A Novel Packaging Film from Cassava Starch and Natural Rubber

Currently, there is an environmental pollution problem generated in part by packaging materials produced from non-biodegradable synthetic polymers made from petroleum. However, these can be replaced with biodegradable materials made from cassava starch (CS) and natural rubber (NR). In the work described, a novel biopolymer film was obtained from the CS and NR using glycerol (GE) as a plasticizer in a water-based system. The physical properties of an 95/5 CS/NR blend films with the addition of NR and with varying GE contents were studied based on their swelling ratio, moisture content, moisture absorption, mechanical properties and biodegradability in soil. The results showed that the moisture content and moisture absorption tended to be directly proportional to the GE content, while the moisture content and moisture absorption of the sample decreased as a function of the NR content. The swelling ratio of the 95/5 CS/NR blend slightly decreased as a function of the NR and GE content. Surprisingly, the best swelling ratio of 350% was found at 10% NR. The elongation at break of the CS/NR blend was improved by the addition of GE. The contact angle of the 95/5 CS/NR blend decreased as a function of the GE. With increased NR in the composite, an increasing, trend in the contact angle was found. Further, the 95/5 CS/NR blend exhibited good transparency when it was applied as a coating to delay the ripening of bananas, the results were positive. Moreover, the film showed decomposition well in natural soil.     

Utilization of Porous Carbons Derived from Coconut Shell and Wood in Natural Rubber

The porous carbons derived from cellulose are renewable and environmentally friendly. Coconut shell and wood derived porous carbons were characterized with elemental analysis, ash content, X-ray diffraction, infrared absorbance, particle size, surface area, and pore volume. The results were compared with carbon black. Uniaxial deformation of natural rubber (NR) composites indicate the composites reinforced with the porous carbon from coconut shell have higher tensile moduli at the same elongation ratio than the composites reinforced with wood carbon. 40 % coconut shell composite showed a fivefold increase in tensile modulus compared to NR. Polymer–filler interactions were studied with frequency dependent shear modulus, swelling experiments and dynamic strain sweep experiments. Both linear and non-linear viscoelastic properties indicate the polymer–filler interactions are similar between coconut shell carbon and wood carbon reinforced composites. The swelling experiments, however, showed that the polymer–filler interaction is greater in the composites reinforced with coconut shell instead of wood carbon.     

Comparison of Polylactic Acid/Kenaf and Polylactic Acid/Rise Husk Composites: The Influence of the Natural Fibers on the Mechanical, Thermal and Biodegradability Properties

This paper investigates and compares the performances of polylactic acid (PLA)/kenaf (PLA-K) and PLA/rice husk (PLA-RH) composites in terms of biodegradability, mechanical and thermal properties. Composites with natural fiber weight content of 20% with fiber sizes of less than 100 μm were produced for testing and characterization. A twin-screw extrusion was used to compound PLA and natural fibers, and extruded composites were injection molded to test samples. Flexural and Izod impact test, TGA, soil burial test and SEM were used to investigate properties. All results were compared to a pure PLA matrix sample. The flexural modulus of the PLA increased with the addition of natural fibers, while the flexural strength decreased. The highest impact strength (34 J m⁻¹), flexural modulus (4.5 GPa) and flexural strength (90 MPa) were obtained for the composite made of PLA/kenaf (PLA-K), which means kenaf natural fibers are potential to be used as an alternative filler to enhance mechanical properties. On the other hand PLA-RH composite exhibits lower mechanical properties. The impact strength of PLA has decreased when filled with natural fibers; this decrease is more pronounced in the PLA-RH composite. In terms of thermal stability it has been found that the addition of natural fibers decreased the thermal stability of virgin PLA and the decrement was more prominent in the PLA-RH composite. Biodegradability of the composites slightly increased and reached 1.2 and 0.8% for PLA-K and PLA-RH respectively for a period of 90 days. SEM micrographs showed poor interfacial between the polymer matrix and natural fibers.     

