Synthesis and properties of methyl hexahydrophthalic anhydride‐cured fluorinated epoxy resin 2,2‐bisphenol hexafluoropropane diglycidyl ether

The fluorinated epoxy resin, 2,2‐bisphenol hexafluoropropane diglycidyl ether (DGEBHF) was synthesized through a two‐step procedure, and the chemical structure was confirmed by ¹H n uclear magnetic resonance (NMR), ¹³C NMR, and Fourier transform infrared (FTIR) spectra. Moreover, DGEBHF was thermally cured with methyl hexahydrophthalic anhydride (MHHPA). The results clearly indicated that the cured DGEBHF/MHHPA exhibited higher glass transition temperature (T_g 147°C) and thermal decomposition temperature at 5% weight loss (T₅ 372°C) than those (T_g 131.2°C; T₅ 362°C) of diglycidyl ether of bisphenol A (DGEBA)/MHHPA. In addition, the incorporation of bis‐trifluoromethyl groups led to enhanced dielectric properties with lower dielectric constant (D_k 2.93) of DGEBHF/MHHPA compared with cured DGEBA resins (D_k 3.25). The cured fluorinated epoxy resin also gave lower water absorption measured in two methods relative to its nonfluorinated counterparts. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2801–2808, 2013     

Preparation and properties of bio‐based epoxy montomorillonite nanocomposites derived from polyglycerol polyglycidyl ether and ε‐polylysine

Glycerol polyglycidyl ether (GPE) and polyglycerol polyglycidyl ether (PGPE) were cured with ε‐poly(L ‐lysine) (PL) using epoxy/amine ratios of 1 : 1 and 2 : 1 to create bio‐based epoxy cross‐linked resins. When PGPE was used as an epoxy resin and the epoxy/amine ratio was 1 : 1, the cured neat resin showed the greatest glass transition temperature (T_g), as measured by differential scanning calorimetry. Next, the mixture of PGPE, PL, and montomorillonite (MMT) at an epoxy/amine ratio of 1 : 1 in water was dried and cured finally at 110°C to create PGPE‐PL/MMT composites. The X‐ray diffraction and transmission electron microscopy measurements revealed that the composites with MMT content 7–15 wt % were exfoliated nanocomposites and the composite with MMT content 20 wt % was an intercalated nanocomposite. The T_g and storage modulus at 50–100°C for the PGPE‐PL/MMT composites measured by DMA increased with increasing MMT content until 15 wt % and decreased at 20 wt %. The tensile strength and modulus of the PGPE‐PL/MMT composites (MMT content 15 wt %: 42 and 5300 MPa) were much greater than those of the cured PGPE‐PL resin (4 and 6 MPa). Aerobic biodegradability of the PGPE‐PL in an aqueous medium was ～ 4% after 90 days, and the PGPE‐PL/MMT nanocomposites with MMT content 7–15 wt % showed lower biodegradability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Study of the epoxy system BADGE (n = 0)/1,2‐DCH/CaCO3 filler by DMA and DSC

The influence of an inorganic filler, CaCO₃, on the curing kinetics of an epoxy system composed of diglycidyl ether of bisphenol A [BADGE (n = 0)], 1,2‐diaminecyclohexane (1,2‐DCH), and CaCO₃ filler was studied by DMA and DSC. Different contents of filler in the range from 10 to 30%, referred to the total weight of the mixture, were tried. It was found that maximum reproducibility of the results and better performance correspond to a filler content of 20%. As usual, the T_g's obtained by DMA and DSC are different at 10–20°C. The results obtained from this study were compared with those corresponding to the system BADGE (n = 0)/1,2‐DCH without filler; the T_g for this last system is higher than that for the system with filler incorporated, whereas E′ and M_c (molecular weight between repetition units) are lower for the system without filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 366–370, 2002     

Epoxide‐terminated hyperbranched polyether sulphone as triple enhancement modifier for DGEBA

