Fabrication of porous alumina–zirconia ceramics by gel-casting and infiltration methods

Porous alumina–zirconia ceramics were obtained by infiltrating porous alumina ceramics, which were prepared by tert-butyl alcohol (TBA)-based gel-casting method. Back scattering images of the fracture surface and energy dispersive spectroscopy were performed to obtain composition profiles on the fracture surface and across sections of the sintered composites. The porosity, pore size distribution and compressive strength were also investigated. The results show that the content of zirconia can be adjusted effectively by infiltration times and it decreases with increasing distance from the surface of the samples. The porosity and compressive strength can also be controlled by the infiltration times. With increases of the infiltration times from 1 to 3 cycles, the open porosity decreases slightly from 62.43% to 56.62%, while the compressive strength of the porous alumina–zirconia ceramics increases from 13.57 ± 1.21 to 26.87 ± 2.01 MPa, indicating that the porous ceramics with high porosity and high strength can be prepared by TBA-based gel-casting method combined with the infiltration process.     

Preparation and properties of porous Ti–10Mo alloy by selective laser sintering

In this study, porous Ti–10Mo alloy was prepared from a mixture of titanium, molybdenum and epoxy resin powders by selective laser sintering preforming, debinding and sintering at 1200 °C under a pure argon atmosphere. The influence of sintering process on the porous, microstructural and mechanical properties of the porous alloy was discussed. The results indicate that the pore characteristic parameters and mechanical properties mainly depend on the holding time at 1200 °C, except that the maximum strain keeps at about 45%. The matrix microstructure is dominated by α phase with a small quantity of β phase at room temperature. As the holding time lengthens from 2 to 6 h, the average pore size and the porosity decrease from 180 to 50 μm and from 70 to 40%, respectively. Meanwhile, the Young's modulus and the compressive yield strength increase in the ranges of 10–20 GPa and 180–260 MPa, respectively. Both the porous structure and the mechanical properties of the porous Ti–10Mo alloy can be adjusted to match with those of natural bone.     

Fabrication and characterization of porous Co–Cr–Mo/58S bioglass nano-composite by using NH4HCO3 as space-holder

In the present study, Co–Cr–Mo/58S porous nano-composites were successfully fabricated by the use of space-holder and powder metallurgy techniques. The cold compacted Samples were heated at 175 °C for 2 h and then was raised to 1250 °C and held for 2 h. Scanning electron microscope (SEM) and optical microscope (OM) images of porous samples showed interconnected, isolated pores and appropriate range of pore sizes. The results of compressive strength and Young's modulus were in the range of 33–566 MPa and 0.19–4.46 GPa, respectively. In particular, the compressive strength and Young's modulus at the porosity of 38.5% were found to be similar to those of bone. The SEM images, pH values and Fourier-transform infrared spectroscopy (FTIR) results showed that apatite crystallites were formed on the surface of sample with 38.5% porosity during immersion in simulated body fluid which revealed bioactivity of this sample. In vitro cytocompatibility of the sample with 38.5% porosity was evaluated and cell growth was examined. SEM images revealed that cells grew on the surface and inside the pores. The present investigation has shown that this porous nano-composite is a promising biomaterial for bone tissue engineering by virtue of its porous structure, appropriate mechanical properties, bioactivity and biocompatibility.     

Processing and mechanical properties of porous Ti–7.5Mo alloy

Titanium (Ti) and its alloys continue to be utilized extensively for skeletal repair and dental implants. Most metallic implant materials including pure Ti and Ti alloys used today are in their solid forms and are often much stiffer than human bone. However, the elastic modulus of Ti and Ti alloys can be reduced through the introduction of a porous structure, which may also provide new bone tissue integration and vascularization abilities. In the present study, porous Ti–7.5Mo alloy scaffolds made from ball-milled alloy particles and sintered at 1100 °C for 10, 15 and 20 h respectively were successfully prepared through a space-holder sintering method. In the sintered Ti–7.5Mo, no obvious diffraction peaks of elemental Mo remained after the sintering, and a duplex α + β microstructure was confirmed from the XRD pattern. The samples made from BM15 (the alloy particles ball-milled for 15 h) had higher relative density, compressive strength and elastic modulus performance than those from BM3 and BM30 (the alloy particles ball-milled for 3 and 30 h, respectively) when they were sintered under the same conditions. Moreover, the longer sintering time lead to the higher relative density and the greater compressive strength and modulus of the sample. In this work, the strength and modulus of the sintered porous Ti–7.5Mo conforms to the basic mechanical property requirement of cancellous bones.     

