海底冷泉区沉积物-水界面甲烷通量原位观测研究进展

海底沉积物-水界面作为冷泉跨圈层活动最关键的界面，近年来已成为冷泉区碳循环研究调查的重点目标。为准确获取海洋沉积物-水界面的流体通量，客观重建界面环境过程，评估环境效应，必须发展一整套精确、高效、科学的水下原位甲烷通量测量技术。综述了当前海洋冷泉区沉积物-水界面甲烷通量研究的意义与价值，详细介绍了多种较为成熟的海洋沉积物-水界面甲烷原位通量测试技术工作原理、使用方法和优缺点等，如测试游离气泡态甲烷通量的渗漏帐篷、声学反射、时序影像等技术方法，原位溶解态甲烷膜脱气技术的甲烷传感器、激光拉曼光谱测量方法等，同时对全球该领域已经调查的地区、研究现状和进展进行了详细的介绍。最后从技术层面对这一研究领域未来的发展方向和趋势进行展望，以期为未来国内海洋冷泉区沉积物-水界面甲烷通量原位观测研究提供思路与方向借鉴。     

海底冷泉原位观测装置研究回顾与展望

海底冷泉多由海底天然气渗漏形成,是以水、碳氢化合物、硫化氢或二氧化碳为主要成分的流体.它既是海底天然气水合物存在的标志,又与温室效应、海洋生态环境、冷泉生物群落等问题密切相关,对海底冷泉的流体渗漏通量和化学组成进行测定,对认识上述问题有重大意义.与实验室化学分析和数值模拟相比,原位观测可保证数据的可靠性和真实性,作为冷...     

夏季东、黄海沉积物中甲烷的分布和沉积物-水界面通量

沉积物释放是海洋环境中甲烷(CH_4)的重要来源。通过2013年7月和8月两个航次,对东、黄海泥质区沉积物中CH_4浓度的垂直分布和沉积物-水界面通量进行了研究。结果表明,除个别站位外,黄海沉积物(50 cm以浅)中CH_4的浓度变化范围在0.2～1.0μmol/L之间,长江口及浙闽沿岸附近的沉积物中CH_4浓度则要更高(1.0～2.0μmol/L),而东海东部海域沉积物中CH_4浓度波动范围为0.2～3.0μmol/L。总体来说,东、黄海沉积物中CH_4浓度偏低,这可能与观测到的高浓度硫酸盐(20 mmol/L)有关。通过整柱密室培养实验估算出东、黄海沉积物-水界面CH_4释放速率在0.64～2.12μmol/(m2·d)之间,东、黄海沉积物CH_4释放总量为6.7×108 mol/yr;但采用菲克定律估算的CH_4扩散通量则要比现场培养的结果低2～5倍,表明不同的方法在估算沉积物-水界面CH_4通量上还具有一定的不确定性。     

基于单波束测深资料的海底冷泉动力学特征反演方法研究

为了准确理解冷泉水体中甲烷气体的分布规律,综合运用单波束测深数据和冷泉水体流场数据,建立了冷泉气泡上升、溶解速率的定量反演方法,利用现场海试资料对反演方法进行了验证,并对海试区域的冷泉气体溢出、溶解通量以及冷泉水体的甲烷浓度进行了估算。计算结果表明,考察船航向与冷泉水体流向的差异会对声学探测结果产生影响,当航向与流向的夹角大于±60°时,声学成像中冷泉倾角的误差将超过50%。同时,冷泉气泡上升速率的衰减与溢出口水深显著相关,相关系数可达0.9,并且冷泉上升流对上升速率的提升效果明显。水合物稳定带的分布对冷泉气泡的收缩速率影响显著,稳定带内、外收缩速率的差异可达3～4倍。冷泉气体通量的计算结果表明,调查区域内冷泉的溢出强度整体较大,同时溶解通量与水深之间呈现明显的分段效应。根据冷泉气体溶解通量估算的冷泉水体甲烷浓度与色谱分析结果具有较好的一致性。相关研究有助于实现对冷泉水体中甲烷气体分布的定量评估,为潜在海底冷泉区的圈划和海域天然气水合物的调查提供技术支撑。     