Mechanical Properties of Poly (Lactic Acid)/Hemp Fiber Composites Prepared with a Novel Method

This research dealt with a novel method of fabricating green composites with biodegradable poly (lactic acid) (PLA) and natural hemp fiber. The new preparation method was that hemp fibers were firstly blending-spun with a small amount of PLA fibers to form compound fiber pellets, and then the traditional twin-screw extruding and injection-molding method were applied for preparing the composites containing 10–40 wt% hemp fibers with PLA pellets and compound fiber pellets. This method was very effective to control the feeding and dispersing of fibers uniformly in the matrix thus much powerful for improving the mechanical properties. The tensile strength and modulus were improved by 39 and 92 %, respectively without a significant decrease in elongation at break, and the corresponding flexural strength and modulus of composites were also improved by 62 and 90 %, respectively, when the hemp fiber content was 40 wt%. The impact strength of composite with 20 wt% hemp fiber was improved nearly 68 % compared with the neat PLA. The application of the silane coupling agent promoted further the mechanical properties of composites attributed to the improvement of interaction between fiber and resin matrix.     

Effect of Nanoscale SiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript> as the Fillers on the Mechanical Properties and Aging Behavior of Linear Low-Density Polyethylene/Low-Density Polyethylene Blends

Linear low-density polyethylene (LLDPE) was blended with low-density polyethylene (LDPE) at a fixed ratio (80 wt LLDPE and 20 wt %LDPE) and filled with nanoparticles of SiO₂ and TiO₂ at a ratio up to wt 5%, so as to develop the polymeric composites suitable to preparing the agricultural micro-irrigation pipes having good environmental adaptability. These compounds were blended using calcium stearate, polyethylene wax, and titanate coupling agent as the auxiliary dispersants, and ethylene-vinyl acetate copolymer (EVA) as the toughness improver. The LLDPE/LDPE composites filled with the nanoparticles were extruded and injected to prepare the composites specimens for the performance evaluations and micro-irrigation pipe field test. The mechanical properties, thermostability, and processibility of the injected composites were investigated. The effect of heating in an oven and irradiating by ultraviolet on the mechanical properties of the composites was explored. The environmental adaptability of the micro-irrigation pipes made of the filled LLDPE/LDPE composites was evaluated making use of long-term outdoor field test in northwest China where the arid and harsh natural conditions are of great concerns. It was found that the LLDPE/LDPE blend with the LLDPE mass fraction fixed as 80% showed balanced mechanical and thermal properties and flexibility, and was suitable to be used as the basic resin matrix. The incorporation of nano-TiO₂ contributed to effectively improving the resistance to heating and ultraviolet irradiation of the composites. The composite made from 91% basic resin matrix, 6% EVA, and 3% mixed nano-SiO₂ and TiO₂, showed balanced comprehensive properties. The micro-irrigation pipes made of this filled LLDPE/LDPE composite had good environmental adaptability and service behavior in a three-year field test and were suitable to be used in arid area.     

The Effect of Fiber Pretreatment and Compatibilizer on Mechanical and Physical Properties of Flax Fiber-Polypropylene Composites

Recently, investigations have been conducted on the use of natural fibers as reinforcement in low-melting point thermoplastics to improve mechanical properties of composites. However, due to some limitations of natural fibers, composite formulation and processing parameters must be controlled to produce a product with improved properties. This study was conducted to investigate the influence of flax fiber loading, use of compatibilizer and pretreatment on physical and mechanical properties of compression-molded composite. In this study, untreated and treated (sodium hydroxide-treated and mild-bleached flax fibers) fibers at 15% and 30% of the total product mass were used in formulations. To investigate the effect of compatibilizer on product properties, maleic anhydride grafted polypropylene (MAPP) was added at 5% by mass in the formulations. After extrusion of composites formulations, they were formed using compression molding. Results indicated that using flax fiber in composites without pretreatment and compatibilizer could result into products with inferior physical and mechanical properties; this could be compensated by the use of a compatibilizer. However, the use of compatibilizer had some negative effects on some other physical properties like color and melt flow index (MFI).     

