Evaluation of the method of collecting suspended sediment from large rivers by discharge-weighted pumping and separation by continuous-flow centrifugation

A method for collecting suspended sediment samples has been developed that pumps a discharge-weighted volume of water from fixed depths at four to 40 locations across a river and separates the suspended sediment in the sample using a continuous-flow centrifuge. The efficacy of the method is evaluated by comparing the particle size distributions of sediment collected by the discharge-weighted pumping method with the particle size distributions of sediment collected by depth integration and separated by gravitational settling. The pumping method was found to undersample the suspended sand sized particles (> 63 μm) but to collect a representative sample of the suspended silt and clay sized particles (< 63 μm). The centrifuge separated the silt and clay sized particles (< 63 μm) into three fractions. Based on the average results of processing 17 samples from the Mississippi River and several of its large tributaries in 1990, about 10% of the silt and clay sized material was trapped in a centrifuge bowl-bottom sealing unit containing the nozzle and consisted of mostly medium and coarse silt from 16 to 63 μm. About 74% was retained on a Teflon liner in the centrifuge bowl and consisted of sizes from 0–1 to 63 μm. About 9% was discharged from the centrifuge in the effluent and was finer than 0–1 μm. About 7% was lost during the processes of removing the wet sediment fractions from the centrifuge, drying and weighing. The success of the discharge-weighted pumping method depends on how homogeneously the silt and clay sized particles (< 63 μm) are distributed in the vertical direction in the river. The degree of homogeneity depends on the composition and degree of aggregation of the suspended sediment particles.     

Settling velocity,effective density,and mass composition of suspended sediment in a coastal bottom boundary layer,Gulf of Lions,France

Particle size distribution and size-specific settling velocity are critical parameters for understanding the transport of fine sediment on continental margins. In this study, observed floc size versus settling velocity, volume distributions of particles 2 μm–1 cm in diameter, and calculated effective densities for all particle sizes provided estimates of the mass distribution in suspension, which is used to apportion mass among component particles, microflocs, and macroflocs. Measurements were made during relatively quiescent environmental conditions. Observations of size distributions based on mass demonstrate an increase in the component particle fraction through time. The increase in the percentage of component particles in suspension had implications on water column properties, as small changes in the component particle fraction affected water column optical transmission in a way that was not as easily detected by changes in the volume concentration distribution or total mass concentration. Flocs larger than 133 μm in diameter only comprised one quarter to one third of the mass in suspension. This finding may explain why suspension bulk clearance rates are often an order of magnitude lower than those predicted by other methods.     

Experimental study of the settling of twin spherical particles released side by side: The impact of particle size,fluid viscosity,initial spacing,and particle density

The settling of solid particles in a fluid is an important process that needs to be considered in many fields of research. For example, the interactions among particles and between particles and the surrounding fluid are important topics in studying suspended sediment transport and water clarification. In this paper, the settling processes and interactions of twin spherical particles released side by side were experimentally studied. The Reynolds number varied in the range of 1-300, which is wit...     

Adaptations of microphytobenthos assemblages to sediment type and tidal position

Tagus intertidal microphytobenthos (MPB) assemblages were characterized over a wide range of sediment type and tidal height and the possible effects of these variables on MPB spatial distribution and photo-adaptation mechanisms were investigated. Two transects with six different sediment type and different tidal height sites were sampled once every two months from 2002 to 2004. Upper shore and sandy sites showed higher chlorophyll a (chl a) content, with sandy sediments showing a biomass peak in late winter–early spring, and muddy sites showing no obvious seasonal pattern. Stepwise multiple linear regressions showed that only SiO₂, tidal height and sediment particle size <63 μm were significant variables (p<0.05), explaining 50% of MPB biomass spatial–temporal variability. However, when data were separated by transect, only tidal height remained significant at both transects. Sandier sediments exhibited higher zeaxanthin/chl a and lower fucoxanthin/chl a ratios characteristic of a mixed cyanobacteria/diatom assemblages, showing an alternate seasonality with cyanobacteria increasing in summer and diatoms dominating in spring. Diatom biofilms showed contrasting features depending on the sediment type. Epipsammic diatoms were small with an average length of around 10 μm, while epipelic diatoms showed a wider size range with size distribution peaks at 10–15 μm, 25–35 μm and >60 μm. Epipelic biofilms showed evidence of being low light-acclimated (high fucoxanthin/chl a) and of photo-regulating by vertical migration movements (presence of endogenous vertical rhythms and lower diatoxanthin/diadinoxanthin). Epipsammic biofilms showed higher diatoxanthin/diadinoxanthin ratios and no vertical migration rhythms. Thus, the two diatom biofilm types had distinct strategies to photo-regulate: epipelic diatoms using vertical migration to position themselves at the sediment depth of optimum light conditions, and epipsammic diatoms using the xanthophyll cycle to photo-regulate. Further studies comparing epipsammic and epipelic assemblages are necessary to better understand MPB photo-regulation mechanisms.     