Mechanical modulation and bioactive surface modification of porous Ti–10Mo alloy for bone implants

The objective of this work was to fabricate a suitable porous Ti–10Mo alloy as the human bone replacement implants. The porous Ti–10Mo alloy was fabricated by mechanical alloying and then consolidated by powder metallurgy technique. NH₄HCO₃ powder was used as space-holder. It was indicated that the mean pore size, porosity, compressive strength, and elastic modulus of porous Ti–10Mo alloy could be tailored by the amount of NH₄HCO₃, and then could be matched with those of human bones. Furthermore, porous Ti–10Mo alloy was treated by alkali heat treatment and soaked in the 1.5 times simulated body fluid (1.5SBF). It was observed that the surface and the inside pore wall of porous Ti–10Mo alloy with 25 wt.% NH₄HCO₃ covered with the apatite layer after soaked in 1.5SBF for 28 days. These phenomena indicated that the surface modified porous Ti–10Mo alloy exhibited a high potential for bone-bonding, which was expected to be used as bone tissue implant.     

Structure deformation and failure of sintered steel wire mesh under torsion loading

Sintered steel wire mesh materials with total porosities of 36.3–61.8%, which are subjected to torsion loading, have been investigated in terms of deformation mode and failure mechanism. The experiments reveal that the twisted wire’s stretching, moving and rotating are main deformation mode, which leads to most of wires orientating towards the torsion direction. The failure occurs when the oriented wires fracture continuously, and leave behind a 45° fracture surface. The shear strength and shear modulus of the tested wire mesh samples are evaluated in the range of 44–103 MPa and 47–718 MPa, respectively. With an increase in porosity both the shear strength and the shear modulus decrease.     

Fabrication of porous titanium scaffold with controlled porous structure and net-shape using magnesium as spacer

This paper reports a new approach to fabricating biocompatible porous titanium with controlled pore structure and net-shape. The method is based on using sacrificial Mg particles as space holders to produce compacts that are mechanically stable and machinable. Using magnesium granules and Ti powder, Ti/Mg compacts with transverse rupture strength (~ 85 MPa) sufficient for machining were fabricated by warm compaction, and a complex-shape Ti scaffold was eventually produced by removal of Mg granules from the net-shape compact. The pores with the average size of 132–262 μm were well distributed and interconnected. Due to anisotropy and alignment of the pores the compressive strength varied with the direction of compression. In the case of pores aligned with the direction of compression, the compressive strength values (59–280 MPa) high enough for applications in load bearing implants were achieved. To verify the possibility of controlled net-shape, conventional machining process was performed on Ti/Mg compact. Compact with screw shape and porous Ti scaffold with hemispherical cup shape were fabricated by the results. Finally, it was demonstrated by cell tests using MC3T3-E1 cell line that the porous Ti scaffolds fabricated by this technique are biocompatible.     

Porous low modulus Ti40Nb compacts with electrodeposited hydroxyapatite coating for biomedical applications

Porous ß-type non-toxic Ti40Nb alloy was prepared by compaction of mechanically alloyed powder mixed with NaCl or Mg particles as space-holder material. The compacts with porosity of 36–80% demonstrated a very low Young's modulus of ~ 1.5–3 GPa and compression strength of ~ 10–35 MPa, which is suitable for potential implant material application. Porous samples were electrochemically covered with hydroxyapatite. The influence of the deposition time and of the electrolyte concentrations on the morphology of the hydroxyapatite coating was studied. It is demonstrated that a homogenous coating of hydroxyapatite crystals with different shape and size can be obtained on the surface of the porous samples.     

