Fabrication and thermal conductivity of copper matrix composites reinforced with Mo2C or TiC coated graphite fibers

Graphite fiber reinforced Cu-based composites have good thermal conductivity, low coefficient of thermal expansion for heat sink applications. In these composites, the quality of interfacial bonding between the copper matrix and the graphite fibers has significant influence on the thermal properties of composites. In this study, two different carbide coatings (Mo₂C or TiC) were synthesized on graphite fiber to promote the interfacial bonding in composites. Fibers/Cu composites had been produced by spark plasma sintering process. The results showed that the densification, interfacial bonding and thermal conductivity of coated composites were improved distinctly compared to that of uncoated ones. The enhanced composites present 16–44% increase of thermal conductivity in X–Y plane. An original theoretical model was proposed to estimate the interface thermal resistance. The result showed that the interfacial thermal resistance was largely reduced by one order of magnitude with the introduction of carbide interlayer.     

Effect of friction stir welding on microstructure,tensile and fatigue properties of the AA7005/10 vol.%Al2O3p composite

Several studies have been recently focused on friction stir welding of aluminium alloys and some data are also reported on FSW of aluminium-based composites. The application of this solid state welding technique to particles reinforced composites seems very attractive, since it should eliminate some typical defects induced by the traditional fusion welding techniques, such as: gas occlusion, undesidered interfacial chemical reactions between the reinforcement and the molten matrix alloy, inhomogeneous reinforcement distribution after welding. The present work describes the effect of the FSW process on the microstructure and, consequently, on the tensile and low-cycle fatigue behaviour, of an aluminium matrix (AA7005) composite reinforced with 10 vol.% of Al₂O₃ particles (W7A10A). The microstructural characterization evidenced, in the FSW zone, a substantial grain refinement of the aluminium alloy matrix (due to dynamic recrystallization induced by the plastic deformation and frictional heating during welding) and a significant reduction of the particles size (due to the abrasive action of the tool). Tensile tests showed a high efficiency of the FSW joints (about 80% of the ultimate tensile strength). The low-cycle fatigue tests evidenced a fatigue life reduction for the FSW material respect to the base composite, particularly for high values of total strain range. The fracture mechanisms for the FSW specimens were those typical of metal matrix composites: interfacial decohesion, void nucleation and growth, as well as fracture of reinforcing particles, as shown by SEM analyses of the fracture surfaces.     

Development of a novel magnesium-copper based composite with improved mechanical properties

Magnesium based composite with 17.95 wt.% of copper reinforcement was fabricated using an innovative DMD technique followed by hot extrusion. Microstructural characterization of the extruded composite samples showed fairly uniform reinforcement distribution, presence of Mg-Cu based intermetallics, good Cu_P-Mg interfacial integrity, and the presence of minimal porosity. Mechanical properties characterization revealed that the presence of copper as reinforcement lead to a significant increase in hardness, elastic modulus, 0.2% yield strength and UTS of pure magnesium while the ductility was adversely affected. An attempt is made in the present study to correlate the effect of copper as reinforcement with the microstructural and mechanical properties of magnesium.     

Opportunities for new graphitic aluminium metal matrix composite

Abstract

Nickel coated graphite particles have been incorporated into aluminium with a second particulate phase to produce graphitic aluminium metal matrix composites (Gr A-Ni) with improved processing, wear, and scuffing resistance. Excellent wear behaviour is provided by a combination of solid lubrication by graphite as well as high temperature strengthening of the matrix alloy by nickel present as Al₃ Ni intermetallics. Applications being developed include cylinder liners, pistons, connecting rods, various types of brakes, air diffusers and bushings. Neutral buoyancy of two particles, one of which is lighter and the other heavier than the aluminium matrix alloy, makes this a readily sand and die castable material. The presence of graphite and Al₃Ni intermetallics reduces the amount of ceramic particulate required to achieve the desired wear properties, with resulting improved machinability. The composition of the material can be tailored to the application. All these factors influence the finished part cost.     

