Preferential oxidation of CO over CuO/CeO2 and Pt-Co/Al2O3 catalysts in micro-channel reactors

Micro-channel plates with dimension of 1 mm × 0.3 mm × 48 mm were prepared by chemical etching of stainless steel plates followed by wash coating of CeO₂ and Al₂O₃ on the channels. After coating the support on the plate, Pt, Co, and Cu were added to the plate by incipient wetness method. Reaction experiments of a single reactor showed that the micro-channel reactor coated with CuO/CeO₂ catalyst was highly selective for CO oxidation while the one coated with Pt-Co/Al₂O₃ catalyst was highly active for CO oxidation. The 7-layered reactors coated with two different catalysts were prepared by laser welding and the performances of each reactor were tested in large scale of PROX conditions. The multi-layered reactor coated with Pt-Co/Al₂O₃ catalyst was highly active for PROX and the outlet concentration of CO gradually increased with the O₂/CO ratio due to the oxidation of H₂ which maintained the reactor temperature. The multi-layered reactor coated with CuO/CeO₂ showed lower catalytic activity than that coated with Pt catalyst, but its selectivity was not changed with the increase of O₂/CO ratios due to the high selectivity. In order to combine advantages (high activity and high selectivity) of the two individual catalysts (Pt-Co/Al₂O₃, CuO/CeO₂), a serial reactor was prepared by connecting the two multi-layered micro-channel reactors with different catalysts. The prepared serial reactor exhibited excellent performance for PROX.     

Pt/Al_2O_3与Pt/MgO-Al_2O_3催化剂制备及其催化氢能载体甲基环己烷脱氢反应性能

以碱共沉淀法制备Mg-Al水滑石,然后采用浸渍法负载活性组分Pt,经焙烧、氢气还原得到Pt/Al_2O_3与Pt/Mg O-Al_2O_3催化剂,采用XRD、N2吸附-脱附、FT-IR、H2-TPR和Py-IR等分析Mg O的加入对Pt/Al_2O_3催化剂结构性能的影响,并在甲基环己烷连续脱氢反应中对比两种催化剂活性。结果表明,Pt/Mg O-Al_2O_3催化剂比表面积小于Pt/Al_2O_3催化剂,且表面基本无酸性活性中心,但表现出与Pt/Al_2O_3催化剂相同的脱氢活性。在Pt负载质量分数2%、催化剂用量0.5 g、甲基环己烷0.1 m L·min-1纯样进料和325℃反应10 h后,原料平均转化率79.9%,脱氢产物只有甲苯,对应的产氢速率192.8 mmol·(g-metal·min)-1,表现出优良的脱氢活性。     

助剂Ba对Pd/Al_2O_3和Pt/Al_2O_3催化剂的C1-C3烷烃催化燃烧性能的影响

通过浸渍法制备了Al_2O_3负载的Pd和Pt催化剂,考察催化剂的甲烷、乙烷和丙烷催化燃烧活性,以及助剂Ba对催化性能的影响。对于Pd/Al_2O_3催化剂,加入Ba使活性物种PdO颗粒变大和还原温度升高,形成更稳定的PdO活性物种,是Pd-Ba/Al_2O_3催化剂活性提升的主要原因。对于Pt/Al_2O_3催化剂,加入Ba助剂使活性物种Pt0含量降低,PtO_x与Al_2O_3载体相互作用增强,使PtO_x物种更难被还原为Pt~0,导致Pt-Ba/Al_2O_3催化剂活性降低。Pd和Pt催化剂催化烷烃氧化反应活性规律一致:丙烷乙烷甲烷。Pd/Al_2O_3催化剂有利于C—H键活化,Pt/Al_2O_3催化剂有利于C—C键活化。Pt/Al_2O_3催化剂对C1-C3烷烃氧化活性的差别明显大于Pd/Al_2O_3催化剂。Pt/Al_2O_3催化剂对碳比例高的烷烃活性更高。     

