Preparation and characterization of poly(3-octylthiophene)/carbon fiber thermoelectric composite materials

Poly(3-alkylthiophene) (P3AT) with a high Seebeck coefficient has recently been reported. However, P3AT/inorganic conductive composites exhibit relatively poor thermoelectric performance because of their low electrical conductivity. In this work, carbon fiber sheets with a high electrical conductivity were chosen as the inorganic phase, and poly(3-octylthiophene)(P3OT)/carbon fiber composites were prepared by casting P3OT solution onto the carbon fiber sheets. The carbon fiber sheets incorporated into the composites can provide good electrical conductivity, and P3OT can provide a high Seebeck coefficient. The highest power factor of 7.05 μW m⁻¹ K⁻² was obtained for the composite with 50 wt% P3OT. This work suggests a promising method for preparing large-scale thermoelectric composites with excellent properties.     

Preparation,characterization and properties of polycaprolactone diol-functionalized multi-walled carbon nanotube/thermoplastic polyurethane composite

Multi-walled carbon nanotubes (MWCNTs) were chemically functionalized to prepare thermoplastic polyurethane (PU) composites with enhanced properties. In order to achieve a high compatibility of functionalized MWCNTs with the PU matrix, polycaprolactone diol (PCL), as one of PU’s monomers, was selectively grafted on the surface of MWCNTs (MWCNT–PCL), while carboxylic acid groups functionalized MWCNTs (MWCNT–COOH) and raw MWCNTs served as control. Both MWCNT–COOH and MWCNT–PCL improved the dispersion of MWCNTs in the PU matrix and interfacial bonding between them at 1 wt% loading fraction. The MWCNT–PCL/PU composite showed the greatest extent of improvement, where the tensile strength and modulus were 51.2% and 33.5% higher than those of pure PU respectively, without sacrificing the elongation at break. The considerable improvement in both mechanical properties and thermal stability of MWCNT–PCL/PU composite should result from the homogeneous dispersion of MWCNT–PCL in the PU matrix and strong interfacial bonding between them.     

Preparation and thermal properties of soluble poly(phthalazinone ether sulfone ketone) composites reinforced with multi-walled carbon nanotube buckypaper

A nanocomposite with soluble high-performance poly(phthalazinone ether sulfone ketone) (PPESK) as matrix and multi-walled carbon nanotube buckypaper (MWCNT-BP) as reinforcement was fabricated by hot-press processing. The morphologies, dynamic and static mechanical behavior, thermal stability of the MWCNT-BP/PPESK composites were studied using scanning electron microscope (SEM), dynamic mechanical analyzer (DMA) and thermogravimetric analyzer (TGA). SEM microphotographs revealed a high impregnation degree of the MWCNT-BP/PPESK composites. Dynamic and static mechanical analysis revealed that the nanocomposites possessed high storage modulus, and good retention rate of mechanical strength even at 250 °C, which is mainly attributed to satisfied impregnation and strong interactions between MWCNT-BP and PPESK. Thermogravimetric analysis exhibited that the nanocomposites had excellent thermal stability. These investigations confirm that MWCNT-BP can be effectively used to manufacture high-loading CNT/PPESK composites with improved properties.     

Relation between repeated uniaxial compressive pressure and electrical resistance of carbon nanotube filled silicone rubber composite

Carbon nanotube filled polymer composite can be used as sensitive material of flexible pressure sensor. By using solution mixing method, carbon nanotubes are dispersed into silicone rubber matrix to fabricate the composite. The piezoresistivities of the composite with different carbon nanotube concentrations under repeated compressions are researched quantitatively. The monotonicity of the piezoresistivity is dependent on the content of carbon nanotube and the range of the applied pressure. The reproducibility error of the piezoresistivity decreases with the increase of the compression cycles. The experimental data of the piezoresistivity are fitted by the linear combination of two exponential functions. The piezoresistive mechanism is studied qualitatively by analyzing the changes in the carbon nanotube network.     

Effects of poly(oxyethylene)-block structure in polyetheramines on the modified carbon nanotube/poly(lactic acid) composites

The hybrids of multi-walled carbon nanotube and poly(lactic acid) (MWCNT/PLA) were prepared by a melt-blending method. In order to enhance the compatibility between the PLA and MWCNTs, the surface of the MWCNTs was covalently modified by Jeffamine® polyetheramines by functionalizing MWCNTs with carboxylic groups. Different molecular weights and hydrophilicity of the polyethermaines were grafted onto MWCNTs with the assistance of a dehydrating agent. The results showed that low-molecular-weight Jeffamine® polyetheramine modified MWCNTs can effectively improve the thermal properties of PLA composites. On the other hand, high-molecular-weight and poly(oxyethylene)-segmented polyetheramine could render the modified MWCNTs of well dispersion in PLA, and consequently affecting the improvements of mechanical properties and conductivity of composite materials. With the addition of 3.0 wt% MWCNTs, the increment of E′ of the composite at 40 °C was 79%. For conductivity, the surface resistivity decreased from 1.27 × 10¹² Ω/sq for neat PLA to 8.30 × 10⁻³ Ω/sq for the composites.     