Effect of heat treatment on mechanical properties of low alloy steel foams

Effect of heat treatment on compressive properties of low alloy steel foams (Fe–1.75 Ni–1.5 Cu–0.5 Mo–0.6 C) having porosities in the range of 47.4–71.5% with irregular pore shape, produced by the space holder-water leaching technique in powder metallurgy, was investigated. Low alloy steel powders were mixed with different amounts of space holder (carbamide), and then compacted at 200 MPa. Carbamide in the green compacts was removed by water leaching at room temperature. The green specimens were sintered at 1200 °C for 60 min in hydrogen atmosphere. Sintered compacts were heat treated by austenitizing at 850 °C for 30 min and then quenched at 70 °C in oil and tempered at 210 °C for 60 min. In this porosity range, compressive yield strengths of as-sintered and heat treated specimens were 28–122 MPa and 18–168 MPa, respectively. The resultant Young’s moduli of the as-sintered and heat treated specimens were 0.68–3.12 GPa and 0.47–3.47 GPa, respectively. The heat treatment enhanced the Young’s modulus and compressive yield strength of the foams having porosities in the range of 47.4–62.3%, as a consequence of matrix strengthening. However, the compressive yield stress and Young’s modulus of the heat treated foam having 71.5% porosity were lower than that of the as-sintered foam’s, as a result of cracks in the structure. The results were discussed in light of the structural findings.     

Synthesis of porous titanium implants by environmental-electro-discharge-sintering process

Porous Ti implants with various porosities were first fabricated by environmental-electro-discharging-sintering (EEDS) of atomized spherical Ti powders. Powders in two size range (50–100 and 200–250 μm) were settled by vibration into a quarts tube and subjected to a high voltage and high density current pulse. A single pulse of 0.75–2.0 kJ/0.7 g-powder, using 150, 300 and 450 μF capacitors, was applied to produce fully porous and porous-surfaced Ti implant compacts. The solid core was automatically formed in the center of the compact after discharge and porous layer consisted of particles connected in three dimensions by necks. The solid core and neck sizes increased with an increase in input energy and capacitance. On the other hand, pore volume decreased with increased capacitance and input energy due to the formation of a solid core. Capacitance and input energy are the only controllable discharge parameters even though the heat generated during a discharge is the unique parameter that determines the porosity of compact. It was shown that EEDS of spherical Ti powders can efficiently produce fully porous and porous-surfaced Ti implants with various porosities in short times (<400 μs) by manipulating the discharging conditions such as input energy and capacitance including powder size.     

Dynamic freeze casting for the production of porous titanium (Ti) scaffolds

This paper proposes dynamic freeze casting as a new manufacturing technique for producing porous Ti scaffolds with a uniform porous structure and good ductility. In this method, Ti/camphene slurries with various initial Ti contents (15, 20, and 25 vol.%) were frozen at 44 °C for 12 h in rotation, which allowed for the extensive growth of camphene crystals and the uniform construction of walls made of Ti particles. All the fabricated samples showed spherical-like pores surrounded by dense Ti walls that were uniformly formed after sintering at 1300 °C for 2 h in a vacuum. The porosity decreased from 71 to 52 vol.% with an increase in Ti content from 15 to 25 vol.%, whereas the pore size decreased from 362 to 95 μm. On the other hand, the compressive strength and stiffness increased considerably from 57 ± 4 to 183 ± 6 MPa and from 1.3 ± 0.5 to 5.0 ± 0.8 GPa, respectively, due to the decrease in the porosity of the samples.     

Processing and properties of porous titanium with high porosity coated by bioactive titania nanotubes

A porous titanium scaffold with a porosity of 70% and a pore size of about 200–300 μm was fabricated using the space-holder sintering process. Furthermore, the bioactive TiO₂ nanotubes with a tube size of approximately 100 nm were prepared successfully on the surface of the porous titanium by anodization and heat-treatment. The bioactivity of the scaffold was evaluated by immersing the samples into the simulated body fluid for 7 days. Results show that the porous titanium scaffold coated with anatase nanotubes has the superior ability of hydroxyapatite formation. Meanwhile, the scaffold has a high compressive strength of 36.8 MPa, which can be used as a cancellous bone substitute.     

