CBM and CO2-ECBM related sorption processes in coal: A review

This article reviews the state of research on sorption of gases (CO₂, CH₄) and water on coal for primary recovery of coalbed methane (CBM), secondary recovery by an enhancement with carbon dioxide injection (CO₂-ECBM), and for permanent storage of CO₂ in coal seams.Especially in the last decade a large amount of data has been published characterizing coals from various coal basins world-wide for their gas sorption capacity. This research was either related to commercial CBM production or to the usage of coal seams as a permanent sink for anthropogenic CO₂ emissions. Presently, producing methane from coal beds is an attractive option and operations are under way or planned in many coal basins around the globe. Gas-in-place determinations using canister desorption tests and CH₄ isotherms are performed routinely and have provided large datasets for correlating gas transport and sorption properties with coal characteristic parameters.Publicly funded research projects have produced large datasets on the interaction of CO₂ with coals. The determination of sorption isotherms, sorption capacities and rates has meanwhile become a standard approach.In this study we discuss and compare the manometric, volumetric and gravimetric methods for recording sorption isotherms and provide an uncertainty analysis. Using published datasets and theoretical considerations, water sorption is discussed in detail as an important mechanisms controlling gas sorption on coal. Most sorption isotherms are still recorded for dry coals, which usually do not represent in-seam conditions, and water present in the coal has a significant control on CBM gas contents and CO₂ storage potential. This section is followed by considerations of the interdependence of sorption capacity and coal properties like coal rank, maceral composition or ash content. For assessment of the most suitable coal rank for CO₂ storage data on the CO₂/CH₄ sorption ratio data have been collected and compared with coal rank.Finally, we discuss sorption rates and gas diffusion in the coal matrix as well as the different unipore or bidisperse models used for describing these processes.This review does not include information on low-pressure sorption measurements (BET approach) to characterize pore sizes or pore volume since this would be a review of its own. We also do not consider sorption of gas mixtures since the data base is still limited and measurement techniques are associated with large uncertainties.     

Methane and carbon dioxide sorption on a set of coals from India

Complete sorption isotherm characteristics of methane and CO₂ were studied on fourteen sub-bituminous to high-volatile bituminous Indian Gondwana coals. The mean vitrinite reflectance values of the coal samples are within the range of 0.64% to 1.30% with varying maceral composition. All isotherms were conducted at 30 °C on dry, powdered coal samples up to a maximum experimental pressure of ~ 7.8 MPa and 5.8 MPa for methane and CO₂, respectively.The nature of the isotherms varied widely within the experimental pressure range with some of the samples remained under-saturated while the others attained saturation. The CO₂ to methane adsorption ratios decreased with the increase in experimental pressure and the overall variation was between 4:1 and 1.5:1 for most of the coals. For both methane and CO₂, the lower-ranked coal samples generally exhibited higher sorption affinity compared to the higher-ranked coals. However, sorption capacity indicates a U-shaped trend with rank. Significant hysteresis was observed between the ad/desorption isotherms for CO₂. However, with methane, hysteresis was either absent or insignificant. It was also observed that the coal maceral compositions had a significant impact on the sorption capacities for both methane and CO₂. Coals with higher vitrinite contents showed higher capacities while internite content indicated a negative impact on the sorption capacity.     

Selection of coals of different maturities for CO2 Storage by modelling of CH4 and CO2 adsorption isotherms