Tuning of liquid sensing performance of conductive carbon black (CB)/polypropylene (PP) composite utilizing a segregated structure

Carbon black (CB)/polypropylene (PP) with a novel segregated structure was fabricated. For this composite, CB particles were selectively distributed on the interfaces between PP polyhedrons, leading to a lower percolation threshold (2.34 vol%). Liquid sensing behaviors of the composite were studied. Nice selectivity, high response rate and high response intensity have been achieved. The designed interfaces, which accelerate the penetration of solvents under the action of the capillary effect, are responsible for the nice performances. A fine reproducibility has also been obtained. This study offers an approach for manufacturing high performance liquid sensor by tailoring the microstructure of a composite.     

Chinese ink-facilitated fabrication of carbon nanotube/polyvinyl alcohol composite sheets with a high nanotube loading

Fabricating carbon nanotube-based composites requires high degree of dispersion of carbon nanotubes into a polymer matrix. The widely used approaches reported in open literature for such a purpose are usually complicated and high-cost. Herein, we found that Chinese ink could be used to prepare composites composed of multi-walled carbon nanotubes (MWCNTs) and polyvinyl alcohol (PVA). The Chinese ink acted as a solvent and a dispersant. The MWCNT-ink-PVA ternary composite possessed both high flexibility and high electrical conductivity, with an optimized electrical conductivity of 8.17 S cm⁻¹. This simple method is believed to be applicable to other nanosacle carbon materials.     

Self-assemblies of linearly aligned diamond fillers in polysiloxane/diamond composite films with enhanced thermal conductivity

The relocation of diamond fillers was performed in polysiloxane-based composite films under different electric fields. The microscale diamond filler particles were dispersed by sonication in a prepolymer mixture of polysiloxane, followed by high-speed mixing. The homogeneous suspension was cast onto a polyamide spacer of microscale thickness and subjected to three different electric fields: AC, DC, and switched DC, before the mixture became cross-linked. Analysis revealed that self-assemblies of linearly aligned diamond fillers (LADFs) were fabricated in the composite film, connecting the film planes as bridges with different thicknesses depending on the applied electric field. Composites with assemblies of LADFs exhibited enhanced thermal conductivity and electrical insulation, and are attractive for application as thermal interface materials in the semiconductor industry.     

Poly(vinyl alcohol) reinforced with large-diameter carbon nanotubes via spray winding

For practical application of carbon nanotube (CNT)/polymer composites, it is critical to produce the composites at high speed and large scale. In this study, multi-walled carbon nanotubes (MWNTs) with large diameter (∼45 nm) and polyvinyl alcohol (PVA) were used to increase the processing speed of a recently developed spraying winding technique. The effect of the different winding speed and sprayed solution concentration to the performance of the composite films were investigated. The CNT/PVA composites exhibit tensile strength of up to 1 GPa, and modulus of up to 70 GPa, with a CNT weight fraction of 53%. In addition, an electrical conductivity of 747 S/cm was obtained for the CNT/PVA composites. The good mechanical and electrical properties are attributed to the uniform CNTs and PVA matrix integration and the high degree of tube alignment.     

Electrical properties of polyvinylidene fluoride (PVDF)/multi-walled carbon nanotube (MWCNT) semi-transparent composites: Modelling of DC conductivity

Transparent conductive composites can be achieved from PVDF–MWCNT at very low concentration of MWCNT. These composites show different degree of UV–Visible radiation absorption depending on MWCNT concentration in composites. The composition dependent dielectric properties and AC conductivity were also measured for these composites. Properties like AC conductivity, dielectric constant and loss are increasing with filler concentration. The variations of DC conductivity against composition and temperature are also reported. The electrical hysteresis and electrical set are observed for PVDF–MWCNT composites when subjected to heating–cooling cycle. The validity of different theoretical models depicting percolation threshold with respect to DC conductivity was tested for these composites.     

