稀土Y元素对铸态镁合金组织与力学性能的影响

采用熔炼工艺制备了Mg-2.0Zn-0.2Ca与Mg-2.0Zn-0.2Ca-2Y合金,研究了两种合金的铸态组织及力学性能。结果表明,Y元素的添加细化了Mg-2.0Zn-0.2C合金的铸态组织。Mg-2.0Zn-0.2Ca合金主要由α-Mg与少量Mg₇Zn₃相组成,添加2wt%的Y后,改变了Zn在Mg基体中的固溶度,降低了其固溶强化效果,同时组织中形成了I相和W相。添加Y元素后,合金的规定塑性延伸强度升高,从41.0 MPa升高到50.6 MPa;伸长率降低,从12.6%降低到4.0%。     

钕对二元高铝镁合金组织及性能的影响

研究了稀土元素钕对Mg-15Al合金显微组织和力学性能的影响。试验结果表明:加入钕后,Mg-15Al合金的α-Mg晶粒明显细化,α+β共晶组织由粗大网状变得分散、细小,钕与铝结合形成稳定的Al11Nd3,合金的抗拉强度和伸长率均得到显著提高。钕加入量为1.0%时,组织细化效果最好,Mg-15Al合金的综合力学性能达到最佳。当钕加入量为1.5%时,α-Mg晶粒又变大、抗拉强度略有下降。     

Ca对Mg-5Al-1Bi合金显微组织和力学性能的影响

使用X射线衍射仪、金相显微镜、扫描电镜、能谱仪及力学性能测试等试验手段,研究了Ca含量对铸态Mg-5Al-1Bi镁合金显微组织和力学性能的影响。结果表明,铸态Mg-5Al-1Bi镁合金由α-Mg基体和β-Mg17Al12相组成,加入Ca后,合金晶粒细化,β-Mg17Al12相的数量减少,由连续变得较为分散。当Ca含量达到3%时,合金中生成新的第二相Al2Ca。高熔点相Al2Ca在高温条件下能钉扎晶界,阻碍晶界滑移,有利于提高合金的高温蠕变性能。合金硬度和屈服强度随着Ca含量的增加而提高,而抗拉强度和伸长率下降。     

Sm对AM60合金显微组织和力学性能的影响

借助光学显微镜、扫描电镜、X射线衍射仪和DNS100电子万能试验机研究AM60合金中加入Sm后的显微组织和力学性能,并分析Sm对合金显微组织和力学性能的影响。结果表明,添加元素Sm可以细化镁合金的晶粒,改变β相的形态和大小,从连续或断续网状、长条状,变为卵石状或颗粒状均匀弥散分布在α-Mg基体上,显著改善合金的显微组织。Sm的加入可形成稳定性较高的颗粒状Al2Sm高温化合物相。随着Sm含量的增加,合金的抗拉伸强度和伸长率呈现先升后降的趋势,当Sm含量为1.0%(质量分数,下同)时抗拉伸强度和伸长率分别达到最大值210MPa和6.9%。室温下AM60合金的断口呈解理断裂,加入Sm变质后其断口形貌表现为准解理+局部韧性断裂特征。     

不同合金元素对Mg15Al高铝镁合金组织与性能的影响

研究了不同合金元素（Zn,Nd,Si）对Mg15Al镁合金的组织和性能的影响。通过对Mg15Al,Mg15Al1Zn,Mg15Al1Si,Mg15Al1．5Nd四种合金微观组织的观察和力学性能的测定,发现添加了合金元素后Mg合金组织中α—Mg基体和β—Mg17Al12相都得到了不同程度的细化,其中Mg15Al1Si,Mg15Al1．5Nd合金组织中有第三相生成,其形态分别为汉字状、块状,长针状。试验结果表明：添加zn和Nd元素后,抗拉强度比Mg15Al合金显著提高。提高幅度分另4为：13．2％和16．6％,而添加si元素后Mg15Al1Si合金抗拉强度比Mg15Al合金低。添加Nd元素后,伸长率比Mgl5Al合金显著提高,增幅为140％,添加了Si元素和Zn元素后,伸长率比Mg15Al合金低。     

Effect of element Gd on phase constituent and mechanical property of Mg-5Sn-1Ca alloy

The Mg-5Sn-1Ca-xGd (x=0, 1) alloys were chosen to investigate the change in solidification paths, phase formation and mechanical properties. The microstructure of as-cast Mg-5Sn-1Ca alloy is composed of α-Mg, Mg2Sn and CaMgSn phases. With the addition of Gd, the formation of the Mg2Sn phase is impeded and the CaMgSn phase is refined, whereas the ultimate tensile strength and elongation decrease. The possible reasons for the variation in microstructure and mechanical properties were discussed.     