High shear dispersion technology prior to twin roll casting for high performance magnesium/SiCp metal matrix composite strip fabrication

SiC particulate (SiC_p) reinforced AZ31 magnesium alloy composite strips were produced by a novel process. In the process, a high shear technique was utilised to disperse the reinforcing particles uniformly into the matrix alloy, and AZ31/5 vol%SiC_p slurry was solidified into thin strip by a horizontal twin roll caster. The experimental results showed that the AZ31/5 vol%SiC_p strip obtained with high shear treatment exhibited a significantly refined microstructure and uniform distribution of reinforcing SiC particles. High cooling rate in the TRC process was also considered to contribute to the grain refinement of the matrix alloy, together with the possible heterogeneous nucleation effect of the reinforcing particles. The mechanical properties of the high shear treated composites strips showed enhanced modulus, yield strength and ductility by hardness and tensile tests. The experimental results were discussed in terms of the microstructural features and the macroscopic reliability, where necessary, analytical and statistical analyses were conducted.     

镀铜石墨与铝熔体的润湿性

为了改善石墨与铝的润湿性,通过化学镀使石墨颗粒表面形成完整致密的铜镀层,然后将8%(质量分数)的镀铜石墨粉通过熔体搅拌法加入到铝合金基体中制得金属基复合材料.采用改进的座滴法分别测定了铝熔体与石墨、镀铜石墨的接触角.同时,利用扫描电镜(SEM)对石墨颗粒增强铝基复合材料的微观形貌进行了检测.结果显示,铝熔体与镀铜石墨的接触角为27°,其界面具有良好的润湿性,镀铜石墨粉在铝合金基体中分布均匀.     

Thermo-mechanical properties of poly(vinylidene fluoride) modified graphite/poly(methyl methacrylate) nano composites

Poly(methyl methacrylate) (PMMA) nano composites were synthesized by melt compounding technique. Different graphite loadings were investigated, including some treated with poly(vinylidene fluoride) (PVDF). A homogeneous dispersion of graphite throughout the PMMA matrix was observed under microscopic analysis. Thermo-gravimetric analysis showed the incorporation of graphite resulted in improvement of thermal stability of neat PMMA. Dynamic mechanical thermal analysis also showed a significant improvement in the storage modulus over the temperature range of 25–150 °C. Coating the graphite with a small amount of PVDF was found to further extend the improvement in the modulus of the PMMA nano composite at 1 wt.% graphite loading.     

Mechanical and tribological properties of LM13/TiO2/MoS2 hybrid metal matrix composite synthesized by stir casting

This paper involves the fabrication of LM13/TiO₂ (12?wt%)/MoS₂ (3?wt%) hybrid metal matrix composite and unreinforced alloy using liquid metallurgy route and evaluation of mechanical properties and adhesive wear characteristics. Microstructural investigation revealed homogeneous distribution of reinforcements in matrix. Hardness and tensile properties revealed that the composite had attained an improvement of 16.5 and 35%, respectively, over alloy. Wear characteristics were analyzed using pin-on-disk tribometer by varying load (10–40?N), sliding velocity (1–4?m/s), and sliding distance (500–2000?m). Statistical analysis was performed using response surface methodology to obtain the optimum wear process parameters for achieving maximum wear resistance. Results revealed that, with increasing load and sliding velocity, an increment in wear rate was observed for both alloy and composite, while a decline was observed with increasing sliding distance for composite and vice versa for alloy. Worn surface analysis revealed that load plays a prominent role in deciding wear rate, followed by sliding velocity. Sliding distance had less effect on wear rate of composite while it had significance on alloy. This hybrid composite can replace the conventional material used in automotive applications involving tribological importance.     

Microstructure and mechanical properties of Al–2Mg alloy base short steel fiber reinforced composites prepared by vortex method

Fabrication and characterization of cast Al–2Mg alloy matrix composites reinforced with short steel fibers are dealt with in the present study. Three types of steel fiber were used: uncoated, copper coated and nickel coated. All the composites were prepared by the liquid metal route using vortex methods. When tested in tension, all composites exhibited improvement in strength due to high relative strength of steel fibers. The ductility was lowered except for the composite with copper coated fibers. Copper coated fiber reinforced composites gave the highest strength. Higher strength accompanied with appreciable ductility demonstrated by composites with copper coated fibers is attributed to the solid solution and fiber strengthening as well as good bonding at the interface. Composites reinforced with uncoated and Ni coated steel fibers did not exhibit strengthening to the level exhibited with copper coated fibers because brittle intermetallic phases are formed at the interface. These phases promote initiation and facilitate propagation of cracks. The observed fracture mechanism of composites was dimple formation, fiber breakage and pullout of fibers. Fracture surface of uncoated and Ni coated composites showed extensive pull out of fibers as well as fiber breakage confirming the above inference. In case of the copper coated composites dimple formation and coalescence was more extensive. EDX analysis showed a build up Cu, Ni, and Fe at the interface.     