CO₂ injection in unmineable coal seams could be one interesting option for both storage and methane recovery processes. The objective of this study is to compare and model pure gas sorption isotherms (CO₂ and CH₄) for well-characterised coals of different maturities to determine the most suitable coal for CO₂ storage. Carbon dioxide and methane adsorption on several coals have been investigated using a gravimetric adsorption method. The experiments were carried out using both CO₂ and CH₄ pure gases at 25 °C from 0.1 to 5 MPa (1 to 50 bar). The experimental results were fitted using Temkin's approach but also with the corrected Langmuir's and the corrected Tóth's equations. The two last approaches are more accurate from a thermodynamical point of view, and have the advantage of taking into account the fact that experimental data (isotherms) correspond to excess adsorption capacities. These approaches allow better quantification of the adsorbed gas. Determined CO₂ adsorption capacities are from 0.5 to 2 mmol/g of dry coal. Modelling provides also the affinity parameters of the two gases for the different coals. We have shown these parameters determined with adsorption models could be used for classification and first selection of coals for CO₂ storage. The affinity ratio ranges from a value close to 1 for immature coals to 41 for high rank coals like anthracites. This ratio allows selecting coals having high CO₂ adsorption capacities. In our case, the modelling study of a significant number of coals from various ranks shows that anthracites seem to have the highest CO₂ storage capacities. Our study provides high quality affinity parameters and values of CO₂ and CH₄ adsorption capacities on various coals for the future modelling of CO₂ injection in coal seams.     

Methane and carbon dioxide adsorption–diffusion experiments on coal: upscaling and modeling

Numerical modelling of the processes of CO₂ storage in coal and enhanced coalbed methane (ECBM) production requires information on the kinetics of adsorption and desorption processes. In order to address this issue, the sorption kinetics of CO₂ and CH₄ were studied on a high volatile bituminous Pennsylvanian (Upper Carboniferous) coal (VR_r=0.68%) from the Upper Silesian Basin of Poland in the dry and moisture-equilibrated states. The experiments were conducted on six different grain size fractions, ranging from <0.063 to 3 mm at temperatures of 45 and 32 °C, using a volumetric experimental setup. CO₂ sorption was consistently faster than CH₄ sorption under all experimental conditions. For moist coals, sorption rates of both gases were reduced by a factor of more than 2 with respect to dry coals and the sorption rate was found to be positively correlated with temperature. Generally, adsorption rates decreased with increasing grain size for all experimental conditions.Based on the experimental results, simple bidisperse modelling approaches are proposed for the sorption kinetics of CO₂ and CH₄ that may be readily implemented into reservoir simulators. These approaches consider the combination of two first-order reactions and provide, in contrast to the unipore model, a perfect fit of the experimental pressure decay curves. The results of this modeling approach show that the experimental data can be interpreted in terms of a fast and a slow sorption process. Half-life sorption times as well as the percentage of sorption capacity attributed to each of the two individual steps have been calculated.Further, it was shown that an upscaling of the experimental and modelling results for CO₂ and CH₄ can be achieved by performing experiments on different grain size fractions under the same experimental conditions.In addition to the sorption kinetics, sorption isotherms of the samples with different grain size fractions have been related to the variations in ash and maceral composition of the different grain size fractions.     

Sorption of carbon dioxide–methane mixtures

The paper reports the results of experiments concerning the sorption/desorption processes, observed under laboratory conditions, in two types of coal extracted from operational coal-mines in Poland, using CH₄ and CO₂ to observe their relative inter-reaction with the coal samples when introduced in varying proportions and conditions. Numerous studies concerning the sorption/desorption phenomena have described the operational mechanisms and the relationship of mine gases to the organically-created coal-body in mines. The differences in the behaviour of certain gases is twofold: firstly the essentially different characteristics of CO₂ and CH₄, and secondly the structure of the coal-bed itself: its degree of metamorphism and content of macerals. From the results yielded, it was observed that the divergence of the isotherms of sorption of CH₄ and other gases in comparison with the isotherms of sorption of CO₂ and a CO₂/CH₄ mixture differed and that the curve on the sorption isotherm was more clearly distinct after the introduction of CO₂ molecules to the system: coal with a higher degree of metamorphism—CH₄, which is closely related to the rigidity of the structure according to the level of metamorphism. Since coals with higher carbon content exhibit lower molecular bonding than low-carbonised coals, the characteristic feature of the bonds in the first case is their mobility. Knowledge of the physical and chemical properties of hard coals, as well as their interaction with mining gases, is of great use in solving problems concerned with the extraction of methane from mines or its storage in goafs.     