Mg-6Gd-3Y-2Zn-0.5Zr镁合金的组织和性能

设计了新型Mg-6Gd-3Y-2Zn-0.5Zr镁合金,并用光学显微镜、扫描电镜及拉伸试验机对合金铸态、均匀化态及挤压态的显微组织特征和力学性能进行了研究。结果表明,铸态Mg-6Gd-3Y-2Zn-0.5Zr合金组织主要由α-Mg基体和沿晶界分布的块状长周期堆垛有序结构相组成,均匀化处理(450℃×16h)促使细小层片状的长周期堆垛有序结构相由晶界向晶内生长。挤压态Mg-6Gd-3Y-2Zn-0.5Zr合金在200℃下时效处理,无明显时效硬化现象,但挤压态合金具有优良的强韧性能,室温抗拉强度、屈服强度和伸长率分别为335MPa、276MPa和17%。     

等通道转角挤压制备超细晶Mg15Al双相合金组织与性能

对高铝双相合金Mg15Al在553K以Bc路线进行了不同道次的等通道挤压(ECAP),获得了超细晶高铝镁合金。通过OM,SEM,TEM分析了ECAP前后合金的微观组织结构及断口形貌,并测试了不同挤压道次后合金的硬度和室温拉伸性能,分析了ECAP细化晶粒机理及其性能改善原因。结果表明,随挤压道次增加,累计形变增强,网状硬脆相β-Mg17Al12破碎,合金晶粒显著细化,但对单相区和两相混合区细化效果不同。在α、β两相共存区内,4道次ECAP后形成100nm～200nm的细晶粒;在α单相区,4道次ECAP后晶粒为1μm以下,且在初晶α-Mg内析出弥散细小的β相,起到细晶强化和弥散强化作用。8道次ECAP后,晶粒略有长大。ECAP使合金的硬度、抗拉强度和延伸率同时得到提高,尤其是4道次ECAP后,硬度提高了32.04%,抗拉强度σb从150MPa提高到269.3MPa,延伸率δ由0.05%提高到7.4%;8道次ECAP后,硬度、抗拉强度略有下降,延伸率略有上升。SEM断口观察显示ECAP使合金拉伸断口形貌由铸态的解理断裂特征转变为延性韧窝断裂特征。     

Ce含量对Mg-Li-Al-Zn合金显微组织和拉伸性能的影响(英文)

制备了Mg-5Li-3Al-2Zn-xCe(x=0-2.5;质量分数,%)铸态合金,并将所得合金分别于300°C和370°C进行均匀化和固溶处理;研究固溶处理后合金显微组织和拉伸性能的变化。结果表明,合金中加入Ce后出现Al2Ce/Al3Ce析出相,此时合金主要由α-Mg、Al2Ce、Al3Ce和AlLi相组成;固溶处理后合金中AlLi和Al-Ce析出相数量减少。析出相的数量与形态对合金的力学性能十分重要,含有1.0%Ce的合金获得了优良的拉伸性能。固溶处理后Mg-5Li-3Al-2Zn-0.5Ce合金的强度和伸长率都得到了大幅度的提高,这是因为合金在固溶处理后由于基体中的溶质原子增加而获得良好的固溶强化作用。     

微量元素Sr对AM60B镁合金组织和性能的影响

利用光学显微镜(OM)、场发射扫描电子显微镜(FESEM)、电子万能试验机、数显洛氏硬度计和显微硬度仪研究微量Sr对镁合金AM60B的铸态组织和力学性能的影响。结果表明,添加微量元素Sr可以细化镁合金的晶粒,而不改变基体α-Mg相的枝晶形貌,但可改变γ相的形态和大小,从连续或断续网状、长条状,变为卵石状或颗粒状。Sr对AM60B镁合金的抗拉强度和延伸率的影响具有相似的趋势,即随着Sr含量的增加,合金的抗拉强度和延伸率呈现先升后降的趋势,当Sr含量为0.05%时抗拉强度和延伸率分别达到最大值191.82MPa和4.63%,而洛氏硬度和显微硬度随着Sr含量的增加而增大。AM60B镁合金断裂方式存在着由解理断裂向准解理断裂再向解理断裂转化的模式。     

