Dynamic modeling of DC–DC converters with peak current control in double‐stage photovoltaic grid‐connected inverters

In photovoltaic (PV) double‐stage grid‐connected inverters a high‐frequency DC–DC isolation and voltage step‐up stage is commonly used between the panel and the grid‐connected inverter. This paper is focused on the modeling and control design of DC–DC converters with Peak Current mode Control (PCC) and an external control loop of the PV panel voltage, which works following a voltage reference provided by a maximum power point tracking (MPPT) algorithm. In the proposed overall control structure the output voltage of the DC–DC converter is regulated by the grid‐connected inverter. Therefore, the inverter may be considered as a constant voltage load for the development of the small‐signal model of the DC–DC converter, whereas the PV panel is considered as a negative resistance. The sensitivity of the control loops to variations of the power extracted from the PV panel and of its voltage is studied. The theoretical analysis is corroborated by frequency response measurements on a 230 W experimental inverter working from a single PV panel. The inverter is based on a Flyback DC–DC converter operating in discontinuous conduction mode (DCM) followed by a PWM full‐bridge single‐phase inverter. The time response of the whole system (DC–DC + inverter) is also shown to validate the concept. Copyright © 2011 John Wiley & Sons, Ltd.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

A Five‐Element Multiplex Resonant Full‐Bridge DC‐DC Converter with a Variable Inductive Reactance

A five‐element multiplex resonant (LLCLC) full‐bridge DC‐DC converter controlled by pulse frequency modulation (PFM) is proposed in this paper. The high frequency (HF)‐link resonant DC‐DC converter proposed herein can perform wide‐range output power and voltage regulation with a narrow frequency range due to an antiresonant tank that works effectively as a wide‐range variable inductor. The advantageous characteristics of the antiresonant tank provide overcurrent protection in the case of the short‐circuited load condition as well as in the startup interval. Thus, the technical challenges of a conventional LLC DC‐DC converter can be overcome, and the reliability of the relevant switch‐mode power supplies can be improved. The operating principle of the LLCLC DC‐DC converter is described, after which its performance is evaluated in an experimental setup based on the 2.5 kW prototype. Finally, the feasibility of the proposed DC‐DC converter is discussed from a practical point of view.     

A ZVS‐ZCS phase shift full bridge DC‐DC converter with secondary‐side control for battery charging applications

The output power requirement of battery charging circuits can vary in a wide range, hence making the use of conventional phase shift full bridge DC‐DC converters infeasible because of poor light load efficiency. In this paper, a new ZVS‐ZCS phase shift full bridge topology with secondary‐side active control has been presented for battery charging applications. The proposed circuit uses 2 extra switches in series with the secondary‐side rectifier diodes, operating with phase shift PWM. With the assistance of transformer's magnetizing inductance, the proposed converter maintains zero voltage switching (ZVS) of the primary‐side switches over the entire load range. The secondary‐side switches regulate the output voltage/current and perform zero current switching (ZCS) independent of the amount of load current. The proposed converter exhibits a significantly better light load efficiency as compared with the conventional phase shift full bridge DC‐DC converter. The performance of the proposed converter has been analyzed on a 1‐kW hardware prototype, and experimental results have been included.     

Pulse current regenerative resonant snubber‐assisted two‐switch flyback‐type ZVS PWM DC‐DC converter

In this paper, a two‐switch high‐frequency flyback transformer‐type zero voltage soft‐switching PWM DC‐DC converter using IGBTs is proposed. Effective applications for this power converter can be found in auxiliary power supplies of rolling stock transportation and electric vehicles. This power converter is basically composed of two active power switches and a flyback high‐frequency transformer. In addition to these, two passive lossless snubbers with power regeneration loops for energy recovery, consisting of a three‐winding auxiliary high‐frequency transformer, auxiliary capacitors and diodes are introduced to achieve zero voltage soft switching from light to full load conditions. Furthermore, this power converter has some advantages such as low cost circuit configuration, simple control scheme, and high efficiency. Its operating principle is described and to determine circuit parameters, some practical design considerations are discussed. The effectiveness of the proposed power converter is evaluated and compared with the hard switching PWM DC‐DC converter from an experimental point of view, and the comparative electromagnetic conduction and radiation noise characteristics of both DC‐DC power converter circuits are also depicted. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 152(3): 74–81, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20081     

A new method of damping harmonic resonance at the DC link in a large‐capacity rectifier‐inverter system