Manufacturing techniques and property evaluations of conductive composite yarns coated with polypropylene and multi-walled carbon nanotubes

This study uses a melt extrusion method, a method for producing wires, to coat polyester (PET) yarns with polypropylene (PP) and multi-walled carbon nanotubes (MWCNTs). The resulting PP/MWCNTs-coated PET conductive yarns are tested for their tensile properties, processability, morphology, melting and crystallization behaviors, electrical conductivity, and applications. The test results indicate that tensile strength of the conductive yarns increases with an increase in the coiling speed that contributes to a more single-direction-orientated MWCNTs arrangement as well as a greater adhesion between PP/MWCNTs and PET yarns. 8 wt% MWCNTs results in an 18 °C higher crystallization temperature (T_c) of PP and an electrical conductivity of 0.8862 S/cm. The test results of this study have proven that this form of processing technology can prepare PP/MWCNTs-coated PET conductive yarns that have satisfactory tensile properties and electrical conductivity, and can be used in functional woven fabrics and knitted fabrics.     

Structure and properties of highly oriented polyoxymethylene/multi-walled carbon nanotube composites produced by hot stretching

Highly-oriented polyoxymethylene (POM)/multi-walled carbon nanotube (MWCNT) composites were fabricated through solid hot stretching technology. With the draw ratio as high as 900%, the oriented composites exhibited much improved thermal conductivity and mechanical properties along the stretching direction compared with that of the isotropic samples before drawing. The thermal conductivity of the composite with 11.6 vol.% MWCNTs can reach as high as 1.2 W/m K after drawing. Microstructure observation demonstrated that the POM matrix had an ordered fibrillar bundle structure and MWCNTs in the composite tended to align parallel to the stretching direction. Wide-angle X-ray diffraction results showed that the crystal axis of the POM matrix was preferentially oriented perpendicular to the draw direction, while MWCNTs were preferentially oriented parallel to the draw direction. The strong interaction between the POM matrix and the MWCNTs hindered the orientation movement of molecules of POM, but induced the orientation movement of MWCNTs.     

Mechanical and electrical properties of carbon nanotube/poly(phenylene sulphide) composites incorporating polyetherimide and inorganic fullerene-like nanoparticles

The mechanical and electrical properties of single-walled carbon nanotube (SWCNT) reinforced poly(phenylene sulphide) (PPS) composites prepared by melt-extrusion have been evaluated. The wrapping of SWCNTs in polyetherimide (PEI) and the addition of inorganic fullerene-like tungsten disulfide (IF-WS₂) nanoparticles provided an effective method for dispersing the SWCNTs, leading to enhanced properties of the resulting hybrid composites. Mechanical tests demonstrated significant enhancements in stiffness, strength and toughness by the addition of both nanofillers, and the Young’s modulus of the hybrid composites was fairly well predicted by two-phase modelling. The electrical conductivity of PPS improved dramatically at low SWCNT content (0.1-0.5 wt%). At higher concentrations, the replacement of part of the SWCNTs with IF-WS₂ maintained the level of conductivity of the composites. Overall, the hybrids possess superior performance than composites reinforced solely with wrapped or non-wrapped SWCNTs, and their properties can be tailored by modifying the SWCNT/IF-WS₂ ratio.     

Segregated poly(vinylidene fluoride)/MWCNTs composites for high-performance electromagnetic interference shielding

Conductive polymer composites (CPCs) that contain a segregated structure have attracted significant attentions because of their promising for fulfilling low filler contents with high electromagnetic interference (EMI) properties. In the present study, segregated poly(vinylidene fluoride) (PVDF)/multi-walled carbon nanotubes (MWCNTs) composites were successfully prepared by mechanical mixing and hot compaction. The PVDF/MWCNTs samples with 7 wt% filler content possess high electrical conductivities and high EMI shielding effectiveness (SE), reaching 0.06 S cm⁻¹ and 30.89 dB (in the X-band frequency region), much higher than lots of reported results for CNT-based composites. And the EMI SE greatly increased across the frequency range as the sample thickness was improved from 0.6 to 3.0 mm. The EMI shielding mechanisms were also investigated and the results demonstrated absorption dominating shielding mechanism in this segregated material. This effective preparation method is simple, low-cost, and environmentally-friendly and has potential industrial applications in the future.     

Effect of imidazolium phosphate and multiwalled carbon nanotubes on thermal stability and flame retardancy of polylactide

A series of composites based on polylactide (PLA), have been prepared by melt-blending with multiwalled carbon nanotubes (MWNT) and Tri(1-hydroxyethyl-3-methylimidazolium chloride) phosphate (IP) functionalized MWNT (MIP). The morphology, thermal stability and burning behavior of the composites were investigated by Field Emission Scanning Electron Microscopy (FESEM), Thermogravimetric Analysis (TGA) and Cone Calorimeter Test (CCT), respectively. Significant improvement in fire retardant performance was observed for the PLA/MIP composite from CCT (reducing both the heat release rate and the total heat release) and TGA (increasing the char residue) compared to PLA/MWNT. SEM and Raman spectroscopy were utilized to explore the surface morphology and chemical structure of the char residues. It revealed that the catalytic charring effect of IP, the physical crosslinking effect of MWNT, and the combined effect of both IP and MWNT (forming continuous and compact char layers) were very efficient in improving the flame retarding properties of PLA/MIP composite.     