Influence of aging modes on microstructure and mechanical properties of AZ80 magnesium alloy

The microstructure and mechanical properties of AZ80 magnesium alloy after solid solution and aging treatments were studied by using optical microscope (OM), X-ray diffraction (XRD), scanning electron microscopy(SEM) as well as tensile testing. The results indicated that β-Mg17Al12 phase was getting to distribute discontinuously along the grain boundary after treated at 395℃ ageing for 12 h followed by water-cooling, but it did not dissolve into α-Mg completely. The residual β-Mg17Al12 phase distributed along the grain boundary and had block-like or island shapes. The size of α-Mg was getting to be coarsening but not significantly. The β-Mg17Al12 precipitates appeared in discontinuous and continuous patterns from supersaturated α-Mg solid solution after aged at 200℃. The precipitation patterns were associated with the aging time essentially. The tensile strength and elongation of the alloy increased significantly but the hardness and yield strength decreased after solid solution treatment. However, with the prolonging of aging time, the hardness and strength of alloy increased while the ductility decreased.     

Enhancement of mechanical properties of duplex Mg-9Li-3Al alloy by Sn and Y addition

For enhancement of mechanical properties in Mg-9Li-3Al alloys, Mg-9Li-3Al duplex alloys were alloyed by addition of Sn and Y. Microstructure evolution and mechanical property response of as-cast Mg-9Li-3Al alloys by alloying with Sn and Y were investigated by optical microscopy, scanning electron microscopy, X-ray diffractometry and tensile tests. The results indicate that considerable blocky dendrites of primary α phase in Mg-9Li-3Al alloys become lath-like due to the addition of Sn. With addition of Y, Mg-9Li-3Al alloy consists of both block-like and lath-like α-Mg dendrites. The as-cast Mg-9Li-3Al-1Sn-1Y alloy shows a yield strength of 118 MPa, ultimate tensile strength of 148 MPa and the elongation to failure of 21%. Improvement in both strength and elongation of Mg-9Li-3Al alloys with Sn and Y addition is attributed to the combined action of MgLi₂Sn and Al₂Y intermetallic compounds.     

Ca对ZA63合金组织和力学性能的影响

通过合金制备、微观分析和力学性能测试等方法研究了Ca对ZA63合金微观组织和力学性能的影响.结果表明,当加入Ca元素后,舍金晶粒细化,半连续网状的τ相变为细小粒状或棒状,颗粒状τ相更为细小,并形成了细小高熔点Al_2Ca相.随着Ca含量的增加,固溶时效态合金在室温、150℃和175℃温度下的抗拉强度和延伸率基本上呈先升高后降低的趋势.当Ca含量为1.0%时,合金在各温度下的抗拉强度和延伸率都达到最大值.     

Zn含量对铸态Mg-2Er合金的微观结构及力学性能影响

采用XRD和SEM等微观表征技术研究不同Zn添加量对Mg-2Er合金微观组织和力学性能的影响。结果表明：当Zn添加量为1%和2%时,合金主要相组成为W相和α-Mg;当Zn添加量为4%-10%时,合金中则有I相析出,合金相成分变为W相、I相和α-Mg;当Zn添加量增加至12%时,W相消失,合金中主要第二相则为I相和Mg4Zn7相。当Zn添加量为6%时,合金具有较好的拉伸力学性能,其抗拉强度、屈服强度和伸长率分别为224 MPa、134 MPa和10.4%。     

锆对铸造3104铝合金微观结构和力学性能的影响

研究了不同锆添加量的3104合金的析出组织和力学性能。结果表明,随着Zr含量的增加,合金晶粒尺寸减小,当Zr质量分数大于或等于0.25%时,合金晶粒最小(20μm)。同时,晶粒形状由羽毛状变为等轴状。此外,Zr还可以通过形成Si相和其它金属间化合物来改善合金中Si和Mn元素的分布。维氏硬度分析表明,Zr的加入会降低Al-Mn-Fe 3104合金的硬度。此外,根据拉伸试验结果,当Zr质量分数不高于0.25%时,随着Zr含量的增加,合金的抗拉伸强度和延伸率都有所提高。适当的Zr含量可以起到钉扎位错和阻碍滑移的作用,提高合金的强度和韧性。     