A Comparison Study of Wheat Gluten Composites Filled with Dialdehyde Starch and Native Starch

Environmentally friendly green composites were prepared by blending Wheat gluten (WG) as matrix, dialdehyde starch (DAS) as filler and glycerol as plasticizer followed by compression molding of the mixture at 110 °C. The properties of the WG/DAS composite are compared with those of the WG/native wheat starch (NWS) composites. While tensile strength and strain at break decrease with increasing NWS content in the WG/NWS composites, a small content of DAS could improve tensile strength and strain at break simultaneously in the WG/DAS composites. The WG/DAS composites exhibit reduced moisture absorption in comparison with the WG/NEW composites. Formation of chemical bonding between DAS and WG is beneficial for the dispersion of DAS in the WG matrix and WG/DAS composites exhibit improved mechanical properties and reduced moisture absorption over the WG/NWS composites.     

Synergistic Effect of Oil Palm Based Pozzolanic Materials/Oil Palm Waste on Polyester Hybrid Composite

This research work aims to investigate the synergistic effect of pozzolanic materials such as oil palm ash (OPA) and oil palm empty fruit bunch (OPEFB) on the developed hybrid polymer composites. The OPEFB and OPA fillers of different particle sizes (250, 150, and 75 µm) were mixed at OPEFB:OPA ratios of (0:100; 20:80; 40:60; 60:40; 80:20 and 100:0) and incorporated into an unsaturated polyester resin. Furthermore, both mechanical and morphological properties of the composites were analyzed and it was found that tensile, flexural, and impact properties were significantly improved at OPEFB:OPA of 75 µm particle size hybridization of the polymer. The increase of OPEFB to OPA filler ratio up to 80:20 significantly improved the tensile properties of the composites while 40:60 ratio of 75 µm gave the optimum filler ratio to obtain the highest flexural and impact properties of the composites among all studied samples. Scanning electron micrograph images showed strong particle dispersion of the embedded fillers with resin which explained the excellent mechanical strength enhancement of the composite.     

Biomass Carbon Ratio of Polymer Composites Measured by Accelerator Mass Spectrometry

The evaluation method of biomass carbon ratio of polymer composite samples including organic and inorganic carbons individually was investigated. Biodegradable plastics and biobased plastics can have their mechanical properties improved by combining with inorganic fillers. Polymer composites consisting of biodegradable plastics and carbonate were prepared by two different methods. Poly(lactic acid) (PLA) composite was prepared by synthesis from l-lactide with catalyst and calcium carbonate (CaCO₃) powders from lime. Poly(butylene succinate) (PBS) composite was prepared by hot-pressing the mixture of PBS powder and CaCO₃ powders from oyster shells. The mechanical properties of composite samples were investigated by a tensile test and a compression test using an Instron type mechanical tester. Tensile test with a dumbbell shape specimen was performed for PBS composite samples and compression test with a column shape specimen for PLA composite samples. Strength, elastic modulus and fracture strain were obtained from the above tests. Biomass carbon ratio is regulated in the American Standards for Testing and Materials (ASTM). In ASTM standards on biomass carbon ratio, it is required that carbon atoms from carbonates, such as CaCO₃, are omitted. Biomass carbon ratio was evaluated by ratio of ¹⁴C to ¹²C in the samples using Accelerator Mass Spectrometry (AMS). The effect of pretreatment, such as oxidation temperature and reaction by acid, on results of biomass carbon ratio was investigated. Mechanical properties decrease with increasing CaCO₃ content. The possibility of an evaluation method of biomass carbon ratio of materials including organic and inorganic carbons was shown.     

Single-Plant Biocomposite from Ricinus Communis: Preparation, Properties and Environmental Performance

A single-plant biobased composite material was prepared from fibre and matrix constituents produced from the castor plant, ricinus communis. It is shown that the mechanical properties of the castor plant fibres are comparable to those of other bast fibres and that the stiffness and strength characteristics of the castor fibre/polyamide 11 biocomposite compare well with those of other natural fibre composites. By using a biobased thermoplastic matrix material the reliance on non-renewable feedstock sources is reduced and end-of-lifetime recyclability is improved. The analysis of the environmental performance of the new castor plant composite suggests that the biobased material has great potential as a sustainable alternative replacing glass fibre-reinforced plastics.     