Factors influencing the removal of fine non-cohesive sediment by vortex settling basin at small river abstraction works

Diverted sediment causes a wide range of problems at small diversion works.The difference in water levels between low flows and floods,low investment capital and presence of cohesive sediment and fine non-cohesive sediment coupled with a requirement for a high level of supply assurance makes the design of such hydraulic structures complex.Vortex settling basins(VSBs)offer a promising alternative to conventional settling structures or hydro-cyclones.In the current study,parameters affecting the trapping of particles>75 mm were numerically investigated using ANSYS Fluent and were validated by physical modeling.It was established that the inlet velocity needs to be maintained at 0.26 m/s,the underflow to inflow ratio should be between 0.05 and 0.10,the cylinder height to cylinder diameter ratio should be greater than 0.5,and the positioning of the inlet pipe to cylinder height ratio should be greater than 0.7,with a cone of slope ratio of 2:1(V:H)and the cylinder diameter to inlet diameter ratio should be 8.2.These parameters form the basic design guidelines for VSB use at small diversion works(<100 L/s duty capacity).     

Macroflocs, fine-grained sediment transports, and their longitudinal variations in the Ems Estuary

Field measurements have been carried out to obtain more quantitative knowledge on the longitudinal distribution of the fine-grained sediment dynamics in the Ems Estuary. Both the short-term (time scale < tidal period) and the long-term (tidally averaged) fine-grained sediment transports have been investigated. It is shown that the short-term erosion/sedimentation cycles are most characteristic and are the building blocks for the ultimate long-term transports. Herein, the macroflocs play a key role. The macroflocs had sizes in the range of 200 to 700?μm, sometimes more than 1?mm, and survived high current velocities. The settling velocities were in the range of 0.5 to 8?mm/s. Turbulence intensities and suspended sediment concentration are of utmost importance for the settling properties of the sediment, but the “flocculation ability??of the suspended sediment is shown to be of equal importance. The suspended sediment concentration is only important at low levels of turbulence. At high levels of turbulence, the limiting properties of turbulence dominate. It is demonstrated that the surface properties of the suspended sediment particles are of prime importance for the flocculation ability of the water/sediment mixture, as do the sizes of the resuspended microflocs. Special attention is given to the longitudinal distribution of the sizes and settling properties of the macroflocs as well as of the sediment transports. The flocculation ability was shown to vary almost one order of magnitude along the estuary. These higher flocculation abilities in the direction of higher salinities are responsible for the increase of the sizes of the macroflocs in the seaward direction. Therefore, notwithstanding the low suspended sediment concentrations at the seaward boundary of the Ems Estuary, large macroflocs and corresponding high settling velocities were observed in this area. It explains that, in the Ems Estuary, no distinct effect was determined of the suspended sediment concentration on the settling properties of the suspended macroflocs.     

Effects of grain size on quartz ESR dating of Ti–Li center in fluvial and lacustrine sediments

The electron spin resonance (ESR) dating method has been introduced into the Quaternary chronology for nearly 40 years and has been successfully used for dating of fluvial and lacustrine sediments. In order to evaluate the possible effect of the sediment grain size on the dating estimate, the parallel ESR dating testing was carried out on quartz grains of five different size fractions ranging from 50 to 450 μm extracted from the same fluvial and lacustrine sediment collected close to the M/B boundary at the Donggutuo section, Nihewan Basin, China. The results show that equivalent doses and associated ages vary significantly. However the beta irradiation dose rate of the grains with different sizes accounts for only about 6% of the total deviation of the dating results. At the same time, the sensitivity of quartz Ti–Li center was calculated based on the additional irradiation. It shows that the larger grains are more sensitive than the smaller ones, which can leads to higher saturate ESR intensity and less equivalent dose. The variations of the sensitivity of quartz Ti–Li center of the grains with different sizes are responsible for the primary deviation of the dating results. The results also suggest that 100–150 μm grain size fraction would be priority size for the ESR dating of quartz Ti–Li center on fluvial and lacustrine sediments.     

