Microstructure and magnetic properties of Co/Al2O3 nanocomposite powders

Nanocomposite powders of magnetic cobalt nanoparticles dispersed by nonmagnetic Al₂O₃ particles have been prepared by planetary ball milling. Ball milling of the CoO and Al mixture powder after a certain milling duration reduces CoO to (fcc and hcp) Co completely and oxidizes Al to -Al₂O₃ simultaneously. The average grain sizes of the nanocomposite powders are 19 nm for Co and 28 nm for -Al₂O₃ after the completion of the reduction reaction. By direct ball milling of the mixture of Co and Al₂O₃, the allotropic phase transformation of Co was observed and the average grain size of Co is reduced to 5 nm. For both the samples of the mechanochemical series and the direct milling series, the saturation magnetizations of the nanocomposite powders decrease with decreasing average grain size of Co. This may be due to the enhancement of the interface effects and the increase of the superparamagnetic particles with decreasing Co grain size. The coercivities of the Co/Al₂O₃ nanocomposite powders increase up to 380 Oe. The increasing grain boundaries with decreasing Co grain size result in the domain wall pinning which predicts the coercivity enhancement. In addition to the grain size effects, the reduction of the particle size toward the size region of single domain also contributes to the increase of coercivity.     

Effects of particle size of 8 mol% Y2O3 stabilized ZrO2 (YSZ) and additive Ta2O5 on the phase composition and the microstructure of sintered YSZ electrolyte

The chemical stability and sinterability of nano- and micro-sized yttria stabilized zirconia (YSZ) powders were investigated, and the effect of Ta₂O₅ additive on the sinterability of YSZ electrolyte was also studied. Addition of Ta₂O₅ easily causes phase transformation of YSZ from cubic to monoclinic, and thus unfavorable for the improvement of ionic conductivity of YSZ electrolyte. Nano-sized YSZ easily causes abnormal grain growth and hence readily results in inhomogeneous microstructure of YSZ matrix, while micro-sized YSZ displays relatively low sinterability. Comparatively, mixture with 50 wt.% nano-sized and 50 wt.% micro-sized YSZ powders exhibits high sinterability and could be sintered to homogeneous microstructure, which can be used as starting materials to prepare dense YSZ electrolyte at low temperatures.     

Mechanochemical reduction of MoO3/SiO2 powder mixtures by Al and carbon for the synthesis of nanocrystalline MoSi2

In this investigation, MoSi₂ intermetallic compound has been synthesized by reducing of MoO₃/SiO₂ powder mixtures by Al and carbon via mechanical alloying (MA). Powder mixtures were ball milled for 0–100 h and structural evolutions have been monitored by X-ray diffraction. In the Al system, both β-MoSi₂ (high temperature phase) and -MoSi₂ (low temperature phase) were obtained after 3 h of milling and after 70 h of milling the β-phase transformed to -phase. The crystallite size of -MoSi₂ and Al₂O₃ after milling for 100 h was 12 and 17 nm, respectively. In reducing with carbon, two different compositions with nominal carbon content of 13.7 and 24 wt.% were used that in both compositions, -MoSi₂ forms during 10 h of milling. Higher carbon content increases the amount of MoSi₂.     

Synthesis and characterization of molybdenum aluminide nanoparticles reinforced aluminium matrix composites

Aluminium matrix composites reinforced with molybdenum aluminide nanoparticles were synthesized by ball milling and reactive sintering of the mixture of aluminium and 10 wt% hydrated molybdenum oxide powders. Sintering the as milled powder in air below 750 °C produced MoAl₁₂ intermetallic compound nanoparticles, at 750 °C produced a mixture of MoAl₅ and MoAl₄ nanoparticles and at 800 °C under Argon atmosphere produced predominantly MoAl₄ intermetallic nano-particles in the Al matrix. The powder compacts sintered in air below 750 °C produced MoAl₁₂ whereas at 750 °C or above formed the Al matrix composite reinforced with the MoAl₅ nanoparticles. These nanoparticles become agglomerated to take up some irregular shaped flakes in the metal matrix. The reaction between Al and hydrated Mo oxide powders was found to be a favorable way to produce predominantly a particular Mo–Al intermetallic compound at a particular temperature. The Al₂O₃ particles formed as another reaction product, in all the above reactions, remain distributed in these composites. The composites thus formed were characterized by SEM-EDS, DTA, XRD and TEM analysis.     