Epoxide‐terminated hyperbranched polyether sulphones (EHBPESs) with different backbone structures were synthesized and used as tougheners for diglycidyl ether of bisphenol‐A (DGEBA) curing system, which result in nonphase‐separated cured networks. Effects of backbone structure (at comparable degree of polymerization) and loading contents on the mechanical and thermal properties of cured hybrids were investigated. The hybrid containing EHBPES3, which has the most flexible backbone, shows the best mechanical performance and highest glass transition temperature (T_g). Compared with unmodified system, the impact strength, tensile strength, elongation at break of the hybrid containing 5% EHBPES3 increased by 69.8%, 9.4%, and 60.2%, respectively. The balanced improvements were attributed to the increased crosslink density and fractional free volume as well as the unique inhomogeneous network structure because of incorporation of hyperbranched modifiers with proper structure and loading contents. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41910.     

Dynamic mechanical and shape memory properties of copolymers based on o‐allylphenol type benzoxazines and diglycidyl ether of bisphenol‐A

Three benzoxazines based on o‐allylphenol and 1,6‐hexamethylenediamine (HDA) or 4,4′‐diaminodiphenyl methane (DDM) or 4,4′‐diaminodiphenyl ether (DDE) were respectively blended with diglycidyl ether of bisphenol‐A (DGEBA) in various weight ratios followed by thermal polymerization to prepare three series of benzoxazine/DGEBA copolymers. With increasing DGEBA content, the peak temperature of the exothermic peaks in the DSC curves shows a systematic increase for the three series of benzoxazine/DGEBA blends. Each copolymer shows a single glass transition temperature (T_g). As the content of DGEBA is increased, T_g reaches a minimum for the copolymer system based on HDA but a maximum for the two systems based on DDM and DDE. For the same benzoxazine/DGEBA weight ratio, copolymers based on DDM and DDE show high T_g values over those based on HDA. The three series of benzoxazine/DGEBA copolymers exhibit a one‐way dual shape memory effect based on T_g, and the shape memory properties of the copolymers under tensile deformation mode vary with the variation of both diamine bridge structure and DGEBA content. © 2018 Society of Chemical Industry     

Thermophysical properties of anhydride‐cured epoxy/nano‐clay composites

Polymer nano‐composites made with a matrix of anhydride‐cured diglycidyl ether of bisphenol A (DGEBA) and reinforced with organo‐montmorillonite clay were investigated. A sonication technique was used to process the epoxy/clay nano‐composites. The thermal properties of the nano‐composites were measured with dynamic mechanical analysis (DMA). The glass transition temperature T_g of the anhydride‐cured epoxy was higher than the room temperature (RT). For samples with 6.25 wt% (4.0 vol%) of clay, the storage modulus at 30°C and at (T_g + 15)°C was observed to increase 43% and 230%, respectively, relative to the value of unfilled epoxy. The clay reinforcing effect was evaluated using the Tandon‐Weng model for randomly oriented particulate filled composites. Transmission electron microscopy (TEM) examination of the nano‐composites prepared by sonication of clays in acetone showed well‐dispersed platelets in the nano‐composites. The clay nano‐platelets were observed to be well‐intercalated/expanded in the anhydride‐cured epoxy resin system. POLYM. COMPOS., 26:42–51, 2005. © 2004 Society of Plastics Engineers.     

Preparation of 4‐(4‐hydroxyphenoxy)phenol diglycidyl ether with improved toughness behavior

A high‐performance difunctional epoxy resin, 4‐(4‐hydroxyphenoxy)phenol diglycidyl ether (DHPOP), was synthesized by a two‐step method. The curing behavior of DHPOP was investigated by nonisothermal differential scanning calorimetry method and the curing kinetics results revealed that the introduction of ether linkage could improve the activity of epoxy groups, leading to a lower curing temperature and apparent activation energy compared with that of the commercial bisphenol‐A diglycidyl ether (DGEBA). A series of copolymers were then prepared by varying the mass ratio of DHPOP and DGEBA, which were cured with 4,4′‐diaminodiphenyl methane. The effect of DHPOP contents on thermal and mechanical properties and fracture morphology was studied. As expected, with the increase of DHPOP in the network, the impact strength and char yield were significantly enhanced, while the glass transition temperature (T_g) remained unchanged because of the increase of crosslink density. The excellent toughness endows the DHPOP with the promising potential for the application as high‐performance resin matrix. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46458.     