Supercritical gas sorption on moist coals

The effect of moisture on the CO₂ and CH₄ sorption capacity of three bituminous coals from Australia and China was investigated at 55 °C and at pressures up to 20 MPa. A gravimetric apparatus was used to measure the gas adsorption isotherms of coal with moisture contents ranging from 0 to about 8%. A modified Dubinin–Radushkevich (DR) adsorption model was found to fit the experimental data under all conditions. Moisture adsorption isotherms of these coals were measured at 21 °C. The Guggenheim–Anderson–de Boer (GAB) model was capable of accurately representing the moisture isotherms over the full range of relative pressures.Moist coal had a significantly lower maximum sorption capacity for both CO₂ and CH₄ than dry coal. However, the extent to which the capacity was reduced was dependent upon the rank of the coal. Higher rank coals were less affected by the presence of moisture than low rank coals. All coals exhibited a certain moisture content beyond which further moisture did not affect the sorption capacity. This limiting moisture content was dependent on the rank of the coal and the sorbate gas and, for these coals, corresponded approximately to the equilibrium moisture content that would be attained by exposing the coal to about 40–80% relative humidity. The experimental results indicate that the loss of sorption capacity by the coal in the presence of water can be simply explained by volumetric displacement of the CO₂ and CH₄ by the water. Below the limiting moisture content, the CO₂ sorption capacity reduced by about 7.3 kg t^− 1 for each 1% increase in moisture. For CH₄, sorption capacity was reduced by about 1.8 kg t^− 1 for each 1% increase in moisture.The heat of sorption calculated from the DR model decreased slightly on addition of moisture. One explanation is that water is preferentially attracted to high energy adsorption sites (that have high energy by virtue of their electrostatic nature), expelling CO₂ and CH₄ molecules.     

Displacement behavior of CH4 adsorbed on coals by injecting pure CO2, N2, and CO2–N2 mixture

Gas adsorption isotherms of Akabira coals were established for pure carbon dioxide (CO₂), methane (CH₄), and nitrogen (N₂). Experimental data fit well into the Langmuir model. The ratio of sorption capacity of CO₂, CH₄, and N₂ is 8.5:3.5:1 at a lower pressure (1.2 MPa) regime and becomes 5.5:2:1 when gas pressure increases to 6.0 MPa. The difference in sorption capacity of these three gases is explained by differences in the density of the three gases with increasing pressure. A coal–methane system partially saturated with CH₄ at 2.4 MPa adsorption pressure was experimentally studied. Desorption behavior of CH₄ by injecting pure CO₂ (at 3.0, 4.0, 5.0, and 6.0 MPa), and by injecting the CO₂–N₂ mixture and pure N₂ (at 3.0 and 6.0 MPa) were evaluated. Results indicate that the preferential sorption property of coal for CO₂ is significantly higher than that for CH₄ or N₂. CO₂ injection can displace almost all of the CH₄ adsorbed on coal. When modeling the CH₄–CO₂ binary and CH₂–CO₂–N₂ ternary adsorption system by using the extended Langmuir (EL) equation, the EL model always over-predicted the sorbed CO₂ value with a lower error, while under-predicting the sorbed CH₄ with a higher error. A part of CO₂ may dissolve into the solid organic structure of coal, besides its competitive adsorption with other gases. According to this explanation, the EL coefficients of CO₂ in EL equation were revised. The revised EL model proved to be very accurate in predicting sorbed ratio of multi-component gases on coals.     