Effect of starting powders size on the Al2O3–TiC composites

Al₂O₃–TiC composites with a content of 30 wt% TiC with various size of starting powders were manufactured by hot pressing. The Vickers hardness, bending strength and fracture toughness were studied. The experiment results show that the starting powder size has a significant effect on the properties of the Al₂O₃–TiC composites. The maximum bending strength of the submicron Al₂O₃ with the fine TiC powders addition is 712 MPa, while the maximum fracture toughness of the same Al₂O₃ matrix with the large TiC powders addition is 6.5 MPa m^1/2.     

Al2O3/TiB2/Al复合材料的微观结构和高温力学性能

以细雾化铝粉和TiB₂颗粒为原料,通过粉末冶金和热轧制制备微米TiB₂和纳米Al₂O₃颗粒增强铝基复合材料。室温时,由于TiB₂和Al₂O₃的综合强化作用,Al₂O₃/TiB₂/Al复合材料的屈服强度和抗拉强度分别为258.7 MPa和279.3 MPa,测试温度升至350℃时,TiB₂颗粒的增强效果显著减弱,原位纳米Al₂O₃颗粒与位错的交互作用使得复合材料的屈服强度和抗拉强度达到98.2MPa和122.5 MPa。经350℃退火1000 h后,由于纳米Al₂O₃对晶界的钉扎作用抑制晶粒长大,强度和硬度未发生显著的降低。     

Microstructural evolution of some MgO–TiO2 and MgO–Al2O3 powder mixtures during high-energy ball milling and post-annealing studied by X-ray diffraction

High-energy dry ball-mill and post-anneal processing were applied to synthesize MgTiO₃ and Mg₂TiO₄ single crystalline phases from the predetermined compositions of MgO–TiO₂ powder mixtures. Also, the experiments were performed to show that it is possible to prepare MgAl₂O₄ single crystalline phase from the predetermined composition of MgO–Al₂O₃ powder mixture only by employing high-energy dry ball milling, i.e. without post-annealing the milled samples. In contrast, fully developed single crystalline powders of MgTiO₃ and Mg₂TiO₄ were obtained after post-annealing the milled samples for 1 h at 900 and 1200 °C, respectively.     

Sintering characteristic of Al2O3-reinforced 2xxx series Al composite powders

Sintering characteristic of Al₂O₃-reinforced 2xxx series Al composite powders was investigated in order to obtain enhanced densification. In order to confirm the effect of the ceramic phase, Al composite powder, AMB 2905 (Al–3.2Cu–1.0Mg–5.0Al₂O₃), was used as the starting powder. Al blended powder, AMB 2712 (Al–3.8Cu–1.0Mg), was also used for comparison. The sintered density of the blended powder was about 93% of the theoretical value at 620 °C. The sintered density of the composite powder was about 95% at 630 °C. A small decrease in the density of each powder caused by swelling was observed after holding time of 10 min at the sintering temperature. After 20 min, the density slightly increased. The diffusion of the liquid phase was faster in the composite powder sintered specimen than in the blended powder sintered specimen. The liquid phase is thought to have infiltrated into the spaces between ceramic agglomerates. The results show that a greater amount of liquid phase is needed to enhance the sinterability of 2xxx series Al composite materials.     