Blends of epoxy resin with amine‐terminated polyoxypropylene elastomer: Morphology and properties

A liquid diglycidyl ether of bisphenol A (DGEBA) epoxy resin is blended in various proportions with amine‐terminated polyoxypropylene (POPTA) and cured using an aliphatic diamine hardener. The degree of crosslinking is varied by altering the ratio of diamine to epoxy molecules in the blend. The mixture undergoes almost complete phase separation during cure, forming spherical elastomer particles at POPTA concentrations up to 20 wt %, and a more co‐continuous morphology at 25 wt %. In particulate blends, the highest toughness is achieved with nonstoichiometric amine‐to‐epoxy ratios, which produce low degrees of crosslinking in the resin phase. In these blends, the correlation between G_IC and plateau modulus (above the resin T_g), over a wide range of amine‐to‐epoxy ratios, confirms the importance of resin ductility in determining the fracture resistance of rubber‐modified thermosets. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 427–434, 1999     

Studies on syntheses and properties of episulfide‐type optical resins with high refractive index

A series of novel high refractive index episulfide‐type optical resins were prepared by ring‐opening copolymerization of bis(β‐epithiopropylthioethyl) sulfide (BEPTES) with episulfide derivative of diglydicyl ether of bisphenol A (ESDGEBA) and 2,4‐tolylene diisocyanate (TDI), respectively, in the presence of triethylamine as a curing catalyst. The episulfide monomers, BEPTES and ESDGEBA, were synthesized from their corresponding epoxy compounds, respectively. The cured transparent resins exhibit high refractive index (n_d > 1.63) and relatively low dispersion. The refractive index (n_d) and Abbe's number (ν_d) of the BEPTES/ESDGEBA curing system increased linearly with the weight content of BEPTES monomer in the range from 1.633 and 34.0 for the copolymer with 10 wt % of BEPTES to 1.697 and 38.1 for the homopolymer of pure BEPTES. For the BEPTES/TDI curing system, the refractive index and Abbe's number varied linearly with the molar ratio of BEPTES to TDI from 1.652 and 28.7 to 1.669 and 34.6. High glass‐transition temperatures (T_g > 130°C) of the cured BEPTES/TDI resins were observed, which indicate that the cured BEPTES/TDI resins possess a good heat resistance. The optical, physical, and thermal properties of the episulfide‐type cured optical resins were also discussed in this study. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2426–2430, 2003     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry     

Preparation and properties of TiO2‐filled poly(acrylonitrile‐butadiene‐styrene)/epoxy hybrid composites

Poly (acrylonitrile‐butadiene‐styrene) (ABS) was used to modify diglycidyl ether of bisphenol‐A type of epoxy resin, and the modified epoxy resin was used as the matrix for making TiO₂ reinforced nanocomposites and were cured with diaminodiphenyl sulfone for superior mechanical and thermal properties. The hybrid nanocomposites were characterized by using thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), universal testing machine (UTM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The bulk morphology was carefully analyzed by SEM and TEM and was supported by other techniques. DMA studies revealed that the DDS‐cured epoxy/ABS/TiO₂ hybrid composites systems have two T_gs corresponding to epoxy and ABS rich phases and have better load bearing capacity with the addition of TiO₂ particles. The addition of TiO₂ induces a significant increase in tensile properties, impact strength, and fracture toughness with respect to neat blend matrix. Tensile toughness reveals a twofold increase with the addition of 0.7 wt % TiO₂ filler in the blend matrix with respect to neat blend. SEM micrographs of fractured surfaces establish a synergetic effect of both ABS and TiO₂ components in the epoxy matrix. The phenomenon such us cavitation, crack path deflection, crack pinning, ductile tearing of the thermoplastic, and local plastic deformation of the matrix with some minor agglomerates of TiO₂ are observed. However, between these agglomerates, the particles are separated well and are distributed homogeneously within the polymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Influence of cyanate content on the morphology and properties of epoxy resins with phenolphthalein poly(ether ketone)