Flue gas and pure CO2 sorption properties of coal: A comparative study

Presently many research projects focus on the reduction of anthropogenic CO₂ emissions. It is intended to apply underground storage techniques such as flue gas injection in unminable coal seams. In this context, an experimental study has been performed on the adsorption of pure CO₂ and preferential sorption behavior of flue gas. A coal sample from the Silesian Basin in Poland (0.68% V Rr), measured in the dry and wet state at 353 K has been chosen for this approach. The flue gas used was a custom class industrial flue gas with 10.9% of CO₂, 0.01% of CO, 9% of H₂, 3.01% of CH₄, 3.0% of O₂, 0.106% of SO₂ and nitrogen as balance.Adsorption isotherms of CO₂ and flue gas were measured upto a maximum of 11 MPa using a volumetric method. Total excess sorption capacities for CO₂ on dry and wet Silesia coal ranged between 1.9 and 1.3 mmol/g, respectively. Flue gas sorption capacities on dry and wet Silesia coal were much lower and ranged between 0.45 and 0.2 mmol/g, respectively, at pressures of 8 MPa. The low sorption capacity of wet coal has resulted from water occupying some of the more active adsorption sites and hence reducing the heterogeneity of adsorption sites relative to that of dry coal. Desorption tests with flue gas were conducted to study the degree of preferential sorption of the individual components. These experiments indicate that CO₂ is by far the prefered sorbing component under both wet and dry conditions. This is followed by CH₄. N₂ adsorbs very little on the coal in the presence of CO₂ and CH₄. It is also observed that the adsorption of CO₂ onto coal is not significantly hindered by the addition of other gases, other than dilution effect of the pressure.In addition to the sorption experiments, the density of the flue gas mixture has been determined up to 18 MPa at 318 K. A very good precision of these measurements were documented by volumetric methods.     

Binary gas sorption/desorption experiments on a bituminous coal: Simultaneous measurements on sorption kinetics,volumetric strain and acoustic emission

There is still no clear understanding of the specific interactions between coal and gas molecules. In this context sorption–desorption studies of methane and carbon dioxide, both in a single gas environment and gas mixtures, are of fundamental interest. This paper presents the results of unique simultaneous measurements of sorption kinetics, volumetric strain and acoustic emission (AE) on three tetragonal coal samples subjected to sorption of carbon dioxide and methane mixtures. The coal was a high volatile bituminous C coal taken from the Budryk mine in the Upper Silesia Basin, Poland. Three different gas mixtures were used in the sorption tests, with dominant CO₂, with dominant CH₄ and a 50/50 mixture.The experimental set-up was designed specially for this study. It consisted of three individual units working together: (i) a unit for gas sorption experiments using a volumetric method, (ii) an AE apparatus for detecting, recording and analysing AE, and (iii) a strain meter for measuring strains induced in the coal sample by gas sorption/desorption. All measurements were computer aided.The experiments indicated that the coal tested showed preferential sorption of CH₄ at 2.6 MPa pressure and exhibited comparable affinities for CH₄ and CO₂ at higher pressures (4.0 MPa). The results of chromatographic analysis of the gas released on desorption suggested that the desorption of methane from the coal was favoured. The relationship between the volumetric strain and the amount of sorbed gas was found to be non-linear. These results were contrary to common opinions on the coal behaviour. Furthermore, it appeared that the swelling/shrinkage of coal was clearly influenced by the network of fractures. Besides, the AE and strain characteristics suggested common sources of sorption induced AE and strain.The present results may have implications for the sequestration of carbon dioxide in coal seams and enhanced coalbed methane recovery (ECBM).     

http://www.sciencedirect.com/science/article/pii/S1674987112000308

The Panguan Syncline contains abundant coal resources,which may be a potential source of coalbed methane.In order to evaluate the coalbed methane production potential in this area,we investigated the pore-fracture system of coalbed methane reservoirs,and analyzed the gas sorption and seepage capacities by using various analytical methods,including scanning electron microscopy（SEM）,optical microscopy,mercury-injection test,low-temperature N₂ isotherm adsorption/desorption analyses,lowfield nuclear magnetic resonance and methane isothermal adsorption measurements.The results show that the samples of the coal reservoirs in the Panguan Syncline have moderate gas sorption capacity.However, the coals in the study area have favorable seepage capacities,and are conductive for the coalbed methane production.The physical properties of the coalbed methane reservoirs in the Panguan Syncline are generally controlled by coal metamorphism:the low rank coal usually has low methane sorption capacity and its pore and microfractures are poorly developed;while the medium rank coal has better methane sorption capacity,and its seepage pores and microfractures are well developed,which are sufficient for the coalbed methane’s gathering and exploration.Therefore,the medium rank coals in the Panguan Syncline are the most prospective targets for the coalbed methane exploration and production.     