Formation and chemical leaching effects of nonequilibrium Al0.6(Fe25Cu75) alloy powder produced by rod milling

The formation and chemical leaching effects of a nonequilibrium Al_0.6(Fe₂₅Cu₇₅)_0.4 powder produced by rod milling is described. X-ray diffraction, transmission electron microscopy, differential scanning calorimetry and vibrating sample magnetometry were used to characterize both the as-milled and leached specimens. After 400 h of milling, only the bcc AlFe phase with an amorphous phase was detected in the XRD patterns. The crystallite size for the bcc AlFe phase (110) after 400 h of milling was about 5.3 nm. The peak temperature and the crystallization temperature of the as-milled powders were 448.7 and 428.0 °C, respectively. Al atoms leaching from the as-milled bcc AlFe powders in the L1 condition did not alter the diffraction pattern significantly, even though Al atoms had been removed. After the L1 specimen was annealed at 500 °C for 1 h, the bcc AlFe phase transformed to the fcc Cu, Fe, and CuFe₂O₄ phases. The peak widths of L1 and L2 specimens were similar, but became broader than that of the as-milled powder. The saturation magnetization decreased with increasing milling time, and a value of 10.4 emu/g was reached after 400 h of milling. After cooling the specimen from 750 °C, the magnetization slowly increased at approximately 491.4 °C, indicating that the bcc AlFe phase had transformed to the fcc Cu and Fe phases.     

Enhancing High-Temperature Strength and Thermal Stability of Al_2O_3/Al Composites by High-Temperature Pre-treatment of Ultrafine Al Powders

Amorphous Al_2 O_3-reinforced Al composite(am-Al_2 O_3/Al) compacted from ultrafine Al powders for high-temperature usages confronts with drawbacks because crystallization of am-Al_2 O_3 at high temperatures will result in serious strength loss.Aiming at this unsolved problem,in this study,high-temperature Al materials with enhanced thermal stability were developed through introducing more thermally stable nano-sized particles via high-temperature pre-treatment of ultrafine A1 powders.It was found that the pre-treatment at ≤550℃ could introduce a few Al_2 O_3 in the Al matrix and increase the strength of the composites,but the strength was still below that of am-Al_2 O_3/Al because without being pinned firmly,grain boundaries(GBs) were softened at high temperature and intergranular fracture happened.When the pre-treatment was carried out at 600℃,nitridation and oxidation processes happened simultaneously,producing large numbers of intergranular(AlN+γ-Al_2 O_3) particles.GB sliding and intergranular fracture were suppressed;therefore,higher strength than that of am-Al_2 O_3/Al was realized.Furthermore,the(AIN+γ-Al_2 O_3)/Al exhibited more superior thermal stability compared to amAl_2 O_3/Al for annealing treatment at 580℃ for 8 h.Therefore,an effective way to fabricate high-temperature Al composite with enhanced thermal stability was developed in this study.     

Fabrication of Bulk (Fe,Cr)_3Al/Al_2O_3 Intermetallic Matrix Nanocomposite Through Mechanical Alloying and Sintering

In the present study,(Fe,Cr)_3Al/20 vol% Al_2O_3 nanocomposite was prepared through mechanochemical reactions during ball milling and successfully bulked using a combination of cold isostatic press and sintering at 1400 ℃ for 1 h. Two processing approaches were utilized to produce(Fe,Cr)_3Al/Al_2O_3 nanocomposite: The first was milling of Fe, Cr,Al and Fe_2O_3, while the second one was milling of Fe, Cr, Al and Cr_2O_3, both in stoichiometric condition, to synthesize(Fe,Cr)_3Al/20 vol% Al_2O_3. Structural changes of powder particles during mechanical alloying were studied by X-ray diffraction. The microstructure and the morphology of powder particles and bulk samples were also studied by scanning electron microscopy and transmission electron microscopy. Microstructural analysis showed that mechanochemical reactions took place during milling, and nanometric Al_2O_3 was uniformly distributed in the matrix. The results also showed that the second approach required a considerably higher milling time to produce(Fe,Cr)_3Al/Al_2O_3 nanocomposite, as compared to the first one. For this reason, bulk samples were produced from the synthesized nanocomposite in the first approach. The microstructure of the sintered samples consisted of a network structure of(Fe,Cr)_3Al and Al_2O_3 phases with superior mechanical properties.     