This paper proposes a new method of damping harmonic resonance in the DC link of a large‐capacity rectifier‐inverter system, such as in rapid‐transit railways. A voltage‐source PWM converter is connected in series to the DC capacitor of the rectifier through a matching transformer, acting as a damping resistor to the DC capacitor current. No filters are needed to extract harmonic components from the DC capacitor current. This results in a quick response and highly stable damping. The relationship between the control gain of the PWM converter and the required rating is theoretically discussed. We show that the required rating is less than one‐thousandth of that previously proposed. In particular, regenerating the power consumed by the PWM converter is very important because of the large power in practical systems. Normally, an additional PWM inverter is connected to the DC bus of the PWM converter to regenerate the consumed power. The additional inverter regenerates the DC power to the AC source through a transformer. This method, however, makes the damping circuit complex, thus the proposed method for the DC‐link harmonic resonance is less practicable. In this paper, a simple and novel scheme that utilizes the DC‐link voltage of the rectifier as a DC source for the PWM converter is proposed. The excellent practicability of the proposed damping method with the novel regenerating scheme is confirmed using digital computer simulation. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 144(2): 53–62, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10172     

A soft‐switching high step‐up DC‐DC converter with a single magnetic component

A soft‐switching high step‐up DC‐DC converter with a single magnetic component is presented in this paper. The proposed converter can provide high voltage gain with a relatively low turn ratio of a transformer. Voltage doubler structure is selected for the output stage. Due to this structure, the voltage gain can be increased, and the voltage stresses of output diodes are clamped as the output voltage. Moreover, the output diode currents are controlled by a leakage inductance of a transformer, and the reverse‐recovery loss of the output diodes is significantly reduced. Two power switches in the proposed converter can operate with soft‐switching due to the reflected secondary current. The voltages across the power switches are confined to the clamping capacitor voltage. Steady‐state analysis, simulation, and experimental results for the proposed converter are presented to validate the feasibility and the performance of the proposed converter. Copyright © 2012 John Wiley & Sons, Ltd.     

A novel prototype of auxiliary edge resonant bridge leg link snubber‐assisted soft‐switching sine‐wave PWM inverter

This paper proposes a new circuit topology of the three‐phase soft‐switching PWM inverter and PFC converter using IGBT power modules, which has the improved active auxiliary switch and edge resonant bridge leg‐commutation‐link soft‐switching snubber circuit with pulse current regenerative feedback loop as compared with the typical auxiliary resonant pole snubber discussed previously. This three‐phase soft‐switching PWM double converter is more suitable and acceptable for a large‐capacity uninterruptible power supply, PFC converter, utility‐interactive bidirectional converter, and so forth. In this paper, the soft‐switching operation and optimum circuit design of the novel type active auxiliary edge resonant bridge leg commutation link snubber treated here are described for high‐power applications. Both the main active power switches and the auxiliary active power switches achieve soft switching under the principles of ZVS or ZCS in this three‐phase inverter switching. This three‐phase soft‐switching commutation scheme can effectively minimize the switching surge‐related electromagnetic noise and the switching power losses of the power semiconductor devices; IGBTs and modules used here. This three‐phase inverter and rectifier coupled double converter system does not need any sensing circuit and its peripheral logic control circuits to detect the voltage or the current and does not require any unwanted chemical electrolytic capacitor to make the neutral point of the DC power supply voltage source. The performances of this power conditioner are proved on the basis of the experimental and simulation results. Because the power semiconductor switches (IGBT module packages) have a trade‐off relation in the switching fall time and tail current interval characteristics as well as the conductive saturation voltage characteristics, this three‐phase soft‐switching PWM double converter can improve actual efficiency in the output power ranges with a trench gate controlled MOS power semiconductor device which is much improved regarding low saturation voltage. The effectiveness of this is verified from a practical point of view. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 64–76, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20207     

Dynamic modeling of a dual active bridge DC to DC converter with average current control and load‐current feed‐forward

Bidirectional power flow is needed in many power conversion systems like energy storage systems, regeneration systems, power converters for improvement of the power quality and some DC‐DC applications where bidirectional high power conversion and galvanic isolation are required. The dual active bridge (DAB) is an isolated, high voltage ratio DC‐DC converter suitable for high power density and high power applications, being a key interface between renewable energy sources and energy storage devices. This paper is focused on the modeling and control design of a DC‐DC system with battery storage based on a DAB converter with average current mode control of the output current and output voltage control. The dynamic response of the output voltage to load steps is improved by means of an additional load‐current feed‐forward control loop. An analytical study of the load‐current feed‐forward is presented and validated by means of both simulations and experimental results. Copyright © 2014 John Wiley & Sons, Ltd.     