Mn含量对Mg-5Al合金铸态组织和力学性能的影响

研究了合金元素Mn对Mg-5Al合金铸态组织和力学性能的影响。结果表明,在Mg-5Al合金中加入Mn后,合金组织细化,连续或半连续网状分布的β-Mg17Al12相逐渐转变为断续、分散的骨骼状相,晶界附近出现颗粒相并且数量逐渐增多。随着Mn含量增加,合金室温抗拉强度、伸长率及冲击韧度先上升然后下降。当Mn含量为0.3%时,合金综合力学性能最好,抗拉强度、伸长率与冲击韧度达到190MPa、7.3%与21.1J·cm-2,分别提高了7.9%、9.1%与9.3%。继续增加Mn含量至0.5%时,Al8Mn5颗粒聚集长大粗化,导致Mg-5Al合金综合力学性能下降。     

Mg-6Zn—xCu铸造合金的显微组织及力学性能研究

采用金属型铸造方法制备了Mg-6Zn-xCu（x=1％、3％、5％）镁合金,并通过光学显微镜、X射线衍射和扫描电镜及力学性能测试等手段研究了Cu含量对合金的显微组织和力学性能的影响。结果表明：Cu在合金中主要以CuMgZn相存在,且随着Cu量的增加,其数量增加;在凝固过程中,CuMgZn富集在已结晶的α-Mg表面,阻碍了其长大,从而细化了晶粒,但过量的CuMgZn偏聚晶界偏聚,引起局部的应力集中,对合金的力学性能产生负面影响;随着Cu含量的增加,合金的力学性能逐渐降低,加入1％Cu时,合金的抗拉强度和伸长率达到最大值,分别为208MPa和13．5％;随着Cu含量的增加,拉伸断口由准解理断裂向解理断裂和沿晶断裂转变。     

Effects of yttrium addition on microstructure and mechanical properties of as-extruded AZ31 magnesium alloys

The effects of yttrium addition on microstructure and mechanical properties of as-extruded AZ31 magnesium alloys were investigated by OM,XRD and SEM.The results show that the addition of yttrium results in the formation of a new phase,Al_2Y. When the addition of yttrium is higher than 1.48%-2.91%(mass fraction),another new phase,Al_3Y_5Mn_7,forms,and the amount ofβ-Mg_(17)Al_(12) phase in the AZ31 alloy decreases sharply.The tensile test at room temperature indicates that the yield strength of as-extrude...     

Sr含量对Mg-Li-Al-Mn合金显微组织及力学性能的影响

利用真空感应炉在氩气保护下,设计与制备Mg-8Li-3Al-0.5Mn-xSr（x=0-1.0）合金,并将其进行热挤压处理。分别研究合金铸态与挤压态显微组织和拉伸性能。结果表明：LAM830合金主要含有α-Mg,β-Li,Al2Mn3和LiMgAl2相。在加入Sr后合金中出现Al-Sr析出相。Sr对铸态合金α-Mg基体的二次枝晶臂有明显细化效果。经过热挤压处理的合金组织远优于铸态的合金组织。金属间化合物的含量与形态对合金力学性能的影响很大,其中挤压态的LAM830-0.5Sr具有最佳的伸长率（22.43%）,LAM830-0.75Sr合金具有最佳的抗拉强度（265.46 MPa）。     

Ultrasonic Vibration and Rheocasting for Refinement of Mg–Zn–Y Alloy Reinforced with LPSO Structure

In this work, ultrasonic vibration (UV) and rheo-squeeze casting was first applied on the Mg alloy reinforced with long period stacking ordered (LPSO) structure. The semisolid slurry of Mg–Zn–Y alloy was prepared by UV and processed by rheo-squeeze casting in succession. The effects of UV, Zr addition and squeeze pressure on microstructure of semisolid Mg–Zn–Y alloy were studied. The results revealed that the synergic effect of UV and Zr addition generated a finer microstructure than either one alone when preparing the slurries. Rheo-squeeze casting could significantly refine the LPSO structure and α-Mg matrix in Mg_96.9Zn₁Y₂Zr_0.1 alloy without changing the phase compositions or the type of LPSO structure. When the squeeze pressure increased from 0 to 400 MPa, the block LPSO structure was completely eliminated and the average thickness of LPSO structure decreased from 9.8 to 4.3 μm. Under 400 MPa squeeze pressure, the tensile strength and elongation of the rheocast Mg_96.9Zn₁Y₂Zr_0.1 alloy reached the maximum values, which were 234 MPa and 17.6%, respectively, due to its fine α-Mg matrix (α1-Mg and α2-Mg grains) and LPSO structure.