Development of Processing Map for 7075 Al/20% SiCp Composite

The hot deformation behavior and microstructure evolution of 7075 Al/20% SiC_p composite have been studied using the processing map. Compression tests were carried out in the temperature range of 300-500 °C and at the strain rate range of 0.001-1.0 s⁻¹. The stable and unstable regions in the map were verified with the microstructural observations of the deformed compression specimens. The “stable” regions, i.e., dynamic recrystallization and “unstable” regions such as debonding of SiC particles, matrix crack, and adiabatic shear band formation were identified from the processing map and compared with the reported microstructural observations of the deformed compression specimens. The optimum hot working conditions for this composite were identified.     

Processing map and microstructure evaluation of AA6061/Al2O3 nanocomposite at different temperatures

Hot compression behavior of Al6061/Al₂O₃ nanocomposite was investigated in the temperature range of 350–500 °C and the strain rate range of 0.0005–0.5 s^?1, in order to determine the optimum conditions for the hot workability of nanocomposite. The activation energy of 285 kJ/mol for the hot compression test is obtained by using hyperbolic sine function. By means of dynamic material model (DMM) and the corresponding processing map, safe zone for the hot workability of AA6061/Al₂O₃ is recognized at temperature of 450 °C and strain rate of 0.0005 s^?1 and at temperature of 500 °C and the strain rate range of 0.0005–0.5 s^?1, with the maximum power dissipation efficiency of 38%. Elongated and kinked grains are observed at 400 °C and strain rate of 0.5 s^?1 due to the severe deformation.     

Hot Deformation Behavior and Processing Maps of 2099 Al-Li Alloy

Hot deformation behavior and processing maps of the 2099 Al-Li alloy are investigated by tensile test at the temperature range from 250 to 450 °C and the strain rate range from 0.001 to 5.0 s^?1. The typical true stress-true strain curves show that the flow stress increases with increasing the strain rate and decreasing the deforming temperature. All curves exhibit rapid work hardening at an initial stage of strain followed by remarkable dynamic softening. Based on the flow stress behavior, the processing maps are calculated and analyzed according to the dynamic materials model (DMM). The processing maps exhibit an instability domain in the temperature and strain rate ranges: T = 250-260 °C and \(\dot{\upvarepsilon }\)  = 0.1-0.5 s^?1. The maps also exhibit an optimum hot working condition in the stability domain that occurs in the temperature of 400 °C for a strain rate of 0.001 s^?1 and having a maximum efficiency of 60%. The microstructural examinations exhibit the occurrence of dynamic recovery (DRV) during hot deformation of the 2099 alloy which is the dominant softening mechanism in the alloy. The fracture behavior changes from a brittle fracture to a ductile fracture as strain rate decreases and temperature increases.     

Characterization of hot deformation and microstructure evolution of a new metastable β titanium alloy

The hot deformation characteristics of as-forged Ti?3.5Al?5Mo?6V?3Cr?2Sn?0.5Fe?0.1B?0.1C alloy within a temperature range from 750 to 910 °C and a strain rate range from 0.001 to 1 s^?1 were investigated by hot compression tests. The stress?strain curves show that the flow stress decreases with the increase of temperature and the decrease of strain rate. The microstructure is sensitive to deformation parameters. The dynamic recrystallization (DRX) grains appear while the temperature reaches 790 °C at a constant strain rate of 0.001 s^?1 and strain rate is not higher than 0.1 s^?1 at a constant temperature of 910 °C. The work-hardening rate θ is calculated and it is found that DRX prefers to happen at high temperature and low strain rate. The constitutive equation and processing map were obtained. The average activation energy of the alloy is 242.78 kJ/mol and there are few unstable regions on the processing map, which indicates excellent hot workability. At the strain rate of 0.1 s^?1, the stress?strain curves show an abnormal shape where there are two stress peaks simultaneously. This can be attributed to the alternation of hardening effect, which results from the continuous dynamic recrystallization (CDRX) and the rotation of DRX grains, and dynamic softening mechanism.     