On the effects of petrographic composition on coalbed methane sorption

The effect of petrographic composition on the methane sorption capacity has been determined for a suite of coals and organic-rich shales. Subbituminous and bituminous coals were separated into bright and dull lithotypes by hand-picking. The methane sorption capacities range between 0.5 and 23.9 cm³/g at a pressure of 6 MPa. The low volatile bituminous Canmore coal and the anthracite sample have the highest capacities with the “natural coke” having the lowest. For low-rank coals there is no significant difference between bright and dull samples except for one coal with the dull sample having a greater sorption capacity than its bright equivalent. For higher-rank coals, the bright samples have a greater methane capacity than the dull samples and the difference between sample pairs increases with rank. The boghead coal samples have the highest sorption capacities in the liptinite-rich coals suite and are higher than subbituminous to medium volatile bituminous samples. Pore size distribution indicates that methane is held as solution gas in liptinite-rich coals and by physical sorption in micropores in liptinite-poor coals. These contrasting processes illustrate that liptinite-rich samples need to be independently assessed. The positive relationship between reactive inertinite content and methane sorption capacity occurs within the subbituminous to medium volatile bituminous coals because the reactive inertinite is structurally similar to vitrinite and have a higher microporosity than non-reactive inertinite. Reactivity of inertinite should be assessed in CBM studies of dull coals to provide a better understanding of petrographic composition effects on methane capacity.     

Interpretation of carbon dioxide diffusion behavior in coals

Storage of carbon dioxide in geological formations is for many countries one of the options to reduce greenhouse gas emissions and thus to satisfy the Kyoto agreements. The CO₂ storage in unminable coal seams has the advantage that it stores CO₂ emissions from industrial processes and can be used to enhance coalbed methane recovery (CO₂-ECBM). For this purpose, the storage capacity of coal is an important reservoir parameter. While the amount of CO₂ sorption data on various natural coals has increased in recent years, only few measurements have been performed to estimate the rate of CO₂ sorption under reservoir conditions. An understanding of gas transport is crucial for processes associated with CO₂ injection, storage and enhanced coalbed methane (ECBM) production.A volumetric experimental set-up has been used to determine the rate of sorption of carbon dioxide in coal particles at various pressures and various grain size fractions. The pressure history during each pressure step was measured. The measurements are interpreted in terms of temperature relaxation and transport/sorption processes within the coal particles. The characteristic times of sorption increase with increasing pressure. No clear dependence of the characteristic time with respect to the particle size was found. At low pressures (below 1 MPa) fast gas diffusion is the prevailing mechanism for sorption, whereas at higher pressures, the slow diffusion process controls the gas uptake by the coal.     

Polycyclic aromatic hydrocarbons (PAHs) in Chinese coal: occurrence and sorption mechanism

Elevated polycyclic aromatic hydrocarbon (PAH) concentrations were determined in different Chinese coals, with the highest concentrations in bituminous coals. Phenanthrene (Phen) was chosen as the probe compound for PAHs to study the sorption behavior of coal. No native Phen was detected in desorption experiments indicating irreversible sorption–desorption behavior of PAHs in raw coal samples. Sorption mechanism was further studied under varying conditions of pH value and ionic strength. Different ranks of coal showed different sorption behavior under acidic, neutral, and alkaline conditions. Batch experiments were further processed for the selected coals at pH values from 3 to 11 at a constant aqueous concentration. Sorption capacities of all coals decreased with increased pH except for YJ coal. Furthermore, although DOC-associated Phen mass contributed little to the total Phen mass under different pH values, the significant negative correlations between M _DOC and log K _OC values were observed for all coal samples, indicating a significant role played by DOC in the coal sorption. In addition, sorption experiments under varying ionic strength showed that the ionic strength influence was more obvious in sorption isotherms for higher rank coals with increasing ionic strength, and this effect was most significant when ionic strength increased from 0 to 0.15 M, especially at relatively low aqueous concentrations.     