Potential Use of Recycled PET in Comparison with Liquid Crystalline Polyester as a Dual Functional Additive for Enhancing Heat Stability and Reinforcement for High Density Polyethylene Composite Fibers

The recycle poly(ethylene terephthalate) (rPET) used as an alternative reinforcing material for in situ microfibrillar-reinforced composite, compared with liquid crystalline polymer (LCP), was investigated. The PE-LCP and PE-rPET composites were prepared as fiber using hot drawing process. The effects of draw ratios and compatibilizer (styrene-ethylene butylene-styrene-grafted maleic anhydride, SEBS-g-MA) loading on morphology, tensile properties, thermal stability and dynamic mechanical characteristics of the LCP- and rPET-composite systems were studied. In as-spun samples containing compatibilizer, the fibrillation of LCP domains was observed whereas rPET domains appeared as droplets. After drawing, good fibrillation of LCP and rPET domains is remarkably observed especially in the composite fibers with compatibilizer loading. The mechanical properties of the composite fibers were strongly depended on the fibrillation of the dispersed phases which directly related the levels of draw ratio and compatibilizer loading. The mechanical properties enhanced by SEBS-g-MA were more pronounced in the rPET than LCP systems. The presence of rPET in the composite fibers alone or with the compatibilizer clearly improved the thermal resistance of PE whereas no significant change in thermal stability for the LCP-containing composite fibers with and without compatibilizer loading. The results from dynamic mechanical analysis revealed that an improvement in dynamic mechanical properties of the composite fibers could be achieved by drawing with optimum draw ratio together with optimum compatibilizer dosage. All obtained results suggested the high potential of rPET minor blend-component as a good reinforcing and thermal resistant materials for the thermoplastic composite fiber, in replacing the more expensive LCP.     

Sustainable Use of Coffee Husks For Reinforcing Polyethylene Composites

The utilization of the coffee husk fiber (CHF) from the coffee industry as a reinforcing filler in the preparation of a cost-effective thermoplastic based composite was explored in this study. The chemical composition and thermal properties of the CHF were investigated and compared with those of wood fiber (WF). CHF proved to be mainly composed of cellulose, hemicellulose and lignin, and exhibited similar thermal behavior to WF. High density polyethylene (HDPE) composites with CHF loadings of from 40 to 70% were prepared using melt processing and extrusion. The processing properties, mechanical behavior, water absorption and thermal performance of these composites were investigated. The effect of maleated polyethylene (MAPE) used as a coupling agent on the composite was explored. The experimental results showed that increasing the CHF loading in the HDPE matrix resulted in an increase in the modulus and thermal properties of the composites, but resulted in poor water resistance. The addition of a 4% MAPE significantly improved the interfacial behavior of the hydrophilic lignocellulosic fiber and the hydrophobic polymer matrix.     

Preliminary Study of Non-woven Composite: Effect of Needle Punching and Kenaf Fiber Loadings on Non-woven Thermoplastic Composites Prepared From Kenaf and Polypropylene Fiber

Non-woven composites were produced using kenaf (bast) fiber and polypropylene (PP) fiber. The effects of needle punching process, number of needle and kenaf fiber loadings on the properties of non-woven composite were studied. The aspect ratio of kenaf fiber was also measured in this study. The aspect ratio of most of kenaf fiber used was in the range of 200–400. The results indicated that the mechanical strength of the non-woven composite was significantly influenced by the percentage of kenaf fiber. This may due to the evenly mixed kenaf and PP fibers during carding process prior to the mechanical interlocking by needle punching process. The tensile strength, modulus and toughness were enhanced with the incorporation of carded and needle punched fibers. The number of needle used in needle punching process had a significant effect on the strength of the composite. This was evident in SEM micrograph where composite prepared from carded to needle punched non-woven web showed better wettability as compared to composite prepared from carded non-woven web only. However, no significant difference was observed in water absorption and thickness swelling tests for composites prepared with different number of needles.     