脉冲电场下的7075双辊铸轧板热变形行为

在变形温度250~350 ℃和应变速率0.001~0.01 s^-1的条件下进行热拉伸试验,研究了厚度为5 mm的7075合金传统铸轧板和电脉冲铸轧板的微观组织和热成形性能。实验用脉冲电流参数为：单周期脉宽0.005 s和峰值强度300 A。结果显示,脉冲电流能够促进凝固过程的枝晶细化,并诱发组织均匀化。由于电磁振荡增强了凝固过程中溶质混合能力,极压电流有效地促进了晶粒细化和析出相的均匀化。同时,面心立方（fcc）铝合金铸轧板织构具有{423}<144>取向,经脉冲电流改性后,取向为{421}<216>。脉冲电流处理后的合金峰值流动应力约为未处理合金的1.1~1.3倍。电子背散射衍射分析表明,脉冲电流通过促进动态再结晶的方式,有效地改善了晶粒的择优分布。在此基础上,分别建立了铝合金带材的双曲正弦方程和含Zener-Holloman参数的本构模型。此外,通过对断口形貌的观察发现,脉冲电流的引入有利于提高7075铝合金的高温机械性能。最后建立了优化的工艺流程图,并确定了适宜的热加工温度为290~330 ℃和应变速率为0.001~0.002 s^-1。     

Optimization of Hot Extrusion Process Parameters of Mg97Y2Zn1 Alloy Based on the Processing Maps

The processing maps of the Mg₉₇Y₂Zn₁ alloy have been developed for optimizing hot workability and controlling the microstructure in this paper. Compression tests were conducted in the temperature range from 250 to 450 °C and the strain rate range from 0.001 to 5.0 s^?1. The processing maps were calculated based on the flow stress behavior and analyzed according to the dynamic materials model. The maps exhibited a stability domain that occurs in the temperature of 430-450 °C for a strain rate of 0.002-0.003 s^?1 and having a maximum efficiency of 50%. A hot extrusion test was carried out to assess the prediction of the processing maps for Mg₉₇Y₂Zn₁ alloy. The influence of the extrusion temperature on the microstructure and tensile properties of the extruded alloys was analyzed to identify the optimum processing parameters. The results have shown good agreement between the regimes exhibited by the map and the microstructure of the extruded alloy.     

Characterization of Hot Deformation Behavior of AMS 5708 Nickel-Based Superalloy Using Processing Map

The hot deformation behavior of AMS 5708 nickel-based superalloy was investigated by means of hot compression tests and a processing map in the temperature range of 950-1200 °C and a strain rate range of 0.01-1 s^?1 was constructed. The true stress-true strain curves showed that the maximum flow stress decreases with the increase of temperature and decrease of strain rate. The developed processing map based on experimental data, showed variations of efficiency of power dissipation relating to temperature and strain rate at constant strain. Interpretation of the processing map showed one stable domain, in which dynamic recrystallization was the dominant microstructural phenomenon, and one instability domain with flow localization. The results of interpretation of flow stress curves and processing map were verified by the microstructure observations. There are two optimum conditions for hot working of this alloy with efficiency peak of 0.36: the first is at 1150 °C for a strain rate of 1 s^?1 that produces a fine grained microstructure. The second is at 1200 °C for a strain rate of 0.01 s^?1 that produces a coarse grained microstructure.     

35% SiC_p/2024A1复合材料的热变形行为(英文)

采用Gleeble-1500D热模拟试验机,对35%SiCp/2024A1复合材料在温度350~500°C、应变速率0.01~10s-1的条件下进行热压缩试验,研究该复合材料的热变形行为与热加工特征,建立热变形本构方程和加工图。结果表明,35%SiCp/2024A1复合材料的流变应力随着温度的升高而降低,随着应变速率的增大而升高,说明该复合材料是正应变速率敏感材料,其热压缩变形时的流变应力可采用Zener-Hollomon参数的双曲正弦形式来描述;在本实验条件下平均热变形激活能为225.4 kJ/mol。为了证实其潜在的可加工性,对加工图中的稳定区和失稳区进行标识,并通过微观组织得到验证。综合考虑热加工图和显微组织,得到变形温度500°C、应变速率0.1~1 s-1是复合材料适宜的热变形条件。     

Hot Compression Deformation Behavior and Processing Maps of Mg-Gd-Y-Zr Alloy

Hot compression deformation behavior and processing maps of the Mg-Gd-Y-Zr alloy were investigated in this paper. Compression tests were conducted at the temperature range from 300 to 450 °C and the strain rate range from 0.001 to 1.0 s^?1. It is found that the flow stress behavior is described by the hyperbolic sine constitutive equation in which the average activation energy of 251.96 kJ/mol is calculated. Through the flow stress behavior, the processing maps are calculated and analyzed according to the dynamic materials model. In the processing maps, the variation of the efficiency of the power dissipation is plotted as a function of temperature and strain rate. The instability domains of flow behavior are identified by the maps. The maps exhibit a domain of dynamic recrystallization occurring at the temperature range of 375-450 °C and strain rate range of 0.001-0.03 s^?1 which are the optimum parameters for hot working of the alloy.     