Synergistic effect of hybrid graphene nanoplatelet and multi-walled carbon nanotube fillers on the thermal conductivity of polymer composites and theoretical modeling of the synergistic effect

We found that the thermal conductivity of polymer composites was synergistically improved by the simultaneous incorporation of graphene nanoplatelet (GNP) and multi-walled carbon nanotube (MWCNT) fillers into the polycarbonate matrix. The bulk thermal conductivity of composites with 20 wt% GNP filler was found to reach a maximum value of 1.13 W/m K and this thermal conductivity was synergistically enhanced to reach a maximum value of 1.39 W/m K as the relative proportion of MWCNT content was increased but the relative proportion of GNP content was decreased. The synergistic effect was theoretically estimated based on a modified micromechanics model where the different shapes of the nanofillers in the composite system could be taken into account. The waviness of the incorporated GNP and MWCNT fillers was found to be one of the most important physical factors determining the thermal conductivity of the composites and must be taken into consideration in theoretical calculations.     

Piezoresistive and compression resistance relaxation behavior of water blown carbon nanotube/polyurethane composite foam

The in-situ bulk polycondensation process in combination with a ball milling dispersion process was used to prepare the water blown multiwall carbon nanotubes (CNT)/polyurethane (PU) composite foam. The mechanical properties, piezoresistive properties, strain sensitivity, stress and resistance relaxation behaviors of the composite foams were investigated. The results show that the CNT/PU composite foam has a better compression strength than the unfilled polyurethane foams and a negative pressure coefficient behavior under uniaxial compression. The resistance response of CNT/PU nanocomposites foam under cyclic compressive loading was quite stable. The nanocomposite foam containing a weight fraction of carbon nanotubes close to the percolation threshold presents the largest strain sensitivity for the resistance. The characteristic of resistance relaxation of CNT/PU composite foam is different from the stress relaxation due to the different relaxation mechanism. During compressive stress relaxation, the CNT/PU foam composites have excellent resistance recoverability while poor stress recoverability.     

Effects of carbon nanotube aspect ratio on strengthening and tribological behavior of ultra high molecular weight polyethylene composite

Carbon-based nanomaterials are great choice as reinforcement to Ultra-High Molecular-Weight Polyethylene (UHMWPE), with potential use in orthopedics. While high in-plane-stiffness and strength of these nanomaterials help in toughening, their weaker out-of-plane integrity offers lubrication. Present study investigates effect of aspect ratio of carbon nanotubes (CNT) on toughening and solid-lubrication efficiency of UHMWPE-matrix. A nominal 0.05–0.1 wt.% of CNT addition increases hardness and elastic modulus of UHMWPE by 3–45% and 8–42%, respectively. Higher aspect ratio (HAR) CNTs are found more effective in improving hardness and modulus of UHMWPE. Wear rate and friction-coefficient also increase by 530% and 220%, respectively, while reinforced with HAR CNTs. Thermal analysis shows slight increase in crystallinity and stability of composite. HAR CNTs improve interfacial bonding with matrix, due to their morphological similarity to polymer chains, as compared to low aspect ratio CNT. Aspect ratio of CNTs significantly dominates strengthening and tribological behavior of UHMWPE.     

Effect of aspect ratio on thermal conductivity of high density polyethylene/multi-walled carbon nanotubes nanocomposites

This study aims to investigate experimentally the effects of aspect ratio (length/diameter ratio) and concentration of multiwalled carbon nanotubes (MWCNTs) on thermal properties of high density polyethylene (HDPE) based composites. The aspect ratios of two types of MWCNT fillers are in the range of 200–400 and 500–3000. Composite samples were prepared by melt mixing up to weight fraction of 19% filler content, followed by a compression molding. Measurements of density, specific heat and thermal diffusivity (by modulated photothermal radiometry, PTR) were performed and effective thermal conductivities k_e of nanocomposites were calculated using these values. The results show that the composites containing MWCNTs with higher aspect ratio have higher thermal conductivities than the ones with lower aspect ratio. In terms of conductivity enhancement k_e/k_m − 1, the results indicate that MWCNTs with higher aspect ratio provide three to fourfold larger enhancement than the ones with lower aspect ratio, at low filler concentrations.