Influence of carbon nanotubes and dispersions of SiC on the physical and mechanical properties of pure copper and copper‐nickel alloy

This paper investigates the physical and mechanical properties of copper‐nickel alloy (at 50 wt.%–50 wt.%) and pure copper, mixed with various types of reinforcement materials such as carbon nanotubes (0.5 wt.%–2 wt.%) as nanoparticles, silicon carbide (1 wt.%–4 wt.%) as microparticles. The acquired composite specimens characteristics were estimated such as microstructure, density, electrical and thermal conductivity, hardness, and compression stress properties to determine the suitable reinforcement percentage that has the best physical and mechanical properties with different main matrix material whether copper‐nickel mechanical alloying or pure copper powder. The micron‐sized silicon carbide and nanosized carbon nanotubes were added to improve the mechanical and physical properties of the composite. The electrical and thermal conductivity of pure copper alloy enhanced compared with the copper‐nickel alloy matrix material. The hardness and compression yield stress of both pure copper and copper‐nickel composites have enhancement values and for copper‐nickel base composites hardness and compression yield stress have enhanced with the most positive enhancement values to examined an optimum percentage of reinforcing material.     

Effects of copper addition on the sintering behavior and mechanical properties of powder processed Al/SiC<Subscript><Emphasis Type="Bold">p</Emphasis></Subscript> composites

The effect of copper addition on powder processed Al-10 vol% SiC composites was studied in regards to their sintering responses. Copper was mixed with aluminum powder either as elemental powders or as the coated layer on SiC particles. After sintering at 600°C for 1 h, Al-SiC composites with no copper addition showed little densification. It also demonstrated very low bend strengths of 49 and 60 MPa, indicating poor bonding between the powders in the sintered composite. The addition of 8% copper to the Al/SiC system effectively improved the sintering response, producing over 95% theoretical density, a bend strength of 231 MPa with the copper coated SiC, and a 90% density with over 200 MPa bend strength with the admixed copper.The as-sintered microstructures of the Al–SiC composites clearly revealed particle boundaries and sharp pores, indicating that only a limited neck growth occurred during sintering. In the case of Al–Cu–SiC composites, however, a liquid phase was formed and spread through particle boundaries filling the interfaces or voids between SiC particles and the matrix powders. The coated copper on SiC particles produced a somewhat better filling of the interface or voids, resulting in a little more densification and better sintered strength. Since the solubility of copper in aluminum is less than 2% at the sintering temperature, the alloying of copper in the aluminum matrix was limited. Most of the copper added was dissolved in the liquid phase during the sintering and precipitated as CuAl₂ phase upon cooling.     

Preparation of graphene nanosheet/alumina composites by spark plasma sintering

Graphene nanosheet/alumina composite has been prepared by spark plasma sintering. A homogeneous distribution of nanosheets in an alumina matrix could be obtained by the electrostatic attraction between graphite oxide and alumina particles and their subsequent reduction. The introduction of graphene nanosheet leads to refinement of grain size of alumina after hot pressing. The experimental results have shown that the fracture toughness and conductivity of the graphene nanosheet/alumina composite are about 53% and 13 orders of magnitude higher than those of unreinforced alumina material, respectively.     