The equivalent dose of different grain size quartz fractions from lakeshore sediments in the arid region of north China

Equivalent dose (D_e) values were measured by using medium aliquots of different grain size quartz fractions of five lakeshore sediments from the arid region of north China. There are two different relationships between D_e values and grain sizes of these five samples. The first relationship is that the D_e values obtained from various grain sizes are in agreement within 1 delta errors. The second relationship is that D_e values are similar to each other for fractions between 125 and 300 μm, while the D_e value of the 63–90 μm fraction is 40～55% smaller than others. For example, the D_e values obtained for sample #3 are 20.15 ± 1.19 Gy, 19.80 ± 0.83 Gy and 20.93 ± 1.06 Gy for fractions of 90–125, 125–150 and 250–300 μm respectively, but are 10.79 ± 0.84 Gy for the 63–90 μm fraction. The second relationship can't be interpreted by previous studies of both dosimetry and heterogeneous bleaching. It is deduced for sample #2, #3 and #6 that fine particles (<90 μm) intruded after the dominant sedimentation. Comparison of OSL ages from different grain size fractions of sample #2 with a radiocarbon age from the same lithologic layer supports that fractions coarser than 125 μm yield more reliable burial ages, while the fraction finer than 90 μm yields underestimated ages for some lakeshore sediments from this arid region.     

The particle size characteristics of fine‐grained channel deposits in the River Exe Basin,Devon, UK

Deposition and storage of fine‐grained (<62·5 μm) sediment in the hyporheic zone of gravel bed rivers frequently represents an important cause of aquatic habitat degradation. The particle size characteristics of such fine‐grained bed sediment (FGBS) exert an important control on its hydrodynamic properties and environmental impact. Traditionally, particle size analysis of FGBS in gravel bed rivers has focused on the absolute size distribution of the chemically dispersed mineral fraction. However, recent work has indicated that in common with fluvial suspended sediment, significant differences may exist between the absolute and the in situ, or effective, particle size composition of FGBS, as a result of the existence of aggregates, or composite particles. In the investigation reported in this paper, sealable bed traps that could be remotely opened to sample sediment deposited during specific storm runoff events and a laser back‐scatter probe were used to quantify the temporal and spatial variability of both the absolute and effective particle size composition of FGBS, and the associated suspended sediment from four gravel bed rivers in the Exe Basin, Devon, UK. The absolute particle size distributions of both the FGBS and suspended sediment evidenced c. >95%<62·5 μm sized primary particles and displayed a seasonal winter–summer fining, while the opposite trend was displayed by the effective particle size distribution of the FGBS and suspended sediment. The effective particle size distributions of both were typically highly aggregated, comprising up to 68%>62·5 μm sized particles. Spatial variation in the effective particle size and aggregation parameters was of secondary importance relative to temporal variation. The effective particle size distribution of the FGBS was consistently coarser and more aggregated than the associated suspended sediment and there was evidence of aggregate break‐up in samples of resuspended bed sediment. The implications of these findings for sediment transport modelling are considered. Copyright © 1999 John Wiley & Sons, Ltd.     

Sediment dispersal and deposition due to sand mining in the coastal waters of Korea

Understanding the impact of marine sand mining operations in a complex coastal environment requires a combined observational and modeling approach. Here, we use field measurements collected during mining operations in Kyunggi Bay, Korea to develop sediment parameters and source conditions for a three-dimensional (3D) sediment transport model built on the Regional Ocean Modeling System (ROMS). The model is run with realistic forcing obtained from a 9 km meteorological model, tides, and river discharges. The resulting vertical and horizontal distributions of sediment show encouraging agreement with the field data, demonstrating markedly different dispersal patterns due largely to the differential settling of the various sand classes. The resulting depositional patterns suggest that only the coarser size classes (500 and 250 μm) particles remain close to the mined site, while finer size classes are widely dispersed. These results suggest that this new methodology of multi-size class, 3D sediment transport modeling is quite promising, and further work is ongoing to include more realistic representation of sediment resuspension processes.     