Design of a novel bifunctional catalyst IrFe/Al2O3 for preferential CO oxidation

In this study, a novel bifunctional catalyst IrFe/Al₂O₃, which is very active and selective for preferential oxidation of CO under H₂-rich atmosphere, has been developed. When the molar ratio of Fe/Ir was 5/1, the IrFe/Al₂O₃ catalyst performed best, with CO conversion of 68% and oxygen selectivity towards CO₂ formation of 86.8% attained at 100 °C. It has also been found that the impregnation sequence of Ir and Fe species on the Al₂O₃ support had a remarkable effect on the catalytic performance; the activity decreased following the order of IrFe/Al₂O₃ > co-IrFe/Al₂O₃ > FeIr/Al₂O₃. The three catalysts were characterized by XRD, H₂-TPR, FT-IR and microcalorimetry. The results demonstrated that when Ir was supported on the pre-formed Fe/Al₂O₃, the resulting structure (IrFe/Al₂O₃) allowed more metallic Ir sites exposed on the surface and accessible for CO adsorption, while did not interfere with the O₂ activation on the FeO_x species. Thus, a bifunctional catalytic mechanism has been proposed where CO adsorbed on Ir sites and O₂ adsorbed on FeO_x sites; the reaction may take place at the interface of Ir and FeO_x or via a spill-over process.     

A comparative study of Ag/Al2O3 and Cu/Al2O3 catalysts for the selective catalytic reduction of NO by C3H6

The selective catalytic reduction (SCR) of NO by C₃H₆ in excess oxygen was evaluated and compared over Ag/Al₂O₃ and Cu/Al₂O₃ catalysts. Ag/Al₂O₃ showed a high activity for NO reduction. However, Cu/Al₂O₃ showed a high activity for C₃H₆ oxidation. The partial oxidation of C₃H₆ gave surface enolic species and acetate species on the Ag/Al₂O₃, but only an acetate species was clearly observed on the Cu/Al₂O₃. The enolic species is a more active intermediate towards NO + O₂ to yield—NCO species than the acetate species on the Ag/Al₂O₃ catalyst. The Ag and Cu metal loadings and phase changes on Al₂O₃ support can affect the activity and selectivity of Ag/Al₂O₃ and Cu/Al₂O₃ catalysts, but the formation of enolic species is the main reason why the activity of the Ag/Al₂O₃ catalyst for NO reduction is higher than that of the Cu/Al₂O₃ catalyst.     

Comparison of catalytic activity and selectivity of Pd/(OSC + Al2O3) and (Pd + OSC)/Al2O3 catalysts

The effect of the Pd addition method into the fresh Pd/(OSC + Al₂O₃) and (Pd + OSC)/Al₂O₃ catalysts (OSC material = Ce_xZr_1−xO₂ mixed oxides) was investigated in this study. The CO + NO and CO + NO + O₂ model reactions were studied over fresh and aged catalysts. The differences in the fresh catalysts were insignificant compared to the aged catalysts. During the CO + NO reaction, only small differences were observed in the behaviour of the fresh catalysts. The light-off temperature of CO was about 20 °C lower for the fresh Pd/(OSC + Al₂O₃) catalyst than for the fresh (Pd + OSC)/Al₂O₃ catalyst during the CO + NO + O₂ reaction. For the aged catalysts lower NO reduction and CO oxidation activities were observed, as expected. Pd on OSC-containing alumina was more active than Pd on OSC material after the agings. The activity decline is due to a decrease in the number of active sites on the surface, which was observed as a larger Pd particle size for aged catalysts than for fresh catalysts. In addition, the oxygen storage capacity of the aged Pd/(OSC + Al₂O₃) catalyst was higher than that of the (Pd + OSC)/Al₂O₃ catalyst.     