Optimization of a hot deformation process of the 3003 aluminum alloy by processing maps

Hot deformation behavior of the 3003 Al alloy was investigated by conducting hot compression tests at various temperatures (300?C500 °C) and strain rates (0.0l?C10.0 s^?1). A constitutive equation was established to describe the flow behavior. The apparent activation energy of the 3003 Al alloy was determined to be 174.62 kJ·mol^?1, which is higher than that for self-diffusion in pure Al (165 kJ·mol^?1). Processing maps at a strain of 0.6 for hot working were developed on a dynamic materials model. The maps exhibit a flow instability domain at about 300?C380 °C and 1.0?C10.0 s^?1. Dynamic recrystallization occurs extensively in the temperature range of 450?C500 °C and at the strain rate of 10.0 s^?1. The optimum parameters of hot working for the 3003 Al alloy are confined at 500 °C and 10.0 s^?1 with the highest efficiency (37%).     

Hot deformation behavior of Al–9.0Mg–0.5Mn–0.1Ti alloy based on processing maps

Hot deformation behavior of extrusion preform of the spray-formed Al–9.0Mg–0.5Mn–0.1Ti alloy was studied using hot compression tests over deformation temperature range of 300–450 °C and strain rate range of 0.01–10 s^?1. On the basis of experiments and dynamic material model, 2D processing maps and 3D power dissipation maps were developed for identification of exact instability regions and optimization of hot processing parameters. The experimental results indicated that the efficiency factor of energy dissipate (η) lowered to the minimum value when the deformation conditions located at the strain of 0.4, temperature of 300 °C and strain rate of 1 s^?1. The softening mechanism was dynamic recovery, the grain shape was mainly flat, and the portion of high angle grain boundary (>15°) was 34%. While increasing the deformation temperature to 400 °C and decreasing the strain rate to 0.1 s^?1, a maximum value of η was obtained. It can be found that the main softening mechanism was dynamic recrystallization, the structures were completely recrystallized, and the portion of high angle grain boundary accounted for 86.5%. According to 2D processing maps and 3D power dissipation maps, the optimum processing conditions for the extrusion preform of the spray-formed Al–9.0Mg–0.5Mn–0.1Ti alloy were in the deformation temperature range of 340–450 °C and the strain rate range of 0.01–0.1 s^?1 with the power dissipation efficiency range of 38%–43%.     

Hot working behavior of near alpha titanium alloy analyzed by mechanical testing and processing map

The hot deformation characteristics of the Ti−5.7Al−2.1Sn−3.9Zr−2Mo−0.1Si (Ti-6242S) alloy with an acicular starting microstructure were analyzed using processing map. The uniaxial hot compression tests were performed at temperatures ranging from 850 to 1000 °C and at strain rates of 0.001−1 s⁻¹. The developed processing map was used to determine the safe and unsafe deformation conditions of the alloy in association with the microstructural evolution by SEM and OM. It was recognized that the flow stress revealed differences in flow softening behavior by deformation at 1000 °C compared to the lower deformation temperatures, which was attributed to microstructural changes. The processing map developed for typical strain of 0.7 in two-phase field exhibited high efficiency value of power dissipation of about 55% at 950 °C and 0.001 s⁻¹, basically due to extensive globularization. An increase in strain rate and a decrease in temperature resulted in a decrease in globularization of α lamellae, while α lamellar kinking increased. Eventually, the instability domain of flow behavior was identified in the temperature range of 850−900 °C and at the strain rate higher than 0.01 s⁻¹ reflecting the flow localization and adiabatic shear banding. By considering the power efficiency domains and the microstructural observations, the deformation in the temperature range of 950−1000 °C and strain rate range of 0.001−0.01 s⁻¹ was desirable leading to high efficiencies. It was realized that (950 °C, 0.001 s⁻¹) was the optimum deformation condition for the alloy.     