Phenolphthalein poly(ether ketone) (PEK‐C) was blended with the diglycidyl ether of bisphenol A epoxy resin and bisphenol A dicyanate ester. The effect of cyanate content on cure behaviors, thermal and mechanical properties of PEK‐C/epoxy/cyanate mixtures was investigated. As results, the increase of cyanate content slightly hindered the cure reaction of the mixtures. Fourier transform infrared results indicated that the curing reaction of the cured mixtures was complete. When the cyanate ester content increased, the flexural properties and T_g values were enhanced, and the initial thermal decomposition temperature was reduced. A significant improvement in fracture toughness was obtained when the cyanate group in the mixtures was excessive. The fracture toughness can be well explained by SEM observations. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of curing program on mechanical behavior and water absorption of DGEBA/TETa epoxy network

Water uptake in organic coatings remains an interesting challenge for fundamental and applied researches because chemical, physical, and mechanical properties are concerned. The polymer network, which is affected by the curing program, is a key factor for water absorption. In this work, an epoxy network based on diglycidyl ether of bisphenol A and a hardener triethylentetramine was cured at different temperatures: below T_g (protocol 1) and above T_g (protocol 2). DMA, Differential Scanning Calorimetry (DSC), and FT‐IR measurements showed that both protocols allow to obtain totally cured networks. However, DSC and DMA results revealed that both cured networks present different levels of homogeneity, depending on the different curing conditions, which affect the free volume and the activation volume associated with visco‐elastic properties. The mechanical properties of free films and water sorption behaviors were investigated as function of cured conditions. It was found that protocol 1‐cured networks present higher mechanical properties and was less affected by water ingress than protocol 2‐cured systems, leading to better barrier properties. These results highlight the influence of the curing program onto the heterogeneous distribution of the epoxy network. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of a novel phosphorus‐containing dicyclopentadiene novolac hardener and its cured epoxy resin with improved thermal stability and flame retardancy

A novel phosphorus‐containing dicyclopentadiene novolac (DCPD‐DOPO) curing agent for epoxy resins, was prepared from 9,10‐dihydro‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) and n‐butylated dicyclopentadiene phenolic resin (DCPD‐E). The chemical structure of the obtained DCPD‐DOPO was characterized with FTIR, ¹H NMR and ³¹P NMR, and its molecular weight was determined by gel permeation chromatography. The flame retardancy and thermal properties of diglycidyl ether bisphenol A (DGEBA) epoxy resin cured with DCPD‐DOPO or the mixture of DCPD‐DOPO and bisphenol A‐formaldehyde Novolac resin 720 (NPEH720) were studied by limiting oxygen index (LOI), UL 94 vertical test and cone calorimeter (CCT), and differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), respectively. It is found that the DCPD‐DOPO cured epoxy resin possess a LOI value of 31.6% and achieves the UL 94 V‐0 rating, while its glass transition temperature (T_g) is a bit lower (133 °C). The T_g of epoxy resin cured by the mixture of DCPD‐DOPO and NPEH720 increases to 137 °C or above, and the UL 94 V‐0 rating can still be maintained although the LOI decreases slightly. The CCT test results demonstrated that the peak heat release rate and total heat release of the epoxy resin cured by the mixture of DCPD‐DOPO and NPEH720 decrease significantly compared with the values of the epoxy resin cured by NPEH720. Moreover, the curing reaction kinetics of the epoxy resin cured by DCPD‐DOPO, NPEH720 or their mixture was studied by DSC. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44599.     