Preparation of high strength macroporous hydroxyapatite scaffold

Hydroxyapatite (HAp) powder was prepared from CaNO₃·4H₂O and (NH₄)₂HPO₄ by wet-chemical method and has phase stable up to 1250 °C. High strength macroporous HAp–naphthalene (HN) and HAp–naphthalene–benzene (HNB) scaffolds were fabricated by adapting sintering method. The resulting HAp scaffolds have porosity about 60 vol.% with compressive strength of ~ 11 MPa and average pore diameter in the range of ~ 125 μm. The incorporation of benzene in HN scaffold reduces the strength whereas enhanced both the porosity and pore size distribution. XRD, FTIR, SEM and mercury porosimeter techniques were used to study the phase purity, morphology, pore size and pore size distribution of scaffold. The study compared the effect of concentration of naphthalene on strength, porosity and pore size distribution on both HN and HNB scaffold. In-vitro bioactivity studies on HN and HNB scaffolds show the nucleation of spherical carbonated apatite particles on the surface in SBF solution.     

β-Type Ti–Mo–Si ternary alloys designed for biomedical applications

In order to explore the superior performances of Ti-based biochemical materials, a series of β-type Ti–10Mo–xSi alloys were designed and prepared, based on the analysis of both biocompatible and mechanical aspects. The microstructure and mechanical properties of these alloys were investigated. It was shown that all the as cast samples primarily contain equiaxed β-Ti phase and minor α″ particles. The yield strength and Young’s modulus of the alloys are sensitively but nonlinearly affected by the Si content. These β-type Ti–10Mo–xSi alloys exhibit high compressive strength over 1121 MPa, high yield stress of 613.599–910.160 MPa, low Young’s modulus in the range of 20.719–26.612 GPa, and together with large plastic strain over 21.503%. According to the good combination of high yield strength, low Young’s modulus and excellent biocompatibility of the constituent elements, these β-type alloys offer potential advantages in biomedical field for hard tissue replacements.     

The effect of processing parameters and solid concentration on the mechanical and microstructural properties of freeze-casted macroporous hydroxyapatite scaffolds

The design and fabrication of macroporous hydroxyapatite scaffolds, which could overcome current bone tissue engineering limitations, have been considered in recent years. In the current study, controlled unidirectional freeze-casting at different cooling rates was investigated. In the first step, different slurries with initial hydroxyapatite concentrations of 7–37.5 vol.% were prepared. In the next step, different cooling rates from 2 to 14 °C/min were applied to synthesize the porous scaffold. Additionally, a sintering temperature of 1350 °C was chosen as an optimum temperature. Finally, the phase composition (by XRD), microstructure (by SEM), mechanical characteristics, and the porosity of sintered samples were assessed. The porosity of the sintered samples was in a range of 45–87% and the compressive strengths varied from 0.4 MPa to 60 MPa. The mechanical strength of the scaffolds increased as a function of initial concentration, cooling rate, and sintering temperature. With regards to mechanical strength and pore size, the samples with the initial concentration and the cooling rate of 15 vol.% and 5 °C/min, respectively, showed better results.     

Compressive behavior of C/SiC composite sandwich structure with stitched lattice core

C/SiC composite sandwich structure with stitched lattice core was fabricated by a technique that involved polymer impregnation and interweaving. The mechanical behaviors of C/SiC composite sandwich structure were investigated at room temperature. The out-of-plane compressive strength was 20.97 MPa while modulus was 1473.55 MPa. The microstructural evolution on compression fracture surfaces of the stitching yarns was investigated by scanning electron microscopy, and the damage pattern of fibers on compression fracture surface was presented and discussed. Under an in-plane compression loading, the C/SiC composite sandwich structure displayed a linear-elastic behavior until failure. The peak strength and average modulus are 165.61 MPa and 19.74 GPa, respectively. The failure of the specimen was dominated by the fracture of the facesheet.     