Properties of thermally metamorphosed coal from Tanjung Enim Area, South Sumatra Basin, Indonesia with special reference to the coalification path of macerals

Thermally metamorphosed Tertiary age coals from Tanjung Enim in South Sumatra Basin have been investigated by means of petrographic, mineralogical and chemical analyses. These coals were influenced by heat from an andesitic igneous intrusion. The original coal outside the metamorphosed zone is characterized by high moisture content (4.13–11.25 wt.%) and volatile matter content (> 40 wt.%, daf), as well as less than 80 wt.% (daf) carbon and low vitrinite reflectance (VR_max = 0.52–0.76%). Those coals are of subbituminous and high volatile bituminous rank. In contrast the thermally metamorphosed coals are of medium-volatile bituminous to meta-anthracite rank and characterized by low moisture content (only < 3 wt.%) and volatile matter content (< 24 wt.%, daf), as well as high carbon content (> 80 wt.%, daf) and vitrinite reflectance (VR_max = 1.87–6.20%). All the studied coals have a low mineral matter content, except for those which are highly metamorphosed, due to the formation of new minerals.The coalification path of each maceral shows that vitrinite, liptinite and inertinite reflectance converge in a transition zone at VR_max of around 1.5%. Significant decrease of volatile matter occurs in the zone between 0.5% and 2.0% VR_max. A sharp bend occurs at VR_max between 2.0% and 2.5%. Above 2.5%, the volatile matter decreases only very slightly. Between VR_r = 0.5% and 2.0%, the carbon content of the coals is ascending drastically. Above 2.5% VR_r, the carbon content becomes relatively stable (around 95 wt.%, daf).Vitrinite is the most abundant maceral in low rank coal (69.6–86.2 vol.%). Liptinite and inertinite are minor constituents. In the high rank coal, the thermally altered vitrinite composes 82.4–93.8 vol.%. Mosaic structures can be recognized as groundmasss and crack fillings. The most common minerals found are carbonates, pyrite or marcasite and clay minerals. The latter consist of kaolinite in low rank coal and illite and rectorite in high rank coal. Change of functional groups with rank increase is reflected most of all by the increase of the ratio of aromatic C–H to aliphatic C–H absorbances based on FTIR analysis. The Oxygen Index values of all studied coals are low (OI < 5 mg CO₂/g TOC) and the high rank coals have a lower Hydrogen Index (< 130 mg HC/g TOC) than the low rank coals (about 300 mg HC/g TOC). T_max increases with maturity (420–440 °C for low rank coals and 475–551 °C for high rank coals).Based on the above data, it was calculated that the temperature of contact metamorphism reached 700–750 °C in the most metamorphosed coal.     

Development of the first coal seam gas exploration program in Indonesia: Reservoir properties of the Muaraenim Formation, south Sumatra