MnOx/Pt/Al2O3 catalysts for CO oxidation in H2-rich streams

The catalytic activity of Pt on alumina catalysts, with and without MnO_x incorporated to the catalyst formulation, for CO oxidation in H₂-free as well as in H₂-rich stream (PROX) has been studied in the temperature range of 25–250 °C. The effect of catalyst preparation (by successive impregnation or by co-impregnation of Mn and Pt) and Mn content in the catalyst performance has been studied. A low Mn content (2 wt.%) has been found not to improve the catalyst activity compared to the base catalyst. However, catalysts prepared by successive impregnation with 8 and 15 wt.% Mn have shown a lower operation temperature for maximum CO conversion than the base catalyst with an enhanced catalyst activity at low temperatures with respect to Pt/Al₂O₃. A maximum CO conversion of 89.8%, with selectivity of 44.9% and CO yield of 40.3% could be reached over a catalyst with 15 wt.% Mn operating at 139 °C and λ = 2. The effect of the presence of 5 vol.% CO₂ and 5 vol.% H₂O in the feedstream on catalysts performance has also been studied and discussed. The presence of CO₂ in the feedstream enhances the catalytic performance of all the studied catalysts at high temperature, whereas the presence of steam inhibits catalysts with higher MnO_x content.     

Effect of the addition of transition metals to Pt/Ba/Al2O3 catalyst on the NOx storage-reduction catalysis under oxidizing conditions in the presence of SO2

The NO_x storage-reduction catalysis under oxidizing conditions in the presence of SO₂ has been investigated on Pt/Ba/Fe/Al₂O₃, Pt/Ba/Co/Al₂O₃, Pt/Ba/Ni/Al₂O₃, and Pt/Ba/Cu/Al₂O₃ catalysts compared with Pt/Ba/Al₂O₃, Pt/Fe/Al₂O₃, Pt/Co/Al₂O₃, Pt/Ni/Al₂O₃, Pt/Cu/Al₂O₃ and Pt/Al₂O₃ catalysts. The NO_x purification activity of Pt/Ba/Fe/Al₂O₃ catalyst was the highest of all the catalysts investigated in this paper after an aging treatment. That of the aged Pt/Ba/Co/Al₂O₃ and Pt/Ba/Ni/Al₂O₃ catalysts was essentially the same as that of the aged Pt/Ba/Al₂O₃ catalyst, while that of the aged Pt/Ba/Cu/Al₂O₃ and Pt/Cu/Al₂O₃ catalysts was substantially lower than the others.

The Fe-compound on the aged Pt/Ba/Fe/Al₂O₃ catalyst has played a role in decreasing the sulfur content on the catalyst after exposure to simulated reducing gas compared with the Pt/Ba/Al₂O₃ catalyst without the Fe-compound. XRD and EDX show that the Fe-compound inhibits the growth in the size of BaSO₄ particles formed on the Pt/Ba/Fe/Al₂O₃ catalyst under oxidizing conditions in the presence of SO₂ and promotes the decomposition of BaSO₄ and desorption of the sulfur compound under reducing conditions.     

Reactivation of sintered Pt/Al2O3 oxidation catalysts

The reactivation of thermally sintered Pt/Al₂O₃ catalysts used in the simultaneous oxidation of CO and propene has been achieved by an oxychlorination treatment. The catalyst can be considered to model the active component of the catalytic converter fitted to diesel driven cars. Platinum crystallites redispersion was verified by XRD, H₂ chemisorption, TEM and FTIR. The extent of regeneration reflects the platinum particle redispersion achieved by such a treatment. Oxychlorination also introduced electronic effects in the Pt particle caused by the presence of chlorine at the Pt-Al₂O₃ interface but no detrimental result of this was observed in the oxidation reactions. The results indicate that the deactivation of the diesel oxidation catalysts (DOCs) can be reverted by this simple treatment resulting in a remarkable recovery of the catalytic activity.     