海底甲烷缺氧氧化与冷泉碳酸盐岩沉淀动力学研究进展

海底缺氧带甲烷氧化作用是一个重要的甲烷生物地球化学过程,已被许多地球化学现象所证实。甲烷缺氧氧化有效地减少了渗漏到海水和大气中的甲烷通量,但目前仅有的数据还不能很好地限定甲烷缺氧氧化在全球甲烷循环和全球碳循环中的作用。甲烷缺氧氧化的机理还存在争议,很可能是一个“反甲烷生成”过程。在许多天然气渗漏发育区域,由于甲烷缺氧氧化作用引起环境碱度的增加而沉淀冷泉碳酸盐岩,在海底表层沉积物中形成块状碳酸盐岩结壳。但冷泉碳酸盐岩生成所需的物理化学和生物地球化学条件在很大程度上还不清楚。数值计算表明,孔隙水中溶解足够量的甲烷、冷泉渗漏强度适中、较小的生物扰动作用有利于冷泉碳酸盐岩的生成,而过高的沉积速率则抑制冷泉碳酸盐岩结壳的生成。因此,海底发育冷泉碳酸盐岩可以指示天然气渗漏系统的演化特征。     

海底天然气水合物及冷泉流体渗漏的原位观测技术

海底天然气水合物藏是天然的巨型碳储藏库,是深部甲烷等烃类气体运移至海底过程中暂时的碳储,是地球碳循环过程的重要一环。冷泉通常与海底天然气水合物藏分解密切相关,是深源或浅层气及水合物分解气在海底发生渗漏的现象。该文根据国内外天然气水合物及冷泉系统勘查的最新动向,综述了与水合物及冷泉流体渗漏相关的羽状流、运移通道、海底微地形地貌等要素的海底原位观测技术,主要包括：走航式及坐底式原位观测、海面及低空渗漏甲烷观测、海底可视化观测、与水合物及冷泉相关的海底观测网络等。综合使用原位观测技术可以更细致、全面地描绘水合物和冷泉系统的时空“景象”,更好地协助厘清海底渗漏甲烷的归趋,拓展人类对深海独特生命绿洲的认知。     

自主式深海海底溶质通量原位观测站研究进展

针对深入了解深海海底界面的物理、化学和生物动态变化过程及机制的观测需求,综述了自主式海底观测站(着陆器,lander)在深海海底溶质通量监测的研究进展。探讨了海底观测站的设计与实施技术,分析总结了深海自主式原位观测站在沉积物-水界面化学组分通量的观测机理,讨论了自主式海底观测站的国内外发展现状。自主式海底观测站具有可灵活机动选择观测地点、操作简单、便于多参数综合测量的特点,为获取深海海底长时空尺度综合参数资料提供了有效的技术支撑。根据目前深海生物地球化学循环研究特点,提出了自主式海底观测站面临的问题与发展建议。     

硫酸盐-甲烷界面与甲烷通量及下伏水合物赋存的关系

硫酸盐-甲烷界面在富甲烷和含天然气水合物的海洋沉积区已经成为一个重要的生物地球化学识别边界.在硫酸盐-甲烷界面之上,沉积物中的硫酸盐因参与分解有机质和甲烷厌氧氧化反应而被消耗,而界面之下沉积物中的甲烷则不断生成,含量逐渐增加.根据该界面附近硫酸盐浓度和甲烷浓度的变化特征,可以判断该区甲烷流体通量的大小,从而指示下伏天然气水合物的可能赋存状况.南海北部陆坡的柱状沉积物孔隙水数据的分析显示,其硫酸盐-甲烷界面埋深比较浅,表明该海域的甲烷通量较高.这种高甲烷通量很可能是由下伏的天然气水合物所引起的,并暗示着该区下伏海底可能有天然气水合物沉积层赋存.     

硫酸盐-甲烷界面与甲烷通量及下伏天然气水合物赋存的关系

硫酸盐-甲烷界面在富甲烷和含天然气水合物的海洋沉积区已经成为一个重要的生物地球化学识别边界。在硫酸盐-甲烷界面之上,沉积物中的硫酸盐因参与分解有机质和甲烷厌氧氧化反应而被消耗,而其界面之下沉积物中的甲烷则不断生成,含量逐渐增加。根据该界面附近硫酸盐浓度和甲烷浓度的变化特征,可以判断该区甲烷流体通量的大小,从而指示下伏天然气水合物的可能赋存状况。南海北部陆坡的柱状沉积物孔隙水数据的分析显示,硫酸盐-甲烷界面埋深比较浅,表明该海域的甲烷通量较高。这种高甲烷通量很可能是由下伏的天然气水合物所引起的,并暗示着该区下伏海底可能有天然气水合物沉积层赋存。     

用于沉积物-海水界面污染通量监测的自动采样技术

研究海底沉积物一海水界面污染物迁移规律的最佳方法是通过原位无扰动采样技术获取该界面水样,经过实验室分析计算得出污染通量.文中介绍了用于沉积物-海水界面污染通量监测的自动采样技术,通过测量通量舱在海底沉积物上隔离海水中的污染物含量的变化,能实现痕量重金属等污染通量的实时、现场、自动采样和监测.     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,