Lightweight geopolymer concrete containing aggregate from recycle lightweight block

In this research, the properties of lightweight geopolymer concrete containing aggregate from recycle lightweight block were studied. The recycle block was crushed and classified as fine, medium and coarse aggregates. The compressive strength and density with various liquid alkaline/ash ratios, sodium silicate/NaOH ratios, NaOH concentrations, aggregate/ash ratios and curing temperatures were tested. In addition, porosity, water absorption, and modulus of elasticity were determined. Results showed that the lightweight geopolymer blocks with satisfactory strength and density could be made. The 28-day compressive strength of 1.0–16.0 MPa, density of 860–1400 kg/m³, water absorption of 10–31% and porosity of 12–34%, and modulus of elasticity of 2.9–9.9 GPa were obtained. It can be used as lightweight geopolymer concrete for wall and partition.     

Determination of the Young’s modulus of porous ß-type Ti–40Nb by finite element analysis

Macroporous ß-type Ti–40Nb compacts with particularly low stiffness suitable for biomedical applications were successfully processed by a space-holder sintering method with a total porosity range of 50–60%. The microstructure of these samples as well as their phase composition and their mechanical properties were carefully analyzed. The samples comprise macropores with 100–300 μm size formed by NaCl space-holder particles and micropores of 1–3 μm size within the sintered Ti–Nb alloy. The correlation between the mesoscopic Young’s modulus and the microporosity of the alloy was analyzed by combining compression tests, microcomputer tomography (μCT), and finite element analysis (FE). The derived relationship permits to predict the macroscopic Young’s modulus of macroporous compacts for a known morphology of the macroporosity.     

Effects of binder system and processing parameters on formability of porous Ti/HA composite through powder injection molding

Porous titanium-hydroxyapatite (Ti/HA) composite is a developed composite material suitable for bio-medical applications. Powder injection molding (PIM) with space holder method is used to produce porous Ti/HA with mechanical properties, similar to human bone, and pores helps to initiate tissue growth. However, the differences in physical and mechanical properties of these composites are the main challenges during debinding and sintering. Therefore, the main objective is to determine effects of binder systems and processing parameters on formability of Ti/HA composite. In PIM, a binder system is necessary to produce green and ultimately sintered part. There are two binder systems and variation of sintering temperature has been used. Results revealed that Polyethylene glycol (PEG)-based binder system is applicable with NaCl space holder and optimum sintering parameters, including temperature, heating rate, and holding time of 1300 °C, 10 °C/min, and 5 h, respectively. The fabricated porous Ti/HA exhibits average porosity, pore size distribution, compressive strength, and roughness values of 55%, 60 μm to 170 μm, 370 MPa, and 0.323 μm, respectively. FESEM results showed that the pores are interconnected. It may be an appropriate material for future bio-medical applications.     

High temperature mechanical properties of low alloy steel foams produced by powder metallurgy

Cu–Ni–Mo and Mo based steel foams having different porosity levels for high temperature applications were produced by the space holder-water leaching technique in powder metallurgy. Steel powders were mixed with binder (polyvinylalcohol) and spacer (carbamide), and compacted. Spacer in the green compacts was removed by water leaching at room temperature and porous green compacts were sintered at 1200 °C for 60 min in hydrogen atmosphere. The successful application of foams at higher temperatures requires a good understanding of their high temperature mechanical properties. Compression tests were carried out on steel foams with different porosities at temperatures varying from room temperature to 600 °C in argon atmosphere. Effect of high temperature on compressive properties of the steel foams was investigated. It was found that the compressive strength of steel foams was greater at elevated temperatures than that at room temperature. This occurs across a range of temperatures up to 400 °C. Beyond this point the compressive strength decreased as the temperature increased. The reason for the enhancement of the compressive strength of Cu–Ni–Mo and Mo based steel foams is expected to be due to the effect of the dynamic age-hardening.