Study on the Effect of Dicumyl Peroxide on Structure and Properties of Poly(Lactic Acid)/Natural Rubber Blend

In attempt to enhance the compatibility of NR in PLA matrix, and furthermore to enhance mechanical properties of PLA, PLA/NR blends with strong interaction were prepared in Haake internal mixer, using dicumyl peroxide (DCP) as cross-linker. The effects of dicumyl peroxide on morphology, thermal properties, mechanical properties and rheological properties of PLA and PLA/NR blends were studied. The results indicated that dicumyl peroxide could increase the compatibility of poly(lactic acid) and natural rubber. With small amount of dicumyl peroxide, the effect on NR toughening PLA was enhanced and the tensile toughness of PLA/NR blends was improved. When the DCP content was up to 0.2 wt%, the PLA/NR blend reached the maximum elongation at break (26.21 %) which was 2.5 times of that of neat PLA (the elongation at break of neat PLA was 10.7 %). Meanwhile, with introducing 2 wt% DCP into PLA/NR blend, the maximum Charpy impact strength (7.36 kJ/m²) could be achieved which was 1.8 times of that of neat PLA (4.18 kJ/m²). Moreover, adding adequate amount of DCP could improve the processing properties of blends: the viscosity of PLA/NR blend decreased significantly and the lowest viscosity of the blends could be achieved when the DCP content was 0.5 wt%.     

Injection Molded Wheat Straw and Corn Stem Filled Polypropylene Composites

Environmentally friendly composite materials can be prepared using wood fibers and/or various types of agro-derived fibers as reinforcements. In this study, agro-residues such as wheat straw and corn stem filled polypropylene were prepared and their suitability was investigated as a reinforcing filler in thermoplastics and as an alternative to the wood flour filled plastics. Effect of compounding techniques, compatibilizer and fungal treatment of agro-residues on the mechanical properties of the composites were evaluated. It was found that high shear compounding of wheat straw fibers exhibited similar properties to that produced by the milled wheat straw. This may be due to the extensive fiber breakage occurred during the high shear compounding that results in a similar aspect ratio to that of milled straw. Compatibilizer is needed for improving the strength properties of the agro-residue filled PP composites. Fungal treatment of milled wheat straw did not show much improvement in the strength properties of the composites. Comparison of mechanical properties of the agro-residue filled PP with that of the wood flour and the old newsprint filled PP showed the suitability of the agro-residues as alternative filler for thermoplastics.     

Preformed Amide-containing biopolymer for Improving the Environmental Performance of Synthesized Urea–formaldehyde in Agro-fiber Composites

Investigations have continued for production high performance agro-based composites using environmentally acceptable approaches. This study examines the role of adding amide-containing biopolymers during synthesis of urea–formaldehyde (UF) on properties of adhesive produced, especially its adhesion potential. The environmental performance of UF-resin synthesized in the presence of modified amide-containing biopolymer was evaluated by evaluating the free-HCHO of both adhesive (during processing) and of the eventual engineered composite product. Also, the benefits of this synthesis-modified adhesive in enhancing the bondability of sugar-cane fibers used in engineered composite panels was evaluated and compared to using UF-resin. The results obtained show that, static bending of the produced composites varied from 27.7 to 33.13 N/mm² of modulus of rupture (MOR) and from 2860 to 3374 N/mm² of Modulus of Elasticity (MOE); while for internal bond (IB) it’s varied from 0.64 to 0.866 N/mm². Based on the ANSI and EN Standards modified UF-based agro composites produced meet the performance requirements for high grade particleboards with respect to static bending strength. These agro-based composite also tested out as having free-HCHO values of ~13 mg/100 g board.     