Improvement in hydrogen sorption properties of Mg by reactive mechanical grinding with Cr2O3, Al2O3 and CeO2

We tried to improve the hydrogen sorption properties of Mg by mechanical grinding under H₂ (reactive mechanical grinding) with oxides Cr₂O₃, Al₂O₃ and CeO₂. The hydriding rates of Mg are reportedly controlled by the diffusion of hydrogen through a growing Mg hydride layer. The added oxides can help pulverization of Mg during mechanical grinding. A part of Mg is transformed into MgH₂ during reactive mechanical grinding. The Mg+10wt.%Cr₂O₃ powder has the largest transformed fraction 0.215, followed in order by Mg+10wt.%CeO₂ and Mg+10wt.%Al₂O₃. The Mg+10wt.%Cr₂O₃ powder has the largest hydriding rates at the first and fifth hydriding cycle, followed in order by Mg+10wt.%Al₂O₃ and Mg+10wt.%CeO₂. Mg+10wt.%Cr₂O₃ absorbs 5.87wt.% H at 573 K, 11 bar H₂ during 60 min at the first cycle. The Mg+10wt.%Cr₂O₃ powder has the largest dehydriding rates at the first and fifth dehydriding cycle, followed by Mg+10wt.%CeO₂ and Mg+10wt.%Al₂O₃. It desorbs 4.44 wt.% H at 573 K, 0.5 bar H₂ during 60 min at the first cycle. All the samples absorb and desorb less hydrogen at the fifth cycle than at the first cycle. It is considered that this results from the agglomeration of the particles during hydriding–dehydriding cycling. The average particle sizes of the as-milled and cycled powders increase in the order of Mg+10wt.%Cr₂O₃, Mg+10wt.%Al₂O₃ and Mg+10wt.%CeO₂. The quantities of hydrogen absorbed or desorbed for 1 h for the first and fifth cycles decrease in the order of Mg+10wt.%Cr₂O₃, Mg+10wt.%Al₂O₃ and Mg+10wt.%CeO₂. The quantities of absorbed or desorbed hydrogen increase as the average particle sizes decrease. As the particle size decreases, the diffusion distance shortens. This leads to the larger hydriding and dehydriding rates. The Cr₂O₃ in the Mg+10wt.%Cr₂O₃ powder is reduced after hydriding–dehydriding cycling. The much larger chemical affinity of Mg than Cr for oxygen leads to a reduction of Cr₂O₃ after cycling.     

Preparation and luminescent properties of europium-activated YInGe2O7 phosphors

Effects of precursor milling on phase evolution and morphology of mullite (3Al₂O₃·2SiO₂) processed by solid-state reaction have been investigated. Alumina and silica powders were used as starting materials and milling was taken place in a medium energy conventional ball mill and a high-energy planetary ball mill. Milling in a conventional ball mill although decreases mullite formation temperature by 200 °C, but does not considerably change mullite phase morphology. Use of a planetary ball mill after 40 h of milling showed to be much more effective in activating the oxide precursors, and mullitization temperature was reduced to below 900 °C. Whisker like mullite was formed after sintering at 1450 °C for 2 h and volume fraction of this structure was increased by increasing the milling time. XRD results showed that samples mechanically activated for 20 h in the planetary ball mill were fully transformed to mullite after sintering at 1450 °C, whereas Al₂O₃ and SiO₂ phases were still detected in the samples milled in the conventional ball mill for 20 h and then sintered at the same conditions.     

一种可内生Al2O3扩散障的δ-Ni2Al3-Cr2O3/ Ni-Cr2O3涂层体系

通过对Ni-Cr₂O₃复合镀层620 ℃部分渗铝制备了δ-Ni₂Al₃-Cr₂O₃/Ni-Cr₂O₃涂层体系。Cr₂O₃颗粒在渗铝的过程中和Al反应生成更为稳定的Al₂O₃。1000 ℃恒温氧化20 h后发现,铝化物涂层和复合镀层内掺杂的Cr₂O₃颗粒完全转化为Al₂O₃,并在铝化物涂层/Ni镀层界面自发形成了一层Al₂O₃富集层,该富集层起扩散障作用,阻碍铝化物涂层因互扩散所致的退化。     