Comparing grain size distribution of sediment and original soil under raindrop detachment and raindrop-induced and flow transport mechanism

The grain size distribution (GSD) of sediment in comparison with the original soil GSD is discussed under different slopes (5, 15 and 25%) and rainfall intensities (30, 60 and 90 mm h^–1 with respective duration of 30, 15 and 10 min) but identical runoff (15 mm). The sediment quantification was carried out by raindrop-induced flow transport (RIFT) or/and transport by flow (FT) using a rainfall simulator and a 6 × 1 m² erosion plot and a silt loam. The results show a high degree of enrichment for size classes of 2–4 and 4–8 μm and a high degree of depletion for size classes of >63 μm under different slopes and rainfall intensities. In addition, the results show that the experimental enrichment ratio (ER) for particle size <16 μm under different slopes and rainfall intensities was greater than 1, while the ER for particle size >32 μm was less than 1.     

A computational study of the role of particle size standard deviation on the collision frequency in differential settling

The results of a simple computational model for differential settling are presented illustrating the significant role that particle size distribution plays in collision frequency and sedimentation rate of particles in a quiescent environment. The model tracks a large number of particles(order 10~5) with log-normally distributed diameters,as they settle at their Stokes settling velocities.Particle collisions are detected and result in larger particles that fall more rapidly.A number of simplifying assumptions are made in the model in order to avoid empirical correlations for phenomena such as collision efficiency and particle shape.These simplifying assumptions were needed to isolate and quantify the role of the particle size distribution.Simulated concentration profiles indicate that,even in the absence of collisions, the standard deviation(σ_D) of the particle size strongly influences the bulk mass settling rate as,for largerσ_D, more mass is concentrated in larger,faster falling particles.The collision frequency is also a strong function ofσ_D. For a given mass concentration the collision frequency first increases linearly with increasingσ_D as greater variation in particle size leads to greater variation in particle velocity,and shorter times for particles to catch each other.For largerσ_D more mass is concentrated in larger particles,so,for a given mass concentration,there are fewer particles per unit volume,increasing the mean distance between the particles and reducing the collision frequency.The implications of these results for sedimentation measurement using optical attenuation techniques are discussed.     

Biofilm effects on size gradation,drag coefficient and settling velocity of sediment particles

Sediment particles are often colonized by biofilm in a natural aquatic ecological system, especially in eutrophic water body. A series of laboratory experiments on particle size gradation, drag coefficient and settling velocity were conducted after natural sediment was colonized by biofilm for 5, 10, 15 and 20 days. Particle image acquisition, particle tracking techniques of Particle Image Velocimetry and Particle Tracking Velocimetry were utilized to analyze the changes of these properties. The experimental results indicate that the size gradation, the drag force exerted on bio-particles, and the settling velocity of bio-particles underwent significant change due to the growth of biofilm onto the sediment surface. The study proposes a characteristic particle size formula and a bio-particle settling velocity formula based on the regression of experiment results, that the settling velocity is only 50% to 60% as the single particle which has the same diameter and density. However, biofilm growth causes large particle which the settling velocities are approximately 10 times larger than that of primary particles. These results may be specifically used in the low energy reservoir or lake environment.     

OSL dating of fine and coarse quartz from a Palaeolithic sequence on the Bistrița Valley (Northeastern Romania)

Previous works focused on optically stimulated luminescence dating of quartz extracted from Romanian and Serbian loess reported significant discrepancies between ages obtained on fine (4–11 μm) and coarse (63–90 μm) quartz. The present study is directed at expanding these investigations. The SAR-OSL and double SAR-OSL protocols are applied on quartz of different grain sizes belonging to 9 samples extracted from a newly identified archaeological site at Bistricioara-Lutărie III on the Bistrița Valley (NE Romania). Radiocarbon ages are also obtained for the 3 uppermost cultural layers hosted in the loess-like deposit.Discrepant ages are obtained between fine (4–11 μm) and coarse (63–90 and 90–200 μm, respectively) quartz for equivalent doses higher than ∼80–100 Gy. However, a very good agreement is achieved for the youngest sample, with an age of ∼8 ka (with a D_e of 38 Gy for fine and 35 Gy for coarse grains, respectively). The comparison with independent control provided by radiocarbon dating suggests better agreement of ages calculated for coarse quartz. Our results are once again proof that concerns should be raised regarding the reliability of the equivalent doses obtained on quartz samples for which the laboratory dose response cannot be fitted by a single saturating exponential function. Further systematic investigations are required regarding the very different saturation characteristics of fine and coarse grained quartz.     