The Late Miocene Muaraenim Formation in southern Sumatra contains thick coal sequences, mostly of low rank ranging from lignite to sub-bituminous, and it is believed that these thick low rank coals are the most prospective for the production of coal seam gas (CSG), otherwise known as coalbed methane (CBM), in Indonesia.As part of a major CSG exploration project, gas exploration drilling operations are being undertaken in Rambutan Gasfields in the Muaraenim Formation to characterize the CSG potential of the coals. The first stage of the project, which is described here, was designed to examine the gas reservoir properties with a focus on coal gas storage capacity and compositional properties. Some five CSG exploration boreholes were drilled in the Rambutan Gasfield, south of Palembang. The exploration boreholes were drilled to depths of ~ 1000 m into the Muaraenim Formation. Five major coal seams were intersected by these holes between the depths of 450 and 1000 m. The petrography of coal samples collected from these seams showed that they are vitrinite rich, with vitrinite contents of more than 75% (on a mineral and moisture free basis). Gas contents of up to 5.8 m³/t were measured for the coal samples. The gas desorbed from coal samples contain mainly methane (CH₄) ranging from 80 to 93% and carbon dioxide (CO₂) ranging from 6 to 19%. The composition of the gas released into the production borehole/well is, however, much richer in CH₄ with about 94 to 98% CH₄ and less than 5% CO₂.The initial results of drilling and reservoir characterization studies indicate suitable gas recovery parameters for three of the five coal seams with a total thickness of more than 30 m.     

The structural evolution of organic matter during maturation of coals and its impact on petroleum potential and feedstock for the deep biosphere

The structural evolution of coals during coalification from peat to the end of the high volatile bituminous coal rank (VR_r = 0.22–0.81%) has been studied using a natural maturity series from New Zealand. Samples were studied using a range of standard coal analyses, Rock–Eval analysis, infrared spectroscopy (IR), X-ray photoelectron spectroscopy (XPS), and pyrolysis gas chromatography (Py-GC). The structural evolution of coal during diagenesis and moderate catagenesis is dominated by defunctionalisation reactions leading to the release of significant amounts of oxygen and thereby to an enrichment of aromatic as well as aliphatic structures within the residual organic matter. Based on the evolution of pyrolysis yields and elemental compositions with maturity it can be demonstrated that oxygen loss is the major cause for increasing Hydrogen Index values or hydrocarbon generating potentials of coals at such maturity levels. For the first time, the loss of oxygen in form of CO₂ has been quantified. During maturation from peat to high volatile bituminous coal ranks ∼10–105 mg CO₂/g TOC has been released. This is equivalent to 2.50E−4 to 1.25E−3 mg CO₂ generated from every litre of sediment per year falling into the range of deep biosphere utilisation rates. Immature coals, here New Zealand coals, therefore manifest the potential to feed deep terrestrial microbial life, in contrast to more mature coals (VR_r > ∼0.81%) for which defunctionalisation processes become less important.     

Preliminary reservoir model of enhanced coalbed methane (ECBM) in a subbituminous coal seam,Huntly Coalfield,New Zealand

The Huntly coalfield has significant coal deposits that contain biogenically-sourced methane. The coals are subbituminous in rank and Eocene in age and have been previously characterised with relatively low to moderate measured gas (CH₄) contents (2–4 m³/ton). The CO₂ holding capacity is relatively high (18.0 m³/ton) compared with that of CH₄ (2.6 m³/ton) and N₂ (0.7 m³/ton) at the same pressure (4 MPa; all as received basis). The geothermal gradient is also quite high at 55 °C/km.A study has been conducted which simulates enhancement of methane recovery (ECBM) from these deposits using a new version of the TOUGH2 (version 2) reservoir simulator (ECBM-TOUGH2) that can handle non-isothermal, multi-phase flows of mixtures of water, CH₄, CO₂ and N₂. The initial phase of the simulation is CH₄ production for the first 5 years of the field history. The model indicates that methane production can be significantly improved (from less than 80% recovery to nearly 90%) through injection of CO₂. However, although an increase in the rate of CO₂ injection increases the amount of CO₂ sequestered, the methane recovery (because of earlier breakthrough with increasing injection rate) decreases. Modeling of pure N₂ injection produced little enhanced CH₄ production. The injection of a hypothetical flue gas mixture (CO₂ and N₂) also produced little increase in CH₄ production. This is related to the low adsorption capacity of the Huntly coal to N₂ which results in almost instantaneous breakthrough into the production well.     