Epoxy resin containing the poly(sily ether): Preparation,morphology, and mechanical properties

The poly(sily ether) with pendant chloromethyl groups (PSE) was synthesized by the polyaddition of dichloromethylsilane (DCM) and diglycidylether of bisphenol A (DGEBA) with tetrabutylammonium chloride (TBAC) as a catalyst. This polymer was miscible with diglycidyl ether of bisphenol A (DGEBA), the precursor of epoxy resin. The miscibility is considered to be due mainly to entropy contribution because the molecular weight of DGEBA is quite low. The blends of epoxy resin with PSE were prepared through in situ curing reaction of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐diaminodiphenylmethane (DDM) in the presence of PSE. The DDM‐cured epoxy resin/PSE blends with PSE content up to 40 wt % were obtained. The reaction started from the initial homogeneous ternary mixture of DGEBA/DDM/PSE. With curing proceeding, phase separation induced by polymerization occurred. PSE was immiscible with the 4,4′‐diaminodiphenylmethane‐cured epoxy resin (ER) because the blends exhibited two separate glass transition temperatures (T_gs) as revealed by the means of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). SEM showed that all the ER/PSE blends are heterogeneous. Depending on blend composition, the blends can display PSE‐ or epoxy‐dispersed morphologies, respectively. The mechanical test showed that the DDM‐cured ER/PSE blend containing 25 wt % PSE displayed a substantial improvement in Izod impact strength, i.e., epoxy resin was significantly toughened. The improvement in impact toughness corresponded to the formation of PSE‐dispersed phase structure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 505–512, 2003     

Epoxy resin based on 4,4′-dihydroxydiphenysulfone. I. Synthesis and reaction kinetics with 4,4′-diaminodiphenylmethane and 4,4′-diaminodiphenylsulfone

Epoxy resins based on 4,4′-dihydroxydiphenylsulfone (DGEBS) and diglycidyl ether of bisphenol A (DGEBA) were prepared by alkaline condensation of 4,4′-dihydroxydiphenylsulfone (bisphenol S) with epichlorohydrin and by recrystallization of liquid, commercial bisphenol A-type epoxy resin, respectively. Curing kinetics of the two epoxy compounds with 4,4′-diaminodiphenylmethane (DDM) and with 4,4′-diaminodiphenylsulfone (DDS) as well as T_g values of the cured materials were determined by the DSC method. It was found that the ? SO₂? group both in the epoxy resin and in the harener increases T_g values of the cured materials. DGEBS reacts with the used hardeners faster than does DGEBA and the curing reaction of DGEBS begins at lower temperature than does the curing reaction of DGEBA when the same amine is used. © 1994 John Wiley & Sons, Inc.     

Preparation and properties of novel phosphorus‐containing binaphthyl epoxy polymer

Novel phosphorus‐containing binaphthyl epoxy DGEBN (diglycidyl ether of 2,2′‐hydroxy‐1,1′‐binaphthalene) with high thermal performance was obtained from the addition reaction of DGEBN and diethyl phosphite. The modified binaphthyl epoxy was characterized by Fourier transform infrared (FTIR) and nuclear magnetic resonance spectroscopy. The dynamic mechanical property of the cured epoxy polymer was investigated by dynamic mechanical thermal analysis. The result revealed that the cured polymer with lower phosphorus content displayed higher value of the storage modulus when the networks reached rubbery state (above the glass transition temperature T_g). The T_gs decreased slightly with increasing phosphorous content. The thermal degradation was studied with thermogravimetric analysis and the evolved gas was analyzed using thermogravimetric analysis/Fourier transform infrared technique. The influence of phosphorus content and the chemical structure on the degradation behavior was discussed. The P‐modified binaphthyl epoxy polymers exhibited higher thermal stability than the P‐modified diglycidyl ether of bisphenol A polymer. Flammability measurements were performed by the examination of limited oxygen index and UL‐94 test. Compared with unmodified DGEBN, P‐containing epoxy polymers displayed higher limited oxygen index values and exhibited better flame retardance. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Preparation and thermal properties of bismaleimide blends based on hydroxyphenyl maleimide