Remote sensing of temporal and spatial patterns of suspended particle size in the Irish Sea in relation to the Kolmogorov microscale

Suspended sediments form an integral part of shelf sea systems, determining light penetration for primary production through turbidity and dispersion of pollutants by adsorption and settling of particles. The settling speed of suspended particles depends on their size and on turbulence. Here a method of determining particle size via remote sensing measurements of ocean colour and brightness has been applied to a set of monthly satellite images of the Irish Sea covering a full year (2006). The suspended sediment concentration was calculated from the ratio between green (555 nm) and red (665 nm) wavelengths in MODIS imagery. Empirical formulae were employed to convert suspended sediment concentrations and irradiance reflectance in the red part of the spectrum into specific scattering by mineral particles and floc size. A geographical pattern was evident in all images with shallow areas with fast currents having high year-average suspended sediment concentrations (7.6 mg l⁻¹), high specific scattering (0.225 m² g⁻¹) and thus small particle sizes (143 μm). The reverse is true for deeper areas with slower currents, e.g. the Gyre southwest of the Isle of Man where turbidity levels are lower (3.3 mg l⁻¹), specific scattering is lower (0.081 m² g⁻¹) and thus particle sizes are larger (595 μm) on average over a year. Temporal signals are also seen over the year in these parameters with minimum seasonal amplitudes (a factor 3.5) in the Turbidity Maximum and maximum seasonal amplitudes twice as large (a factor 7) in the Gyre. In the Gyre heating overcomes mixing in summer and stratification occurs allowing suspended sediments to settle out and flocs to grow large. The size of aggregated flocs is theoretically proportional to the Kolmogorov scale. This scale was calculated using depth, current, and wind speed data and compared to the size of flocculated particles. The proportionality changes through the year, indicating the influence of biological processes in summer in promoting larger flocs.     

An idealized model study of flocculation on sediment trapping in an estuarine turbidity maximum

Flocculation has an important impact on particle trapping in estuarine turbidity maximum (ETM) through associated increases in particle settling velocity. To quantify the importance of the flocculation processes, a size-resolved flocculation model is implemented into an ocean circulation model to simulate fine-grained particle trapping in an ETM. The model resolves the particle size from robust small flocs, about 30 μm, to very large flocs, over 1000 μm. An idealized two-dimensional model study is performed to simulate along-channel variations of suspended sediment concentrations driven by gravitational circulation and tidal currents. The results indicate that the flocculation processes play a key role in generating strong tidal asymmetrical variations in suspended sediment concentration and particle trapping. Comparison with observations suggests that the flocculation model produces realistic characteristics of an ETM.     

Evaluation of a laser‐assisted particle sizing/settling velocity determination technique

The use of predictive models for the understanding and management of sediment and contaminant transport generally requires knowledge of particle size and settling velocity. Particle size is often obtained by direct measurements, and the settling velocities are usually predicted using the Stokes' law (or a modification thereof) for single‐grained spherical particles. Such measurements and estimates are not satisfactory measures for cohesive sediments, which exist as agglomerated particles called flocs and whose behaviour is significantly different from that of the single‐grained particles. Direct measurement of settling velocity and size using optical methods in settling columns has also been employed to improve these predictions; however, the subjectivity in determining which particles are in focus results in unreliable size data. An out‐of‐focus particle will generally possess a larger size than in reality. This paper evaluates a laser‐assisted particle sizing/settling velocity determination technique's ability to eliminate the subjectivity and improve particle‐sizing accuracy during settling column experiments. Although the diffraction of light by the translucent standard beads (used for evaluating the technique's accuracy for determining particle size) posed a problem, the results suggest that this technique has potential for assisting researchers to obtain the most accurate settling particle size data possible. Copyright © 2005 John Wiley & Sons, Ltd.     