低负载Pd/Al2O3催化剂的制备及其对CO室温催化性能研究

采用等体积浸渍法和还原法结合制备了Pd/Al_2O_3催化剂,通过N_2吸附-脱附、SEM、TEM、X射线衍射、X射线光电子能谱和CO原位漫反射傅里叶变换红外光谱等表征手段对制备的样品微观结构进行了系统分析,考察了不同Pd负载量和测试条件下CO催化氧化性能。实验结果表明,水合肼还原法实现了Pd在Al_2O_3载体上的均匀分散,Pd颗粒的直径在9 nm左右,且为Pd单质;负载后的催化剂呈现明显的中孔结构特征,有利于气体分子的扩散。在0.2%～0.5%的低负载质量分数下,CO的催化性能随着Pd负载量的增加而增加,随着CO进口浓度和空速的升高而逐渐降低,在进口浓度为0.05%,空速为4 017 h~(-1)时,不同负载量的催化剂均能使CO完全催化;温度对催化剂的催化效果影响显著,从常温到50℃催化剂的性能变化显著;湿度增加对催化有一定的促进作用。Pd负载质量分数0.5%的催化剂稳定性测试表明,催化剂能够在100 h内保持92%以上的稳定转化率。     

Pd–Pt/Al2O3 bimetallic catalysts for the advanced oxidation of reactive dye solutions

The Pd–Pt/Al₂O₃ bimetallic catalysts showed high activities toward the wet oxidation of the reactive dyes in the presence of 1% H₂ together with excess oxygen. Palladium was believed to act as a co-catalyst to spillover the adsorbed H₂ onto the surface of the oxidized Pt surface, and thereby the reducibility of the Pt increased greatly. The organic dye molecule adsorbed on the reduced Pt surface more easily than the oxidized Pt surface under the competition with excess oxygen, which is an essential step for the catalytic wet oxidation (CWO). The Pd–Pt/Al₂O₃ catalysts also produced H₂O₂ from H₂/O₂ mixture, and the hydroxyl radical was formed through the subsequent decomposition of H₂O₂. Additional oxidation of the reactive dyes was obtained with hydroxyl radical. The high activities of the Pd–Pt/Al₂O₃ catalysts were believed to be due to the combined effects of the faster redox cycle resulting from the increased reducibility of Pt surface and the additional oxidation of the reactive dyes with hydroxyl radical.     

On the activation of Pt/Al2O3 catalysts in HC-SCR by sintering: determination of redox-active sites using Multitrack

A highly dispersed Pt/Al₂O₃ catalyst was used for the selective catalytic reduction of NO_x using propene (HC-SCR). Contact with the reaction gas mixture led to a significant activation of the catalyst at temperatures above 523 K. According to CO chemisorption data and HRTEM analysis, Pt particles on the activated catalyst had sintered. The redox behavior of the fresh and sintered catalysts was investigated using Multitrack, a TAP-like pulse reactor. If Pt particles on the catalyst are highly dispersed (average size below 2 nm), only a small part (10%) of the total number of Pt surface sites as determined by CO chemisorption (Pt_surf) participates in H₂/O₂ redox cycles (Pt_surf,redox) in Multitrack conditions. For a sintered catalyst, with an average particle size of 2.7 nm, the number of Pt_surf and Pt_surf,redox sites are in good agreement. Similar results were obtained for both catalysts using NO as the oxidant. The low number of Pt_surf,redox sites on highly dispersed Pt/Al₂O₃ is explained by the presence of a kinetically more stable—probably ionic—form of Pt---O bonds on all surface sites of the smaller Pt particles, including corner, edge and terrace sites. When the average particle size shifts to 2.7 nm, the kinetic stability of all Pt---O bonds is collectively decreased, enabling the participation of all Pt surface sites in the redox cycles.