A review of coal properties pertinent to carbon dioxide sequestration in coal seams: with special reference to Victorian brown coals

This paper presents reviews of studies on properties of coal pertinent to carbon dioxide (CO₂) sequestration in coal with specific reference to Victorian brown coals. The coal basins in Victoria, Australia have been identified as one of the largest brown coal resources in the world and so far few studies have been conducted on CO₂ sequestration in this particular type of coals. The feasibility of CO₂ sequestration depends on three main factors: (1) coal mass properties (chemical, physical and microscopic properties), (2) seam permeability, and (3) gas sorption properties of the coal. Firstly, the coal mass properties of Victorian brown coal are presented, and then the general variations of the coal mass properties with rank, for all types of coal, are discussed. Subsequently, coal gas permeability and gas sorption are considered, and the physical factors which affect them are examined. In addition, existing models for coal gas permeability and gas sorption in coal are reviewed and the possibilities of further development of these models are discussed. According to the previous studies, coal mass properties and permeability and gas sorption characteristics of coals are different for different ranks: lignite to medium volatile bituminous coals and medium volatile bituminous to anthracite coals. This is important for the development of mathematical models for gas permeability and sorption behavior. Furthermore, the models have to take into account volume effect which can be significant under high pressure and temperature conditions. Also, the viscosity and density of supercritical CO₂ close to the critical point can undergo large and rapid changes. To date, few studies have been conducted on CO₂ sequestration in Victorian brown coal, and for all types of coal, very few studies have been conducted on CO₂ sequestration under high pressure and temperature conditions.     

Contact angles in CO2-water-coal systems at elevated pressures

Injection of carbon dioxide into coal seams is considered to be a potential method for its sequestration away from the atmosphere. However, water present in coals may retard injection: especially if carbon dioxide does not wet the coal as well as water. Thus contact angles in the coal-water-CO₂ system were measured using CO₂ bubbles in water/coal systems at 40 °C and pressures up to 15 MPa using five bituminous coals. At low pressures, in this CO₂/water/coal system, receding contact angles for the coals ranged between 80° to 100°; except for one coal that had both high ash yield and low rank, with a contact angle of 115°, indicating that it was hydrophilic. With increasing pressure, the receding contact angles for the different coals decreased, indicating that they became more CO₂-wetting. The relationship between contact angle and pressure was approximately linear. For low ash or high rank coals, at high pressure the contact angle was reduced to 30-50°, indicating the coals became strongly CO₂-wetting; that is CO₂ fluids will spontaneously penetrate these wet coals. In the case of the coal that was both high ash and hydrophilic, the contact angle did not drop to 90° even at the highest pressures used. These results suggest that CO₂ will not be efficiently adsorbed by all wet coals equally well, even at high pressure. It was found that at high pressures (> 2 MPa) the rate of penetration of carbon dioxide into the coals increased rapidly with decreasing contact angle, independently of pressure. Injecting CO₂ into wet coals that have both low rank and high ash will not trap CO₂ as well as injecting it into high rank or low ash coals.     

Effects of coal storage in air on physical and chemical properties of coal and on gas adsorption

This paper investigates changes in the high-volatile bituminous Lower Block Coal Member from Indiana owing to moisture availability and oxidation in air at ambient pressure and temperature over storage time. Specifically, it investigates changes in chemistry, in surface area, and pore structure, as well as changes in methane and carbon dioxide adsorption capacities. Our results document that the methane adsorption capacity increased by 40%, whereas CO₂ adsorption capacity increased by 18% during a 13-month time period. These changes in adsorption are accompanied by changes in chemistry and surface area of the coal.The observed changes in adsorption capacity indicate that special care must be taken when collecting samples and preserving coals until adsorption characteristics are measured in the laboratory. High-pressure isotherms from partially dried coal samples would likely cause overestimation of gas adsorption capacities, lead to a miscalculation of coal-bed methane prospects, and provide deceptively optimistic prognoses for recovery of coal-bed methane or capture of anthropogenic CO₂.