N‐(4‐hydroxyphenyl)maleimide was melt‐blended with the glycidyl ether of bisphenol‐A and various mole percentages of 4, 4′‐(diaminodiphenylsulfone) bismaleimide. The cure behaviour of the resins was evaluated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The blends showed distinct reductions in the onset of cure (T_o) and peak exothermic (T_exo) temperatures. The blends cured at low temperatures exhibited glass transition temperatures (T_gs) higher than the cure temperatures. The cured blends showed high moduli, glass transition temperatures in excess of 250 °C and good thermal stabilities up to 400 °C. Copyright © 2005 Society of Chemical Industry     

Effects of melt structure on crystallization behavior of isotactic polypropylene nucleated with α/β compounded nucleating agents

In this study, the melt structure of isotactic polypropylene (iPP) nucleated with α/β compounded nucleating agents (α/β‐CNA, composed of the α‐NA of 0.15 wt % Millad 3988 and the β‐NA of 0.05 wt % WBG‐II) was tuned by changing the fusion temperature T_f. In this way, the role of melt structure on the crystallization behavior and polymorphic composition of iPP were investigated by differential scanning calorimetry (DSC), wide‐angle X‐ray scattering (WAXD) and scanning electron microscopy (SEM). The results showed that when T_f = 200°C (iPP was fully molten), the α/β‐CNA cannot encourage β‐phase crystallization since the nucleation efficiency (NE) of the α‐NA 3988 was obviously higher than that of the β‐NA WBG‐II. Surprisingly, when T_f was in 179–167°C, an amount of ordered structures survived in the melt, resulting in significant increase of the proportion of β‐phase (achieving 74.9% at maximum), indicating that the ordered structures of iPP played determining role in β‐phase crystallization of iPP nucleated with the α/β‐CNA. Further investigation on iPP respectively nucleated with individual 3988 and WBG‐II showed that as T_f decreased from 200°C to 167°C, the crystallization peak temperature T_c of iPP/3988 stayed almost constant, while T_c of iPP/WBG‐II increased gradually when T_f < 189°C and became higher than that of iPP/3988 when T_f decreased to 179°C and lower, which can be used to explain the influence of ordered structure and α/β‐CNA on iPP crystallization. Using this method, the selection of α‐NA for α/β‐CNA can be greatly expanded even if the inherent NE of β‐NA is lower than that of the α‐NA. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41355.     

Thermal,mechanical, and dielectric studies on the DGEBA epoxy blends by using liquid oxidized poly(1,2‐butadiene) as a reactive component

Liquid oxidized poly(1,2‐butadiene) (LOPB) with multi epoxy groups is synthesized to modify diglycidyl end‐caped poly(bisphenol A‐co‐epichlorohydrin) (DGEBA) cured by 4,4′‐diaminodiphenyl sulfone (DDS). FTIR spectra shows that DGEBA and LOPB can be effectively cured by DDS, and the epoxide rubber particles are evenly distributed in the composites till their addition up to 20 wt % of DGEBA as seen from the scanning electron microscope (SEM). Their decomposition temperatures (Td) increase with the increase in LOPB addition at around 10 wt % of DGEBA while the Td for the composite containing 20 wt % LOPB of DGEBA is lower than that of the neat epoxy. The addition of LOPB improves their storage moduli and especially these values at temperatures higher above 150 °C; all the composites exhibit higher glass transition temperature (T_g) than that of the neat epoxy, and the maximum T_g reaches up to 255 °C for the composite containing 15 wt % LOPB of DGEBA. The incorporation of LOPB effectively decreases their dielectric constants and the composite with 10 wt % LOPB of DGEBA possesses the lowest one. The synergic improvements in their various properties are attributed to the networks formation via covalent linkage between the two phases in these reactive blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44689.