共查询到20条相似文献,搜索用时 156 毫秒
1.
文中主要讨论了峰值电流控制模式的斜坡补偿的原理和意义,设计了移相全桥零电压开关控制电路中的斜坡补偿电路。 相似文献
2.
3.
半桥三电平变换器拓扑解决了PFC技术带来的功率管应力过高问题,非常适合于大功率高压输出场合,峰值电流模式采用电压外环,电流内环的双环控制,是开关电源闭环系统最实用的控制模式.对移相半桥三电平DC/DC变换器进行了小信号建模分析;建立了峰值电流内环和电压外环的小信号传递函数,在此基础上给出了峰值电流模式的移相半桥三电平变换器闭环系统结构图,推导出相关闭环传递函数;给出了补偿网络参数设计步骤;对建立的双闭环系统模型进行了MATLAB仿真,结果表明经过补偿后的闭环系统具有满意的性能指标. 相似文献
4.
分析研究了低压大电流全桥变换器电路拓扑结构。分别介绍了功率变压器初级移相控制零电压(ZVS)PWM和移相控制零电压零电流(ZVZCS)PWM软开关全桥变换器主电路拓扑结构,以及功率变压器次级适宜采用的不同电路拓扑形式,并对其优缺点进行了对比分析。文中简要说明了在变换器输入级加入功率因数校正环节的必要性。 相似文献
5.
6.
晶闸管交流调功器在温度控制系统中已得到广泛的应用。按其控制方式来分,有移相触发控制和过零触发控制两种。移相触发控制平滑灵活,能适应各种控制要求,但通过晶闸管输给负载的电压(电流)是缺角正弦波,功率因数差且存在高次谐波,对电网和无线电波会产生射频干扰。1984年,我国水电部颁发了“电力系统谐波管理暂行规定”(SD126-84),严格限制大功率移相调压设备的投网容量,并对已投入运行的移相调压设备提出了限期改造的要求。采用过零触发的晶闸管调功器,负载得到的电压(电流)波形总是完 相似文献
7.
采用电流模式移相PWM控制,在较大的负载范围内实现了开关器件的零电压软开关(ZVS).给出了实验结果. 相似文献
8.
移相全桥ZVS ZCS变换器双闭环控制系统设计 总被引:2,自引:0,他引:2
以移相全桥ZVSZCS变换器作为控制对象,分析了平均电流模式的电压电流双闭环控制系统的控制原理,用MATLAB中的可视化工具SISOTOOL设计了电压电流双闭环的PI调节参数,减少了设计的复杂性和重复性。最后通过MATLAB/Simulink仿真软件搭建出电压电流双闭环控制系统的仿真模型,验证了设计结果的正确性。 相似文献
9.
10.
11.
12.
In this work an inverse E power amplifier with finite DC feed in sub-nominal condition is discussed. In the conventional inverse E the DC feed inductor is considered very large which imposes some conditions to the circuit such as constant current drawn from voltage supply and also a large value for inductance is hard to implement on-chip so this work removes the very large condition from DC feed inductance and proposes a finite DC feed for the structure and extracts the circuit parameters and design equations with regards to this matter. Furthermore to achieve a flexible design this work uses the phase shift between input and output voltages to control efficiency, peak switch voltage and peak switch current then the value of circuit elements and the tradeoffs for every choice are discussed in details and a design guideline is presented for achieving different goals in a finite DC feed inverse E PA. Finally the circuit is simulated in the 0.18 µm CMOS technology and the results are being verified. 相似文献
13.
14.
提出了一种主回路采用峰值电流型控制、次回路采用纹波控制的新型单电感多输出降压型开关电源的设计。这种设计,使单电感多输出的控制回路变得简单,同时也使瞬态响应速度变快,交调影响和纹波变小。其开关频率为2 MHz,两路输出分别为1.8 V和1.2 V,两路负载范围为0~200 mA,实现了全负载可以正常工作。在考虑了各种寄生参数的后仿真条件下,一路负载为200 mA,一路负载从50 mA变化到200 mA,瞬态响应速度小于3μs,交调影响小于0.05 mV/mA,纹波小于30 mV,峰值效率可以达到91%。该芯片已经在CHART 0.18-μm CMOS工艺上设计实现,正在流片验证。 相似文献
15.
16.
峰值电流控制中斜坡补偿电路的设计 总被引:1,自引:0,他引:1
针对峰值电流控制中产生次谐波振荡的问题,阐述了峰值电流控制的不稳定性及原因,研究了斜坡补偿与系统稳定性的关系,给出了实际斜坡补偿电路及设计方法。 相似文献
17.
LTC1624是一款高性能电流型脉宽调制控制器,芯片内部应用了峰值电流控制技术,芯片工作频率固定,占空比最大可以达到95%。该文分析了峰值电流控制技术的基本原理和特点,简单介绍了LTC1624的工作原理,并以实验进行论证。实验结果表明,LTC1624是一款性能优越的电流型控制芯片。 相似文献
18.
Charge control: modeling, analysis, and design 总被引:5,自引:0,他引:5
There are many ways to use the inductor current of a PWM converter as part of its feedback control mechanism. A simple and widely used method is peak current-mode control which uses the instantaneous inductor current as part of the control signals. Charge control is a special type of current-mode control. It uses the integration of the on-time inductor current as the feedback control signal. The characteristics of charge control are studied. A complete small-signal analysis is performed for the control scheme. Subharmonic oscillation similar to that of peak current-mode control is found, and the relationship between subharmonic oscillation and the line/load condition of charge control is defined. Based on the analysis, design guidelines which guarantee the stability of the control system under given line and load ranges are proposed. The small-signal model was confirmed experimentally 相似文献
19.