Deformation behavior and processing maps of Mg-Zn-Y alloy containing I phase at elevated temperatures

The microstructure and mechanical properties of extruded Mg-Zn alloy containing Y element were investigated in temperature range of 300–450 °C and strain rate range of 0.001–1 s^?1 through hot compression tests. Processing maps were used to indicate optimum conditions and instability zones for hot deformation of alloys. For Mg-Zn and Mg-Zn-Y alloys, peak stress, temperature and strain rate were related by hyperbolic sine function, and activation energies were obtained to be 177 and 236 kJ/mol, respectively. Flow curves showed that the addition of Y element led to increase in peak stress and decrease in peak strain, and indicated that DRX started at lower strains in Mg-Zn-Y alloy than in Mg-Zn alloy. The stability domains of Mg-Zn-Y alloy were indicated in two domains as 1) 300 °C, 0.001 s^?1; 350 °C, 0.01–0.1 s^?1 and 400 °C, 0.01 s^?1 and 2) 450 °C, 0.01–0.1 s^?1. Microstructural observations showed that DRX was the main restoration mechanism for alloys, and fully dynamic recrystallization of Mg-Zn-Y alloy was observed at 450 °C. The instability domain in Mg-Zn-Y alloy was located significantly at high strain rates. In addition, the instability zone width of Mg-Zn and Mg-Zn-Y alloys increased with increasing strain, and cracks, twins and severe deformation were considered in these regions.     

Flow stress and dynamic recrystallization behavior of Al-9Mg-1.1Li-0.5Mn alloy during hot compression process

The flow stress behavior of spray-formed Al-9Mg-1.1Li-0.5Mn alloy was studied using thermal simulation tests on a Gleeble-3500 machine over deformation temperature range of 300-450 °C and strain rate of 0.01-10 s^?1. The microstructural evolution of the alloy during the hot compression process was characterized by transmission electron microscopy (TEM) and electron back scatter diffractometry (EBSD). The results show that the flow stress behavior and microstructural evolution are sensitive to deformation parameters. The peak stress level, steady flow stress, dislocation density and amount of substructures of the alloy increase with decreasing deformation temperature and increasing strain rate. Conversely, the high angle grain boundary area increases, the grain boundary is in serrated shape and the dynamic recrystallization in the alloy occurs. The microstructure of the alloy is fibrous-like and the main softening mechanism is dynamic recovery during steady deformation state. The flow stress behavior can be represented by the Zener-Hollomon parameter Z in the hyperbolic sine equation with the hot deformation activation energy of 184.2538 kJ/mol. The constitutive equation and the hot processing map were established. The hot processing map exhibits that the optimum processing conditions for Al-9Mg-1.1Li-0.5Mn alloy are in deformation temperature range from 380 to 450 °C and strain rate range from 0.01 to 0.1 s^?1.     

Hot deformation behavior of novel imitation-gold copper alloy

The hot deformation behavior of a novel imitation-gold copper alloy was investigated with Gleeble–1500 thermo-mechanical simulator in the temperature range of 650–770 °C and strain rate range of 0.001–1.0 s^?1. The hot deformation constitutive equation was established and the thermal activation energy was obtained to be 249.60 kJ/mol. The processing map at a strain of 1.2 was developed. And there are two optimal regions in processing map, namely 650–680 °C, 0.001–0.01 s^?1 and 740–770 °C, 0.01–0.1 s^?1. Optical microscopy was employed to investigate the microstructure evolution of the alloy in the process of deformation. Recrystallized grains and twin crystals were found in microstructures of the hot deformed alloy.     

Flow Stress and Processing Map of a PM 8009Al/SiC Particle Reinforced Composite During Hot Compression

Hot compression tests of 8009Al alloy reinforced with 15% SiC particles (8009Al/15%SiC_p composites) prepared by powder metallurgy (direct hot extrusion methods) were performed on Gleeble-3500 system in the temperature range of 400-550 °C and strain rate range of 0.001-1 s^?1. The processing map based on the dynamic material model was established to evaluate the flow instability regime and optimize processing parameters; the associated microstructural changes were studied by the observations of optical metallographic and scanning electron microscopy. The results showed that the flow stress increased initially and reached a plateau after peak stress value with increasing strain. The peak stress increased as the strain rate increased and deformation temperature decreased. The optimum parameters were identified to be deformation temperature range of 500-550 °C and strain rate range of 0.001-0.02 s^?1 by combining the processing map with microstructural observation.     