A linear correlation between the NO_x conversion in HC-SCR, and the amount of Pt_surf,redox was found. This suggests that redox-active Pt sites are necessary for catalytic activity. In addition, the correlation could be significantly improved by assuming that Pt_surf,terrace sites of the particles larger than 2.7 nm are mainly responsible for HC-SCR activity in steady state conditions. Implications of these results for the pathway of HC-SCR over Pt catalysts are discussed.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

TAP study of NOx storage and reduction on Pt/Al2O3 and Pt/Ba/Al2O3

A systematic mechanistic study of NO storage and reduction over Pt/Al₂O₃ and Pt/BaO/Al₂O₃ is carried out using Temporal Analysis of Products (TAP). NO pulse and NO/H₂ pump-probe experiments at 350 °C on pre-reduced, pre-oxidized, and pre-nitrated catalysts reveal the complex interplay between storage and reduction chemistries and the importance of the Pt/Ba coupling. NO pulsing experiments on both catalysts show that NO decomposes to major product N₂ on clean Pt but the rate declines as oxygen accumulates on the Pt. The storage of NO over Pt/BaO/Al₂O₃ is an order of magnitude higher than on Pt/Al₂O₃ showing participation of Ba in the storage even in the absence of gas phase O₂. Either oxygen spillover or transient NO oxidation to NO₂ is postulated as the first steps for NO storage on Pt/BaO/Al₂O₃. The storage on Pt/Ba/Al₂O₃ commences as soon as Pt–O species are formed. Post-storage H₂ reduction provides evidence that a fraction of NO is not stored in close proximity to Pt and is more difficult to reduce. A closely coupled Pt/Ba interfacial process is corroborated by NO/H₂ pump-probe experiments. NO conversion to N₂ by decomposition is sustained on clean Pt using excess H₂ pump-probe feeds. With excess NO pump-probe feeds NO is converted to N₂ and N₂O via the sequence of barium nitrate and NO decomposition. Pump-probe experiments with pre-oxidized or pre-nitrated catalyst show that N₂ production occurs by the decomposition of NO supplied in a NO pulse or from the decomposition of NOx stored on the Ba. The transient evolution of the two pathways depends on the extent of pre-nitration and the NO/H₂ feed ratio.     

Pd-Pt-Ce/Al_2O_3催化剂在VOC净化处理中的催化性能

采用浸渍法制备Pd-Pt-Ce/Al_2O_3催化剂,考察贵金属Pd和Pt负载量、助剂种类及负载量、空速对催化甲苯燃烧活性的影响。结果表明,适宜的贵金属负载量和助剂可极大提高Pd-Pt/Al_2O_3催化剂活性,当Pd和Pt质量分数分别为0.05%和0.005%、助剂Ce质量分数为1%时,Pd-Pt-Ce/Al_2O_3催化剂在低温条件下表现出较好的催化性能。空速对催化剂的催化活性影响较为明显,适宜的空速低于20 000 h-1。     

Transient studies of carbon dioxide reforming of methane over Pt/ZrO2 and Pt/Al2O3

The mechanism of the CO₂ reforming of methane reaction over the Pt/ZrO₂ catalyst was investigated using a temporal analysis of products (TAP) reactor system. For comparative purposes, the reaction pathway using a Pt/Al₂O₃ catalyst was also examined. A reaction sequence is suggested for both catalysts. Over both catalysts, methane decomposition takes place over platinum. The main difference between the two catalysts concerns the carbon dioxide dissociation. Over Pt/Al₂O₃ this step is assisted by hydrogen. Over Pt/ZrO₂ this step takes place over the zirconia support and involves surface vacancies. Moreover, large pools of formate and carbonate species are present on the zirconia. Transient studies conducted to determine the origin of carbon species accumulated during CO₂ reforming revealed that more than 99% of the carbon was derived from the methane molecule over both catalysts. Over the Pt/ZrO₂ catalyst, only a single very reactive carbon species was detected, while over the Pt/Al₂O₃ a second less active species was also formed.     