Toughened ZrO2 ceramics sintered with a La2O3-rich glass as additive

In this study, the influence of the glass addition and sintering parameters on the densification and mechanical properties of tetragonal zirconia polycrystals (3Y-TZP) ceramics were evaluated. High-purity tetragonal ZrO₂ powder and La₂O₃-rich glass were used as starting powders. Two compositions based on ZrO₂ and containing 5 wt.% and 10 wt.% of La₂O₃-rich glass were studied in this work. The starting powders were mixed/milled by planetary milling, dried at 90 °C for 24 h, sieved through a 60 mesh screen and uniaxially cold pressed under 80 MPa. The samples were sintered in air at 1200 °C, 1300 °C, 1400 °C for 60 min and at 1450 °C for 120 min, with heating and cooling rates of 10 °C/min. Sintered samples were characterized by relative density, X-ray diffraction (XRD) and scanning electron microscopy (SEM). Hardness and fracture toughness were obtained by Vickers indentation method. Dense sintered samples were obtained for all conditions. Furthermore, only tetragonal-ZrO₂ was identified as crystalline phase in sintered samples, independently of the conditions studied. Samples sintered at 1300 °C for 60 min presented the optimal mechanical properties with hardness and fracture toughness values near to 12 GPa and 8.5 MPa m^1/2, respectively.     

Formation of Al–Y oxide during processing of γ-TiAl

While processing Y₂O₃ dispersed γ-TiAl, Y₂O₃ particles which dissolved during hot isostatic pressing (HIP’ing) were found to precipitate during the heat treatment in the form of a mixed Al–Y oxide. To understand the chemical reaction that occurs between Y₂O₃ and γ-TiAl during the heat treatment cycle, a powder mixture comprising of γ-TiAl and 10 wt.% Y₂O₃ was mechanically alloyed (MA’d) for 8 h and the milled powder was subjected to differential thermal analysis (DTA) at 1150 °C prior to analyzing it using X-ray diffraction technique. The present study clearly demonstrates that aluminum in the combined form either as γ-TiAl or Al₂O₃ reacts in a similar manner with Y₂O₃ when milled and heat treated at 1150 °C. In either case there is formation of Al₂Y₄O₉ (2Y₂O₃.Al₂O₃).     

Friction characteristic of micro-arc oxidative Al2O3 coatings sliding against Si3N4 balls in various environments

The alumina ceramic coatings were prepared on 2024Al alloy by micro-arc oxidation (MAO) technique. The phase structure of the MAO Al₂O₃ coating was determined using X-ray diffraction. The thickness and micro-hardness of the MAO Al₂O₃ coatings was measured using eddy current thickness equipment and micro-hardness tester. The friction property of MAO Al₂O₃ coatings sliding against Si₃N₄ ceramic balls were investigated in air, water and oil by a ball-on-disk tribo-meter, and the worn surfaces of the MAO Al₂O₃ coatings were observed using scanning electron microscope (SEM). The results showed that the MAO Al₂O₃ coatings mainly contained -Al₂O₃ and γ-Al₂O₃ phase. The micro-hardness of the polished MAO coatings was HV1740 ± 87. With an increase in normal load and sliding speed, the friction coefficient in air increased from 0.74 to 0.87, while decreased from 0.72 to 0.57 in water and 0.24 to 0.11 in oil. This indicates that the fluid lubrication could improve the friction behavior of the MAO Al₂O₃ coatings. The worn surfaces' observation indicated that the wear mechanism of the MAO Al₂O₃ coatings changed from abrasive wear in air to mix wear in water, and became microploughing wear in oil.     

Synthesis of TiC–Al2O3 nanocomposite powder from impure Ti chips, Al and carbon black by mechanical alloying

The possibility of providing TiC–Al₂O₃ nanocomposite as a useful composite from low-cost raw materials has been investigated. Impure Ti chips were placed in a high energy ball mill with carbon black and aluminum powder and sampled after different times. XRD analysis showed that TiC has been synthesized after 10 h of milling. It could be observed from the width of XRD patterns’ peaks that the size of produced TiC crystallites is in the order of nanometer. In order to forming of TiC–Al₂O₃ composite, heat treatment was performed in different temperatures. Investigations have revealed that formation temperature of TiC as the dominant phase decreased for the milled specimens during heat treatment, also nanocrystalline TiC–Al₂O₃ composite was formed in this situation. Furthermore milling led to increase of strain and decrease of TiC lattice parameter while during heat treatment nanocrystalline grains grow up and strain decreases.     