Fabrication of nano-sized Al2O3 reinforced casting aluminum composite focusing on preparation process of reinforcement powders and evaluation of its properties

In this study, a novel approach was used to fabricate Al₂O₃ nanoparticle reinforced aluminum composites to avoid agglomeration of nanoparticles in matrix. Al₂O₃ nanoparticles were separately milled with aluminum and copper powders at different milling durations and incorporated into A356 alloy via stir casting method. The effects of milling process and milling time on mechanical properties of the composites were evaluated by hardness, tensile, and compression tests. Based on the results, some of the composites, reinforced with Al₂O₃-metallic mixed powders, showed higher mechanical performance compared with that of the pure Al₂O₃ nanoparticle reinforced composite. This enhancement is related to uniform distribution of individual nanoparticles and grain refinement of A356 matrix, shown in microstructural studies. Moreover, the results showed that an increase in milling time, led to a gradual decrease in mechanical performance of the samples. It can be related to further oxidation of metallic powders that can act as inclusions and also further probable contamination of nanoparticles with increase in milling time. Studies on the fracture surfaces revealed that the failure of matrix was the basic mechanism of fracture in the composites. Agglomerated nanoparticles were observed on dendrites in the fracture surface of the Al₂O₃–Al reinforcement samples.     

A magnesium alloy matrix composite reinforced with metallic glass

Novel light-weight materials of advanced performance are now experiencing global interest due to the strong need to reduce energy consumption in land and air transportation sectors. Here we report on a novel magnesium alloy matrix composite material. The reinforcing phase in the magnesium alloy is a fine dispersion of metallic glass particles. The composite is sintered from the powder mixture of the alloy and metallic glass at a temperature slightly above the glass transition T_g of the metallic glass particles that is close to the Mg alloy’s solidus temperature. At the compaction temperature, the metallic glass acts as a soft liquid-like binder but upon cooling it becomes the hard reinforcement component of the composite. Processing, microstructure and mechanical properties of the composite are discussed.     

Tyranno ZMI fiber/TiSi2–Si matrix composites for high-temperature structural applications

A Tyranno ZMI fiber/TiSi₂–Si matrix composite was fabricated via melt infiltration (MI) of a Si–16at%Ti alloy at 1375 °C under vacuum. The Si–Ti alloy was used as an infiltrant to conduct MI processing below 1400 °C and inhibit the strength degradation of the amorphous SiC fibers. The alloy matrix formed was dense and comprised primarily of TiSi₂–Si eutectic structures. The TiSi₂–Si matrix composite melt-infiltrated at 1375 °C showed a pseudo-plastic tensile stress–strain behavior followed by final fracture at ∼290 MPa and ∼0.9% strain. When the MI temperature was increased to 1450 °C, however, substantial reduction in the stiffness and ultimate strength occurred under tensile loading. Microstructural observations revealed that these degradations were attributed to the damages that occurred on the reinforcing fibers and pyrolytic carbon interfaces during the MI process. The present experimental results clearly demonstrated the effectiveness of the low-temperature MI process in strengthening Tyranno ZMI fiber composites and reducing the processing cost.     

Elastic moduli,thermal expansion and microstructure of copper-matrix composite reinforced by continuous graphite fibres

Copper-matrix composites reinforced by continuous graphite fibres (C_g) were processed by hot-pressing layers of metallic prepregs, each fibre within the yarns having previously been coated with copper by electroplating. The electrodeposition and consolidation conditions were optimized to minimize the residual porosity, which could be considered as negligible. One-dimensional (1D) and two-dimensional composites were obtained by this technique. In addition to the good metallurgical quality of the matrix, examination of the fibre/matrix interphase by Auger electron spectroscopy confirmed the excellent chemical compatibility between copper and graphite. As a consequence, the ultimate tensile strength of fibres extracted from the matrix remained nearly unchanged. The thermal expansion coefficients of 1 D C_g/Cu composite materials were determined between 100 and 300°C, along the two orthogonal directions. Values ranging from 8 to 9 × 10⁻⁶ °C⁻¹ in the composite plane and from 16 to 18 × 10⁻⁶ °C⁻¹ in the orthogonal direction were obtained. These results, which are related to the strong anisotropy of the ex-pitch graphite fibre, are correlated to the theoretical values found with the rule of mixtures. The poor Young's modulus and the tensile strength values are correlated to the microstructure of the fibre/matrix interphase.     