Response of suspended sediment particle size distributions to changes in water chemistry at an Andean mountain stream confluence receiving arsenic rich acid drainage

Acid drainage is an important water quality issue in Andean watersheds, affecting the sustainability of urban, agricultural, and industrial activities. Mixing zones receiving acid drainage are critical sites where changes in pH and chemical environment promote the formation and dissolution of iron and aluminum oxy/hydroxides. These particles can significantly change the speciation of toxic metals and metalloids throughout drainage networks via sorption, desorption, and settling processes. However, little is known about the behavior of particle size distributions (PSDs) in streams affected by acid drainage and their relationship to metal speciation. This work studied: (a) the PSDs for a wide range of mixing ratios found at a fluvial confluence affected by acid drainage, and (b) the response of PSDs and arsenic speciation to environmental changes found when the particles approach complete mixing conditions. The confluence between the Azufre River (pH ~ 2, high concentration of dissolved metals) and Caracarani River (pH = 8.6, low concentration of dissolved metals) was used as a representative model for study. Field measurements show a bimodal PSD with modal diameters of ~50 and 300 μm. At shorter distances from the junction, the smaller modes with smaller particle volumes were dominant across the stream cross‐sections. A systematic shift towards larger particle sizes and larger particle volumes occurred downstream. The analysis of laboratory PSDs for Azufre/Caracarani mixing ratios between 0.01 and 0.5 (pH from 6.2 to 2.3) showed a bimodal trend with ~15 and 50 μm characteristic diameters; larger particles formed at pH>4. When particle suspensions were transferred in laboratory experiments from very low pH to full mixing conditions (pH ~ 2.8 and mixing ratio ~ 0.25) particle sizes varied, and the dissolved arsenic concentration decreased. The observed reaction kinetics were slow compared to the time scale of advective transport, creating opportunities for engineered controls for arsenic. This work contributes to a better understanding of the chemical‐hydrodynamic interactions in watersheds affected by mining, and identifying opportunities to improve water quality at points of use.     

Effects of oil dispersants on settling of marine sediment particles and particle-facilitated distribution and transport of oil components

This work investigated effects of three model oil dispersants (Corexit EC9527A, Corexit EC9500A and SPC1000) on settling of fine sediment particles and particle-facilitated distribution and transport of oil components in sediment-seawater systems. All three dispersants enhanced settling of sediment particles. The nonionic surfactants (Tween 80 and Tween 85) play key roles in promoting particle aggregation. Yet, the effects varied with environmental factors (pH, salinity, DOM, and temperature). Strongest dispersant effect was observed at neutral or alkaline pH and in salinity range of 0–3.5 wt%. The presence of water accommodated oil and dispersed oil accelerated settling of the particles. Total petroleum hydrocarbons in the sediment phase were increased from 6.9% to 90.1% in the presence of Corexit EC9527A, and from 11.4% to 86.7% for PAHs. The information is useful for understanding roles of oil dispersants in formation of oil-sediment aggregates and in sediment-facilitated transport of oil and PAHs in marine eco-systems.     

Tributary-junction fans as buffers in the sediment cascade: a multi-decadal study

Alluvial fans at tributary junctions modulate sediment flux through river networks, by buffering the mainstem channel from disturbance in the tributaries. Buffering occurs through the storage (and release) of sediment in fans. Here, we use an extensive historic dataset to characterise the ways in which fan buffering can change as sediment supply varies. In New Zealand's East Coast region, sediment supply and fluvial transport are prolific by global standards. We reconstruct how tributary-junction fans in this region have responded to sediment generated by deforestation and extreme storms. The dynamics of five fans along the Tapuaeroa River are examined for the period 1939–2015. In response to major sediment loading, fans aggraded by up to 12 m and prograded by up to 170 m. Net sediment accumulation ranged from near zero to 1.5×10⁶ m³. Fan size, gradient, sediment storage and buffering were influenced by both upstream and downstream controls. Key upstream (tributary) influences were sediment supply and stream power; downstream (mainstem) influences included distal confinement and, importantly, the nature of fan interaction with the mainstem, which aggraded by up to 6 m. The fans' ability to buffer the Tapuaeroa River from change in the tributaries was largely governed by this downstream interaction: as the mainstem aggraded, it increasingly curtailed fan progradation, thus limiting buffering. Previous studies of tributary-junction fans have related fan morphometry to basin characteristics. However, we find that fan slope and area can vary considerably at decadal, annual or even monthly timescales. Consequently, we suggest that such studies could benefit by examining regional histories of disturbance. © 2019 John Wiley & Sons, Ltd.