Chemical Treatments of Natural Fiber for Use in Natural Fiber-Reinforced Composites: A Review

Studies on the use of natural fibers as replacement to man-made fiber in fiber-reinforced composites have increased and opened up further industrial possibilities. Natural fibers have the advantages of low density, low cost, and biodegradability. However, the main disadvantages of natural fibers in composites are the poor compatibility between fiber and matrix and the relative high moisture sorption. Therefore, chemical treatments are considered in modifying the fiber surface properties. In this paper, the different chemical modifications on natural fibers for use in natural fiber-reinforced composites are reviewed. Chemical treatments including alkali, silane, acetylation, benzoylation, acrylation, maleated coupling agents, isocyanates, permanganate and others are discussed. The chemical treatment of fiber aimed at improving the adhesion between the fiber surface and the polymer matrix may not only modify the fiber surface but also increase fiber strength. Water absorption of composites is reduced and their mechanical properties are improved.     

Hybrid Composites from Waste Materials

Hybrid composites of thermoplastic biofiber reinforced with waste newspaper fiber (NF) and poplar wood flour (WF) were prepared. The weight ratio of the lignocellulosic materials to polymer was 30:70 (w:w). Polypropylene (PP) and maleic anhydride grafted polypropylene (MAPP) were also used as the polymer matrix and coupling agent, respectively. The mechanical properties, morphology and thermal properties were investigated. The obtained results showed that tensile and flexural modulus of the composites were significantly enhanced with addition of biofibers in both types (fiber and flour), as compared with pure PP. However, the increasing in WF content substantially reduced the tensile, flexural and impact modulus, but improved the thermal stability. This effect is explained by variations in fiber morphological properties and thermal degradation. Increasing fiber aspect ratio improved mechanical properties. The effect of fiber size on impact was minimal compared to the effects of fiber content. Scanning electron microscopy has shown that the composite, with coupling agent, promotes better fiber–matrix interaction. The largest improvement on the thermal stability of hybrid composites was achieved when WF was added more. In all cases, the degradation temperatures shifted to higher values after addition of MAPP. This work clearly showed that biofiber materials in both forms of fiber and flour could be effectively used as reinforcing elements in thermoplastic PP matrix.     

Biopolymers Based Green Composites: Mechanical, Thermal and Physico-chemical Characterization

Natural cellulosic fibers are one of the smartest materials for use as reinforcement in polymers possessing a number of applications. Keeping in mind the immense advantages of the natural fibers, in present work synthesis of natural cellulosic fibers reinforced polymer composites through compression molding technique have been reported. Scanning Electron microscopy (SEM), Thermo gravimetric/Differential thermal/Derivative Thermogravimetry (TGA/DTA/DTG), absorption in different solvents, moisture absorbance, water uptake and chemical resistance measurements were used as characterization techniques for evaluating the different behaviour of cellulosic natural fibers reinforced polymer composites. Effect of fiber loading on mechanical properties like tensile strength, flexural strength, compressive strength and wear resistances has also been determined. Reinforcing of the polymer matrix with natural fibers was done in the form of short fiber. Present work indicates that green composites can be successfully fabricated with useful mechanical properties. These composites may be used in secondary structural applications in automotive, housing etc.     

Feather Fiber Reinforced Light-Weight Composites with Good Acoustic Properties

Three to four billion pounds of chicken feathers are wasted in the United States annually. These feathers pose an environmental challenge. In order to find a commercial application of these otherwise wasted feathers, composites have been prepared from feathers. Flexural, impact resistance, and sound dampening properties of composites from chicken feather fiber (FF) and High Density Polyethylene/Polypropylene (HDPE/PP) fiber have been investigated and compared with pulverized chicken quill-HDPE/PP, and jute-HDPE/PP composites. Sound dampening by FF composites was 125% higher than jute and similar to quill although mechanical properties were inferior to the latter two. In ground form, FF and jute composite properties were similar except for 34% higher modulus of jute; under the same formulation and processing conditions, ground FF composites had nearly 50% lower mechanical properties compared with ground quill composites. It was found that voids and density of composites have effect on mechanical and sound dampening properties; however, no direct relationship was found between mechanical properties and sound dampening.