Nano-sized aluminum oxide reinforced commercial casting A356 alloy matrix: Evaluation of hardness,wear resistance and compressive strength focusing on particle distribution in aluminum matrix

Achieving a uniform distribution of reinforcement within the matrix is a challenge which impacts directly on the properties and quality of the composite material. In the present study a fabrication and evaluation approach was used focusing on particle distribution in metal matrix. Al and Cu powders were separately milled with nano-Al₂O₃ particles and incorporated into A356 alloy via vortex method to produce cylindrical A356/nano-Al₂O₃ composites. The stirring was carried out in various durations. The variations of density, hardness, compressive strength, and wear resistance were measured throughout the cylindrical samples. The evaluation of mechanical properties and microstructural studies showed that an increase in stirring time led to a more uniform dispersion of particles in the matrix and also led to a decrease in mechanical properties due to an increase in porosity content of the composites compared with those of the samples stirred for shorter durations. Moreover, milling process affected particle distribution. Nanoparticles more uniformly dispersed in the Al₂O₃–Cu reinforced samples compared with that of the samples reinforced with Al₂O₃–Al or pure alumina powders.     

Microstructure investigations and mechanical properties of an Al‐Al2O3 MMC produced by semi‐solid solidification

The influence of the semi‐solid solidification production parameters (shear rate and agitation time) and the concentration of reinforcing particles on the microstructure formation and mechanical properties of a 520 aluminum alloy reinforced with Al₂O₃ particles was investigated. Depending on the content of reinforcing particles and the stirring conditions different rosette structures were formed. The type of wear mechanism (delamination or adhesion) depends on the size of the rosettes and the distribution of Al₂O₃ reinforcements. Best mechanical properties were obtained for metal matrix composites reinforced with 12 wt% of Al₂O₃ stirred at a shear rate of 2100 s^–1 for 1800 s. These samples showed tensile strength and yield stress similar to the commercial A520 alloy. The hardness and wear resistance were improved by the addition of Al₂O₃ particles, meanwhile the elongation to fracture was reduced.     

Processing and Characterization of In Situ (TiC–TiB2)p/AZ91D Magnesium Matrix Composites

In this paper, a practical and cost‐effective processing route, in situ reactive infiltration technique, was utilized to fabricate magnesium matrix composites reinforced with a network of TiC–TiB₂ particulates. These ceramic reinforcement phases were synthesized in situ from Ti and B₄C powders without any addition of a third metal powder such as Al. The molten Mg alloy infiltrates the preform of (Ti_p + B₄C_p) by capillary forces. The microstructure of the composites was investigated using scanning electron microscope (SEM)/energy dispersive X‐ray spectroscopy (EDS). The compression behavior of the composites processed at different conditions was investigated. Also, the flexural strength behavior was assessed through the four‐point‐bending test at room temperature. Microstructural characterization of the (TiB₂–TiC)/AZ91D composite processed at 900 °C for 1.5 h shows a relatively uniform distribution of TiB₂ and TiC particulates in the matrix material resulting in the highest compressive strength and Young's modulus. Compared with those of the unreinforced AZ91D Mg alloy, the elastic modulus, flexural and compressive strengths of the composite are greatly improved. In contrast, the ductility is lower than that of the unreinforced AZ91D Mg alloy. However, this lower ductility was improved by the addition of MgH₂ powder in the preform. Secondary scanning electron microscopy was used to investigate the fracture surfaces after the flexural strength test. The composites show signs of mixed fracture; cleavage regions and some dimpling. In addition, microcracks observed in the matrix show that the failure might have initiated in the matrix rather than from the reinforcing particulates.     

Investigation of microstructure and mechanical properties of steel fibre–cast iron composites

Abstract

The aim of the present experimental study was to investigate improvement of the toughness and strength of grey cast iron by reinforcing with steel fibres. The carbon content of the steel fibres was chosen to be sufficiently low that graphite flakes behaving as cracks were removed by carbon diffusion from the cast iron to the steel fibres during the solidification and cooling stages. To produce a graphite free matrix, steel fibres with optimum carbon content were used and the reinforced composite structure was cast under controlled casting conditions and fibre orientation. Three point bend test specimens were manufactured from steel fibre reinforced and unreinforced flake graphite cast iron and then normalising heat treatments were applied to the specimens at temperatures of 800 and 850°C. The fracture toughness and strength properties of the steel fibre reinforced material were found to be much better than those of unreinforced cast iron. The microstructures of the composite at the fibre–matrix transition zone were examined.