Series resonant high‐voltage DC–DC converter with reduced component count

This paper proposes a novel zero‐current‐switching series resonant high‐voltage DC–DC converter with reduced component count. The series resonant inverter in the proposed topology has two power switches (insulated‐gate bipolar transistors, IGBTs), two resonant capacitors, and only one high‐voltage transformer (HVT) with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. The leakage inductances of the transformer's primary windings together with the resonant capacitors form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with interleaved half switching cycle. The secondary winding of the HVT is connected to a bridge rectifier circuit to rectify the secondary voltage. The converter operates in the discontinuous conduction mode (DCM) and its output voltage is regulated by pulse frequency modulation. Therefore, all the power switches turn on and off at the zero‐current switching condition. The main features of the proposed converter are its lower core loss, lower cost, and smaller size compared to previously proposed double series resonant high voltage DC–DC converters. The experimental results of a 130‐W prototype of the proposed converter are presented. The results confirm the excellent operation and performance of the converter. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Design and implementation of a high‐efficiency bidirectional DC‐DC Converter for DC micro‐grid system applications

This paper studies the design and implementation of a non‐isolated dual‐half‐bridge bidirectional DC‐DC converter for DC micro‐grid system applications. High efficiency can be achieved under wide‐range load variations by the zero‐voltage‐switching features and an adaptive phase‐shift control method. A three‐stage charging scheme is designed to meet the fast‐charging demand and prolong the lifetime of LiFePO₄ batteries. A digital‐signal‐processing control IC is used to realize the power flow control, DC‐bus voltage regulation, and battery charging/ discharging of the studied bidirectional DC‐DC converter. Finally, a 10 kW prototype converter with Enhanced Controller Area Network communication function is built and tested for micro‐grid system applications. A light‐load efficiency over 96% and a rated‐load efficiency over 98% can be achieved. Copyright © 2013 John Wiley & Sons, Ltd.     

One‐cycle controlled quadratic buck converter

The quadratic DC‐DC converter can broaden the voltage conversion ratio, which meets the requirements of wide input voltage. However, large‐scale variation of input voltage puts forward harsh requirements on ability to resist input disturbance of control strategy. Quadratic buck converter (QBC) is pulsed nonlinear dynamic systems, so the one‐cycle control strategy based on robustness principle may provide better rejection of power source than the linear feedback control. But the traditional one‐cycle controlled QBC (TOCCQBC) suffers from poor ability against load disturbance and steady‐state error. To overcome aforementioned shortages, an improved OCCQBC is proposed by adding inductor current to diode voltage as integral variable and introducing feedback of output voltage. The paper first introduces the working principle of the QBC, and second, the OCCQBC is presented. Then, a mathematical model using small signal analysis of the OCCQBC is established, and an experimental prototype with a power of 6 W is set up. Simulation and experimental results verify the correctness of the theoretical analysis and the feasibility of the strategy.     

Fast‐transient DC‐DC converter using a high‐performance error amplifier with a rapid output‐voltage control technique

This letter presents a method for improving the transient response of DC‐DC converters. The proposed technique replaces the conventional error amplifier with a combination of two different amplifiers to achieve a high loop gain and high slew rate. In addition, a rapid output‐voltage control circuit is employed to further reduce the recovery time. The proposed technique was applied to a four‐phase buck converter, and the chip was implemented using a 0.18‐μm CMOS process. The switching frequency of each phase was set at 2 MHz. Using a supply voltage of 2.7–5.5 V and an output voltage of 0.6–1.5 V, the regulator provided up to 2‐A load current with maximum measured recovery time of only 6.2 and 6.5 μs for increasing and decreasing load current, respectively. Copyright © 2017 John Wiley & Sons, Ltd.     

Improved control‐to‐output characteristics of a PWM buck‐boost converter

An indirect control variable for improving the control‐to‐output characteristics of a Pulse Width Modulation (PWM) buck‐boost converter is introduced in this letter. The voltage gain and the small‐signal model of the buck‐boost converter are reviewed. The actual voltage command at one input of the PWM comparator is from the proposed indirect control variable and the peak value of the high‐frequency PWM carrier. The resulted voltage gain function appears proportional to this indirect control command. Also the dependence of the DC gain of the control‐to‐output transfer function on the duty cycle is eliminated. Experimental results conform well to the theoretical analysis. Copyright © 2010 John Wiley & Sons, Ltd.     