Microstructure characterization of Al-cladded Al–Zn–Mg–Cu sheet in different hot deformation conditions

Al-cladded Al–Zn–Mg–Cu sheets were compressed up to 70% reduction on a Gleeble–3500 thermo-mechanical simulator with temperatures ranging from 380 to 450 °C at strain rates between 0.1 and 30 s^?1. The microstructures of the Al cladding and the Al–Zn–Mg–Cu matrix were characterized by electron back-scattered diffraction (EBSD) and X-ray diffraction (XRD). The microstructure is closely related to the level of recovery and recrystallization, which can be influenced by deformation temperature, deformation pass and deformation rate. The level of recovery and recrystallization are different in the Al cladding and the Al–Zn–Mg–Cu matrix. Higher deformation temperature results in higher degree of recrystallization and coarser grain size. Static recrystallization and recovery can happen during the interval of deformation passes. Higher strain rate leads to finer sub-grains at strain rate below 10 s^?1; however, dynamic recovery and recrystallization are limited at strain rate of 30 s^?1 due to shorter duration at elevated temperatures.     

A Study on the Hot Deformation Behavior of Cast Mg-4Sn-2Ca (TX42) Alloy

The hot deformation behavior of as-cast Mg-4Sn-2Ca (TX42) alloy has been studied using compression tests in the temperature range of 300°C to 500°C, and strain rate range of 0.0003 s^?1 to 10 s^?1. Based on the flow stress data, a processing map has been developed, which exhibited two domains of dynamic recrystallization in the temperature and strain rate ranges: (I) 300°C to 380°C and 0.0003 s^?1 to 0.001 s^?1, and (II) 400°C to 500°C and 0.004 s^?1 to 6 s^?1. While hot working may be conducted in either of these domains, the resulting grain sizes are finer in the first domain than in the second. The apparent activation energy values estimated by kinetic analysis of the temperature and strain rate dependence of flow stress in the domains 1 and 2 are 182 kJ/mol and 179 kJ/mol, respectively. Both the values are much higher than that for self-diffusion in pure magnesium, indicating that the thermally stable CaMgSn particles in the matrix cause significant back stress during the hot deformation of this alloy. The alloy exhibits a regime of flow instability at lower temperatures and higher strain rates, which manifested as flow localization.     

The Use of ANN to Predict the Hot Deformation Behavior of AA7075 at Low Strain Rates

In this study, artificial neural network (ANN) was used to model the hot deformation behavior of 7075 aluminum alloy during compression test, in the strain rate range of 0.0003-1 s^?1 and temperature range of 200-450 °C. The inputs of the model were temperature, strain rate, and strain, while the output of the model was the flow stress. The feed-forward back-propagation network with two hidden layers was built and successfully trained at different deformation domains by Levenberg-Marquardt training algorithm. Comparative analysis of the results obtained from the hyperbolic sine, the power law constitutive equations, and the ANN shows that the newly developed ANN model has a better performance in predicting the hot deformation behavior of 7075 aluminum alloy.     

High temperature deformation and processing map of a NiTi intermetallic alloy

The deformation behavior of a 49.8 Ni-50.2 Ti (at pct) alloy was investigated using the hot compression test in the temperature range of 700 °C–1100 °C, and strain rate of 0.001 s^?1 to 1 s^?1. The hot tensile test of the alloy was also considered to assist explaining the related deformation mechanism within the same temperature range and the strain rate of 0.1 s^?1. The processing map of the alloy was developed to evaluate the efficiency of hot deformation and to identify the instability regions of the flow. The peak efficiency of 24–28% was achieved at temperature range of 900 °C–1000 °C, and strain rates higher than 0.01 s^?1 in the processing map. The hot ductility and the deformation efficiency of the alloy exhibit almost similar variation with temperature, showing maximum at temperature range of 900 °C–1000 °C and minimum at 700 °C and 1100 °C. Besides, the minimum hot ductility lies in the instability regions of the processing map. The peak efficiency of 28% and microstructural analysis suggests that dynamic recovery (DRV) can occur during hot working of the alloy. At strain rates higher than 0.1 s^?1, the peak efficiency domain shifts from the temperature range of 850 °C–1000 °C to lower temperature range of 800 °C–950 °C which is desirable for hot working of the NiTi alloy. The regions of flow instability have been observed at high Z values and at low temperature of 700 °C and low strain rate of 0.001 s^?1. Further instability region has been found at temperature of 1000 °C and strain rates higher than 1 s^?1 and at temperature of 1100 °C and all range of strain rates.