Total oxidation of propene and propane over gold–copper oxide on alumina catalysts: Comparison with Pt/Al2O3

Oxidation of propene and propane to CO₂ and H₂O has been studied over Au/Al₂O₃ and two different Au/CuO/Al₂O₃ (4 wt.% Au and 7.4 wt.% Au) catalysts and compared with the catalytic behaviour of Au/Co₃O₄/Al₂O₃ (4.1 wt.% Au) and Pt/Al₂O₃ (4.8 wt.% Pt) catalysts. The various characterization techniques employed (XRD, HRTEM, TPR and DR-UV–vis) revealed the presence of metallic gold, along with a highly dispersed CuO (6 wt.% CuO), or more crystalline CuO phase (12 wt.% CuO).

A higher CuO loading does not significantly influence the catalytic performance of the catalyst in propene oxidation, the gold loading appears to be more important. Moreover, it was found that 7.4Au/CuO/Al₂O₃ is almost as active as Pt/Al₂O₃, whereas Au/Co₃O₄/Al₂O₃ performs less than any of the CuO-containing gold-based catalysts.

The light-off temperature for C₃H₈ oxidation is significantly higher than for C₃H₆. For this reaction the particle size effect appears to prevail over the effect of gold loading. The most active catalysts are 4Au/CuO/Al₂O₃ (gold particles less than 3 nm) and 4Au/Co₃O₄/Al₂O₃ (gold particles less than 5 nm).     

CO oxidation over promoted Pt catalysts

A study of CO oxidation by O₂ over Pt catalysts, promoted by MnO_x and CoO_x, is described. The activities of Pt/SiO₂, Pt/MnO_x/SiO₂ and Pt/CoO_x/SiO₂ are compared with commercial Pt/Al₂O₃, Pt/Rh/Al₂O₃ and Pt/CeO_x/Al₂O₃ catalysts. Since these catalysts differ in dispersion and weight loading of platinum, the turnover frequencies are also compared. The following order in activity in CO oxidation after a reductive pretreatment is found: Pt/CoO_x/SiO₂ > Pt/MnO_x/SiO₂, Pt/CeO_x/Al₂O₃ > Pt/Al₂O₃, Pt/Rh/Al₂O₃, Pt/SiO₂. Over Pt/CoO_x/SiO₂ CO is already oxidised at room temperature. Possible models to account for the high activity of Pt/CoO_x/SiO₂ in the CO/O₂ reaction are presented and discussed. Partially reduced metal oxides are necessary to increase the activity of the Pt/CoO_x/SiO₂, Pt/MnO_x/SiO₂ or Pt/CeO_x/Al₂O₃ catalysts. It was shown that mild ageing treatments did not affect the activity of the Pt/CoO_x/SiO₂ catalyst in CO oxidation.     

Effects of ZrO2/Al2O3 properties on the catalytic activity of Pd catalysts for methane combustion and CO oxidation

Zirconia supported on alumina was prepared and characterized by BET surface area, X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), temperature programmed desorption (TPD), and pulse reaction. 0.2% Pd/ZrO₂/Al₂O₃ catalyst were prepared by incipient wetness impregnation of supports with aqueous solution of Pd(NO₃)₂. The effects of support properties on catalytic activity for methane combustion and CO oxidation were investigated. The results show that ZrO₂ is highly dispersed on the surface of Al₂O₃ up to 10 wt.% ZrO₂, beyond this value tetragonal ZrO₂ is formed. The presence of a small amount of ZrO₂ can increase the surface area, pore volume and acidity of support. CO–TPD results show that the increase of CO adsorption capacity and the activation of CO bond after the presence of ZrO₂ lead to the increase of catalytic activity of Pd catalyst for CO oxidation. CO pulse reaction results indicate that the lattice oxygen of support can be activated at lower temperature following the presence of ZrO₂, but it does not accelerate the activity of 0.2% Pd/ZrO₂/Al₂O₃ for methane combustion. 0.2% Pd/ZrO₂/Al₂O₃ dried at 120 °C shows highest activity for CH₄ combustion, and the activity can be further enhanced following the repeat run. The increase of treatment temperature and pre-reduction can decrease the activity of catalyst for CH₄ combustion.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.