The effect of sequential and continuous high-energy impact mode on the mechano-chemical synthesis of nanostructured complex hydride Mg2FeH6

The effect of sequential and continuous high-energy impact mode in the magneto-mill Uni-Ball-Mill 5 on the mechano-chemical synthesis of nanostructured ternary complex hydride Mg₂FeH₆ was studied by controlled reactive mechanical alloying (CRMA). In the sequential mode the milling vial was periodically opened under a protective gas and samples of the milled powder were extracted for microstructural examination whereas during continuous CRMA the vial was never opened up to 270 h duration. MgO was detected by XRD in sequentially milled powders while no MgO was detected in the continuously milled powder. The abundance of the nanostructured ternary complex hydride Mg₂FeH₆, produced during sequential milling, and estimated from DSC reached 44 wt.% after 188 h, and afterwards it slightly decreased to 42 wt.% after 210 and 270 h. In contrast, the DSC yield of Mg₂FeH₆ after continuous CRMA for 270 h was 57 wt.%. Much higher yield after continuous milling is attributed to the absence of MgO. This behavior provides strong evidence that MgO is a primary factor suppressing formation of Mg₂FeH₆. The DSC hydrogen desorption onset temperatures are close to 200 °C while the desorption peak temperatures for all powders are below 300 °C and the desorption process is completed within the range 10–20 min. Within the investigated nanograin size range of 5–13 nm, the DSC desorption onset and peak temperatures of β-MgH₂ and Mg₂FeH₆ do not exhibit any trend with nanograin (crystallite) size of hydrides. TPD hydrogen desorption peaks from the powders containing a single ternary complex hydride Mg₂FeH₆, are very narrow, which indicates the presence of small but well-crystallized hydride particles. Their narrowness provides good evidence that the phase composition, bulk hydrogen distribution and hydride particle size distribution are very homogeneous. The overall amount of hydrogen desorbed in TPD from single-hydride Mg₂FeH₆ powders is somewhat higher than that observed in DSC and TGA desorption.

The powder milled sequentially for 270 h and desorbed in a Sieverts-type apparatus at 250 and 290 °C, yielded about a half of the hydrogen content obtained during DSC and TGA tests. No desorption of hydrogen was detected in a Sieverts-type apparatus at 250 and 290 °C after 128 and 70 min, respectively, from the powder continuously milled for 270 h. The latter easily desorbed 3.13 and 2.83 wt.% hydrogen in DSC and TGA tests, respectively.     

SEM and TEM characterization of magnesium hydride catalyzed with Ni nano-particle or Nb2O5

The microstructures of MgH₂ catalyzed with Ni nano-particle or Nb₂O₅ mesoporous powders are examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations. For MgH₂ catalyzed with Ni, the Ni particles with the diameter smaller than 1 μm were detected on the MgH₂ particles with the diameter smaller than 5 μm by the back scattering electron (BSE) microscopy. In details, the TEM micrograph indicates that the Ni particles distribute 20 nm in diameter on MgH₂ uniformly, which was the same size as the additive doped in MgH₂ before milling. On the other hand, for MgH₂ catalyzed with Nb₂O₅, the additive particles could not be found anywhere in the BSE image. Even in the TEM micrograph by much larger magnification than the SEM micrograph, the particles corresponding to the additive cannot be observed at all. Furthermore, an energy dispersive X-ray (EDX) analysis in spots with a diameter of 20 nm indicated that the existing ratio of Mg to Nb was evaluated to 98:2, being the same as the starting ratio before milling. Therefore, the metal oxide Nb₂O₅ becomes extremely small particle that could not be observed by the present work after milling compared to metal Ni^nano.