Characteristics comparison of high‐frequency multilevel inverter connected with filter inverters

This paper presents a characteristics comparison of a high‐frequency multilevel inverter connected with small‐ capacity filter inverters. In general, PWM inverters require a low‐pass filter in order to reduce switching harmonics. However, in the high‐frequency systems such as class D power amplifiers, the cutoff frequency of the low‐pass filter must be set at high frequency. Thus, harmonic distortion of the output voltage is enlarged to a harmful level. Increasing the number of output voltage levels is effective in reducing the harmonic distortion of the output voltage and the low‐pass filter size. The proposed systems consist of a five‐level inverter and several cascade‐connected low‐voltage full bridge inverters without any external DC power sources for filtering the output voltage. The five‐level inverter generates a stepwise waveform with five‐level voltage, and the low‐voltage filter inverter superimposes harmonic components to compensate for the voltage waveform distortion. Therefore, the proposed system can reduce its total switching loss and can increase the number of the output voltage levels. In this paper, the effectiveness of the proposed systems is verified through several experiments. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 161(3): 58–65, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20373     

A systematic approach to designing a wide‐current range,MOS capacitor‐based switched‐capacitor DC‐DC converter with an augmenting LDO

Switched‐capacitor DC‐DC converters (SC DC‐DC) are analyzed for loss sources, voltage regulation integrity, start‐up latency, and ripple size, while the trade‐offs between these metrics are derived. These analyses are used to design a SC DC‐DC that achieves high efficiency in a wide load current range. Four‐way interleaving was employed to reduce the output ripple and efficiency loss due to this ripple. The design can be reconfigured to achieve gains of 1/3 and 2/5 for inputs ranging between 1.4 and 3.6 V to generate output voltage range of 0.4 to 1.27 V and can supply peak load current of 22 mA. It uses thin‐oxide MOS capacitors for their high density and achieves 75.4% peak efficiency with an input frequency of 100 MHz and a load capacitor of 10 nF. An augmenting LDO that only regulates during sudden load transients helps the converter respond fast to these transients. The chip was implemented using a 65‐nm standard CMOS process.     

A step‐up PWM DC–DC converter for renewable energy applications

A step‐up pulse width modulation (PWM) direct current (DC)–DC converter is presented in this paper, which has its origin in quasi Z‐source inverter. Analysis of this converter in steady state is presented, and relevant expressions are derived for the proposed converter operating in continuous conduction mode. The power loss expressions for each component of the converter are derived, and thereby, obtained expressions for overall converter efficiency are presented. Further, a dynamic model is derived to design an appropriate controller for this converter. The simulation and experimental results are presented to support the theoretical analysis. The advantages such as continuous input current, high step‐up gain at lower duty ratio, and common ground for source, load, and switch makes the converter suitable for renewable energy applications. Copyright © 2015 John Wiley & Sons, Ltd.     

A single‐stage phase‐shifted full‐bridge AC/DC converter with variable frequency control

This letter presents a single‐stage soft‐switched full‐bridge AC/DC converter for low‐voltage/high‐current output applications. A phase‐shifted method with a variable frequency control is used to regulate the DC bus voltage and the output voltage of the single‐stage AC/DC converter. The proposed circuit topology and control scheme exhibit superior performances (i.e. high power factor, high‐efficiency, and ring‐free features). Correspondingly, a laboratory prototype, 500 W 5V/100A AC/DC converter, is implemented to verify the feasibility of the proposed design. Copyright © 2009 John Wiley & Sons, Ltd.     

创新型的基于软开关的X射线电源系统

自动X射线检测(AXI)已经成为检测和评估复杂微机电系统(MEMS)和微光电子机械系统(MOEMS)的基本方法,在医疗、考古等领域也有了广泛应用,而稳定可靠高效的直流高压电源是AXI的核心组件。一般的高压直流电源为定值输出,它们在X射线管这样的宽负载变化范围下的稳态和暂态响应不能满足AXI的要求。基于AXI的需要,本文介绍了一种最新研制的可调高压电源,创新型的主电路拓扑结构由PFC(功率因数校正)模块、Buck模块、逆变电路、高频变压器和倍压电路组成。电源利用变压器的寄生参数谐振工作,利用软形状技术实现了ZCS低损耗。PFC模块能使此电源系统适用于国内外市场并且可减小对电网的谐波污染。电源的控制电路采用基于DSP的PI调解器,并基于RS232实现与PC的通信,从而实现本地控制和远程管理。     

Analysis and implementation of a high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter

A high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter with ripple‐free input current is presented. In the presented converter, the ripple‐free boost cell provides ripple‐free input current and zero‐voltage switching of power switches. The resonant flyback cell provides zero‐voltage switching of power switches and zero‐current switching of the output diode. Also, it has a simple output stage. The proposed converter achieves high efficiency because of the reduction of the switching losses of the power switches and the output diode. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed and its experimental results are presented for validation. Copyright © 2011 John Wiley & Sons, Ltd.