylene 2,6‐naphthalene dicarboxylate) (PEN) fibers were produced by high‐speed melt‐spinning to a take‐up speed of 8 km/min, followed by low‐temperature annealing between the glass‐transition temperature (T_g) and exothermic cold crystallization temperature (T_{c cold}), where little transition of crystalline phase, as well as little thermal degradation, takes place. Their thermomechanical behavior, as well as structural variations, were investigated through differential scanning calorimetry, Rheovibron, thermomechanical analysis (TMA), and tensile testing. Two types of the α‐ and α′‐dispersions were observed at near T_g and at a temperature 50–60°C higher than T_g, respectively. The dispersions were affected by rearranged structures, which are generated by developing an inhomogeneous taut structure with rigidity of aromatic segment and aliphatic segment. The α‐dispersion seemed to reflect an inhomogeneous taut structure by the less nearly arranged segments. Consequently, at intermediate take‐up speeds between 2 and 6 km/min the inhomogeneous taut structure may be partially formed, but the homogeneously ordered structure may be enlarged as the take‐up speed and annealing temperature increased. Thermal shrinkage increased above the α‐dispersion temperature, which suggested that the onset point of dimensional change in PEN fibers was attributed to α‐dispersion. In the case of annealed fibers, the start of length change coincided with the respective annealing temperatures, which indicated that dimensional stability could be gained from restraining the inhomogeneous taut structure in the amorphous region without the transition of crystalline phase by annealing between T_g and T_{c cold}. Therefore, to obtain dimensional stability in PEN fibers, it is supposed that the inhomogeneous taut structure exhibited by the α‐dispersion should be controlled. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 212–218, 2005     

Isothermal crystallization and melting behaviors of nano TiO2‐modified polypropylene/polyamide 6 blends

Titanium dioxide (TiO₂) nanoparticles were functionalized with toluene‐2,4‐diisocyanate and then polypropylene/polyamide 6/(PP/PA6) blends containing functionalized‐TiO₂ were prepared using a twin screw extruder. Isothermal crystallization and melting behavior of the as‐prepared composites were investigated using differential scanning calorimetry and wide‐angle X‐ray diffraction. Isothermal crystallization analysis shows that the TiO₂ nanoparticles have two effects on PP/PA6 blends, i.e., it can favor the improvement of crystallization ability and decrease the crystallization rate of PP/PA6 blends. The improvement of crystallization ability is superior over decreasement of crystallization rate of PA6 chains caused by TiO₂, therefore PA6 in PP/PA6/TiO₂ nanocomposites have higher crystallization rate than that of PA6 in pure PP/PA6 blends, which indicated TiO₂ nanoparticles favored the crystallization of PA6. The TiO₂ nanoparticles show no effects on the equilibrium melting temperature (T) values of PP phase but decreases the T values of PA6 phase. In addition, the TiO₂ nanoparticles did not change the crystalline polymorph of PP/PA6 blends basically; however, favored the formation of β‐PP. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers